+++ /dev/null
-/*
- * (C) Copyright 2001
- * Erik Theisen, Wave 7 Optics, etheisen@mindspring.com
- *
- * See file CREDITS for list of people who contributed to this
- * project.
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation; either version 2 of
- * the License, or (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
- */
-
-/*
- * board/config.h - configuration options, board specific
- */
-
-#ifndef __CONFIG_H
-#define __CONFIG_H
-
-/*
- * High Level Configuration Options
- * (easy to change)
- */
-
-#define CONFIG_405GP 1 /* This is a PPC405GP CPU */
-#define CONFIG_4xx 1 /* ...member of PPC405 family */
-#define CONFIG_W7O 1 /* ...on a Wave 7 Optics board */
-#define CONFIG_W7OLMG 1 /* ...specifically an LMG */
-
-#define CONFIG_SYS_TEXT_BASE 0xFFFC0000
-
-#define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_early_init_f */
-#define CONFIG_MISC_INIT_F 1 /* and misc_init_f() */
-#define CONFIG_MISC_INIT_R 1 /* and misc_init_r() */
-
-#define CONFIG_SYS_CLK_FREQ 33333333 /* external frequency to pll */
-
-#define CONFIG_BAUDRATE 9600
-#define CONFIG_BOOTDELAY 3 /* autoboot after 3 seconds */
-
-#if 1
-#define CONFIG_BOOTCOMMAND "bootvx" /* VxWorks boot command */
-#else
-#define CONFIG_BOOTCOMMAND "bootp" /* autoboot command */
-#endif
-
-#undef CONFIG_BOOTARGS
-
-#define CONFIG_LOADADDR F0080000
-
-#define CONFIG_ETHADDR 00:06:0D:00:00:00 /* Default, overridden at boot */
-#define CONFIG_OVERWRITE_ETHADDR_ONCE
-#define CONFIG_IPADDR 192.168.1.1
-#define CONFIG_NETMASK 255.255.255.0
-#define CONFIG_SERVERIP 192.168.1.2
-
-#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
-#undef CONFIG_SYS_LOADS_BAUD_CHANGE /* disallow baudrate change */
-
-#define CONFIG_PPC4xx_EMAC
-#define CONFIG_MII 1 /* MII PHY management */
-#define CONFIG_PHY_ADDR 0 /* PHY address */
-
-#define CONFIG_RTC_M48T35A 1 /* ST Electronics M48 timekeeper */
-#define CONFIG_DTT_LM75 1 /* ON Semi's LM75 */
-#define CONFIG_DTT_SENSORS {2, 4} /* Sensor addresses */
-#define CONFIG_SYS_DTT_MAX_TEMP 70
-#define CONFIG_SYS_DTT_LOW_TEMP -30
-#define CONFIG_SYS_DTT_HYSTERESIS 3
-
-
-/*
- * BOOTP options
- */
-#define CONFIG_BOOTP_BOOTFILESIZE
-#define CONFIG_BOOTP_BOOTPATH
-#define CONFIG_BOOTP_GATEWAY
-#define CONFIG_BOOTP_HOSTNAME
-
-
-/*
- * Command line configuration.
