i2c, soft-i2c: switch to new multibus/multiadapter support

[platform/kernel/u-boot.git] / include / configs / TQM866M.h

diff --git a/include/configs/TQM866M.h b/include/configs/TQM866M.h
index a5018d5..9104971 100644 (file)
--- a/include/configs/TQM866M.h
+++ b/include/configs/TQM866M.h
@@ -107,13 +107,11 @@
 #undef CONFIG_CAN_DRIVER               /* CAN Driver support disabled  */
 
 /* enable I2C and select the hardware/software driver */
-#undef CONFIG_HARD_I2C                 /* I2C with hardware support    */
-#define CONFIG_SOFT_I2C                1       /* I2C bit-banged               */
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_I2C_SOFT                    /* I2C bit-banged */
+#define CONFIG_SYS_I2C_SOFT_SPEED      93000   /* 93 kHz is supposed to work */
+#define CONFIG_SYS_I2C_SOFT_SLAVE      0xFE
 
-#define CONFIG_SYS_I2C_SPEED           93000   /* 93 kHz is supposed to work   */
-#define CONFIG_SYS_I2C_SLAVE           0xFE
-
-#ifdef CONFIG_SOFT_I2C
 /*
  * Software (bit-bang) I2C driver configuration
  */
@@ -129,7 +127,6 @@
 #define I2C_SCL(bit)   if(bit) immr->im_cpm.cp_pbdat |=  PB_SCL; \
                        else    immr->im_cpm.cp_pbdat &= ~PB_SCL
 #define I2C_DELAY      udelay(2)       /* 1/4 I2C clock duration */
-#endif /* CONFIG_SOFT_I2C */
 
 #define CONFIG_SYS_I2C_EEPROM_ADDR     0x50            /* EEPROM AT24C256      */
 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2               /* two byte address     */
@@ -181,9 +178,6 @@
 
 #define CONFIG_CMDLINE_EDITING 1       /* add command line history     */
 #define CONFIG_SYS_HUSH_PARSER         1       /* Use the HUSH parser          */
-#ifdef CONFIG_SYS_HUSH_PARSER
-#define        CONFIG_SYS_PROMPT_HUSH_PS2      "> "
-#endif
 
 #if defined(CONFIG_CMD_KGDB)
 #define CONFIG_SYS_CBSIZE              1024    /* Console I/O Buffer Size      */
@@ -201,8 +195,6 @@
 
 #define CONFIG_SYS_HZ                  1000    /* decrementer freq: 1 ms ticks */
 
-#define CONFIG_SYS_BAUDRATE_TABLE      { 9600, 19200, 38400, 57600, 115200 }
-
 /*
  * Low Level Configuration Settings
  * (address mappings, register initial values, etc.)
@@ -217,9 +209,8 @@
  * Definitions for initial stack pointer and data area (in DPRAM)
  */
 #define CONFIG_SYS_INIT_RAM_ADDR       CONFIG_SYS_IMMR
-#define CONFIG_SYS_INIT_RAM_END        0x2F00  /* End of used area in DPRAM    */
-#define CONFIG_SYS_GBL_DATA_SIZE       64  /* size in bytes reserved for initial data */
-#define CONFIG_SYS_GBL_DATA_OFFSET     (CONFIG_SYS_INIT_RAM_END - CONFIG_SYS_GBL_DATA_SIZE)
+#define CONFIG_SYS_INIT_RAM_SIZE       0x2F00  /* Size of used area in DPRAM   */
+#define CONFIG_SYS_GBL_DATA_OFFSET     (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
 #define CONFIG_SYS_INIT_SP_OFFSET      CONFIG_SYS_GBL_DATA_OFFSET
 
 /*-----------------------------------------------------------------------
@@ -362,6 +353,7 @@
  *-----------------------------------------------------------------------
  */
 
+#define CONFIG_IDE_PREINIT     1       /* Use preinit IDE hook */
 #define CONFIG_IDE_8xx_PCCARD  1       /* Use IDE with PC Card Adapter */
 
 #undef CONFIG_IDE_8xx_DIRECT           /* Direct IDE    not supported  */