+++ /dev/null
-/*
- * (C) Copyright 2001
- * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-/*
- * board/config.h - configuration options, board specific
- */
-
-#ifndef __CONFIG_H
-#define __CONFIG_H
-
-/***********************************************************
- * High Level Configuration Options
- * (easy to change)
- ***********************************************************/
-#define CONFIG_405GP 1 /* This is a PPC405 CPU */
-#define CONFIG_PIP405 1 /* ...on a PIP405 board */
-
-#define CONFIG_SYS_TEXT_BASE 0xFFF80000
-
-/***********************************************************
- * Clock
- ***********************************************************/
-#define CONFIG_SYS_CLK_FREQ 33000000 /* external frequency to pll */
-
-/*
- * BOOTP options
- */
-#define CONFIG_BOOTP_BOOTFILESIZE
-#define CONFIG_BOOTP_BOOTPATH
-#define CONFIG_BOOTP_GATEWAY
-#define CONFIG_BOOTP_HOSTNAME
-
-/*
- * Command line configuration.
- */
-#define CONFIG_CMD_IDE
-#define CONFIG_CMD_PCI
-#define CONFIG_CMD_IRQ
-#define CONFIG_CMD_EEPROM
-#define CONFIG_CMD_REGINFO
-#define CONFIG_CMD_FDC
-#define CONFIG_SCSI
-#define CONFIG_CMD_DATE
-#define CONFIG_CMD_SDRAM
-#define CONFIG_CMD_SAVES
-#define CONFIG_CMD_BSP
-
-/**************************************************************
- * I2C Stuff:
- * the PIP405 is equiped with an Atmel 24C128/256 EEPROM at address
- * 0x53.
- * Caution: on the same bus is the SPD (Serial Presens Detect
- * EEPROM of the SDRAM
- * The Atmel EEPROM uses 16Bit addressing.
- ***************************************************************/
-#define CONFIG_SYS_I2C
-#define CONFIG_SYS_I2C_PPC4XX
-#define CONFIG_SYS_I2C_PPC4XX_CH0
-#define CONFIG_SYS_I2C_PPC4XX_SPEED_0 50000
-#define CONFIG_SYS_I2C_PPC4XX_SLAVE_0 0x7F
-
-#define CONFIG_SYS_I2C_EEPROM_ADDR 0x53
-#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2
-#define CONFIG_ENV_IS_IN_EEPROM 1 /* use EEPROM for environment vars */
-#define CONFIG_ENV_OFFSET 0x000 /* environment starts at the beginning of the EEPROM */
-#define CONFIG_ENV_SIZE 0x800 /* 2 kBytes may be used for env vars */
-
-#undef CONFIG_SYS_I2C_EEPROM_ADDR_OVERFLOW
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 6 /* The Atmel 24C128/256 has */
- /* 64 byte page write mode using*/
- /* last 6 bits of the address */
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 10 /* and takes up to 10 msec */
-
-/***************************************************************
- * Definitions for Serial Presence Detect EEPROM address
- * (to get SDRAM settings)
- ***************************************************************/
-#define SPD_EEPROM_ADDRESS 0x50
-
-#define CONFIG_BOARD_EARLY_INIT_F
-#define CONFIG_BOARD_EARLY_INIT_R
-
-/**************************************************************
- * Environment definitions
- **************************************************************/
-#define CONFIG_BAUDRATE 9600 /* STD Baudrate */
-
-/* autoboot (do NOT change this set environment variable "bootdelay" to -1 instead) */
-/* #define CONFIG_BOOT_RETRY_TIME -10 /XXX* feature is available but not enabled */
-
-#define CONFIG_BOOTCOMMAND "diskboot 400000 0:1; bootm" /* autoboot command */
-#define CONFIG_BOOTARGS "console=ttyS0,9600 root=/dev/hda5" /* boot arguments */
-
-#define CONFIG_IPADDR 10.0.0.100
-#define CONFIG_SERVERIP 10.0.0.1
-#define CONFIG_PREBOOT
-/***************************************************************
- * defines if the console is stored in the environment
- ***************************************************************/
-#define CONFIG_SYS_CONSOLE_IS_IN_ENV /* stdin, stdout and stderr are in evironment */
-/***************************************************************
- * defines if an overwrite_console function exists
- *************************************************************/
