+++ /dev/null
-/*
- * (C) Copyright 2006-2008
- * Stefan Roese, DENX Software Engineering, sr@denx.de.
- *
- * See file CREDITS for list of people who contributed to this
- * project.
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation; either version 2 of
- * the License, or (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
- */
-
-#ifndef __CONFIG_H
-#define __CONFIG_H
-
-/*-----------------------------------------------------------------------
- * High Level Configuration Options
- *----------------------------------------------------------------------*/
-#define CONFIG_ALPR 1 /* Board is ebony */
-#define CONFIG_440GX 1 /* Specifc GX support */
-#define CONFIG_440 1 /* ... PPC440 family */
-#define CONFIG_4xx 1 /* ... PPC4xx family */
-#define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_pre_init */
-#define CONFIG_LAST_STAGE_INIT 1 /* call last_stage_init() */
-#define CONFIG_SYS_CLK_FREQ 33333333 /* external freq to pll */
-#define CONFIG_4xx_DCACHE /* Enable i- and d-cache */
-
-/*-----------------------------------------------------------------------
- * Base addresses -- Note these are effective addresses where the
- * actual resources get mapped (not physical addresses)
- *----------------------------------------------------------------------*/
-#define CONFIG_SYS_SDRAM_BASE 0x00000000 /* _must_ be 0 */
-#define CONFIG_SYS_FLASH_BASE 0xffe00000 /* start of FLASH */
-#define CONFIG_SYS_MONITOR_BASE 0xfffc0000 /* start of monitor */
-#define CONFIG_SYS_PCI_MEMBASE 0x80000000 /* mapped pci memory */
-#define CONFIG_SYS_PCI_MEMSIZE 0x40000000 /* size of mapped pci memory */
-#define CONFIG_SYS_PERIPHERAL_BASE 0xe0000000 /* internal peripherals */
-#define CONFIG_SYS_ISRAM_BASE 0xc0000000 /* internal SRAM */
-#define CONFIG_SYS_PCI_BASE 0xd0000000 /* internal PCI regs */
-#define CONFIG_SYS_PCI_MEMBASE1 CONFIG_SYS_PCI_MEMBASE + 0x10000000
-#define CONFIG_SYS_PCI_MEMBASE2 CONFIG_SYS_PCI_MEMBASE1 + 0x10000000
-#define CONFIG_SYS_PCI_MEMBASE3 CONFIG_SYS_PCI_MEMBASE2 + 0x10000000
-
-
-#define CONFIG_SYS_FPGA_BASE (CONFIG_SYS_PERIPHERAL_BASE + 0x08300000)
-#define CONFIG_SYS_NVRAM_BASE_ADDR (CONFIG_SYS_PERIPHERAL_BASE + 0x08000000)
-
-/*-----------------------------------------------------------------------
- * Initial RAM & stack pointer (placed in internal SRAM)
- *----------------------------------------------------------------------*/
-#define CONFIG_SYS_TEMP_STACK_OCM 1
-#define CONFIG_SYS_OCM_DATA_ADDR CONFIG_SYS_ISRAM_BASE
-#define CONFIG_SYS_INIT_RAM_ADDR CONFIG_SYS_ISRAM_BASE /* Initial RAM address */
-#define CONFIG_SYS_INIT_RAM_END 0x2000 /* End of used area in RAM */
-#define CONFIG_SYS_GBL_DATA_SIZE 128 /* num bytes initial data */
-
-#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_END - CONFIG_SYS_GBL_DATA_SIZE)
-#define CONFIG_SYS_POST_WORD_ADDR (CONFIG_SYS_GBL_DATA_OFFSET - 0x4)
-#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_POST_WORD_ADDR
-
-#define CONFIG_SYS_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Mon */
-#define CONFIG_SYS_MALLOC_LEN (128 * 1024) /* Reserve 128 kB for malloc*/
-
-/*-----------------------------------------------------------------------
