+++ /dev/null
-/*
- * (C) Copyright 2003-2014
- * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
- *
- * (C) Copyright 2004-2006
- * Martin Krause, TQ-Systems GmbH, martin.krause@tqs.de
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-#ifndef __CONFIG_H
-#define __CONFIG_H
-
-/*
- * High Level Configuration Options
- * (easy to change)
- */
-
-#define CONFIG_MPC5200 1 /* This is an MPC5200 CPU */
-#define CONFIG_TQM5200 1 /* ... on TQM5200 module */
-#undef CONFIG_TQM5200_REV100 /* define for revision 100 modules */
-#define CONFIG_DISPLAY_BOARDINFO
-
-/*
- * Valid values for CONFIG_SYS_TEXT_BASE are:
- * 0xFC000000 boot low (standard configuration with room for
- * max 64 MByte Flash ROM)
- * 0xFFF00000 boot high (for a backup copy of U-Boot)
- * 0x00100000 boot from RAM (for testing only)
- */
-#ifndef CONFIG_SYS_TEXT_BASE
-#define CONFIG_SYS_TEXT_BASE 0xFC000000
-#endif
-
-/* On a Cameron or on a FO300 board or ... */
-#if !defined(CONFIG_CAM5200) && !defined(CONFIG_CHARON) \
- && !defined(CONFIG_FO300)
-#define CONFIG_STK52XX 1 /* ... on a STK52XX board */
-#endif
-
-#define CONFIG_SYS_MPC5XXX_CLKIN 33000000 /* ... running at 33.000000MHz */
-
-#define CONFIG_HIGH_BATS 1 /* High BATs supported */
-
-/*
- * Serial console configuration
- */
-#define CONFIG_PSC_CONSOLE 1 /* console is on PSC1 */
-#define CONFIG_BAUDRATE 115200 /* ... at 115200 bps */
-#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200, 230400 }
-#define CONFIG_BOOTCOUNT_LIMIT 1
-
-#ifdef CONFIG_FO300
-#define CONFIG_SYS_DEVICE_NULLDEV 1 /* enable null device */
-#define CONFIG_SILENT_CONSOLE 1 /* enable silent startup */
-#define CONFIG_BOARD_EARLY_INIT_F 1 /* used to detect S1 switch position */
-#define CONFIG_USB_BIN_FIXUP 1 /* for a buggy USB device */
-#if 0
-#define FO300_SILENT_CONSOLE_WHEN_S1_CLOSED 1 /* silent console on PSC1 when S1 */
- /* switch is closed */
-#endif
-
-#undef FO300_SILENT_CONSOLE_WHEN_S1_CLOSED /* silent console on PSC1 when S1 */
- /* switch is open */
-#endif /* CONFIG_FO300 */
-
-#if defined(CONFIG_CHARON) || defined(CONFIG_STK52XX)
-#define CONFIG_PS2KBD /* AT-PS/2 Keyboard */
-#define CONFIG_PS2MULT /* .. on PS/2 Multiplexer */
-#define CONFIG_PS2SERIAL 6 /* .. on PSC6 */
-#define CONFIG_PS2MULT_DELAY (CONFIG_SYS_HZ/2) /* Initial delay */