-#define CONFIG_SYS_CONSOLE_OVERWRITE_ROUTINE
-#define CONFIG_SYS_CONSOLE_INFO_QUIET
-/***************************************************************
- * defines if the overwrite_console should be stored in the
- * environment
- **************************************************************/
-#undef CONFIG_SYS_CONSOLE_ENV_OVERWRITE
-
-/**************************************************************
- * loads config
- *************************************************************/
-#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
-#define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
-
-#define CONFIG_MISC_INIT_R
-/***********************************************************
- * Miscellaneous configurable options
- **********************************************************/
-#define CONFIG_SYS_LONGHELP /* undef to save memory */
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
-#else
-#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
-#endif
-#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
-#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
-#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
-
-#define CONFIG_SYS_MEMTEST_START 0x0100000 /* memtest works on */
-#define CONFIG_SYS_MEMTEST_END 0x0C00000 /* 1 ... 12 MB in DRAM */
-
-#define CONFIG_CONS_INDEX 1 /* Use UART0 */
-#define CONFIG_SYS_NS16550_SERIAL
-#define CONFIG_SYS_NS16550_REG_SIZE 1
-#define CONFIG_SYS_NS16550_CLK get_serial_clock()
-
-#undef CONFIG_SYS_EXT_SERIAL_CLOCK /* no external serial clock used */
-#define CONFIG_SYS_BASE_BAUD 691200
-
-/* The following table includes the supported baudrates */
-#define CONFIG_SYS_BAUDRATE_TABLE \
- { 300, 600, 1200, 2400, 4800, 9600, 19200, 38400, \
- 57600, 115200, 230400, 460800, 921600 }
-
-#define CONFIG_SYS_LOAD_ADDR 0x400000 /* default load address */
-#define CONFIG_SYS_EXTBDINFO 1 /* To use extended board_into (bd_t) */
-
-/*-----------------------------------------------------------------------
- * PCI stuff
- *-----------------------------------------------------------------------
- */
-#define PCI_HOST_ADAPTER 0 /* configure ar pci adapter */
-#define PCI_HOST_FORCE 1 /* configure as pci host */
-#define PCI_HOST_AUTO 2 /* detected via arbiter enable */
-
-#define CONFIG_PCI /* include pci support */
-#define CONFIG_PCI_INDIRECT_BRIDGE /* indirect PCI bridge support */
-#define CONFIG_PCI_HOST PCI_HOST_FORCE /* configure as pci-host */
-#define CONFIG_PCI_PNP /* pci plug-and-play */
- /* resource configuration */
-#define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x0000 /* PCI Vendor ID: to-do!!! */
-#define CONFIG_SYS_PCI_SUBSYS_DEVICEID 0x0000 /* PCI Device ID: to-do!!! */
-#define CONFIG_SYS_PCI_PTM1LA 0x00000000 /* point to sdram */
-#define CONFIG_SYS_PCI_PTM1MS 0x80000001 /* 2GB, enable hard-wired to 1 */
-#define CONFIG_SYS_PCI_PTM1PCI 0x00000000 /* Host: use this pci address */
-#define CONFIG_SYS_PCI_PTM2LA 0x00000000 /* disabled */
-#define CONFIG_SYS_PCI_PTM2MS 0x00000000 /* disabled */
-#define CONFIG_SYS_PCI_PTM2PCI 0x00000000 /* Host: use this pci address */
-
-/*-----------------------------------------------------------------------
- * Start addresses for the final memory configuration
- * (Set up by the startup code)
- * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0
- */
-#define CONFIG_SYS_SDRAM_BASE 0x00000000
-#define CONFIG_SYS_FLASH_BASE 0xFFF80000
-#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_FLASH_BASE
-#define CONFIG_SYS_MONITOR_LEN (512 * 1024) /* Reserve 512 kB for Monitor */
-#define CONFIG_SYS_MALLOC_LEN (1024 * 1024) /* Reserve 1024 kB for malloc() */
-
-/*
- * For booting Linux, the board info and command line data
- * have to be in the first 8 MB of memory, since this is
- * the maximum mapped by the Linux kernel during initialization.