- * Serial Port
- *----------------------------------------------------------------------*/
-#undef CONFIG_SYS_EXT_SERIAL_CLOCK
-#define CONFIG_BAUDRATE 115200
-#define CONFIG_UART1_CONSOLE /* define for uart1 as console */
-
-#define CONFIG_SYS_BAUDRATE_TABLE \
- {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200}
-
-/*-----------------------------------------------------------------------
- * FLASH related
- *----------------------------------------------------------------------*/
-#define CONFIG_SYS_FLASH_CFI 1 /* The flash is CFI compatible */
-#define CONFIG_FLASH_CFI_DRIVER 1 /* Use common CFI driver */
-#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of memory banks */
-#define CONFIG_SYS_MAX_FLASH_SECT 512 /* max number of sectors on one chip */
-#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE 1 /* use buffered writes (20x faster) */
-#define CONFIG_SYS_FLASH_EMPTY_INFO /* print 'E' for empty sector on flinfo */
-#define CONFIG_SYS_FLASH_QUIET_TEST 1 /* don't warn upon unknown flash */
-
-#define CONFIG_ENV_IS_IN_FLASH 1 /* use FLASH for environment vars */
-
-#define CONFIG_ENV_SECT_SIZE 0x10000 /* size of one complete sector */
-#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE-CONFIG_ENV_SECT_SIZE)
-#define CONFIG_ENV_SIZE 0x2000 /* Total Size of Environment Sector */
-
-/* Address and size of Redundant Environment Sector */
-#define CONFIG_ENV_ADDR_REDUND (CONFIG_ENV_ADDR-CONFIG_ENV_SECT_SIZE)
-#define CONFIG_ENV_SIZE_REDUND (CONFIG_ENV_SIZE)
-
-/*-----------------------------------------------------------------------
- * DDR SDRAM
- *----------------------------------------------------------------------*/
-#undef CONFIG_SPD_EEPROM /* Don't use SPD EEPROM for setup */
-#define CONFIG_SDRAM_BANK0 1 /* init onboard DDR SDRAM bank 0 */
-#undef CONFIG_SDRAM_ECC /* enable ECC support */
-#define CONFIG_SYS_SDRAM_TABLE { \
- {(256 << 20), 13, 0x000C4001}, /* 256MB mode 3, 13x10(4)*/ \
- {(64 << 20), 12, 0x00082001}} /* 64MB mode 2, 12x9(4) */
-
-/*-----------------------------------------------------------------------
- * I2C
- *----------------------------------------------------------------------*/
-#define CONFIG_HARD_I2C 1 /* I2C with hardware support */
-#undef CONFIG_SOFT_I2C /* I2C bit-banged */
-#define CONFIG_SYS_I2C_SPEED 100000 /* I2C speed and slave address */
-#define CONFIG_SYS_I2C_SLAVE 0x7F
-#define CONFIG_SYS_I2C_NOPROBES {0x69} /* Don't probe these addrs */
-
-/*-----------------------------------------------------------------------
- * I2C EEPROM (PCF8594C)
- *----------------------------------------------------------------------*/
-#define CONFIG_SYS_I2C_EEPROM_ADDR 0x54 /* EEPROM PCF8594C */
-#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 /* Bytes of address */
-/* mask of address bits that overflow into the "EEPROM chip address" */
-#define CONFIG_SYS_I2C_EEPROM_ADDR_OVERFLOW 0x07
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 3 /* The Philips PCF8594C has */
- /* 8 byte page write mode using */
- /* last 3 bits of the address */
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 40 /* and takes up to 40 msec */
-
-#define CONFIG_PREBOOT "echo;" \