-#define CONFIG_BOARD_EARLY_INIT_R
-#endif /* CONFIG_STK52XX */
-
-/*
- * PCI Mapping:
- * 0x40000000 - 0x4fffffff - PCI Memory
- * 0x50000000 - 0x50ffffff - PCI IO Space
- */
-#if defined(CONFIG_CHARON) || defined(CONFIG_STK52XX)
-#define CONFIG_PCI 1
-#define CONFIG_PCI_PNP 1
-/* #define CONFIG_PCI_SCAN_SHOW 1 */
-
-#define CONFIG_PCI_MEM_BUS 0x40000000
-#define CONFIG_PCI_MEM_PHYS CONFIG_PCI_MEM_BUS
-#define CONFIG_PCI_MEM_SIZE 0x10000000
-
-#define CONFIG_PCI_IO_BUS 0x50000000
-#define CONFIG_PCI_IO_PHYS CONFIG_PCI_IO_BUS
-#define CONFIG_PCI_IO_SIZE 0x01000000
-
-#define CONFIG_EEPRO100 1
-#define CONFIG_SYS_RX_ETH_BUFFER 8 /* use 8 rx buffer on eepro100 */
-#define CONFIG_NS8382X 1
-#endif /* CONFIG_STK52XX */
-
-/*
- * Video console
- */
-#ifndef CONFIG_TQM5200S /* No graphics controller on TQM5200S */
-#define CONFIG_VIDEO
-#define CONFIG_VIDEO_SM501
-#define CONFIG_VIDEO_SM501_32BPP
-#define CONFIG_CFB_CONSOLE
-#define CONFIG_VIDEO_LOGO
-
-#ifndef CONFIG_FO300
-#define CONFIG_CONSOLE_EXTRA_INFO
-#else
-#define CONFIG_VIDEO_BMP_LOGO
-#endif
-
-#define CONFIG_VGA_AS_SINGLE_DEVICE
-#define CONFIG_VIDEO_SW_CURSOR
-#define CONFIG_SPLASH_SCREEN
-#define CONFIG_SYS_CONSOLE_IS_IN_ENV
-#endif /* #ifndef CONFIG_TQM5200S */
-
-
-/* Partitions */
-#define CONFIG_MAC_PARTITION
-#define CONFIG_DOS_PARTITION
-#define CONFIG_ISO_PARTITION
-
-/* USB */
-#if defined(CONFIG_CHARON) || defined(CONFIG_FO300) || \
- defined(CONFIG_STK52XX)
-#define CONFIG_USB_OHCI_NEW
-#define CONFIG_SYS_OHCI_BE_CONTROLLER
-#define CONFIG_USB_STORAGE
-#define CONFIG_CMD_FAT
-
-#undef CONFIG_SYS_USB_OHCI_BOARD_INIT
-#define CONFIG_SYS_USB_OHCI_CPU_INIT
-#define CONFIG_SYS_USB_OHCI_REGS_BASE MPC5XXX_USB
-#define CONFIG_SYS_USB_OHCI_SLOT_NAME "mpc5200"
-#define CONFIG_SYS_USB_OHCI_MAX_ROOT_PORTS 15
-
-#endif
-
-#ifndef CONFIG_CAM5200
-/* POST support */
-#define CONFIG_POST (CONFIG_SYS_POST_MEMORY | \
- CONFIG_SYS_POST_CPU | \
- CONFIG_SYS_POST_I2C)
-#endif
-
-#ifdef CONFIG_POST
-/* preserve space for the post_word at end of on-chip SRAM */
-#define MPC5XXX_SRAM_POST_SIZE MPC5XXX_SRAM_SIZE-4
-#endif
-
-
-/*
- * BOOTP options
- */
-#define CONFIG_BOOTP_BOOTFILESIZE
-#define CONFIG_BOOTP_BOOTPATH
-#define CONFIG_BOOTP_GATEWAY
-#define CONFIG_BOOTP_HOSTNAME
-
-
-/*
- * Command line configuration.
