Convert CONFIG_MISC_INIT_R to Kconfig

[platform/kernel/u-boot.git] / include / configs / T1040QDS.h

diff --git a/include/configs/T1040QDS.h b/include/configs/T1040QDS.h
index bf2c15a..e890860 100644 (file)
--- a/include/configs/T1040QDS.h
+++ b/include/configs/T1040QDS.h
@@ -36,15 +36,10 @@
 
 /* High Level Configuration Options */
 #define CONFIG_SYS_BOOK3E_HV           /* Category E.HV supported */
-#define CONFIG_MP                      /* support multiple processors */
 
 /* support deep sleep */
 #define CONFIG_DEEP_SLEEP
 
-#ifndef CONFIG_SYS_TEXT_BASE
-#define CONFIG_SYS_TEXT_BASE   0xeff40000
-#endif
-
 #ifndef CONFIG_RESET_VECTOR_ADDRESS
 #define CONFIG_RESET_VECTOR_ADDRESS    0xeffffffc
 #endif
@@ -126,8 +121,6 @@ unsigned long get_board_ddr_clk(void);
 
 #define CONFIG_SYS_MEMTEST_START       0x00200000      /* memtest works on */
 #define CONFIG_SYS_MEMTEST_END         0x00400000
-#define CONFIG_SYS_ALT_MEMTEST
-#define CONFIG_PANIC_HANG      /* do not reset board on panic */
 
 /*
  *  Config the L3 Cache as L3 SRAM
@@ -283,7 +276,6 @@ unsigned long get_board_ddr_clk(void);
 #define CONFIG_SYS_NAND_DDR_LAW                11
 #define CONFIG_SYS_NAND_BASE_LIST      { CONFIG_SYS_NAND_BASE }
 #define CONFIG_SYS_MAX_NAND_DEVICE     1
-#define CONFIG_CMD_NAND
 
 #define CONFIG_SYS_NAND_BLOCK_SIZE     (128 * 1024)
 
@@ -345,9 +337,6 @@ unsigned long get_board_ddr_clk(void);
 #define CONFIG_SYS_RAMBOOT
 #endif
 
-#define CONFIG_BOARD_EARLY_INIT_R
-#define CONFIG_MISC_INIT_R
-
 #define CONFIG_HWCONFIG
 
 /* define to use L1 as initial stack */
@@ -373,7 +362,6 @@ unsigned long get_board_ddr_clk(void);
  * open - index 2
  * shorted - index 1
  */
-#define CONFIG_CONS_INDEX      1
 #define CONFIG_SYS_NS16550_SERIAL
 #define CONFIG_SYS_NS16550_REG_SIZE    1
 #define CONFIG_SYS_NS16550_CLK         (get_bus_freq(0)/2)
@@ -501,9 +489,6 @@ unsigned long get_board_ddr_clk(void);
 /* SATA */
 #define CONFIG_FSL_SATA_V2
 #ifdef CONFIG_FSL_SATA_V2
-#define CONFIG_LIBATA
-#define CONFIG_FSL_SATA
-
 #define CONFIG_SYS_SATA_MAX_DEVICE     2
 #define CONFIG_SATA1
 #define CONFIG_SYS_SATA1               CONFIG_SYS_MPC85xx_SATA1_ADDR
@@ -528,7 +513,6 @@ unsigned long get_board_ddr_clk(void);
 #endif
 
 #ifdef CONFIG_MMC
-#define CONFIG_FSL_ESDHC
 #define CONFIG_FSL_ESDHC_USE_PERIPHERAL_CLK
 #define CONFIG_SYS_FSL_ESDHC_ADDR       CONFIG_SYS_MPC85xx_ESDHC_ADDR
 #define CONFIG_FSL_ESDHC_ADAPTER_IDENT
@@ -536,7 +520,6 @@ unsigned long get_board_ddr_clk(void);
 
 /* Qman/Bman */
 #ifndef CONFIG_NOBQFMAN
-#define CONFIG_SYS_DPAA_QBMAN          /* Support Q/Bman */
 #define CONFIG_SYS_BMAN_NUM_PORTALS    10
 #define CONFIG_SYS_BMAN_MEM_BASE       0xf4000000
 #define CONFIG_SYS_BMAN_MEM_PHYS       0xff4000000ull
@@ -616,9 +599,7 @@ unsigned long get_board_ddr_clk(void);
 #define CONFIG_SYS_FM1_DTSEC3_RISER_PHY_ADDR    0x1e
 #define CONFIG_SYS_FM1_DTSEC4_RISER_PHY_ADDR    0x1f
 
-#define CONFIG_MII             /* MII PHY management */
 #define CONFIG_ETHPRIME                "FM1@DTSEC1"
-#define CONFIG_PHY_GIGE                /* Include GbE speed/duplex detection */
 #endif
 
 /* Enable VSC9953 L2 Switch driver */
@@ -630,16 +611,7 @@ unsigned long get_board_ddr_clk(void);
  * Dynamic MTD Partition support with mtdparts
  */
 #ifdef CONFIG_MTD_NOR_FLASH
-#define CONFIG_MTD_DEVICE
-#define CONFIG_MTD_PARTITIONS
 #define CONFIG_FLASH_CFI_MTD
-#define MTDIDS_DEFAULT "nor0=fe8000000.nor,nand0=fff800000.flash," \
-                       "spi0=spife110000.0"
-#define MTDPARTS_DEFAULT       "mtdparts=fe8000000.nor:1m(uboot),5m(kernel)," \
-                               "128k(dtb),96m(fs),-(user);"\
-                               "fff800000.flash:2m(uboot),9m(kernel),"\
-                               "128k(dtb),96m(fs),-(user);spife110000.0:" \
-                               "2m(uboot),9m(kernel),128k(dtb),-(user)"
 #endif
 
 /*
@@ -649,29 +621,9 @@ unsigned long get_board_ddr_clk(void);
 #define CONFIG_SYS_LOADS_BAUD_CHANGE   /* allow baudrate change */
 
 /*
- * Command line configuration.
- */
-#define CONFIG_CMD_REGINFO
-
-#ifdef CONFIG_PCI
-#define CONFIG_CMD_PCI
-#endif
-
-/*
  * Miscellaneous configurable options
  */
-#define CONFIG_SYS_LONGHELP                    /* undef to save memory */
-#define CONFIG_CMDLINE_EDITING                 /* Command-line editing */
-#define CONFIG_AUTO_COMPLETE                   /* add autocompletion support */
 #define CONFIG_SYS_LOAD_ADDR   0x2000000       /* default load address */
-#ifdef CONFIG_CMD_KGDB
-#define CONFIG_SYS_CBSIZE      1024            /* Console I/O Buffer Size */
-#else
-#define CONFIG_SYS_CBSIZE      256             /* Console I/O Buffer Size */
-#endif
-#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16)
-#define CONFIG_SYS_MAXARGS     16              /* max number of command args */
-#define CONFIG_SYS_BARGSIZE    CONFIG_SYS_CBSIZE/* Boot Argument Buffer Size */
 
 /*
  * For booting Linux, the board info and command line data