Convert CONFIG_SYS_MONITOR_LEN to Kconfig

[platform/kernel/u-boot.git] / include / configs / cm_t43.h

diff --git a/include/configs/cm_t43.h b/include/configs/cm_t43.h
index a290cf0..f0fbbe2 100644 (file)
--- a/include/configs/cm_t43.h
+++ b/include/configs/cm_t43.h
@@ -8,7 +8,6 @@
 #ifndef __CONFIG_CM_T43_H
 #define __CONFIG_CM_T43_H
 
-#define CONFIG_CM_T43
 #define CONFIG_MAX_RAM_BANK_SIZE       (2048 << 20)    /* 2GB */
 #define CONFIG_SYS_TIMERBASE           0x48040000      /* Use Timer2 */
 
@@ -23,17 +22,8 @@
 #endif
 
 /* NAND support */
-#define CONFIG_SYS_NAND_ONFI_DETECTION
-#define CONFIG_SYS_NAND_5_ADDR_CYCLE
-#define CONFIG_SYS_NAND_PAGE_SIZE      2048
-#define CONFIG_SYS_NAND_OOBSIZE                64
-#define CONFIG_SYS_NAND_BLOCK_SIZE     (128 * 1024)
-#define CONFIG_SYS_NAND_BAD_BLOCK_POS  NAND_LARGE_BADBLOCK_POS
 #define CONFIG_SYS_NAND_ECCSIZE                512
 #define CONFIG_SYS_NAND_ECCBYTES       14
-#define CONFIG_NAND_OMAP_ECCSCHEME     OMAP_ECC_BCH8_CODE_HW
-#define CONFIG_SYS_NAND_PAGE_COUNT     (CONFIG_SYS_NAND_BLOCK_SIZE / \
-                                        CONFIG_SYS_NAND_PAGE_SIZE)
 #define CONFIG_SYS_NAND_ECCPOS         { 2, 3, 4, 5, 6, 7, 8, 9, \
                                         10, 11, 12, 13, 14, 15, 16, 17, \
                                         18, 19, 20, 21, 22, 23, 24, 25, \
@@ -42,18 +32,10 @@
                                         42, 43, 44, 45, 46, 47, 48, 49, \
                                         50, 51, 52, 53, 54, 55, 56, 57, }
 
-/* CPSW Ethernet support */
-#define CONFIG_SYS_RX_ETH_BUFFER       64
-
-/* USB support */
-#define CONFIG_USB_XHCI_OMAP
-#define CONFIG_AM437X_USB2PHY2_HOST
-
 /* Power */
 #define CONFIG_POWER_TPS65218
 
 /* Enabling L2 Cache */
-#define CONFIG_SYS_L2_PL310
 #define CONFIG_SYS_PL310_BASE          0x48242000
 
 /*
@@ -64,7 +46,6 @@
 #define CONFIG_HSMMC2_8BIT
 
 #include <configs/ti_armv7_omap.h>
-#undef CONFIG_SYS_MONITOR_LEN
 
 #define V_OSCK                         24000000  /* Clock output from T2 */
 #define V_SCLK                         (V_OSCK)
@@ -73,7 +54,6 @@
        "loadaddr=0x80200000\0" \
        "fdtaddr=0x81200000\0" \
        "bootm_size=0x8000000\0" \
-       "autoload=no\0" \
        "console=ttyO0,115200n8\0" \
        "fdtfile=am437x-sb-som-t43.dtb\0" \
        "kernel=zImage-cm-t43\0" \
@@ -92,21 +72,7 @@
                "load mmc 1 ${fdtaddr} ${fdtfile} && " \
                "bootz ${loadaddr} - ${fdtaddr}\0"
 
-#define CONFIG_BOOTCOMMAND \
-       "mmc dev 0; " \
-       "if mmc rescan; then " \
-               "if run loadbootscript; then " \
-                       "run bootscript; " \
-               "fi; " \
-       "fi; " \
-       "mmc dev 1; " \
-       "if mmc rescan; then " \
-               "run emmcboot; " \
-       "fi;"
-
 /* SPL defines. */
-#define CONFIG_SYS_SPL_ARGS_ADDR       (CONFIG_SYS_SDRAM_BASE + (128 << 20))
-#define CONFIG_SYS_MONITOR_LEN         (512 * 1024)
 
 /* EEPROM */