Replace CONFIG_SYS_GBL_DATA_SIZE by auto-generated value

[platform/kernel/u-boot.git] / include / configs / MPC8641HPCN.h

diff --git a/include/configs/MPC8641HPCN.h b/include/configs/MPC8641HPCN.h
index 0d1f779..ab3ae5b 100644 (file)
--- a/include/configs/MPC8641HPCN.h
+++ b/include/configs/MPC8641HPCN.h
@@ -41,6 +41,12 @@
 /*#define CONFIG_PHYS_64BIT    1*/     /* Place devices in 36-bit space */
 #define CONFIG_ADDR_MAP                1       /* Use addr map */
 
+/*
+ * default CCSRBAR is at 0xff700000
+ * assume U-Boot is less than 0.5MB
+ */
+#define        CONFIG_SYS_TEXT_BASE    0xeff00000
+
 #ifdef RUN_DIAG
 #define CONFIG_SYS_DIAG_ADDR        CONFIG_SYS_FLASH_BASE
 #endif
@@ -68,6 +74,7 @@
 #define CONFIG_TSEC_ENET               /* tsec ethernet support */
 #define CONFIG_ENV_OVERWRITE
 
+#define CONFIG_BAT_RW          1       /* Use common BAT rw code */
 #define CONFIG_HIGH_BATS       1       /* High BATs supported and enabled */
 #define CONFIG_SYS_NUM_ADDR_MAP 8      /* Number of addr map slots = 8 dbats */
 
@@ -122,6 +129,8 @@ extern unsigned long get_board_sys_clk(unsigned long dummy);
 #define CONFIG_SYS_CCSRBAR_PHYS                CONFIG_SYS_CCSRBAR_PHYS_LOW
 #endif
 
+#define CONFIG_HWCONFIG        /* use hwconfig to control memory interleaving */
+
 /*
  * DDR Setup
  */
@@ -236,7 +245,7 @@ extern unsigned long get_board_sys_clk(unsigned long dummy);
 #undef CONFIG_SYS_FLASH_CHECKSUM
 #define CONFIG_SYS_FLASH_ERASE_TOUT    60000   /* Flash Erase Timeout (ms) */
 #define CONFIG_SYS_FLASH_WRITE_TOUT    500     /* Flash Write Timeout (ms) */
-#define CONFIG_SYS_MONITOR_BASE                TEXT_BASE       /* start of monitor */
+#define CONFIG_SYS_MONITOR_BASE                CONFIG_SYS_TEXT_BASE    /* start of monitor */
 #define CONFIG_SYS_MONITOR_BASE_EARLY   0xfff00000     /* early monitor loc */
 
 #define CONFIG_FLASH_CFI_DRIVER
@@ -262,10 +271,9 @@ extern unsigned long get_board_sys_clk(unsigned long dummy);
 #else
 #define CONFIG_SYS_INIT_RAM_ADDR       0xf8400000      /* Initial RAM address */
 #endif
-#define CONFIG_SYS_INIT_RAM_END        0x4000          /* End of used area in RAM */
+#define CONFIG_SYS_INIT_RAM_SIZE       0x4000          /* Size of used area in RAM */
 
-#define CONFIG_SYS_GBL_DATA_SIZE       128             /* num bytes initial data */
-#define CONFIG_SYS_GBL_DATA_OFFSET     (CONFIG_SYS_INIT_RAM_END - CONFIG_SYS_GBL_DATA_SIZE)
+#define CONFIG_SYS_GBL_DATA_OFFSET     (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
 #define CONFIG_SYS_INIT_SP_OFFSET      CONFIG_SYS_GBL_DATA_OFFSET
 
 #define CONFIG_SYS_MONITOR_LEN         (256 * 1024)    /* Reserve 256 kB for Mon */
@@ -273,7 +281,6 @@ extern unsigned long get_board_sys_clk(unsigned long dummy);
 
 /* Serial Port */
 #define CONFIG_CONS_INDEX     1
-#undef CONFIG_SERIAL_SOFTWARE_FIFO
 #define CONFIG_SYS_NS16550
 #define CONFIG_SYS_NS16550_SERIAL
 #define CONFIG_SYS_NS16550_REG_SIZE    1
@@ -585,7 +592,7 @@ extern unsigned long get_board_sys_clk(unsigned long dummy);
 /* Map the last 1M of flash where we're running from reset */
 #define CONFIG_SYS_DBAT6L_EARLY        (CONFIG_SYS_MONITOR_BASE_EARLY | BATL_PP_RW \
                                 | BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
-#define CONFIG_SYS_DBAT6U_EARLY        (TEXT_BASE | BATU_BL_1M | BATU_VS | BATU_VP)
+#define CONFIG_SYS_DBAT6U_EARLY        (CONFIG_SYS_TEXT_BASE | BATU_BL_1M | BATU_VS | BATU_VP)
 #define CONFIG_SYS_IBAT6L_EARLY        (CONFIG_SYS_MONITOR_BASE_EARLY | BATL_PP_RW \
                                 | BATL_MEMCOHERENCE)
 #define CONFIG_SYS_IBAT6U_EARLY        CONFIG_SYS_DBAT6U_EARLY
@@ -673,14 +680,6 @@ extern unsigned long get_board_sys_clk(unsigned long dummy);
  */
 #define CONFIG_SYS_BOOTMAPSZ   (8 << 20)       /* Initial Memory map for Linux*/
 
-/*
- * Internal Definitions
- *
- * Boot Flags
- */
-#define BOOTFLAG_COLD  0x01            /* Normal Power-On: Boot from FLASH */
-#define BOOTFLAG_WARM  0x02            /* Software reboot */
-
 #if defined(CONFIG_CMD_KGDB)
     #define CONFIG_KGDB_BAUDRATE       230400  /* speed to run kgdb serial port */
     #define CONFIG_KGDB_SER_INDEX      2       /* which serial port to use */
@@ -726,11 +725,11 @@ extern unsigned long get_board_sys_clk(unsigned long dummy);
        "netdev=eth0\0"                                                 \
        "uboot=" MK_STR(CONFIG_UBOOTPATH) "\0"                          \
        "tftpflash=tftpboot $loadaddr $uboot; "                         \
-               "protect off " MK_STR(TEXT_BASE) " +$filesize; "        \
-               "erase " MK_STR(TEXT_BASE) " +$filesize; "              \
-               "cp.b $loadaddr " MK_STR(TEXT_BASE) " $filesize; "      \
-               "protect on " MK_STR(TEXT_BASE) " +$filesize; "         \
-               "cmp.b $loadaddr " MK_STR(TEXT_BASE) " $filesize\0"     \
+               "protect off " MK_STR(CONFIG_SYS_TEXT_BASE) " +$filesize; "     \
+               "erase " MK_STR(CONFIG_SYS_TEXT_BASE) " +$filesize; "           \
+               "cp.b $loadaddr " MK_STR(CONFIG_SYS_TEXT_BASE) " $filesize; "   \
+               "protect on " MK_STR(CONFIG_SYS_TEXT_BASE) " +$filesize; "              \
+               "cmp.b $loadaddr " MK_STR(CONFIG_SYS_TEXT_BASE) " $filesize\0"  \
        "consoledev=ttyS0\0"                                            \
        "ramdiskaddr=2000000\0"                                         \
        "ramdiskfile=your.ramdisk.u-boot\0"                             \