+++ /dev/null
-/* SPDX-License-Identifier: GPL-2.0+ */
-/*
- * Copyright 2007-2008,2010-2011 Freescale Semiconductor, Inc.
- */
-
-/*
- * mpc8572ds board configuration file
- *
- */
-#ifndef __CONFIG_H
-#define __CONFIG_H
-
-#include "../board/freescale/common/ics307_clk.h"
-
-#ifndef CONFIG_RESET_VECTOR_ADDRESS
-#define CONFIG_RESET_VECTOR_ADDRESS 0xeffffffc
-#endif
-
-#ifndef CONFIG_SYS_MONITOR_BASE
-#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */
-#endif
-
-/* High Level Configuration Options */
-
-#define CONFIG_PCIE1 1 /* PCIE controller 1 (slot 1) */
-#define CONFIG_PCIE2 1 /* PCIE controller 2 (slot 2) */
-#define CONFIG_PCIE3 1 /* PCIE controller 3 (ULI bridge) */
-#define CONFIG_FSL_PCI_INIT 1 /* Use common FSL init code */
-#define CONFIG_PCI_INDIRECT_BRIDGE 1 /* indirect PCI bridge support */
-#define CONFIG_FSL_PCIE_RESET 1 /* need PCIe reset errata */
-#define CONFIG_SYS_PCI_64BIT 1 /* enable 64-bit PCI resources */
-
-#define CONFIG_ENV_OVERWRITE
-
-#define CONFIG_SYS_CLK_FREQ get_board_sys_clk() /* sysclk for MPC85xx */
-#define CONFIG_DDR_CLK_FREQ get_board_ddr_clk() /* ddrclk for MPC85xx */
-#define CONFIG_ICS307_REFCLK_HZ 33333000 /* ICS307 clock chip ref freq */
-
-/*
- * These can be toggled for performance analysis, otherwise use default.
- */
-#define CONFIG_L2_CACHE /* toggle L2 cache */
-#define CONFIG_BTB /* toggle branch predition */
-
-#define CONFIG_ENABLE_36BIT_PHYS 1
-
-#ifdef CONFIG_PHYS_64BIT
-#define CONFIG_ADDR_MAP 1
-#define CONFIG_SYS_NUM_ADDR_MAP 16 /* number of TLB1 entries */
-#endif
-
-#define CONFIG_SYS_MEMTEST_START 0x00000000 /* memtest works on */
-#define CONFIG_SYS_MEMTEST_END 0x7fffffff
-
-/*
- * Config the L2 Cache as L2 SRAM
- */
-#define CONFIG_SYS_INIT_L2_ADDR 0xf8f80000
-#ifdef CONFIG_PHYS_64BIT
-#define CONFIG_SYS_INIT_L2_ADDR_PHYS 0xff8f80000ull
-#else
-#define CONFIG_SYS_INIT_L2_ADDR_PHYS CONFIG_SYS_INIT_L2_ADDR
-#endif
-#define CONFIG_SYS_L2_SIZE (512 << 10)
-#define CONFIG_SYS_INIT_L2_END (CONFIG_SYS_INIT_L2_ADDR + CONFIG_SYS_L2_SIZE)
-
-#define CONFIG_SYS_CCSRBAR 0xffe00000
-#define CONFIG_SYS_CCSRBAR_PHYS_LOW CONFIG_SYS_CCSRBAR
-
-#if defined(CONFIG_NAND_SPL)
-#define CONFIG_SYS_CCSR_DO_NOT_RELOCATE
-#endif
-
-/* DDR Setup */
-#define CONFIG_VERY_BIG_RAM
-#undef CONFIG_FSL_DDR_INTERACTIVE
-#define CONFIG_SPD_EEPROM /* Use SPD EEPROM for DDR setup */
-#define CONFIG_DDR_SPD
-
-#define CONFIG_DDR_ECC
-#define CONFIG_ECC_INIT_VIA_DDRCONTROLLER
-#define CONFIG_MEM_INIT_VALUE 0xDeadBeef
-
-#define CONFIG_SYS_DDR_SDRAM_BASE 0x00000000
-#define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE
-
-#define CONFIG_DIMM_SLOTS_PER_CTLR 1
-#define CONFIG_CHIP_SELECTS_PER_CTRL 2
-
-/* I2C addresses of SPD EEPROMs */
-#define CONFIG_SYS_SPD_BUS_NUM 1 /* SPD EEPROMS locate on I2C bus 1 */
-#define SPD_EEPROM_ADDRESS1 0x51 /* CTLR 0 DIMM 0 */
-#define SPD_EEPROM_ADDRESS2 0x52 /* CTLR 1 DIMM 0 */
-
-/* These are used when DDR doesn't use SPD. */
-#define CONFIG_SYS_SDRAM_SIZE 512 /* DDR is 512MB */
-#define CONFIG_SYS_DDR_CS0_BNDS 0x0000001F
-#define CONFIG_SYS_DDR_CS0_CONFIG 0x80010202 /* Enable, no interleaving */
-#define CONFIG_SYS_DDR_TIMING_3 0x00020000