- */
-#define CONFIG_CMD_ASKENV
-#define CONFIG_CMD_DATE
-#define CONFIG_CMD_EEPROM
-#define CONFIG_CMD_JFFS2
-#define CONFIG_CMD_MII
-#define CONFIG_CMD_REGINFO
-#define CONFIG_CMD_BSP
-
-#ifdef CONFIG_VIDEO
- #define CONFIG_CMD_BMP
-#endif
-
-#ifdef CONFIG_PCI
-#define CONFIG_CMD_PCI
-#define CONFIG_PCIAUTO_SKIP_HOST_BRIDGE 1
-#endif
-
-#if defined(CONFIG_CHARON) || defined(CONFIG_FO300) || \
- defined(CONFIG_MINIFAP) || defined(CONFIG_STK52XX)
- #define CONFIG_CMD_IDE
- #define CONFIG_CMD_FAT
- #define CONFIG_CMD_EXT2
-#endif
-
-#if defined(CONFIG_CHARON) || defined(CONFIG_FO300) || \
- defined(CONFIG_STK52XX)
- #define CONFIG_CFG_USB
- #define CONFIG_CFG_FAT
-#endif
-
-#ifdef CONFIG_POST
- #define CONFIG_CMD_DIAG
-#endif
-
-
-#define CONFIG_TIMESTAMP /* display image timestamps */
-
-#if (CONFIG_SYS_TEXT_BASE != 0xFFF00000)
-# define CONFIG_SYS_LOWBOOT 1 /* Boot low */
-#endif
-
-/*
- * Autobooting
- */
-#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */
-
-#define CONFIG_PREBOOT "echo;" \
- "echo Type \\\"run flash_nfs\\\" to mount root filesystem over NFS;" \
- "echo"
-
-#undef CONFIG_BOOTARGS
-
-#if defined(CONFIG_TQM5200_B) && !defined(CONFIG_SYS_LOWBOOT)
-# define ENV_UPDT \
- "update=protect off FFF00000 +${filesize};" \
- "erase FFF00000 +${filesize};" \
- "cp.b 200000 FFF00000 ${filesize};" \
- "protect on FFF00000 +${filesize}\0"
-#else /* default lowboot configuration */
-# define ENV_UPDT \
- "update=protect off FC000000 +${filesize};" \
- "erase FC000000 +${filesize};" \
- "cp.b 200000 FC000000 ${filesize};" \
- "protect on FC000000 +${filesize}\0"
-#endif
-
-#if defined(CONFIG_TQM5200)
-#define CUSTOM_ENV_SETTINGS \
- "hostname=tqm5200\0" \
- "bootfile=/tftpboot/tqm5200/uImage\0" \
- "fdt_file=/tftpboot/tqm5200/tqm5200.dtb\0" \
- "u-boot=/tftpboot/tqm5200/u-boot.bin\0"
-#elif defined(CONFIG_CAM5200)
-#define CUSTOM_ENV_SETTINGS \
- "bootfile=cam5200/uImage\0" \
- "u-boot=cam5200/u-boot.bin\0" \
- "setup=tftp 200000 cam5200/setup.img; source 200000\0"
-#endif
-
-#if defined(CONFIG_TQM5200_B)
-#define ENV_FLASH_LAYOUT \
- "fdt_addr=FC100000\0" \
- "kernel_addr=FC140000\0" \
- "ramdisk_addr=FC600000\0"
-#elif defined(CONFIG_CHARON)
-#define ENV_FLASH_LAYOUT \
- "fdt_addr=FDFC0000\0" \
- "kernel_addr=FC0A0000\0" \
- "ramdisk_addr=FC200000\0"
-#else /* !CONFIG_TQM5200_B */
-#define ENV_FLASH_LAYOUT \
- "fdt_addr=FC0A0000\0" \
- "kernel_addr=FC0C0000\0" \
- "ramdisk_addr=FC300000\0"
-#endif
-
-#define CONFIG_EXTRA_ENV_SETTINGS \
- "netdev=eth0\0" \
- "console=ttyPSC0\0" \
- ENV_FLASH_LAYOUT \
- "kernel_addr_r=400000\0" \
- "fdt_addr_r=600000\0" \
- "rootpath=/opt/eldk/ppc_6xx\0" \
- "ramargs=setenv bootargs root=/dev/ram rw\0" \
- "nfsargs=setenv bootargs root=/dev/nfs rw " \
- "nfsroot=${serverip}:${rootpath}\0" \
- "addip=setenv bootargs ${bootargs} " \
- "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \
- ":${hostname}:${netdev}:off panic=1\0" \
- "addcons=setenv bootargs ${bootargs} " \
- "console=${console},${baudrate}\0" \
- "addmtd=setenv bootargs ${bootargs} ${mtdparts}\0" \
- "flash_self_old=sete console ttyS0; " \
- "run ramargs addip addcons addmtd; " \
- "bootm ${kernel_addr} ${ramdisk_addr}\0" \
- "flash_self=run ramargs addip addcons;" \
- "bootm ${kernel_addr} ${ramdisk_addr} ${fdt_addr}\0" \
- "flash_nfs_old=sete console ttyS0; run nfsargs addip addcons;" \
- "bootm ${kernel_addr}\0" \
- "flash_nfs=run nfsargs addip addcons;" \
- "bootm ${kernel_addr} - ${fdt_addr}\0" \
- "net_nfs_old=tftp ${kernel_addr_r} ${bootfile};" \
- "sete console ttyS0; run nfsargs addip addcons;bootm\0" \
- "net_nfs=tftp ${kernel_addr_r} ${bootfile}; " \
- "tftp ${fdt_addr_r} ${fdt_file}; " \
- "run nfsargs addip addcons addmtd; " \
- "bootm ${kernel_addr_r} - ${fdt_addr_r}\0" \
- CUSTOM_ENV_SETTINGS \
- "load=tftp 200000 ${u-boot}\0" \
- ENV_UPDT \
- ""
-
-#define CONFIG_BOOTCOMMAND "run net_nfs"
-
-/*
- * IPB Bus clocking configuration.
