#define CONFIG_CMD_BSP
-#define CFG_HUSH_PARSER
-#define CFG_PROMPT_HUSH_PS2 "> "
+#define CONFIG_SYS_HUSH_PARSER
+#define CONFIG_SYS_PROMPT_HUSH_PS2 "> "
/***********************************************************
* I2C stuff:
* the MPL VCMA9 is equipped with an ATMEL 24C256 EEPROM at
* address 0x50 with 16bit addressing
***********************************************************/
#define CONFIG_HARD_I2C /* I2C with hardware support */
-#define CFG_I2C_SPEED 100000 /* I2C speed */
-#define CFG_I2C_SLAVE 0x7F /* I2C slave addr */
+#define CONFIG_SYS_I2C_SPEED 100000 /* I2C speed */
+#define CONFIG_SYS_I2C_SLAVE 0x7F /* I2C slave addr */
-#define CFG_I2C_EEPROM_ADDR 0x50
-#define CFG_I2C_EEPROM_ADDR_LEN 2
+#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50
+#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2
#define CONFIG_ENV_IS_IN_EEPROM 1 /* use EEPROM for environment vars */
#define CONFIG_ENV_OFFSET 0x000 /* environment starts at offset 0 */
#define CONFIG_ENV_SIZE 0x800 /* 2KB should be more than enough */
-#undef CFG_I2C_EEPROM_ADDR_OVERFLOW
-#define CFG_EEPROM_PAGE_WRITE_BITS 6 /* 64 bytes page write mode on 24C256 */
-#define CFG_EEPROM_PAGE_WRITE_DELAY_MS 10
+#undef CONFIG_SYS_I2C_EEPROM_ADDR_OVERFLOW
+#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 6 /* 64 bytes page write mode on 24C256 */
+#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 10
/*
* Size of malloc() pool
*/
/*#define CONFIG_MALLOC_SIZE (CONFIG_ENV_SIZE + 128*1024)*/
-#define CFG_GBL_DATA_SIZE 128 /* size in bytes reserved for initial data */
+#define CONFIG_SYS_GBL_DATA_SIZE 128 /* size in bytes reserved for initial data */
-#define CFG_MONITOR_LEN (256 * 1024)
-#define CFG_MALLOC_LEN (1024 * 1024) /* BUNZIP2 needs a lot of RAM */
+#define CONFIG_SYS_MONITOR_LEN (256 * 1024)
+#define CONFIG_SYS_MALLOC_LEN (1024 * 1024) /* BUNZIP2 needs a lot of RAM */
/*
* Hardware drivers
#define CONFIG_DOS_PARTITION 1
/* Enable needed helper functions */
-#define CFG_DEVICE_DEREGISTER /* needs device_deregister */
+#define CONFIG_SYS_DEVICE_DEREGISTER /* needs device_deregister */
/************************************************************
* RTC
/*
* Miscellaneous configurable options
*/
-#define CFG_LONGHELP /* undef to save memory */
-#define CFG_PROMPT "VCMA9 # " /* Monitor Command Prompt */
-#define CFG_CBSIZE 256 /* Console I/O Buffer Size */
-#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
-#define CFG_MAXARGS 16 /* max number of command args */
-#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */
+#define CONFIG_SYS_LONGHELP /* undef to save memory */
+#define CONFIG_SYS_PROMPT "VCMA9 # " /* Monitor Command Prompt */
+#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
+#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
+#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
+#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
-#define CFG_MEMTEST_START 0x30000000 /* memtest works on */
-#define CFG_MEMTEST_END 0x30F80000 /* 15.5 MB in DRAM */
+#define CONFIG_SYS_MEMTEST_START 0x30000000 /* memtest works on */
+#define CONFIG_SYS_MEMTEST_END 0x30F80000 /* 15.5 MB in DRAM */
-#define CFG_ALT_MEMTEST
-#define CFG_LOAD_ADDR 0x30800000 /* default load address */
+#define CONFIG_SYS_ALT_MEMTEST
+#define CONFIG_SYS_LOAD_ADDR 0x30800000 /* default load address */
-#undef CFG_CLKS_IN_HZ /* everything, incl board info, in Hz */
+#undef CONFIG_SYS_CLKS_IN_HZ /* everything, incl board info, in Hz */
/* we configure PWM Timer 4 to 1us ~ 1MHz */
-/*#define CFG_HZ 1000000 */
-#define CFG_HZ 1562500
+/*#define CONFIG_SYS_HZ 1000000 */
+#define CONFIG_SYS_HZ 1562500
/* valid baudrates */
-#define CFG_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 }
+#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 }
/* support BZIP2 compression */
#define CONFIG_BZIP2 1
#define PHYS_SDRAM_1 0x30000000 /* SDRAM Bank #1 */
#define PHYS_FLASH_1 0x00000000 /* Flash Bank #1 */
-#define CFG_FLASH_BASE PHYS_FLASH_1
+#define CONFIG_SYS_FLASH_BASE PHYS_FLASH_1
/*-----------------------------------------------------------------------
* FLASH and environment organization
#define CONFIG_AMD_LV800 1 /* uncomment this if you have a LV800 flash */
#endif
-#define CFG_MAX_FLASH_BANKS 1 /* max number of memory banks */
+#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of memory banks */
#ifdef CONFIG_AMD_LV800
#define PHYS_FLASH_SIZE 0x00100000 /* 1MB */
-#define CFG_MAX_FLASH_SECT (19) /* max number of sectors on one chip */
-#define CONFIG_ENV_ADDR (CFG_FLASH_BASE + 0x0F0000) /* addr of environment */
+#define CONFIG_SYS_MAX_FLASH_SECT (19) /* max number of sectors on one chip */
+#define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + 0x0F0000) /* addr of environment */
#endif
#ifdef CONFIG_AMD_LV400
#define PHYS_FLASH_SIZE 0x00080000 /* 512KB */
-#define CFG_MAX_FLASH_SECT (11) /* max number of sectors on one chip */
-#define CONFIG_ENV_ADDR (CFG_FLASH_BASE + 0x070000) /* addr of environment */
+#define CONFIG_SYS_MAX_FLASH_SECT (11) /* max number of sectors on one chip */
+#define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + 0x070000) /* addr of environment */
#endif
/* timeout values are in ticks */
-#define CFG_FLASH_ERASE_TOUT (5*CFG_HZ) /* Timeout for Flash Erase */
-#define CFG_FLASH_WRITE_TOUT (5*CFG_HZ) /* Timeout for Flash Write */
+#define CONFIG_SYS_FLASH_ERASE_TOUT (5*CONFIG_SYS_HZ) /* Timeout for Flash Erase */
+#define CONFIG_SYS_FLASH_WRITE_TOUT (5*CONFIG_SYS_HZ) /* Timeout for Flash Write */
#if 0
#define CONFIG_ENV_IS_IN_FLASH 1
#endif
-#define CFG_JFFS2_FIRST_BANK 0
-#define CFG_JFFS2_NUM_BANKS 1
+#define CONFIG_SYS_JFFS2_FIRST_BANK 0
+#define CONFIG_SYS_JFFS2_NUM_BANKS 1
#define MULTI_PURPOSE_SOCKET_ADDR 0x08000000
#if defined(CONFIG_CMD_NAND)
#define CONFIG_NAND_LEGACY
-#define CFG_MAX_NAND_DEVICE 1 /* Max number of NAND devices */
+#define CONFIG_SYS_MAX_NAND_DEVICE 1 /* Max number of NAND devices */
#define SECTORSIZE 512
#define ADDR_COLUMN 1
projects / platform / kernel / u-boot.git / blobdiff