+++ /dev/null
-/*
- * (C) Copyright 2005-2007
- * Stefan Roese, DENX Software Engineering, sr@denx.de.
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-/************************************************************************
- * bamboo.h - configuration for BAMBOO board
- ***********************************************************************/
-#ifndef __CONFIG_H
-#define __CONFIG_H
-
-/*-----------------------------------------------------------------------
- * High Level Configuration Options
- *----------------------------------------------------------------------*/
-#define CONFIG_BAMBOO 1 /* Board is BAMBOO */
-#define CONFIG_440EP 1 /* Specific PPC440EP support */
-#define CONFIG_440 1 /* ... PPC440 family */
-#define CONFIG_SYS_CLK_FREQ 33333333 /* external freq to pll */
-
-#ifndef CONFIG_SYS_TEXT_BASE
-#define CONFIG_SYS_TEXT_BASE 0xFFFA0000
-#endif
-
-/*
- * Include common defines/options for all AMCC eval boards
- */
-#define CONFIG_HOSTNAME bamboo
-#include "amcc-common.h"
-
-/* Reclaim some space. */
-#undef CONFIG_SYS_LONGHELP
-
-#define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_early_init_f */
-
-/*
- * Please note that, if NAND support is enabled, the 2nd ethernet port
- * can't be used because of pin multiplexing. So, if you want to use the
- * 2nd ethernet port you have to "undef" the following define.
- */
-#define CONFIG_BAMBOO_NAND 1 /* enable nand flash support */
-
-/*-----------------------------------------------------------------------
- * Base addresses -- Note these are effective addresses where the
- * actual resources get mapped (not physical addresses)
- *----------------------------------------------------------------------*/
-#define CONFIG_SYS_FLASH_BASE 0xfff00000 /* start of FLASH */
-#define CONFIG_SYS_PCI_MEMBASE 0xa0000000 /* mapped pci memory*/
-#define CONFIG_SYS_PCI_MEMBASE1 CONFIG_SYS_PCI_MEMBASE + 0x10000000
-#define CONFIG_SYS_PCI_MEMBASE2 CONFIG_SYS_PCI_MEMBASE1 + 0x10000000
-#define CONFIG_SYS_PCI_MEMBASE3 CONFIG_SYS_PCI_MEMBASE2 + 0x10000000
-
-/*Don't change either of these*/
-#define CONFIG_SYS_PCI_BASE 0xe0000000 /* internal PCI regs*/
-/*Don't change either of these*/
-
-#define CONFIG_SYS_USB_DEVICE 0x50000000
-#define CONFIG_SYS_NVRAM_BASE_ADDR 0x80000000
-#define CONFIG_SYS_BOOT_BASE_ADDR 0xf0000000
-#define CONFIG_SYS_NAND_ADDR 0x90000000
-#define CONFIG_SYS_NAND2_ADDR 0x94000000
-
-/*-----------------------------------------------------------------------
- * Initial RAM & stack pointer (placed in SDRAM)
- *----------------------------------------------------------------------*/
-#define CONFIG_SYS_INIT_RAM_DCACHE 1 /* d-cache as init ram */
-#define CONFIG_SYS_INIT_RAM_ADDR 0x70000000 /* DCache */
-#define CONFIG_SYS_INIT_RAM_SIZE (4 << 10)
-#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
-#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
-
-/*-----------------------------------------------------------------------
- * Serial Port
- *----------------------------------------------------------------------*/
-#define CONFIG_CONS_INDEX 1 /* Use UART0 */
-#define CONFIG_SYS_EXT_SERIAL_CLOCK 11059200 /* use external 11.059MHz clk */
-
-/*-----------------------------------------------------------------------
- * NVRAM/RTC
- *
- * NOTE: The RTC registers are located at 0x7FFF0 - 0x7FFFF
- * The DS1558 code assumes this condition
- *
- *----------------------------------------------------------------------*/
-#define CONFIG_SYS_NVRAM_SIZE (0x2000 - 0x10) /* NVRAM size(8k)- RTC regs */
-#define CONFIG_RTC_DS1556 1 /* DS1556 RTC */
-
-/*-----------------------------------------------------------------------
- * Environment
- *----------------------------------------------------------------------*/
-#define CONFIG_ENV_IS_IN_FLASH 1 /* use FLASH for environment vars */
-
-/*-----------------------------------------------------------------------
- * FLASH related
- *----------------------------------------------------------------------*/
-#define CONFIG_SYS_MAX_FLASH_BANKS 3 /* number of banks */
-#define CONFIG_SYS_MAX_FLASH_SECT 256 /* sectors per device */
-
-#undef CONFIG_SYS_FLASH_CHECKSUM