- */
-#define CONFIG_SYS_IPBCLK_EQUALS_XLBCLK /* define for 133MHz speed */
-
-#if defined(CONFIG_SYS_IPBCLK_EQUALS_XLBCLK) && !defined(CONFIG_CAM5200)
-/*
- * PCI Bus clocking configuration
- *
- * Actually a PCI Clock of 66 MHz is only set (in cpu_init.c) if
- * CONFIG_SYS_IPBCLK_EQUALS_XLBCLK is defined. This is because a PCI Clock of
- * 66 MHz yet hasn't been tested with a IPB Bus Clock of 66 MHz.
- */
-#define CONFIG_SYS_PCICLK_EQUALS_IPBCLK_DIV2 /* define for 66MHz speed */
-#endif
-
-/*
- * I2C configuration
- */
-#define CONFIG_HARD_I2C 1 /* I2C with hardware support */
-#ifdef CONFIG_TQM5200_REV100
-#define CONFIG_SYS_I2C_MODULE 1 /* Select I2C module #1 for rev. 100 board */
-#else
-#define CONFIG_SYS_I2C_MODULE 2 /* Select I2C module #2 for all other revs */
-#endif
-
-/*
- * I2C clock frequency
- *
- * Please notice, that the resulting clock frequency could differ from the
- * configured value. This is because the I2C clock is derived from system
- * clock over a frequency divider with only a few divider values. U-Boot
- * calculates the best approximation for CONFIG_SYS_I2C_SPEED. However the calculated
- * approximation allways lies below the configured value, never above.
- */
-#define CONFIG_SYS_I2C_SPEED 100000 /* 100 kHz */
-#define CONFIG_SYS_I2C_SLAVE 0x7F
-
-/*
- * EEPROM configuration for onboard EEPROM M24C32 (M24C64 should work
- * also). For other EEPROMs configuration should be verified. On Mini-FAP the
- * EEPROM (24C64) is on the same I2C address (but on other I2C bus), so the
- * same configuration could be used.
- */
-#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 /* 1010000x */
-#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 5 /* =32 Bytes per write */
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 20
-
-/*
- * HW-Monitor configuration on Mini-FAP
- */
-#if defined (CONFIG_MINIFAP)
-#define CONFIG_SYS_I2C_HWMON_ADDR 0x2C
-#endif
-
-/* List of I2C addresses to be verified by POST */
-#if defined (CONFIG_MINIFAP)
-#undef CONFIG_SYS_POST_I2C_ADDRS
-#define CONFIG_SYS_POST_I2C_ADDRS {CONFIG_SYS_I2C_EEPROM_ADDR, \
- CONFIG_SYS_I2C_HWMON_ADDR, \
- CONFIG_SYS_I2C_SLAVE}
-#endif
-
-/*
- * Flash configuration
- */
-#define CONFIG_SYS_FLASH_BASE 0xFC000000
-
-#if defined(CONFIG_CAM5200) && defined(CONFIG_CAM5200_NIOSFLASH)
-#define CONFIG_SYS_MAX_FLASH_BANKS 2 /* max num of flash banks
- (= chip selects) */
-#define CONFIG_SYS_FLASH_WORD_SIZE unsigned int /* main flash device with */
-#define CONFIG_SYS_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */
-#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */
-
-#define CONFIG_SYS_FLASH_ADDR0 0x555
-#define CONFIG_SYS_FLASH_ADDR1 0x2AA
-#define CONFIG_SYS_FLASH_2ND_16BIT_DEV 1 /* NIOS flash is a 16bit device */
-#define CONFIG_SYS_MAX_FLASH_SECT 128
-#else
-/* use CFI flash driver */