- */
-#include <config_cmd_default.h>
-
-#define CONFIG_CMD_PCI
-#define CONFIG_CMD_IRQ
-#define CONFIG_CMD_ASKENV
-#define CONFIG_CMD_DHCP
-#define CONFIG_CMD_BEDBUG
-#define CONFIG_CMD_DATE
-#define CONFIG_CMD_I2C
-#define CONFIG_CMD_EEPROM
-#define CONFIG_CMD_ELF
-#define CONFIG_CMD_BSP
-#define CONFIG_CMD_REGINFO
-#define CONFIG_CMD_DTT
-
-
-#undef CONFIG_WATCHDOG /* watchdog disabled */
-#define CONFIG_HW_WATCHDOG /* HW Watchdog, board specific */
-
-#define CONFIG_SPD_EEPROM /* SPD EEPROM for SDRAM param. */
-#define CONFIG_SPDDRAM_SILENT /* No output if spd fails */
-/*
- * Miscellaneous configurable options
- */
-#define CONFIG_SYS_LONGHELP /* undef to save memory */
-#define CONFIG_SYS_PROMPT "Wave7Optics> " /* Monitor Command Prompt */
-#undef CONFIG_SYS_HUSH_PARSER /* No hush parse for U-Boot */
-#ifdef CONFIG_SYS_HUSH_PARSER
-#endif
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
-#else
-#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
-#endif
-#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
-#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
-#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
-
-#define CONFIG_SYS_MEMTEST_START 0x0400000 /* memtest works on */
-#define CONFIG_SYS_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */
-
-#define CONFIG_CONS_INDEX 1 /* Use UART0 */
-#define CONFIG_SYS_NS16550
-#define CONFIG_SYS_NS16550_SERIAL
-#define CONFIG_SYS_NS16550_REG_SIZE 1
-#define CONFIG_SYS_NS16550_CLK get_serial_clock()
-
-#undef CONFIG_SYS_EXT_SERIAL_CLOCK /* external serial clock */
-#define CONFIG_SYS_405_UART_ERRATA_59 /* 405GP/CR Rev. D silicon */
-#define CONFIG_SYS_BASE_BAUD 384000
-
-
-/* The following table includes the supported baudrates */
-#define CONFIG_SYS_BAUDRATE_TABLE {9600}
-
-#define CONFIG_SYS_LOAD_ADDR 0x100000 /* default load address */
-#define CONFIG_SYS_EXTBDINFO 1 /* use extended board_info (bd_t) */
-
-#define CONFIG_SYS_HZ 1000 /* decrementer freq: 1 ms ticks */
-
-/*-----------------------------------------------------------------------
- * PCI stuff
- *-----------------------------------------------------------------------
- */
-#define PCI_HOST_ADAPTER 0 /* configure as pci adapter */
-#define PCI_HOST_FORCE 1 /* configure as pci host */
-#define PCI_HOST_AUTO 2 /* detected via arbiter enable */
-
-#define CONFIG_PCI /* include pci support */
-#define CONFIG_PCI_HOST PCI_HOST_AUTO /* select pci host function */
-#define CONFIG_PCI_PNP /* pci plug-and-play */
-/* resource configuration */
-#define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x1014 /* PCI Vendor ID: IBM */
-#define CONFIG_SYS_PCI_SUBSYS_DEVICEID 0x0156 /* PCI Device ID: 405GP */
-#define CONFIG_SYS_PCI_PTM1LA 0x00000000 /* point to sdram */
-#define CONFIG_SYS_PCI_PTM1MS 0x80000001 /* 2GB, enable hard-wired to 1 */
-#define CONFIG_SYS_PCI_PTM1PCI 0x00000000 /* Host: use this pci address */
-#define CONFIG_SYS_PCI_PTM2LA 0x00000000 /* disabled */
-#define CONFIG_SYS_PCI_PTM2MS 0x00000000 /* disabled */
