+++ /dev/null
-/*
- * (C) Copyright 2001
- * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-
-#ifndef __CONFIG_H
-#define __CONFIG_H
-
-#define MV_VERSION "v0.2.0"
-
-/* LED0 = Power , LED1 = Error , LED2-5 = error code, LED6-7=00 -->PPCBoot error */
-#define ERR_NONE 0
-#define ERR_ENV 1
-#define ERR_BOOTM_BADMAGIC 2
-#define ERR_BOOTM_BADCRC 3
-#define ERR_BOOTM_GUNZIP 4
-#define ERR_BOOTP_TIMEOUT 5
-#define ERR_DHCP 6
-#define ERR_TFTP 7
-#define ERR_NOLAN 8
-#define ERR_LANDRV 9
-
-#define CONFIG_BOARD_TYPES 1
-#define MVBLUE_BOARD_BOX 1
-#define MVBLUE_BOARD_LYNX 2
-
-#define CONFIG_SYS_TEXT_BASE 0xFFF00000
-#define CONFIG_SYS_LDSCRIPT "board/mvblue/u-boot.lds"
-
-#if 0
-#define ERR_LED(code) do { if (code) \
- *(volatile char *)(0xff000003) = ( 3 | (code<<4) ) & 0xf3; \
- else \
- *(volatile char *)(0xff000003) = ( 1 ); \
-} while(0)
-#else
-#define ERR_LED(code)
-#endif
-
-#define CONFIG_MPC824X 1
-#define CONFIG_MPC8245 1
-#define CONFIG_MVBLUE 1
-
-#define CONFIG_CLOCKS_IN_MHZ 1
-
-#define CONFIG_BOARD_TYPES 1
-
-#define CONFIG_CONS_INDEX 1
-#define CONFIG_BAUDRATE 115200
-
-#define CONFIG_BOOTDELAY 3
-#define CONFIG_BOOT_RETRY_TIME -1
-
-#define CONFIG_AUTOBOOT_KEYED
-#define CONFIG_AUTOBOOT_PROMPT \
- "autoboot in %d seconds (stop with 's')...\n", bootdelay
-#define CONFIG_AUTOBOOT_STOP_STR "s"
-#define CONFIG_ZERO_BOOTDELAY_CHECK
-#define CONFIG_RESET_TO_RETRY 60
-
-
-/*
- * Command line configuration.
- */
-
-#define CONFIG_CMD_ASKENV
-#define CONFIG_CMD_BOOTD
-#define CONFIG_CMD_CACHE
-#define CONFIG_CMD_DHCP
-#define CONFIG_CMD_ECHO
-#define CONFIG_CMD_SAVEENV
-#define CONFIG_CMD_FLASH
-#define CONFIG_CMD_IMI
-#define CONFIG_CMD_NET
-#define CONFIG_CMD_PCI
-#define CONFIG_CMD_RUN
-
-
-/*
- * BOOTP options
- */
-#define CONFIG_BOOTP_SUBNETMASK
-#define CONFIG_BOOTP_GATEWAY
-#define CONFIG_BOOTP_HOSTNAME
-#define CONFIG_BOOTP_BOOTPATH
-#define CONFIG_BOOTP_BOOTFILESIZE
-#define CONFIG_BOOTP_SUBNETMASK
-#define CONFIG_BOOTP_GATEWAY
-#define CONFIG_BOOTP_HOSTNAME
-#define CONFIG_BOOTP_NISDOMAIN
-#define CONFIG_BOOTP_BOOTPATH
-#define CONFIG_BOOTP_DNS
-#define CONFIG_BOOTP_DNS2
-#define CONFIG_BOOTP_SEND_HOSTNAME
-#define CONFIG_BOOTP_NTPSERVER
-#define CONFIG_BOOTP_TIMEOFFSET
-
-
-/*
- * Miscellaneous configurable options
- */
-#define CONFIG_SYS_LONGHELP /* undef to save memory */
-#define CONFIG_SYS_PROMPT "=> " /* Monitor Command Prompt */
-#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
-
-#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16)
-#define CONFIG_SYS_MAXARGS 16 /* Max number of command args */
-#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
-#define CONFIG_SYS_LOAD_ADDR 0x00100000 /* Default load address */
-
-#define CONFIG_BOOTCOMMAND "run nfsboot"
-#define CONFIG_BOOTARGS "root=/dev/mtdblock5 ro rootfstype=jffs2"
-
-#define CONFIG_NFSBOOTCOMMAND "bootp; run nfsargs addcons;bootm"
-
-#define CONFIG_EXTRA_ENV_SETTINGS \
- "console_nr=0\0" \
- "dhcp_client_id=mvBOX-XP\0" \
- "dhcp_vendor-class-identifier=mvBOX\0" \
- "adminboot=setenv bootargs root=/dev/mtdblock5 rw rootfstype=jffs2;run addcons;bootm ffc00000\0" \
- "flashboot=setenv bootargs root=/dev/mtdblock5 ro rootfstype=jffs2;run addcons;bootm ffc00000\0" \
- "safeboot=setenv bootargs root=/dev/mtdblock2 rw rootfstype=cramfs;run addcons;bootm ffc00000\0" \
- "hdboot=setenv bootargs root=/dev/hda1;run addcons;bootm ffc00000\0" \
- "nfsargs=setenv bootargs root=/dev/nfs rw nfsroot=${serverip}:${rootpath} " \
