+/* SPDX-License-Identifier: GPL-2.0+ */
/*
* (C) Copyright 2005
* Wolfgang Denk, DENX Software Engineering, wd@denx.de.
- *
- * SPDX-License-Identifier: GPL-2.0+
*/
/*
* High Level Configuration Options
*/
#define CONFIG_E300 1 /* E300 Family */
-#define CONFIG_MPC834x 1 /* MPC834x specific */
-#define CONFIG_MPC8349 1 /* MPC8349 specific */
-#define CONFIG_TQM834X 1 /* TQM834X board specific */
-
-#define CONFIG_SYS_TEXT_BASE 0x80000000
-
-/* IMMR Base Address Register, use Freescale default: 0xff400000 */
-#define CONFIG_SYS_IMMR 0xff400000
-
-/* System clock. Primary input clock when in PCI host mode */
-#define CONFIG_83XX_CLKIN 66666000 /* 66,666 MHz */
-
-/*
- * Local Bus LCRR
- * LCRR: DLL bypass, Clock divider is 8
- *
- * for CSB = 266 MHz it gives LCB clock frequency = 33 MHz
- *
- * External Local Bus rate is
- * CLKIN * HRCWL_CSB_TO_CLKIN / HRCWL_LCL_BUS_TO_SCB_CLK / LCRR_CLKDIV
- */
-#define CONFIG_SYS_LCRR_DBYP LCRR_DBYP
-#define CONFIG_SYS_LCRR_CLKDIV LCRR_CLKDIV_8
/* board pre init: do not call, nothing to do */
/* detect the number of flash banks */
-#define CONFIG_BOARD_EARLY_INIT_R
/*
* DDR Setup
*/
/* DDR is system memory*/
-#define CONFIG_SYS_DDR_BASE 0x00000000
-#define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_BASE
-#define CONFIG_SYS_DDR_SDRAM_BASE CONFIG_SYS_DDR_BASE
+#define CONFIG_SYS_SDRAM_BASE 0x00000000
#define DDR_CASLAT_25 /* CASLAT set to 2.5 */
#undef CONFIG_DDR_ECC /* only for ECC DDR module */
#undef CONFIG_SPD_EEPROM /* do not use SPD EEPROM for DDR setup */
/*
* FLASH on the Local Bus
*/
-#define CONFIG_SYS_FLASH_CFI /* use the Common Flash Interface */
-#define CONFIG_FLASH_CFI_DRIVER /* use the CFI driver */
#undef CONFIG_SYS_FLASH_CHECKSUM
#define CONFIG_SYS_FLASH_BASE 0x80000000 /* start of FLASH */
#define CONFIG_SYS_FLASH_SIZE 8 /* FLASH size in MB */
#define CONFIG_SYS_FLASH_EMPTY_INFO /* print 'E' for empty sectors */
-#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE
/*
* FLASH bank number detection
#define CONFIG_SYS_MAX_FLASH_SECT 512 /* max sectors per device */
-/* 32 bit device at 0x80000000 via GPCM (0x8000_1801) */
-#define CONFIG_SYS_BR0_PRELIM ((CONFIG_SYS_FLASH_BASE & BR_BA) \
- | BR_MS_GPCM \
- | BR_PS_32 \
- | BR_V)
-
-/* FLASH timing (0x0000_0c54) */
-#define CONFIG_SYS_OR_TIMING_FLASH (OR_GPCM_CSNT \
- | OR_GPCM_ACS_DIV4 \
- | OR_GPCM_SCY_5 \
- | OR_GPCM_TRLX)
-
-#define CONFIG_SYS_PRELIM_OR_AM OR_AM_1GB /* OR addr mask: 1 GiB */
