Prepare v2023.10

[platform/kernel/u-boot.git] / include / configs / bcm28155_ap.h

diff --git a/include/configs/bcm28155_ap.h b/include/configs/bcm28155_ap.h
deleted file mode 100644 (file)
index 8619f54..0000000
--- a/include/configs/bcm28155_ap.h
+++ /dev/null
@@ -1,103 +0,0 @@
-/* SPDX-License-Identifier: GPL-2.0+ */
-/*
- * Copyright 2013 Broadcom Corporation.
- */
-
-#ifndef __BCM28155_AP_H
-#define __BCM28155_AP_H
-
-#include <linux/sizes.h>
-#include <asm/arch/sysmap.h>
-
-/* CPU, chip, mach, etc */
-#define CONFIG_KONA
-#define CONFIG_SKIP_LOWLEVEL_INIT
-
-/*
- * Memory configuration
- */
-
-#define CONFIG_SYS_SDRAM_BASE          0x80000000
-#define CONFIG_SYS_SDRAM_SIZE          0x80000000
-
-#define CONFIG_SYS_MALLOC_LEN          SZ_4M   /* see armv7/start.S. */
-
-/* GPIO Driver */
-#define CONFIG_KONA_GPIO
-
-/* MMC/SD Driver */
-#define CONFIG_SYS_SDIO_BASE0 SDIO1_BASE_ADDR
-#define CONFIG_SYS_SDIO_BASE1 SDIO2_BASE_ADDR
-#define CONFIG_SYS_SDIO_BASE2 SDIO3_BASE_ADDR
-#define CONFIG_SYS_SDIO_BASE3 SDIO4_BASE_ADDR
-#define CONFIG_SYS_SDIO0_MAX_CLK 48000000
-#define CONFIG_SYS_SDIO1_MAX_CLK 48000000
-#define CONFIG_SYS_SDIO2_MAX_CLK 48000000
-#define CONFIG_SYS_SDIO3_MAX_CLK 48000000
-#define CONFIG_SYS_SDIO0 "sdio1"
-#define CONFIG_SYS_SDIO1 "sdio2"
-#define CONFIG_SYS_SDIO2 "sdio3"
-#define CONFIG_SYS_SDIO3 "sdio4"
-
-/* I2C Driver */
-#define CONFIG_SYS_I2C
-#define CONFIG_SYS_I2C_KONA
-#define CONFIG_SYS_SPD_BUS_NUM 3       /* Start with PMU bus */
-#define CONFIG_SYS_MAX_I2C_BUS 4
-#define CONFIG_SYS_I2C_BASE0   BSC1_BASE_ADDR
-#define CONFIG_SYS_I2C_BASE1   BSC2_BASE_ADDR
-#define CONFIG_SYS_I2C_BASE2   BSC3_BASE_ADDR
-#define CONFIG_SYS_I2C_BASE3   PMU_BSC_BASE_ADDR
-
-/* Timer Driver */
-#define CONFIG_SYS_TIMER_RATE          32000
-#define CONFIG_SYS_TIMER_COUNTER       (TIMER_BASE_ADDR + 4) /* STCLO offset */
-
-/* Init functions */
-#define CONFIG_MISC_INIT_R     /* board's misc_init_r function */
-
-/* Some commands use this as the default load address */
-#define CONFIG_SYS_LOAD_ADDR           CONFIG_SYS_SDRAM_BASE
-
-/* No mtest functions as recommended */
-
-/*
- * This is the initial SP which is used only briefly for relocating the u-boot
- * image to the top of SDRAM. After relocation u-boot moves the stack to the
- * proper place.
- */
-#define CONFIG_SYS_INIT_SP_ADDR                CONFIG_SYS_TEXT_BASE
-
-/* Serial Info */
-#define CONFIG_SYS_NS16550_SERIAL
-/* Post pad 3 bytes after each reg addr */
-#define CONFIG_SYS_NS16550_REG_SIZE    (-4)
-#define CONFIG_SYS_NS16550_CLK         13000000
-#define CONFIG_SYS_NS16550_COM1                0x3e000000
-
-/* must fit into GPT:u-boot-env partition */
-#define CONFIG_SYS_MMC_ENV_DEV         0
-#define CONFIG_ENV_OFFSET              (0x00011a00 * 512)
-#define CONFIG_ENV_SIZE                        (8 * 512)
-
-/* console configuration */
-#define CONFIG_SYS_CBSIZE              1024    /* Console buffer size */
-#define CONFIG_SYS_MAXARGS             64
-#define CONFIG_SYS_BARGSIZE            CONFIG_SYS_CBSIZE
-
-/*
- * One partition type must be defined for part.c
- * This is necessary for the fatls command to work on an SD card
- * for example.
- */
-
-/* version string, parser, etc */
-
-#define CONFIG_MX_CYCLIC
-
-/* Initial upstream - boot to cmd prompt only */
-#define CONFIG_BOOTCOMMAND             ""
-
-#define CONFIG_USBID_ADDR              0x34052c46
-
-#endif /* __BCM28155_AP_H */