-#define CONFIG_SYS_DDR_TIMING_0 0x00260802
-#define CONFIG_SYS_DDR_TIMING_1 0x626b2634
-#define CONFIG_SYS_DDR_TIMING_2 0x062874cf
-#define CONFIG_SYS_DDR_MODE_1 0x00440462
-#define CONFIG_SYS_DDR_MODE_2 0x00000000
-#define CONFIG_SYS_DDR_INTERVAL 0x0c300100
-#define CONFIG_SYS_DDR_DATA_INIT 0xdeadbeef
-#define CONFIG_SYS_DDR_CLK_CTRL 0x00800000
-#define CONFIG_SYS_DDR_OCD_CTRL 0x00000000
-#define CONFIG_SYS_DDR_OCD_STATUS 0x00000000
-#define CONFIG_SYS_DDR_CONTROL 0xc3000008 /* Type = DDR2 */
-#define CONFIG_SYS_DDR_CONTROL2 0x24400000
-
-#define CONFIG_SYS_DDR_ERR_INT_EN 0x0000000d
-#define CONFIG_SYS_DDR_ERR_DIS 0x00000000
-#define CONFIG_SYS_DDR_SBE 0x00010000
-
-/*
- * Make sure required options are set
- */
-#ifndef CONFIG_SPD_EEPROM
-#error ("CONFIG_SPD_EEPROM is required")
-#endif
-
-#undef CONFIG_CLOCKS_IN_MHZ
-
-/*
- * Memory map
- *
- * 0x0000_0000 0x7fff_ffff DDR 2G Cacheable
- * 0x8000_0000 0xbfff_ffff PCI Express Mem 1G non-cacheable
- * 0xc000_0000 0xdfff_ffff PCI 512M non-cacheable
- * 0xe100_0000 0xe3ff_ffff PCI IO range 4M non-cacheable
- *
- * Localbus cacheable (TBD)
- * 0xXXXX_XXXX 0xXXXX_XXXX SRAM YZ M Cacheable
- *
- * Localbus non-cacheable
- * 0xe000_0000 0xe80f_ffff Promjet/free 128M non-cacheable
- * 0xe800_0000 0xefff_ffff FLASH 128M non-cacheable
- * 0xffa0_0000 0xffaf_ffff NAND 1M non-cacheable
- * 0xffdf_0000 0xffdf_7fff PIXIS 32K non-cacheable TLB0
- * 0xffd0_0000 0xffd0_3fff L1 for stack 16K Cacheable TLB0
- * 0xffe0_0000 0xffef_ffff CCSR 1M non-cacheable
- */
-
-/*
- * Local Bus Definitions
- */
-#define CONFIG_SYS_FLASH_BASE 0xe0000000 /* start of FLASH 128M */
-#ifdef CONFIG_PHYS_64BIT
-#define CONFIG_SYS_FLASH_BASE_PHYS 0xfe0000000ull
-#else
-#define CONFIG_SYS_FLASH_BASE_PHYS CONFIG_SYS_FLASH_BASE
-#endif
-
-#define CONFIG_FLASH_BR_PRELIM \
- (BR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS + 0x8000000) | BR_PS_16 | BR_V)
-#define CONFIG_FLASH_OR_PRELIM 0xf8000ff7
-
-#define CONFIG_SYS_BR1_PRELIM (BR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS) | BR_PS_16 | BR_V)
-#define CONFIG_SYS_OR1_PRELIM 0xf8000ff7
-
-#define CONFIG_SYS_FLASH_BANKS_LIST {CONFIG_SYS_FLASH_BASE_PHYS + 0x8000000, CONFIG_SYS_FLASH_BASE_PHYS}
-#define CONFIG_SYS_FLASH_QUIET_TEST
-#define CONFIG_FLASH_SHOW_PROGRESS 45 /* count down from 45/5: 9..1 */
-
-#define CONFIG_SYS_MAX_FLASH_BANKS 2 /* number of banks */
-#define CONFIG_SYS_MAX_FLASH_SECT 1024 /* sectors per device */
-#undef CONFIG_SYS_FLASH_CHECKSUM
-#define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */
-#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */
-
-#undef CONFIG_SYS_RAMBOOT
-
-#define CONFIG_FLASH_CFI_DRIVER
-#define CONFIG_SYS_FLASH_CFI
-#define CONFIG_SYS_FLASH_EMPTY_INFO
-#define CONFIG_SYS_FLASH_AMD_CHECK_DQ7
-
-#define CONFIG_HWCONFIG /* enable hwconfig */
-#define CONFIG_FSL_PIXIS 1 /* use common PIXIS code */
-#define PIXIS_BASE 0xffdf0000 /* PIXIS registers */
-#ifdef CONFIG_PHYS_64BIT
-#define PIXIS_BASE_PHYS 0xfffdf0000ull
-#else
-#define PIXIS_BASE_PHYS PIXIS_BASE
-#endif
-
-#define CONFIG_SYS_BR3_PRELIM (BR_PHYS_ADDR(PIXIS_BASE_PHYS) | BR_PS_8 | BR_V)
-#define CONFIG_SYS_OR3_PRELIM 0xffffeff7 /* 32KB but only 4k mapped */