-
-#define CONFIG_SYS_OR0_PRELIM (CONFIG_SYS_PRELIM_OR_AM \
- | CONFIG_SYS_OR_TIMING_FLASH)
-
-#define CONFIG_SYS_LBLAWAR0_PRELIM (LBLAWAR_EN | LBLAWAR_1GB)
-
- /* Window base at flash base */
-#define CONFIG_SYS_LBLAWBAR0_PRELIM CONFIG_SYS_FLASH_BASE
/* disable remaining mappings */
#define CONFIG_SYS_BR1_PRELIM 0x00000000
#define CONFIG_SYS_OR1_PRELIM 0x00000000
-#define CONFIG_SYS_LBLAWBAR1_PRELIM 0x00000000
-#define CONFIG_SYS_LBLAWAR1_PRELIM 0x00000000
#define CONFIG_SYS_BR2_PRELIM 0x00000000
#define CONFIG_SYS_OR2_PRELIM 0x00000000
-#define CONFIG_SYS_LBLAWBAR2_PRELIM 0x00000000
-#define CONFIG_SYS_LBLAWAR2_PRELIM 0x00000000
#define CONFIG_SYS_BR3_PRELIM 0x00000000
#define CONFIG_SYS_OR3_PRELIM 0x00000000
-#define CONFIG_SYS_LBLAWBAR3_PRELIM 0x00000000
-#define CONFIG_SYS_LBLAWAR3_PRELIM 0x00000000
/*
* Monitor config
/*
* Serial Port
*/
-#define CONFIG_CONS_INDEX 1
#define CONFIG_SYS_NS16550_SERIAL
#define CONFIG_SYS_NS16550_REG_SIZE 1
#define CONFIG_SYS_NS16550_CLK get_bus_freq(0)
/*
* TSEC
*/
-#define CONFIG_TSEC_ENET /* tsec ethernet support */
-#define CONFIG_MII
#define CONFIG_SYS_TSEC1_OFFSET 0x24000
#define CONFIG_SYS_TSEC1 (CONFIG_SYS_IMMR + CONFIG_SYS_TSEC1_OFFSET)
#define CONFIG_ENV_SECT_SIZE 0x20000 /* 128K (one sector) for env */
#define CONFIG_ENV_SIZE 0x8000 /* 32K max size */
#define CONFIG_ENV_ADDR_REDUND (CONFIG_ENV_ADDR + CONFIG_ENV_SECT_SIZE)
-#define CONFIG_ENV_SIZE_REDUND (CONFIG_ENV_SIZE)
#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
#define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
* BOOTP options
*/
#define CONFIG_BOOTP_BOOTFILESIZE
-#define CONFIG_BOOTP_BOOTPATH
-#define CONFIG_BOOTP_GATEWAY
-#define CONFIG_BOOTP_HOSTNAME
/*
* Miscellaneous configurable options
*/
-#define CONFIG_SYS_LONGHELP /* undef to save memory */
#define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */
-#define CONFIG_CMDLINE_EDITING 1 /* add command line history */
-#define CONFIG_AUTO_COMPLETE /* add autocompletion support */
-
-#if defined(CONFIG_CMD_KGDB)
- #define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
-#else
- #define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
-#endif
-
- /* Print Buffer Size */
-#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16)
-#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
- /* Boot Argument Buffer Size */
-#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE
-