-#define CONFIG_SYS_FLASH_CFI 1 /* Flash is CFI conformant */
-#define CONFIG_FLASH_CFI_DRIVER 1 /* Use the common driver */
-#define CONFIG_FLASH_CFI_MTD /* with MTD support */
-#define CONFIG_SYS_FLASH_BANKS_LIST { CONFIG_SYS_BOOTCS_START }
-#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max num of flash banks
- (= chip selects) */
-#define CONFIG_SYS_MAX_FLASH_SECT 512 /* max num of sects on one chip */
-#endif
-
-#define CONFIG_SYS_FLASH_EMPTY_INFO
-#define CONFIG_SYS_FLASH_SIZE 0x04000000 /* 64 MByte */
-#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE 1
-
-#if defined (CONFIG_CAM5200)
-# define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + 0x00040000)
-#elif defined(CONFIG_TQM5200_B)
-# define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + 0x00080000)
-#else
-# define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + 0x00060000)
-#endif
-
-/* Dynamic MTD partition support */
-#define CONFIG_CMD_MTDPARTS
-#define CONFIG_MTD_DEVICE /* needed for mtdparts commands */
-#define MTDIDS_DEFAULT "nor0=fc000000.flash"
-
-#if defined(CONFIG_STK52XX)
-# if defined(CONFIG_TQM5200_B)
-# if defined(CONFIG_SYS_LOWBOOT)
-# define MTDPARTS_DEFAULT "mtdparts=fc000000.flash:1m(firmware)," \
- "256k(dtb)," \
- "2304k(kernel)," \
- "2560k(small-fs)," \
- "2m(initrd)," \
- "8m(misc)," \
- "16m(big-fs)"
-# else /* highboot */
-# define MTDPARTS_DEFAULT "mtdparts=fc000000.flash:2560k(kernel),"\
- "3584k(small-fs)," \
- "2m(initrd)," \
- "8m(misc)," \
- "15m(big-fs)," \
- "1m(firmware)"
-# endif /* CONFIG_SYS_LOWBOOT */
-# else /* !CONFIG_TQM5200_B */
-# define MTDPARTS_DEFAULT "mtdparts=fc000000.flash:640k(firmware),"\
- "128k(dtb)," \
- "2304k(kernel)," \
- "2m(initrd)," \
- "4m(small-fs)," \
- "8m(misc)," \
- "15m(big-fs)"
-# endif /* CONFIG_TQM5200_B */
-#elif defined (CONFIG_CAM5200)
-# define MTDPARTS_DEFAULT "mtdparts=fc000000.flash:768k(firmware),"\
- "1792k(kernel)," \
- "5632k(rootfs)," \
- "24m(home)"
-#elif defined (CONFIG_CHARON)
-# define MTDPARTS_DEFAULT "mtdparts=fc000000.flash:640k(firmware),"\
- "1408k(kernel)," \
- "2m(initrd)," \
- "4m(small-fs)," \
- "24320k(big-fs)," \
- "256k(dts)"
-#elif defined (CONFIG_FO300)
-# define MTDPARTS_DEFAULT "mtdparts=fc000000.flash:640k(firmware),"\
- "1408k(kernel)," \
- "2m(initrd)," \
- "4m(small-fs)," \
- "8m(misc)," \
- "16m(big-fs)"
-#else
-# error "Unknown Carrier Board"
-#endif /* CONFIG_STK52XX */
-
-/*
- * Environment settings
- */
-#define CONFIG_ENV_IS_IN_FLASH 1
-#define CONFIG_ENV_SIZE 0x4000 /* 16 k - keep small for fast booting */
-#if defined(CONFIG_TQM5200_B) || defined (CONFIG_CAM5200)
-#define CONFIG_ENV_SECT_SIZE 0x40000
-#else
-#define CONFIG_ENV_SECT_SIZE 0x20000
-#endif /* CONFIG_TQM5200_B */
-#define CONFIG_ENV_ADDR_REDUND (CONFIG_ENV_ADDR + CONFIG_ENV_SECT_SIZE)
-#define CONFIG_ENV_SIZE_REDUND (CONFIG_ENV_SIZE)