- "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}:${hostname}::off\0" \
- "addcons=setenv bootargs ${bootargs} console=ttyS${console_nr},${baudrate}N8\0" \
- "mv_version=" MV_VERSION "\0" \
- "bootretry=30\0"
-
-#define CONFIG_OVERWRITE_ETHADDR_ONCE
-
-/*-----------------------------------------------------------------------
- * PCI stuff
- *-----------------------------------------------------------------------
- */
-
-#define CONFIG_PCI
-#define CONFIG_PCI_INDIRECT_BRIDGE
-#define CONFIG_PCI_PNP
-#define CONFIG_PCI_SCAN_SHOW
-
-#define CONFIG_NET_RETRY_COUNT 5
-
-#define CONFIG_TULIP
-#define CONFIG_TULIP_FIX_DAVICOM 1
-#define CONFIG_ETHADDR b6:b4:45:eb:fb:c0
-
-#define CONFIG_HW_WATCHDOG
-
-/*-----------------------------------------------------------------------
- * Start addresses for the final memory configuration
- * (Set up by the startup code)
- * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0
- */
-#define CONFIG_SYS_SDRAM_BASE 0x00000000
-
-#define CONFIG_SYS_FLASH_BASE 0xFFF00000
-#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE
-
-#define CONFIG_SYS_RESET_ADDRESS 0xFFF00100
-#define CONFIG_SYS_EUMB_ADDR 0xFC000000
-
-#define CONFIG_SYS_MONITOR_LEN 0x00100000
-#define CONFIG_SYS_MALLOC_LEN (512 << 10) /* Reserve some kB for malloc() */
-
-#define CONFIG_SYS_MEMTEST_START 0x00100000 /* memtest works on */
-#define CONFIG_SYS_MEMTEST_END 0x00800000 /* 1M ... 8M in DRAM */
-
-/* Maximum amount of RAM. */
-#define CONFIG_SYS_MAX_RAM_SIZE 0x10000000 /* 0 .. 256MB of (S)DRAM */
-
-
-#if CONFIG_SYS_MONITOR_BASE >= CONFIG_SYS_FLASH_BASE
-#undef CONFIG_SYS_RAMBOOT
-#else
-#define CONFIG_SYS_RAMBOOT
-#endif
-
-#define CONFIG_SYS_ISA_IO 0xFE000000
-
-/*
- * serial configuration
- */
-#define CONFIG_SYS_NS16550
-#define CONFIG_SYS_NS16550_SERIAL
-
-#define CONFIG_SYS_NS16550_REG_SIZE 1
-
-#define CONFIG_SYS_NS16550_CLK get_bus_freq(0)
-
-#define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_EUMB_ADDR + 0x4500)
-#define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_EUMB_ADDR + 0x4600)
-
-/*-----------------------------------------------------------------------
- * Definitions for initial stack pointer and data area
- */
-#define CONFIG_SYS_INIT_RAM_ADDR 0x40000000
-#define CONFIG_SYS_INIT_RAM_SIZE 0x1000
-#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
-
-/*
- * Low Level Configuration Settings
- * (address mappings, register initial values, etc.)
- * You should know what you are doing if you make changes here.
- * For the detail description refer to the MPC8240 user's manual.
- */
-
-#define CONFIG_SYS_CLK_FREQ 33000000
-#define CONFIG_SYS_HZ 10000
-
-/* Bit-field values for MCCR1. */
-#define CONFIG_SYS_ROMNAL 7
-#define CONFIG_SYS_ROMFAL 11
-
-/* Bit-field values for MCCR2. */
-#define CONFIG_SYS_TSWAIT 0x5
-#define CONFIG_SYS_REFINT 430
-
-/* Burst To Precharge. Bits of this value go to MCCR3 and MCCR4. */
-#define CONFIG_SYS_BSTOPRE 121
-
-/* Bit-field values for MCCR3. */
-#define CONFIG_SYS_REFREC 8
-
-/* Bit-field values for MCCR4. */
-#define CONFIG_SYS_PRETOACT 3
-#define CONFIG_SYS_ACTTOPRE 5
-#define CONFIG_SYS_ACTORW 3
-#define CONFIG_SYS_SDMODE_CAS_LAT 3
-#define CONFIG_SYS_REGISTERD_TYPE_BUFFER 1
-#define CONFIG_SYS_EXTROM 1
-#define CONFIG_SYS_REGDIMM 0
-#define CONFIG_SYS_DBUS_SIZE2 1
-#define CONFIG_SYS_SDMODE_WRAP 0
-
-#define CONFIG_SYS_PGMAX 0x32
-#define CONFIG_SYS_SDRAM_DSCD 0x20
-
-/* Memory bank settings.