- */
-#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
-/*-----------------------------------------------------------------------
- * FLASH organization
- */
-#define CONFIG_SYS_UPDATE_FLASH_SIZE
-#define CONFIG_SYS_FLASH_PROTECTION
-#define CONFIG_SYS_FLASH_EMPTY_INFO
-
-#define CONFIG_SYS_FLASH_CFI
-#define CONFIG_FLASH_CFI_DRIVER
-
-#define CONFIG_FLASH_SHOW_PROGRESS 45
-
-#define CONFIG_SYS_MAX_FLASH_BANKS 1
-#define CONFIG_SYS_MAX_FLASH_SECT 256
-
-/*
- * Init Memory Controller:
- */
-#define FLASH_MAX_SIZE 0x00800000 /* 8MByte max */
-#define FLASH_BASE_PRELIM 0xFF800000 /* open the flash CS */
-/* Size: 0=1MB, 1=2MB, 2=4MB, 3=8MB, 4=16MB, 5=32MB, 6=64MB, 7=128MB */
-#define FLASH_SIZE_PRELIM 3 /* maximal flash FLASH size bank #0 */
-
-#define CONFIG_BOARD_EARLY_INIT_F
-
-/* Configuration Port location */
-#define CONFIG_PORT_ADDR 0xF4000000
-#define MULTI_PURPOSE_SOCKET_ADDR 0xF8000000
-
-/*-----------------------------------------------------------------------
- * Definitions for initial stack pointer and data area (in On Chip SRAM)
- */
-#define CONFIG_SYS_TEMP_STACK_OCM 1
-#define CONFIG_SYS_OCM_DATA_ADDR 0xF0000000
-#define CONFIG_SYS_OCM_DATA_SIZE 0x1000
-#define CONFIG_SYS_INIT_RAM_ADDR CONFIG_SYS_OCM_DATA_ADDR /* inside of On Chip SRAM */
-#define CONFIG_SYS_INIT_RAM_SIZE CONFIG_SYS_OCM_DATA_SIZE /* Size of On Chip SRAM */
-#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
-#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
-
-/***********************************************************************
- * External peripheral base address
- ***********************************************************************/
-#define CONFIG_SYS_ISA_IO_BASE_ADDRESS 0xE8000000
-
-/***********************************************************************
- * Last Stage Init
- ***********************************************************************/
-#define CONFIG_LAST_STAGE_INIT
-/************************************************************
- * Ethernet Stuff
- ***********************************************************/
-#define CONFIG_PPC4xx_EMAC
-#define CONFIG_MII 1 /* MII PHY management */
-#define CONFIG_PHY_ADDR 1 /* PHY address */
-/************************************************************
- * RTC
- ***********************************************************/
-#define CONFIG_RTC_MC146818
-#undef CONFIG_WATCHDOG /* watchdog disabled */
-
-/************************************************************
- * IDE/ATA stuff
- ************************************************************/
-#define CONFIG_SYS_IDE_MAXBUS 2 /* max. 2 IDE busses */
-#define CONFIG_SYS_IDE_MAXDEVICE (CONFIG_SYS_IDE_MAXBUS*2) /* max. 2 drives per IDE bus */
-
-#define CONFIG_SYS_ATA_BASE_ADDR CONFIG_SYS_ISA_IO_BASE_ADDRESS /* base address */
-#define CONFIG_SYS_ATA_IDE0_OFFSET 0x01F0 /* ide0 offste */
-#define CONFIG_SYS_ATA_IDE1_OFFSET 0x0170 /* ide1 offset */
-#define CONFIG_SYS_ATA_DATA_OFFSET 0 /* data reg offset */
-#define CONFIG_SYS_ATA_REG_OFFSET 0 /* reg offset */
-#define CONFIG_SYS_ATA_ALT_OFFSET 0x200 /* alternate register offset */
-
-#undef CONFIG_IDE_8xx_DIRECT /* no pcmcia interface required */