-#define CONFIG_SYS_PCI_PTM2PCI 0x00000000 /* Host: use this pci address */
-
-/*-----------------------------------------------------------------------
- * Set up values for external bus controller
- * used by cpu_init.c
- *-----------------------------------------------------------------------
- */
- /* use PerWE instead of PCI_INT ( these functions share a pin ) */
-#define CONFIG_USE_PERWE 1
-
-/* use on chip memory ( OCM ) for temperary stack until sdram is tested */
-#define CONFIG_SYS_TEMP_STACK_OCM 1
-
-/* bank 0 is boot flash */
-/* BME=0,TWT=6,CSN=1,OEN=1,WBN=0,WBF=0,TH=2,RE=0,SOR=0,BEM=1,PEN=0 */
-#define CONFIG_SYS_W7O_EBC_PB0AP 0x03050440
-/* BAS=0xFFE,BS=0x1(2MB),BU=0x3(R/W),BW=0x0(8 bits) */
-#define CONFIG_SYS_W7O_EBC_PB0CR 0xFFE38000
-
-/* bank 1 is main flash */
-/* BME=0,TWT=9,CSN=1,OEN=1,WBN=0,WBF=0,TH=1,RE=0,SOR=0,BEM=1,PEN=0 */
-#define CONFIG_SYS_EBC_PB1AP 0x04850240
-/* BAS=0xF00,BS=0x7(128MB),BU=0x3(R/W),BW=0x10(32 bits) */
-#define CONFIG_SYS_EBC_PB1CR 0xF00FC000
-
-/* bank 2 is RTC/NVRAM */
-/* BME=0,TWT=6,CSN=0,OEN=0,WBN=0,WBF=0,TH=2,RE=0,SOR=0,BEM=1,PEN=0 */
-#define CONFIG_SYS_EBC_PB2AP 0x03000440
-/* BAS=0xFC0,BS=0x0(1MB),BU=0x3(R/W),BW=0x0(8 bits) */
-#define CONFIG_SYS_EBC_PB2CR 0xFC018000
-
-/* bank 3 is FPGA 0 */
-/* BME=0,TWT=4,CSN=0,OEN=0,WBN=0,WBF=0,TH=2,RE=0,SOR=0,BEM=0,PEN=0 */
-#define CONFIG_SYS_EBC_PB3AP 0x02000400
-/* BAS=0xFD0,BS=0x0(1MB),BU=0x3(R/W),BW=0x1(16 bits) */
-#define CONFIG_SYS_EBC_PB3CR 0xFD01A000
-
-/* bank 4 is SAM 8 bit range */
-/* BME=,TWT=,CSN=,OEN=,WBN=,WBF=,TH=,RE=,SOR=,BEM=,PEN= */
-#define CONFIG_SYS_EBC_PB4AP 0x02840380
-/* BAS=,BS=,BU=0x3(R/W),BW=0x0(8 bits) */
-#define CONFIG_SYS_EBC_PB4CR 0xFE878000
-
-/* bank 5 is SAM 16 bit range */
-/* BME=0,TWT=10,CSN=2,OEN=0,WBN=0,WBF=0,TH=6,RE=1,SOR=1,BEM=0,PEN=0 */
-#define CONFIG_SYS_EBC_PB5AP 0x05040d80
-/* BAS=,BS=,BU=0x3(R/W),BW=0x1(16 bits) */
-#define CONFIG_SYS_EBC_PB5CR 0xFD87A000
-
-/* bank 6 is unused */
-/* PB6AP = 0 */
-#define CONFIG_SYS_EBC_PB6AP 0x00000000
-/* PB6CR = 0 */
-#define CONFIG_SYS_EBC_PB6CR 0x00000000
-
-/* bank 7 is LED register */
-/* BME=0,TWT=6,CSN=1,OEN=1,WBN=0,WBF=0,TH=2,RE=0,SOR=0,BEM=1,PEN=0 */
-#define CONFIG_SYS_W7O_EBC_PB7AP 0x03050440
-/* BAS=0xFE0,BS=0x0(1MB),BU=0x3(R/W),BW=0x2(32 bits) */
-#define CONFIG_SYS_W7O_EBC_PB7CR 0xFE01C000
-
-/*-----------------------------------------------------------------------
- * Start addresses for the final memory configuration
- * (Set up by the startup code)
- * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0
- */
-#define CONFIG_SYS_SDRAM_BASE 0x00000000
-#define CONFIG_SYS_FLASH_BASE 0xFFFC0000
-#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_FLASH_BASE
-#define CONFIG_SYS_MONITOR_LEN (256 * 1024) /* Reserve 196 kB for Monitor */
-#define CONFIG_SYS_MALLOC_LEN (128 * 1024) /* Reserve 128 kB for malloc() */
-
-/*
- * For booting Linux, the board info and command line data
- * have to be in the first 8 MB of memory, since this is
- * the maximum mapped by the Linux kernel during initialization.
