-#define CONFIG_REVISION_TAG
-
-/* Hardware drivers */
-
-/* allow to overwrite serial and ethaddr */
-#define CONFIG_ENV_OVERWRITE
-
-/*
- * USB configuration
- * Enable CONFIG_USB_MUSB_HOST for Host functionalities MSC, keyboard
- * Enable CONFIG_USB_MUSB_GADGET for Device functionalities.
- */
-#ifdef CONFIG_SPL_BUILD
-#undef CONFIG_USB_EHCI_OMAP
-#else
-#define CONFIG_OMAP_EHCI_PHY1_RESET_GPIO 57
-#endif
-
-/* I2C */
-
-/* Ethernet */
-#define CONFIG_DRIVER_TI_EMAC_USE_RMII
-#define CONFIG_BOOTP_DEFAULT
-#define CONFIG_BOOTP_DNS2
-#define CONFIG_BOOTP_SEND_HOSTNAME
-#define CONFIG_NET_RETRY_COUNT 10
-
-#define CONFIG_SYS_NAND_5_ADDR_CYCLE
-#define CONFIG_SYS_NAND_PAGE_COUNT 64
-#define CONFIG_SYS_NAND_PAGE_SIZE 2048
-#define CONFIG_SYS_NAND_OOBSIZE 64
-#define CONFIG_SYS_NAND_BLOCK_SIZE (128 * 1024)
-#define CONFIG_SYS_NAND_BAD_BLOCK_POS NAND_LARGE_BADBLOCK_POS
-#define CONFIG_SYS_NAND_ECCPOS { 2, 3, 4, 5, 6, 7, 8, 9, 10, \
+#define CFG_SYS_NAND_ECCPOS { 2, 3, 4, 5, 6, 7, 8, 9, 10, \
11, 12, 13, 14, 16, 17, 18, 19, 20, \
21, 22, 23, 24, 25, 26, 27, 28, 30, \
31, 32, 33, 34, 35, 36, 37, 38, 39, \
40, 41, 42, 44, 45, 46, 47, 48, 49, \
50, 51, 52, 53, 54, 55, 56 }
11, 12, 13, 14, 16, 17, 18, 19, 20, \
21, 22, 23, 24, 25, 26, 27, 28, 30, \
31, 32, 33, 34, 35, 36, 37, 38, 39, \
40, 41, 42, 44, 45, 46, 47, 48, 49, \
50, 51, 52, 53, 54, 55, 56 }
-#define CONFIG_SYS_NAND_ECCSIZE 512
-#define CONFIG_SYS_NAND_ECCBYTES 13
-#define CONFIG_NAND_OMAP_ECCSCHEME OMAP_ECC_BCH8_CODE_HW_DETECTION_SW
-#define CONFIG_SYS_NAND_MAX_OOBFREE 2
-#define CONFIG_SYS_NAND_MAX_ECCPOS 56
-#define CONFIG_SYS_NAND_U_BOOT_START CONFIG_SYS_TEXT_BASE
-#define CONFIG_SYS_NAND_U_BOOT_OFFS 0x80000
-#define CONFIG_SYS_NAND_SPL_KERNEL_OFFS 0x2a0000
+#define CFG_SYS_NAND_ECCSIZE 512
+#define CFG_SYS_NAND_ECCBYTES 13
+#define CFG_SYS_NAND_U_BOOT_START CONFIG_TEXT_BASE
/* NAND block size is 128 KiB. Synchronize these values with
* corresponding Device Tree entries in Linux:
* MLO(SPL) 4 * NAND_BLOCK_SIZE = 512 KiB @ 0x000000
/* NAND block size is 128 KiB. Synchronize these values with
* corresponding Device Tree entries in Linux:
* MLO(SPL) 4 * NAND_BLOCK_SIZE = 512 KiB @ 0x000000
"loadaddr=0x82000000\0" \
"console=ttyS2,115200n8\0" \
"fdtfile=am3517-evm.dtb\0" \
"loadaddr=0x82000000\0" \
"console=ttyS2,115200n8\0" \
"fdtfile=am3517-evm.dtb\0" \
-#define CONFIG_BOOTCOMMAND \
- "mmc dev ${mmcdev}; if mmc rescan; then " \
- "echo SD/MMC found on device $mmcdev; " \
- "if run loadbootenv; then " \
- "run importbootenv; " \
- "fi; " \
- "echo Checking if uenvcmd is set ...; " \
- "if test -n $uenvcmd; then " \
- "echo Running uenvcmd ...; " \
- "run uenvcmd; " \
- "fi; " \
- "echo Running default loadimage ...; " \
- "setenv bootfile zImage; " \
- "if run loadimage; then " \
- "run loadfdt; " \
- "run mmcboot; " \
- "fi; " \
- "else run nandboot; fi"
-
-/* We set the max number of command args high to avoid HUSH bugs. */
-#define CONFIG_SYS_MAXARGS 64
-
-/* Print Buffer Size */
-#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE \
- + sizeof(CONFIG_SYS_PROMPT) + 16)
-/* Boot Argument Buffer Size */
-#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE
-
-/* Monitor at start of flash */
-#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_FLASH_BASE
-
-#define CONFIG_SYS_ENV_SECT_SIZE (128 << 10) /* 128 KiB */
-
-/* Defines for SPL */
-
-#define CONFIG_SYS_MMCSD_FS_BOOT_PARTITION 1
-#define CONFIG_SPL_FS_LOAD_PAYLOAD_NAME "u-boot.img"
-
-#define CONFIG_SPL_NAND_BASE
-#define CONFIG_SPL_NAND_DRIVERS
-#define CONFIG_SPL_NAND_ECC
-