#undef CONFIG_WATCHDOG /* watchdog disabled */
/*
/* Initial Memory map for Linux */
#define CONFIG_SYS_BOOTMAPSZ (256 << 20)
-#define CONFIG_SYS_HRCW_LOW (\
- HRCWL_LCL_BUS_TO_SCB_CLK_1X1 |\
- HRCWL_DDR_TO_SCB_CLK_1X1 |\
- HRCWL_CSB_TO_CLKIN_4X1 |\
- HRCWL_VCO_1X2 |\
- HRCWL_CORE_TO_CSB_2X1)
-
-#if defined(PCI_64BIT)
-#define CONFIG_SYS_HRCW_HIGH (\
- HRCWH_PCI_HOST |\
- HRCWH_64_BIT_PCI |\
- HRCWH_PCI1_ARBITER_ENABLE |\
- HRCWH_PCI2_ARBITER_DISABLE |\
- HRCWH_CORE_ENABLE |\
- HRCWH_FROM_0X00000100 |\
- HRCWH_BOOTSEQ_DISABLE |\
- HRCWH_SW_WATCHDOG_DISABLE |\
- HRCWH_ROM_LOC_LOCAL_16BIT |\
- HRCWH_TSEC1M_IN_GMII |\
- HRCWH_TSEC2M_IN_GMII)
-#else
-#define CONFIG_SYS_HRCW_HIGH (\
- HRCWH_PCI_HOST |\
- HRCWH_32_BIT_PCI |\
- HRCWH_PCI1_ARBITER_ENABLE |\
- HRCWH_PCI2_ARBITER_DISABLE |\
- HRCWH_CORE_ENABLE |\
- HRCWH_FROM_0X00000100 |\
- HRCWH_BOOTSEQ_DISABLE |\
- HRCWH_SW_WATCHDOG_DISABLE |\
- HRCWH_ROM_LOC_LOCAL_16BIT |\
- HRCWH_TSEC1M_IN_GMII |\
- HRCWH_TSEC2M_IN_GMII)
-#endif
-
/* System IO Config */
#define CONFIG_SYS_SICRH 0
#define CONFIG_SYS_SICRL SICRL_LDP_A
-/* i-cache and d-cache disabled */
-#define CONFIG_SYS_HID0_INIT 0x000000000
-#define CONFIG_SYS_HID0_FINAL (CONFIG_SYS_HID0_INIT | \
- HID0_ENABLE_INSTRUCTION_CACHE)
-#define CONFIG_SYS_HID2 HID2_HBE
-
-#define CONFIG_HIGH_BATS 1 /* High BATs supported */
-
-/* DDR 0 - 512M */
-#define CONFIG_SYS_IBAT0L (CONFIG_SYS_SDRAM_BASE \
- | BATL_PP_RW \
- | BATL_MEMCOHERENCE)
-#define CONFIG_SYS_IBAT0U (CONFIG_SYS_SDRAM_BASE \
- | BATU_BL_256M \
- | BATU_VS \
- | BATU_VP)
-#define CONFIG_SYS_IBAT1L (CONFIG_SYS_SDRAM_BASE + 0x10000000 \
- | BATL_PP_RW \
- | BATL_MEMCOHERENCE)
-#define CONFIG_SYS_IBAT1U (CONFIG_SYS_SDRAM_BASE + 0x10000000 \
- | BATU_BL_256M \
- | BATU_VS \
- | BATU_VP)
-
-/* stack in DCACHE @ 512M (no backing mem) */
-#define CONFIG_SYS_IBAT2L (CONFIG_SYS_INIT_RAM_ADDR \
- | BATL_PP_RW \
- | BATL_MEMCOHERENCE)
-#define CONFIG_SYS_IBAT2U (CONFIG_SYS_INIT_RAM_ADDR \
- | BATU_BL_128K \
- | BATU_VS \
- | BATU_VP)
-
/* PCI */
#ifdef CONFIG_PCI
#define CONFIG_PCI_INDIRECT_BRIDGE
-#define CONFIG_SYS_IBAT3L (CONFIG_SYS_PCI1_MEM_BASE \
- | BATL_PP_RW \
- | BATL_MEMCOHERENCE)
-#define CONFIG_SYS_IBAT3U (CONFIG_SYS_PCI1_MEM_BASE \
- | BATU_BL_256M \
- | BATU_VS \
- | BATU_VP)
-#define CONFIG_SYS_IBAT4L (CONFIG_SYS_PCI1_MMIO_BASE \
- | BATL_PP_RW \
- | BATL_MEMCOHERENCE \
- | BATL_GUARDEDSTORAGE)
-#define CONFIG_SYS_IBAT4U (CONFIG_SYS_PCI1_MMIO_BASE \