- "echo Type \"run kernelx\" to boot the system;" \
- "echo"
-
-#undef CONFIG_BOOTARGS
-
-#define CONFIG_EXTRA_ENV_SETTINGS \
- "netdev=eth3\0" \
- "hostname=alpr\0" \
- "fdt_file=alpr/alpr.dtb\0" \
- "fdt_addr=400000\0" \
- "nfsargs=setenv bootargs root=/dev/nfs rw " \
- "nfsroot=${serverip}:${rootpath} ${init}\0" \
- "ramargs=setenv bootargs root=/dev/ram rw\0" \
- "addip=setenv bootargs ${bootargs} " \
- "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \
- ":${hostname}:${netdev}:off panic=1\0" \
- "addtty=setenv bootargs ${bootargs} console=ttyS1,${baudrate} " \
- "mem=193M\0" \
- "flash_nfs=run nfsargs addip addtty;" \
- "bootm ${kernel_addr}\0" \
- "flash_self=run ramargs addip addtty;" \
- "bootm ${kernel_addr} ${ramdisk_addr}\0" \
- "net_nfs=tftp 200000 ${bootfile};run nfsargs addip addtty;" \
- "bootm\0" \
- "net_nfs_fdt=tftp 200000 ${bootfile};" \
- "tftp ${fdt_addr} ${fdt_file};" \
- "run nfsargs addip addtty;" \
- "bootm 200000 - ${fdt_addr}\0" \
- "rootpath=/opt/projects/alpr/nfs_root\0" \
- "bootfile=/alpr/uImage\0" \
- "kernel_addr=fff00000\0" \
- "ramdisk_addr=fff10000\0" \
- "load=tftp 100000 /alpr/u-boot/u-boot.bin\0" \
- "update=protect off fffc0000 ffffffff;era fffc0000 ffffffff;" \
- "cp.b 100000 fffc0000 40000;" \
- "setenv filesize;saveenv\0" \
- "upd=run load update\0" \
- "ethprime=ppc_4xx_eth3\0" \
- "ethact=ppc_4xx_eth3\0" \
- "autoload=no\0" \
- "ipconfig=dhcp;setenv serverip 11.0.0.152\0" \
- "load_fpga=fpga load 0 ffe00000 10dd9a\0" \
- "mtdargs=setenv bootargs root=/dev/mtdblock6 rw " \
- "rootfstype=jffs2 init=/sbin/init\0" \
- "kernel1_mtd=nand read 200000 0 200000;run mtdargs addip addtty"\
- ";bootm 200000\0" \
- "kernel2_mtd=nand read 200000 200000 200000;run mtdargs addip " \
- "addtty;bootm 200000\0" \
- "kernel1=setenv actkernel 'kernel1';run load_fpga " \
- "kernel1_mtd\0" \
- "kernel2=setenv actkernel 'kernel2';run load_fpga " \
- "kernel2_mtd\0" \
- ""
-
-#define CONFIG_BOOTCOMMAND "run kernel2"
-
-#define CONFIG_BOOTDELAY 2 /* autoboot after 5 seconds */
-
-#define CONFIG_BAUDRATE 115200
-
-#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
-#define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
-
-#define CONFIG_PPC4xx_EMAC
-#define CONFIG_MII 1 /* MII PHY management */
-#define CONFIG_NET_MULTI 1
-#define CONFIG_PHY_ADDR 0x02 /* dummy setting, no EMAC0 used */
-#define CONFIG_PHY1_ADDR 0x03 /* dummy setting, no EMAC1 used */
-#define CONFIG_PHY2_ADDR 0x01 /* PHY address for EMAC2 */
-#define CONFIG_PHY3_ADDR 0x02 /* PHY address for EMAC3 */
-#define CONFIG_HAS_ETH0
-#define CONFIG_HAS_ETH1
-#define CONFIG_HAS_ETH2
-#define CONFIG_HAS_ETH3
-#define CONFIG_PHY_RESET 1 /* reset phy upon startup */
-#define CONFIG_M88E1111_PHY 1 /* needed for PHY specific setup*/
-#define CONFIG_PHY_GIGE 1 /* Include GbE speed/duplex detection */
-#define CONFIG_SYS_RX_ETH_BUFFER 32 /* Number of ethernet rx buffers & descriptors */
-
-#define CONFIG_NETCONSOLE /* include NetConsole support */
-
-
-/*
- * BOOTP options
- */
-#define CONFIG_BOOTP_BOOTFILESIZE
-#define CONFIG_BOOTP_BOOTPATH
-#define CONFIG_BOOTP_GATEWAY
-#define CONFIG_BOOTP_HOSTNAME
-
-
-/*
- * Command line configuration.