-
-/*
- * Memory map
- */
-#define CONFIG_SYS_MBAR 0xF0000000
-#define CONFIG_SYS_SDRAM_BASE 0x00000000
-#define CONFIG_SYS_DEFAULT_MBAR 0x80000000
-
-/* Use ON-Chip SRAM until RAM will be available */
-#define CONFIG_SYS_INIT_RAM_ADDR MPC5XXX_SRAM
-#ifdef CONFIG_POST
-/* preserve space for the post_word at end of on-chip SRAM */
-#define CONFIG_SYS_INIT_RAM_SIZE MPC5XXX_SRAM_POST_SIZE
-#else
-#define CONFIG_SYS_INIT_RAM_SIZE MPC5XXX_SRAM_SIZE
-#endif
-
-
-#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
-#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
-
-#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE
-#if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE)
-# define CONFIG_SYS_RAMBOOT 1
-#endif
-
-#if defined (CONFIG_CAM5200)
-# define CONFIG_SYS_MONITOR_LEN (256 << 10) /* Reserve 256 kB for Monitor */
-#elif defined(CONFIG_TQM5200_B)
-# define CONFIG_SYS_MONITOR_LEN (512 << 10) /* Reserve 512 kB for Monitor */
-#else
-# define CONFIG_SYS_MONITOR_LEN (384 << 10) /* Reserve 384 kB for Monitor */
-#endif
-
-#define CONFIG_SYS_MALLOC_LEN (1024 << 10) /* Reserve 1024 kB for malloc() */
-#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
-
-/*
- * Ethernet configuration
- */
-#define CONFIG_MPC5xxx_FEC 1
-#define CONFIG_MPC5xxx_FEC_MII100
-/*
- * Define CONFIG_MPC5xxx_FEC_MII10 to force FEC at 10Mb
- */
-/* #define CONFIG_MPC5xxx_FEC_MII10 */
-#define CONFIG_PHY_ADDR 0x00
-
-/*
- * GPIO configuration
- *
- * use CS1: Bit 0 (mask: 0x80000000):
- * 1 -> Pin gpio_wkup_6 as second SDRAM chip select (mem_cs1).
- * use ALT CAN position: Bits 2-3 (mask: 0x30000000):
- * 00 -> No Alternatives, CAN1/2 on PSC2 according to PSC2 setting.
- * SPI on PSC3 according to PSC3 setting. Use for CAM5200.
- * 01 -> CAN1 on I2C1, CAN2 on Tmr0/1.
- * Use for REV200 STK52XX boards and FO300 boards. Do not use
- * with REV100 modules (because, there I2C1 is used as I2C bus).
- * use ATA: Bits 6-7 (mask 0x03000000):
- * 00 -> No ATA chip selects, csb_4/5 used as normal chip selects.
- * Use for CAM5200 board.
- * 01 -> ATA cs0/1 on csb_4/5. Use for the remaining boards.
- * use PSC6: Bits 9-11 (mask 0x00700000):
- * 000 -> use PSC6_0 to PSC6_3 as GPIO, PSC6 could not be used as
- * UART, CODEC or IrDA.
- * GPIO on PSC6_3 is used in post_hotkeys_pressed() to
- * enable extended POST tests.
- * Use for MINI-FAP and TQM5200_IB boards.
- * 101 -> use PSC6 as UART. Pins PSC6_0 to PSC6_3 are used.
- * Extended POST test is not available.
- * Use for STK52xx, FO300 and CAM5200 boards.
- * WARNING: When the extended POST is enabled, these bits will
- * be overridden by this code as GPIOs!
- * use PCI_DIS: Bit 16 (mask 0x00008000):
- * 1 -> disable PCI controller (on CAM5200 board).
- * use USB: Bits 18-19 (mask 0x00003000):
- * 10 -> two UARTs (on FO300 and CAM5200).