-#undef CONFIG_IDE_LED /* no led for ide supported */
-#define CONFIG_IDE_RESET /* reset for ide supported... */
-#define CONFIG_IDE_RESET_ROUTINE /* with a special reset function */
-#define CONFIG_SUPPORT_VFAT
-
-/************************************************************
- * ATAPI support (experimental)
- ************************************************************/
-#define CONFIG_ATAPI /* enable ATAPI Support */
-
-/************************************************************
- * SCSI support (experimental) only SYM53C8xx supported
- ************************************************************/
-#define CONFIG_SCSI_SYM53C8XX
-#define CONFIG_SYS_SCSI_MAX_LUN 8 /* number of supported LUNs */
-#define CONFIG_SYS_SCSI_MAX_SCSI_ID 7 /* maximum SCSI ID (0..6) */
-#define CONFIG_SYS_SCSI_MAX_DEVICE CONFIG_SYS_SCSI_MAX_SCSI_ID * CONFIG_SYS_SCSI_MAX_LUN /* maximum Target devices */
-#define CONFIG_SYS_SCSI_SPIN_UP_TIME 2
-
-/************************************************************
- * Disk-On-Chip configuration
- ************************************************************/
-#define CONFIG_SYS_MAX_DOC_DEVICE 1 /* Max number of DOC devices */
-#define CONFIG_SYS_DOC_SHORT_TIMEOUT
-#define CONFIG_SYS_DOC_SUPPORT_2000
-#define CONFIG_SYS_DOC_SUPPORT_MILLENNIUM
-
-/************************************************************
- * DISK Partition support
- ************************************************************/
-#define CONFIG_DOS_PARTITION
-#define CONFIG_MAC_PARTITION
-#define CONFIG_ISO_PARTITION /* Experimental */
-
-/************************************************************
- * Video support
- ************************************************************/
-#define CONFIG_VIDEO /*To enable video controller support */
-#define CONFIG_VIDEO_CT69000
-#define CONFIG_CFB_CONSOLE
-#define CONFIG_VIDEO_LOGO
-#define CONFIG_CONSOLE_EXTRA_INFO
-#define CONFIG_VGA_AS_SINGLE_DEVICE
-#define CONFIG_VIDEO_SW_CURSOR
-#define CONFIG_VIDEO_ONBOARD /* Video controller is on-board */
-
-/************************************************************
- * USB support
- ************************************************************/
-#define CONFIG_USB_UHCI
-#define CONFIG_USB_KEYBOARD
-#define CONFIG_USB_STORAGE
-
-/* Enable needed helper functions */
-#define CONFIG_SYS_STDIO_DEREGISTER /* needs stdio_deregister */
-
-/************************************************************
- * Debug support
- ************************************************************/
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */
-#endif
-
-/************************************************************
- * support BZIP2 compression
- ************************************************************/
-#define CONFIG_BZIP2 1
-
-/************************************************************
- * Ident
- ************************************************************/
-#define VERSION_TAG "released"
-#define CONFIG_ISO_STRING "MEV-10066-001"
-#define CONFIG_IDENT_STRING "\n(c) 2002 by MPL AG Switzerland, " CONFIG_ISO_STRING " " VERSION_TAG
-
-#endif /* __CONFIG_H */
projects / platform / kernel / u-boot.git / blobdiff