- */
-#include <config_cmd_default.h>
-
-#define CONFIG_CMD_ASKENV
-#define CONFIG_CMD_DHCP
-#define CONFIG_CMD_DIAG
-#define CONFIG_CMD_EEPROM
-#define CONFIG_CMD_FPGA
-#define CONFIG_CMD_I2C
-#define CONFIG_CMD_IRQ
-#define CONFIG_CMD_MII
-#define CONFIG_CMD_NAND
-#define CONFIG_CMD_NET
-#define CONFIG_CMD_PCI
-#define CONFIG_CMD_PING
-#undef CONFIG_CMD_NFS
-
-#undef CONFIG_WATCHDOG /* watchdog disabled */
-
-/*
- * Miscellaneous configurable options
- */
-#define CONFIG_SYS_LONGHELP /* undef to save memory */
-#define CONFIG_SYS_PROMPT "=> " /* Monitor Command Prompt */
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
-#else
-#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
-#endif
-#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
-#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
-#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
-
-#define CONFIG_SYS_ALT_MEMTEST 1 /* Enable more extensive memtest*/
-#define CONFIG_SYS_MEMTEST_START 0x0400000 /* memtest works on */
-#define CONFIG_SYS_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */
-
-#define CONFIG_SYS_LOAD_ADDR 0x100000 /* default load address */
-#define CONFIG_SYS_EXTBDINFO 1 /* To use extended board_into (bd_t) */
-
-#define CONFIG_SYS_HZ 1000 /* decrementer freq: 1 ms ticks */
-
-#define CONFIG_CMDLINE_EDITING 1 /* add command line history */
-#define CONFIG_LOOPW 1 /* enable loopw command */
-#define CONFIG_MX_CYCLIC 1 /* enable mdc/mwc commands */
-#define CONFIG_ZERO_BOOTDELAY_CHECK /* check for keypress on bootdelay==0 */
-#define CONFIG_VERSION_VARIABLE 1 /* include version env variable */
-
-#define CONFIG_SYS_4xx_RESET_TYPE 0x2 /* use chip reset on this board */
-
-/*-----------------------------------------------------------------------
- * PCI stuff
- *-----------------------------------------------------------------------
- */
-/* General PCI */
-#define CONFIG_PCI /* include pci support */
-#define CONFIG_PCI_PNP /* do pci plug-and-play */
-#define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */
-#define CONFIG_SYS_PCI_TARGBASE 0x80000000 /* PCIaddr mapped to CONFIG_SYS_PCI_MEMBASE */
-#define CONFIG_PCI_BOOTDELAY 1 /* enable pci bootdelay variable*/
-
-/* Board-specific PCI */
-#define CONFIG_SYS_PCI_TARGET_INIT /* let board init pci target */
-#define CONFIG_SYS_PCI_MASTER_INIT
-
-#define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x10e8 /* AMCC */
-#define CONFIG_SYS_PCI_SUBSYS_DEVICEID 0xcafe /* Whatever */
-
-/*-----------------------------------------------------------------------
- * FPGA stuff
- *-----------------------------------------------------------------------*/
-#define CONFIG_FPGA
-#define CONFIG_FPGA_ALTERA
-#define CONFIG_FPGA_CYCLON2
-#define CONFIG_SYS_FPGA_CHECK_CTRLC
-#define CONFIG_SYS_FPGA_PROG_FEEDBACK
-#define CONFIG_FPGA_COUNT 1 /* Ich habe 2 ... aber in
- Reihe geschaltet -> sollte gehen,
- aufpassen mit Datasize ist jetzt