- * use PSC3: Bits 20-23 (mask: 0x00000f00):
- * 0000 -> All PSC3 pins are GPIOs.
- * 1100 -> UART/SPI (on FO300 board).
- * 0100 -> UART (on CAM5200 board).
- * use PSC2: Bits 25:27 (mask: 0x00000030):
- * 000 -> All PSC2 pins are GPIOs.
- * 100 -> UART (on CAM5200 board).
- * 001 -> CAN1/2 on PSC2 pins.
- * Use for REV100 STK52xx boards
- * 01x -> Use AC97 (on FO300 board).
- * use PSC1: Bits 29-31 (mask: 0x00000007):
- * 100 -> UART (on all boards).
- */
-#if !defined(CONFIG_SYS_GPS_PORT_CONFIG)
-#if defined (CONFIG_MINIFAP)
-# define CONFIG_SYS_GPS_PORT_CONFIG 0x91000004
-#elif defined (CONFIG_STK52XX)
-# if defined (CONFIG_STK52XX_REV100)
-# define CONFIG_SYS_GPS_PORT_CONFIG 0x81500014
-# else /* STK52xx REV200 and above */
-# if defined (CONFIG_TQM5200_REV100)
-# error TQM5200 REV100 not supported on STK52XX REV200 or above
-# else/* TQM5200 REV200 and above */
-# define CONFIG_SYS_GPS_PORT_CONFIG 0x91500404
-# endif
-# endif
-#elif defined (CONFIG_FO300)
-# define CONFIG_SYS_GPS_PORT_CONFIG 0x91502c24
-#elif defined (CONFIG_CAM5200)
-# define CONFIG_SYS_GPS_PORT_CONFIG 0x8050A444
-#else /* TMQ5200 Inbetriebnahme-Board */
-# define CONFIG_SYS_GPS_PORT_CONFIG 0x81000004
-#endif
-#endif
-
-/*
- * RTC configuration
- */
-#if defined (CONFIG_STK52XX) && !defined (CONFIG_STK52XX_REV100)
-# define CONFIG_RTC_M41T11 1
-# define CONFIG_SYS_I2C_RTC_ADDR 0x68
-# define CONFIG_SYS_M41T11_BASE_YEAR 1900 /* because Linux uses the same base
- year */
-#else
-# define CONFIG_RTC_MPC5200 1 /* use internal MPC5200 RTC */
-#endif
-
-/*
- * Miscellaneous configurable options
- */
-#define CONFIG_SYS_LONGHELP /* undef to save memory */
-
-#define CONFIG_CMDLINE_EDITING 1 /* add command line history */
-
-#define CONFIG_SYS_CACHELINE_SIZE 32 /* For MPC5xxx CPUs */
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_SYS_CACHELINE_SHIFT 5 /* log base 2 of the above value */
-#endif
-
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
-#else
-#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
-#endif
-#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
-#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
-#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
-
-/* Enable an alternate, more extensive memory test */
-#define CONFIG_SYS_ALT_MEMTEST
-
-#define CONFIG_SYS_MEMTEST_START 0x00100000 /* memtest works on */
-#define CONFIG_SYS_MEMTEST_END 0x00f00000 /* 1 ... 15 MB in DRAM */
-
-#define CONFIG_SYS_LOAD_ADDR 0x100000 /* default load address */
-
-/*
- * Various low-level settings
- */
-#define CONFIG_SYS_HID0_INIT HID0_ICE | HID0_ICFI
-#define CONFIG_SYS_HID0_FINAL HID0_ICE
-
-#define CONFIG_SYS_BOOTCS_START CONFIG_SYS_FLASH_BASE
-#define CONFIG_SYS_BOOTCS_SIZE CONFIG_SYS_FLASH_SIZE
-#ifdef CONFIG_SYS_PCICLK_EQUALS_IPBCLK_DIV2
-#define CONFIG_SYS_BOOTCS_CFG 0x0008DF30 /* for pci_clk = 66 MHz */
-#else
-#define CONFIG_SYS_BOOTCS_CFG 0x0004DF30 /* for pci_clk = 33 MHz */
-#endif
-#define CONFIG_SYS_CS0_START CONFIG_SYS_FLASH_BASE
-#define CONFIG_SYS_CS0_SIZE CONFIG_SYS_FLASH_SIZE
-
-#define CONFIG_LAST_STAGE_INIT
-
-/*
- * SRAM - Do not map below 2 GB in address space, because this area is used
- * for SDRAM autosizing.