-#define CONFIG_SYS_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */
-#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */
-
-#define CONFIG_SYS_FLASH_ADDR0 0x555
-#define CONFIG_SYS_FLASH_ADDR1 0x2aa
-#define CONFIG_SYS_FLASH_WORD_SIZE unsigned char
-
-#define CONFIG_SYS_FLASH_2ND_16BIT_DEV 1 /* bamboo has 8 and 16bit device */
-#define CONFIG_SYS_FLASH_2ND_ADDR 0x87800000 /* bamboo has 8 and 16bit device */
-
-#ifdef CONFIG_ENV_IS_IN_FLASH
-#define CONFIG_ENV_SECT_SIZE 0x10000 /* size of one complete sector */
-#define CONFIG_ENV_ADDR ((-CONFIG_SYS_MONITOR_LEN)-CONFIG_ENV_SECT_SIZE)
-#define CONFIG_ENV_SIZE 0x2000 /* Total Size of Environment Sector */
-
-/* Address and size of Redundant Environment Sector */
-#define CONFIG_ENV_ADDR_REDUND (CONFIG_ENV_ADDR-CONFIG_ENV_SECT_SIZE)
-#define CONFIG_ENV_SIZE_REDUND (CONFIG_ENV_SIZE)
-#endif /* CONFIG_ENV_IS_IN_FLASH */
-
-/*-----------------------------------------------------------------------
- * NAND FLASH
- *----------------------------------------------------------------------*/
-#define CONFIG_SYS_MAX_NAND_DEVICE 2
-#define CONFIG_SYS_NAND_BASE (CONFIG_SYS_NAND_ADDR + CONFIG_SYS_NAND_CS)
-#define CONFIG_SYS_NAND_BASE_LIST { CONFIG_SYS_NAND_BASE, CONFIG_SYS_NAND_ADDR + 2 }
-#define CONFIG_SYS_NAND_SELECT_DEVICE 1 /* nand driver supports mutipl. chips */
-#define CONFIG_SYS_NAND_CS 1
-
-/*-----------------------------------------------------------------------
- * DDR SDRAM
- *----------------------------------------------------------------------------- */
-#define CONFIG_SPD_EEPROM /* Use SPD EEPROM for setup */
-#undef CONFIG_DDR_ECC /* don't use ECC */
-#define CONFIG_SYS_SIMULATE_SPD_EEPROM 0xff /* simulate spd eeprom on this address */
-#define SPD_EEPROM_ADDRESS {CONFIG_SYS_SIMULATE_SPD_EEPROM, 0x50, 0x51}
-#define CONFIG_SYS_MBYTES_SDRAM (64) /* 64MB fixed size for early-sdram-init */
-#define CONFIG_PROG_SDRAM_TLB
-
-/*-----------------------------------------------------------------------
- * I2C
- *----------------------------------------------------------------------*/
-#define CONFIG_SYS_I2C_PPC4XX_SPEED_0 400000
-
-#define CONFIG_SYS_I2C_EEPROM_ADDR (0xa8>>1)
-#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 3
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 10
-
-#ifdef CONFIG_ENV_IS_IN_EEPROM
-#define CONFIG_ENV_SIZE 0x200 /* Size of Environment vars */
-#define CONFIG_ENV_OFFSET 0x0
-#endif /* CONFIG_ENV_IS_IN_EEPROM */
-
-/*
- * Default environment variables
- */
-#define CONFIG_EXTRA_ENV_SETTINGS \
- CONFIG_AMCC_DEF_ENV \
- CONFIG_AMCC_DEF_ENV_POWERPC \
- CONFIG_AMCC_DEF_ENV_PPC_OLD \
- CONFIG_AMCC_DEF_ENV_NOR_UPD \
- "kernel_addr=fff00000\0" \
- "ramdisk_addr=fff10000\0" \
- ""
-
-#define CONFIG_HAS_ETH0
-#define CONFIG_PHY_ADDR 0 /* PHY address, See schematics */
-#define CONFIG_PHY1_ADDR 1
-
-#ifndef CONFIG_BAMBOO_NAND
-#define CONFIG_HAS_ETH1 1 /* add support for "eth1addr" */
-#endif /* CONFIG_BAMBOO_NAND */
-
-#ifdef CONFIG_440EP
-/* USB */
-#define CONFIG_USB_OHCI
-
-/*Comment this out to enable USB 1.1 device*/
-#define USB_2_0_DEVICE
-#endif /*CONFIG_440EP*/
-
-/*
- * Commands additional to the ones defined in amcc-common.h
- */
-#define CONFIG_CMD_DATE
-#define CONFIG_CMD_PCI
-#define CONFIG_CMD_SDRAM
-
-#ifdef CONFIG_BAMBOO_NAND
-#define CONFIG_CMD_NAND
-#endif
-
-#define CONFIG_SUPPORT_VFAT
-
-/* Partitions */
-#define CONFIG_MAC_PARTITION
-#define CONFIG_DOS_PARTITION
-#define CONFIG_ISO_PARTITION
-
-/*-----------------------------------------------------------------------
- * PCI stuff
- *-----------------------------------------------------------------------
- */
-/* General PCI */
-#define CONFIG_PCI_INDIRECT_BRIDGE /* indirect PCI bridge support */
-#define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */
-#define CONFIG_SYS_PCI_TARGBASE 0x80000000 /* PCIaddr mapped to CONFIG_SYS_PCI_MEMBASE*/
-
-/* Board-specific PCI */
-#define CONFIG_SYS_PCI_TARGET_INIT
-#define CONFIG_SYS_PCI_MASTER_INIT
-
-#define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x10e8 /* AMCC */
-#define CONFIG_SYS_PCI_SUBSYS_ID 0xcafe /* Whatever */
-
-#endif /* __CONFIG_H */
projects / platform / kernel / u-boot.git / blobdiff