- */
-#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
-/*-----------------------------------------------------------------------
- * FLASH organization
- */
-#define CONFIG_SYS_MAX_FLASH_BANKS 2 /* max number of memory banks */
-#define CONFIG_SYS_MAX_FLASH_SECT 256 /* max number of sec on 1 chip */
-
-#define CONFIG_SYS_FLASH_ERASE_TOUT 120000 /* Timeout, Flash Erase, in ms */
-#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Timeout, Flash Write, in ms */
-#define CONFIG_SYS_FLASH_PROTECTION 1 /* Use real Flash protection */
-
-#if 1 /* Use NVRAM for environment variables */
-/*-----------------------------------------------------------------------
- * NVRAM organization
- */
-#define CONFIG_ENV_IS_IN_NVRAM 1 /* use NVRAM for env vars */
-#define CONFIG_SYS_NVRAM_BASE_ADDR 0xfc000000 /* NVRAM base address */
-#define CONFIG_SYS_NVRAM_SIZE (32*1024) /* NVRAM size */
-#define CONFIG_ENV_SIZE 0x1000 /* Size of Environment vars */
-/*define CONFIG_ENV_ADDR \
- (CONFIG_SYS_NVRAM_BASE_ADDR+CONFIG_SYS_NVRAM_SIZE-CONFIG_ENV_SIZE) Env */
-#define CONFIG_ENV_ADDR CONFIG_SYS_NVRAM_BASE_ADDR
-
-#else /* Use Boot Flash for environment variables */
-/*-----------------------------------------------------------------------
- * Flash EEPROM for environment
- */
-#define CONFIG_ENV_IS_IN_FLASH 1
-#define CONFIG_ENV_OFFSET 0x00040000 /* Offset of Environment Sector */
-#define CONFIG_ENV_SIZE 0x10000 /* Total Size of env. sector */
-
-#define CONFIG_ENV_SECT_SIZE 0x10000 /* see README - env sec tot sze */
-#endif
-
-/*-----------------------------------------------------------------------
- * I2C EEPROM (ATMEL 24C04N)
- */
-#define CONFIG_HARD_I2C 1 /* Hardware assisted I2C */
-#define CONFIG_PPC4XX_I2C /* use PPC4xx driver */
-#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */
-#define CONFIG_SYS_I2C_SLAVE 0x7F
-
-#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 /* EEPROM ATMEL 24C04N */
-#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 /* Bytes of address */
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 3
-#define CONFIG_SYS_I2C_MULTI_EEPROMS
-/*-----------------------------------------------------------------------
- * Definitions for Serial Presence Detect EEPROM address
- * (to get SDRAM settings)
- */
-#define SPD_EEPROM_ADDRESS 0x50 /* XXX conflicting address!!! XXX */
-
-/*
- * Init Memory Controller:
- */
-#define FLASH_BASE0_PRELIM 0xFFE00000 /* FLASH bank #0 */
-#define FLASH_BASE1_PRELIM 0xF0000000 /* FLASH bank #1 */
-
-/* On Chip Memory location */
-#define CONFIG_SYS_OCM_DATA_ADDR 0xF8000000
-#define CONFIG_SYS_OCM_DATA_SIZE 0x1000
-
-/*-----------------------------------------------------------------------
- * Definitions for initial stack pointer and data area (in RAM)
- */
-#define CONFIG_SYS_INIT_RAM_ADDR CONFIG_SYS_OCM_DATA_ADDR /* inside of SDRAM */
-#define CONFIG_SYS_INIT_RAM_SIZE CONFIG_SYS_OCM_DATA_SIZE /* Size of used area in RAM */
-#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
-#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
-
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */
-#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */
-#endif
-
-/*
- * FPGA(s) configuration
- */
-#define CONFIG_SYS_FPGA_IMAGE_LEN 0x80000 /* 512KB FPGA image */
-#define CONFIG_NUM_FPGAS 1 /* Number of FPGAs on board */
-#define CONFIG_MAX_FPGAS 6 /* Maximum number of FPGAs */
-#define CONFIG_FPGAS_BASE 0xFD000000L /* Base address of FPGAs */
-#define CONFIG_FPGAS_BANK_SIZE 0x00100000L /* FPGAs' mmap bank size */
-
-#endif /* __CONFIG_H */
projects / platform / kernel / u-boot.git / blobdiff