- */
-#define CONFIG_SYS_CS2_START 0xE5000000
-#define CONFIG_SYS_CS2_SIZE 0x100000 /* 1 MByte */
-#define CONFIG_SYS_CS2_CFG 0x0004D930
-
-/*
- * Grafic controller - Do not map below 2 GB in address space, because this
- * area is used for SDRAM autosizing.
- */
-#define SM501_FB_BASE 0xE0000000
-#define CONFIG_SYS_CS1_START (SM501_FB_BASE)
-#define CONFIG_SYS_CS1_SIZE 0x4000000 /* 64 MByte */
-#define CONFIG_SYS_CS1_CFG 0x8F48FF70
-#define SM501_MMIO_BASE CONFIG_SYS_CS1_START + 0x03E00000
-
-#define CONFIG_SYS_CS_BURST 0x00000000
-#define CONFIG_SYS_CS_DEADCYCLE 0x33333311 /* 1 dead cycle for flash and SM501 */
-
-#if defined(CONFIG_CAM5200)
-#define CONFIG_SYS_CS4_START 0xB0000000
-#define CONFIG_SYS_CS4_SIZE 0x00010000
-#define CONFIG_SYS_CS4_CFG 0x01019C10
-
-#define CONFIG_SYS_CS5_START 0xD0000000
-#define CONFIG_SYS_CS5_SIZE 0x01208000
-#define CONFIG_SYS_CS5_CFG 0x1414BF10
-#endif
-
-#define CONFIG_SYS_RESET_ADDRESS 0xff000000
-
-/*-----------------------------------------------------------------------
- * USB stuff
- *-----------------------------------------------------------------------
- */
-#define CONFIG_USB_CLOCK 0x0001BBBB
-#define CONFIG_USB_CONFIG 0x00001000
-
-/*-----------------------------------------------------------------------
- * IDE/ATA stuff Supports IDE harddisk
- *-----------------------------------------------------------------------
- */
-
-#undef CONFIG_IDE_8xx_PCCARD /* Use IDE with PC Card Adapter */
-
-#undef CONFIG_IDE_8xx_DIRECT /* Direct IDE not supported */
-#undef CONFIG_IDE_LED /* LED for ide not supported */
-
-#define CONFIG_IDE_RESET /* reset for ide supported */
-#define CONFIG_IDE_PREINIT
-
-#define CONFIG_SYS_IDE_MAXBUS 1 /* max. 1 IDE bus */
-#define CONFIG_SYS_IDE_MAXDEVICE 2 /* max. 2 drives per IDE bus */
-
-#define CONFIG_SYS_ATA_IDE0_OFFSET 0x0000
-
-#define CONFIG_SYS_ATA_BASE_ADDR MPC5XXX_ATA
-
-/* Offset for data I/O */
-#define CONFIG_SYS_ATA_DATA_OFFSET (0x0060)
-
-/* Offset for normal register accesses */
-#define CONFIG_SYS_ATA_REG_OFFSET (CONFIG_SYS_ATA_DATA_OFFSET)
-
-/* Offset for alternate registers */
-#define CONFIG_SYS_ATA_ALT_OFFSET (0x005C)
-
-/* Interval between registers */
-#define CONFIG_SYS_ATA_STRIDE 4
-
-/* Support ATAPI devices */
-#define CONFIG_ATAPI 1
-
-/*-----------------------------------------------------------------------
- * Open firmware flat tree support
- *-----------------------------------------------------------------------
- */
-#define OF_CPU "PowerPC,5200@0"
-#define OF_SOC "soc5200@f0000000"
-#define OF_TBCLK (bd->bi_busfreq / 4)
-#define OF_STDOUT_PATH "/soc5200@f0000000/serial@2000"
-
-#endif /* __CONFIG_H */
projects / platform / kernel / u-boot.git / blobdiff