- | BATU_BL_256M \
- | BATU_VS \
- | BATU_VP)
-#define CONFIG_SYS_IBAT5L (CONFIG_SYS_PCI1_IO_BASE \
- | BATL_PP_RW \
- | BATL_CACHEINHIBIT \
- | BATL_GUARDEDSTORAGE)
-#define CONFIG_SYS_IBAT5U (CONFIG_SYS_PCI1_IO_BASE \
- | BATU_BL_16M \
- | BATU_VS \
- | BATU_VP)
-#else
-#define CONFIG_SYS_IBAT3L (0)
-#define CONFIG_SYS_IBAT3U (0)
-#define CONFIG_SYS_IBAT4L (0)
-#define CONFIG_SYS_IBAT4U (0)
-#define CONFIG_SYS_IBAT5L (0)
-#define CONFIG_SYS_IBAT5U (0)
#endif
-/* IMMRBAR */
-#define CONFIG_SYS_IBAT6L (CONFIG_SYS_IMMR \
- | BATL_PP_RW \
- | BATL_CACHEINHIBIT \
- | BATL_GUARDEDSTORAGE)
-#define CONFIG_SYS_IBAT6U (CONFIG_SYS_IMMR \
- | BATU_BL_1M \
- | BATU_VS \
- | BATU_VP)
-
-/* FLASH */
-#define CONFIG_SYS_IBAT7L (CONFIG_SYS_FLASH_BASE \
- | BATL_PP_RW \
- | BATL_CACHEINHIBIT \
- | BATL_GUARDEDSTORAGE)
-#define CONFIG_SYS_IBAT7U (CONFIG_SYS_FLASH_BASE \
- | BATU_BL_256M \
- | BATU_VS \
- | BATU_VP)
-
-#define CONFIG_SYS_DBAT0L CONFIG_SYS_IBAT0L
-#define CONFIG_SYS_DBAT0U CONFIG_SYS_IBAT0U
-#define CONFIG_SYS_DBAT1L CONFIG_SYS_IBAT1L
-#define CONFIG_SYS_DBAT1U CONFIG_SYS_IBAT1U
-#define CONFIG_SYS_DBAT2L CONFIG_SYS_IBAT2L
-#define CONFIG_SYS_DBAT2U CONFIG_SYS_IBAT2U
-#define CONFIG_SYS_DBAT3L CONFIG_SYS_IBAT3L
-#define CONFIG_SYS_DBAT3U CONFIG_SYS_IBAT3U
-#define CONFIG_SYS_DBAT4L CONFIG_SYS_IBAT4L
-#define CONFIG_SYS_DBAT4U CONFIG_SYS_IBAT4U
-#define CONFIG_SYS_DBAT5L CONFIG_SYS_IBAT5L
-#define CONFIG_SYS_DBAT5U CONFIG_SYS_IBAT5U
-#define CONFIG_SYS_DBAT6L CONFIG_SYS_IBAT6L
-#define CONFIG_SYS_DBAT6U CONFIG_SYS_IBAT6U
-#define CONFIG_SYS_DBAT7L CONFIG_SYS_IBAT7L
-#define CONFIG_SYS_DBAT7U CONFIG_SYS_IBAT7U
-
#if defined(CONFIG_CMD_KGDB)
#define CONFIG_KGDB_BAUDRATE 230400 /* speed of kgdb serial port */
#endif
/* default location for tftp and bootm */
#define CONFIG_LOADADDR 400000
-#define CONFIG_PREBOOT "echo;" \
- "echo Type \\\"run flash_nfs\\\" to mount root filesystem over NFS;" \
- "echo"
-
#define CONFIG_EXTRA_ENV_SETTINGS \
"netdev=eth0\0" \
"hostname=tqm834x\0" \
* JFFS2 partitions
*/
/* mtdparts command line support */
-#define CONFIG_MTD_DEVICE /* needed for mtdparts commands */
-#define CONFIG_FLASH_CFI_MTD
-#define MTDIDS_DEFAULT "nor0=TQM834x-0"
/* default mtd partition table */
-#define MTDPARTS_DEFAULT "mtdparts=TQM834x-0:256k(u-boot),256k(env)," \
- "1m(kernel),2m(initrd)," \
- "-(user);" \
-
#endif /* __CONFIG_H */
projects / platform / kernel / u-boot.git / blobdiff