- halt doppelt so gross ... Seite 306
- ist das mit den multiple Device in PS
- Mode erklaert ...*/
-
-/* FPGA program pin configuration */
-#define CONFIG_SYS_GPIO_CLK 18 /* FPGA clk pin (cpu output) */
-#define CONFIG_SYS_GPIO_DATA 19 /* FPGA data pin (cpu output) */
-#define CONFIG_SYS_GPIO_STATUS 20 /* FPGA status pin (cpu input) */
-#define CONFIG_SYS_GPIO_CONFIG 21 /* FPGA CONFIG pin (cpu output) */
-#define CONFIG_SYS_GPIO_CON_DON 22 /* FPGA CONFIG_DONE pin (cpu input) */
-
-#define CONFIG_SYS_GPIO_SEL_DPR 14 /* cpu output */
-#define CONFIG_SYS_GPIO_SEL_AVR 15 /* cpu output */
-#define CONFIG_SYS_GPIO_PROG_EN 23 /* cpu output */
-
-/*-----------------------------------------------------------------------
- * Definitions for GPIO setup
- *-----------------------------------------------------------------------*/
-#define CONFIG_SYS_GPIO_SHUTDOWN (0x80000000 >> 6)
-#define CONFIG_SYS_GPIO_SSD_EMPTY (0x80000000 >> 9)
-#define CONFIG_SYS_GPIO_EREADY (0x80000000 >> 26)
-#define CONFIG_SYS_GPIO_REV0 (0x80000000 >> 14)
-#define CONFIG_SYS_GPIO_REV1 (0x80000000 >> 15)
-
-/*-----------------------------------------------------------------------
- * NAND-FLASH stuff
- *-----------------------------------------------------------------------*/
-#define CONFIG_SYS_MAX_NAND_DEVICE 4
-#define CONFIG_SYS_NAND_BASE 0xF0000000 /* NAND FLASH Base Address */
-#define CONFIG_SYS_NAND_BASE_LIST { CONFIG_SYS_NAND_BASE + 0, CONFIG_SYS_NAND_BASE + 2, \
- CONFIG_SYS_NAND_BASE + 4, CONFIG_SYS_NAND_BASE + 6 }
-#define CONFIG_SYS_NAND_QUIET_TEST 1 /* don't warn upon unknown NAND flash */
-
-/*-----------------------------------------------------------------------
- * External Bus Controller (EBC) Setup
- *----------------------------------------------------------------------*/
-#define CONFIG_SYS_FLASH CONFIG_SYS_FLASH_BASE
-
-/* Memory Bank 0 (Flash Bank 0, NOR-FLASH) initialization */
-#define CONFIG_SYS_EBC_PB0AP 0x92015480
-#define CONFIG_SYS_EBC_PB0CR (CONFIG_SYS_FLASH | 0x3A000) /* BS=2MB,BU=R/W,BW=16bit */
-
-/* Memory Bank 1 (NAND-FLASH) initialization */
-#define CONFIG_SYS_EBC_PB1AP 0x01840380 /* TWT=3 */
-#define CONFIG_SYS_EBC_PB1CR (CONFIG_SYS_NAND_BASE | 0x18000) /* BS=1MB,BU=R/W,BW=8bit */
-
-/*
- * For booting Linux, the board info and command line data
- * have to be in the first 8 MB of memory, since this is
- * the maximum mapped by the Linux kernel during initialization.
- */
-#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
-
-/*
- * Internal Definitions
- *
- * Boot Flags
- */
-#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */
-#define BOOTFLAG_WARM 0x02 /* Software reboot */
-
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */
-#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */
-#endif
-
-/* pass open firmware flat tree */
-#define CONFIG_OF_LIBFDT 1
-#define CONFIG_OF_BOARD_SETUP 1
-
-#endif /* __CONFIG_H */
projects / platform / kernel / u-boot.git / blobdiff