- * Only bits 20-29 are actually used from these vales to set the
- * start/end addresses. The upper two bits will always be 0, and the lower
- * 20 bits will be 0x00000 for a start address, or 0xfffff for an end
- * address. Refer to the MPC8240 book.
- */
-
-#define CONFIG_SYS_BANK0_START 0x00000000
-#define CONFIG_SYS_BANK0_END (CONFIG_SYS_MAX_RAM_SIZE - 1)
-#define CONFIG_SYS_BANK0_ENABLE 1
-#define CONFIG_SYS_BANK1_START 0x3ff00000
-#define CONFIG_SYS_BANK1_END 0x3fffffff
-#define CONFIG_SYS_BANK1_ENABLE 0
-#define CONFIG_SYS_BANK2_START 0x3ff00000
-#define CONFIG_SYS_BANK2_END 0x3fffffff
-#define CONFIG_SYS_BANK2_ENABLE 0
-#define CONFIG_SYS_BANK3_START 0x3ff00000
-#define CONFIG_SYS_BANK3_END 0x3fffffff
-#define CONFIG_SYS_BANK3_ENABLE 0
-#define CONFIG_SYS_BANK4_START 0x3ff00000
-#define CONFIG_SYS_BANK4_END 0x3fffffff
-#define CONFIG_SYS_BANK4_ENABLE 0
-#define CONFIG_SYS_BANK5_START 0x3ff00000
-#define CONFIG_SYS_BANK5_END 0x3fffffff
-#define CONFIG_SYS_BANK5_ENABLE 0
-#define CONFIG_SYS_BANK6_START 0x3ff00000
-#define CONFIG_SYS_BANK6_END 0x3fffffff
-#define CONFIG_SYS_BANK6_ENABLE 0
-#define CONFIG_SYS_BANK7_START 0x3ff00000
-#define CONFIG_SYS_BANK7_END 0x3fffffff
-#define CONFIG_SYS_BANK7_ENABLE 0
-
-#define CONFIG_SYS_ODCR 0xff
-
-#define CONFIG_SYS_IBAT0L (CONFIG_SYS_SDRAM_BASE | BATL_PP_10 | BATL_MEMCOHERENCE)
-#define CONFIG_SYS_IBAT0U (CONFIG_SYS_SDRAM_BASE | BATU_BL_256M | BATU_VS | BATU_VP)
-
-#define CONFIG_SYS_IBAT1L (CONFIG_SYS_INIT_RAM_ADDR | BATL_PP_10 | BATL_MEMCOHERENCE)
-#define CONFIG_SYS_IBAT1U (CONFIG_SYS_INIT_RAM_ADDR | BATU_BL_128K | BATU_VS | BATU_VP)
-
-#define CONFIG_SYS_IBAT2L (0x80000000 | BATL_PP_10 | BATL_CACHEINHIBIT)
-#define CONFIG_SYS_IBAT2U (0x80000000 | BATU_BL_256M | BATU_VS | BATU_VP)
-
-#define CONFIG_SYS_IBAT3L (0xF0000000 | BATL_PP_10 | BATL_CACHEINHIBIT)
-#define CONFIG_SYS_IBAT3U (0xF0000000 | BATU_BL_256M | BATU_VS | BATU_VP)
-
-#define CONFIG_SYS_DBAT0L CONFIG_SYS_IBAT0L
-#define CONFIG_SYS_DBAT0U CONFIG_SYS_IBAT0U
-#define CONFIG_SYS_DBAT1L CONFIG_SYS_IBAT1L
-#define CONFIG_SYS_DBAT1U CONFIG_SYS_IBAT1U
-#define CONFIG_SYS_DBAT2L CONFIG_SYS_IBAT2L
-#define CONFIG_SYS_DBAT2U CONFIG_SYS_IBAT2U
-#define CONFIG_SYS_DBAT3L CONFIG_SYS_IBAT3L
-#define CONFIG_SYS_DBAT3U CONFIG_SYS_IBAT3U
-
-/*
- * For booting Linux, the board info and command line data
- * have to be in the first 8 MB of memory, since this is
- * the maximum mapped by the Linux kernel during initialization.
- */
-#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
-
-/*-----------------------------------------------------------------------
- * FLASH organization
- */
-#undef CONFIG_SYS_FLASH_PROTECTION
-#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* Max number of flash banks */
-#define CONFIG_SYS_MAX_FLASH_SECT 63 /* Max number of sectors per flash */
-
-#define CONFIG_SYS_FLASH_ERASE_TOUT 12000
-#define CONFIG_SYS_FLASH_WRITE_TOUT 1000
-
-
-#define CONFIG_ENV_IS_IN_FLASH
-
-#define CONFIG_ENV_OFFSET 0x00010000
-#define CONFIG_ENV_SIZE 0x00010000
-#define CONFIG_ENV_SECT_SIZE 0x00010000
-
-/*-----------------------------------------------------------------------
- * Cache Configuration
- */
-#define CONFIG_SYS_CACHELINE_SIZE 32
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_SYS_CACHELINE_SHIFT 5 /* log base 2 of the above value */
-#endif
-#endif /* __CONFIG_H */
projects / platform / kernel / u-boot.git / blobdiff