-
-#define PIXIS_ID 0x0 /* Board ID at offset 0 */
-#define PIXIS_VER 0x1 /* Board version at offset 1 */
-#define PIXIS_PVER 0x2 /* PIXIS FPGA version at offset 2 */
-#define PIXIS_CSR 0x3 /* PIXIS General control/status register */
-#define PIXIS_RST 0x4 /* PIXIS Reset Control register */
-#define PIXIS_PWR 0x5 /* PIXIS Power status register */
-#define PIXIS_AUX 0x6 /* Auxiliary 1 register */
-#define PIXIS_SPD 0x7 /* Register for SYSCLK speed */
-#define PIXIS_AUX2 0x8 /* Auxiliary 2 register */
-#define PIXIS_VCTL 0x10 /* VELA Control Register */
-#define PIXIS_VSTAT 0x11 /* VELA Status Register */
-#define PIXIS_VCFGEN0 0x12 /* VELA Config Enable 0 */
-#define PIXIS_VCFGEN1 0x13 /* VELA Config Enable 1 */
-#define PIXIS_VCORE0 0x14 /* VELA VCORE0 Register */
-#define PIXIS_VBOOT 0x16 /* VELA VBOOT Register */
-#define PIXIS_VBOOT_LBMAP 0xc0 /* VBOOT - CFG_LBMAP */
-#define PIXIS_VBOOT_LBMAP_NOR0 0x00 /* cfg_lbmap - boot from NOR 0 */
-#define PIXIS_VBOOT_LBMAP_PJET 0x01 /* cfg_lbmap - boot from projet */
-#define PIXIS_VBOOT_LBMAP_NAND 0x02 /* cfg_lbmap - boot from NAND */
-#define PIXIS_VBOOT_LBMAP_NOR1 0x03 /* cfg_lbmap - boot from NOR 1 */
-#define PIXIS_VSPEED0 0x17 /* VELA VSpeed 0 */
-#define PIXIS_VSPEED1 0x18 /* VELA VSpeed 1 */
-#define PIXIS_VSPEED2 0x19 /* VELA VSpeed 2 */
-#define PIXIS_VSYSCLK0 0x1C /* VELA SYSCLK0 Register */
-#define PIXIS_VSYSCLK1 0x1D /* VELA SYSCLK1 Register */
-#define PIXIS_VSYSCLK2 0x1E /* VELA SYSCLK2 Register */
-#define PIXIS_VDDRCLK0 0x1F /* VELA DDRCLK0 Register */
-#define PIXIS_VDDRCLK1 0x20 /* VELA DDRCLK1 Register */
-#define PIXIS_VDDRCLK2 0x21 /* VELA DDRCLK2 Register */
-#define PIXIS_VWATCH 0x24 /* Watchdog Register */
-#define PIXIS_LED 0x25 /* LED Register */
-
-#define PIXIS_SPD_SYSCLK_MASK 0x7 /* SYSCLK option */
-
-/* old pixis referenced names */
-#define PIXIS_VCLKH 0x19 /* VELA VCLKH register */
-#define PIXIS_VCLKL 0x1A /* VELA VCLKL register */
-#define CONFIG_SYS_PIXIS_VBOOT_MASK 0xc0
-#define PIXIS_VSPEED2_TSEC1SER 0x8
-#define PIXIS_VSPEED2_TSEC2SER 0x4
-#define PIXIS_VSPEED2_TSEC3SER 0x2
-#define PIXIS_VSPEED2_TSEC4SER 0x1
-#define PIXIS_VCFGEN1_TSEC1SER 0x20
-#define PIXIS_VCFGEN1_TSEC2SER 0x20
-#define PIXIS_VCFGEN1_TSEC3SER 0x20
-#define PIXIS_VCFGEN1_TSEC4SER 0x20
-#define PIXIS_VSPEED2_MASK (PIXIS_VSPEED2_TSEC1SER \
- | PIXIS_VSPEED2_TSEC2SER \
- | PIXIS_VSPEED2_TSEC3SER \
- | PIXIS_VSPEED2_TSEC4SER)
-#define PIXIS_VCFGEN1_MASK (PIXIS_VCFGEN1_TSEC1SER \
- | PIXIS_VCFGEN1_TSEC2SER \
- | PIXIS_VCFGEN1_TSEC3SER \
- | PIXIS_VCFGEN1_TSEC4SER)
-
-#define CONFIG_SYS_INIT_RAM_LOCK 1
-#define CONFIG_SYS_INIT_RAM_ADDR 0xffd00000 /* Initial L1 address */
-#define CONFIG_SYS_INIT_RAM_SIZE 0x00004000 /* Size of used area in RAM */
-
-#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
-#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
-
-#define CONFIG_SYS_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Mon */
-#define CONFIG_SYS_MALLOC_LEN (1024 * 1024) /* Reserved for malloc */
-
-#ifndef CONFIG_NAND_SPL
-#define CONFIG_SYS_NAND_BASE 0xffa00000
-#ifdef CONFIG_PHYS_64BIT
-#define CONFIG_SYS_NAND_BASE_PHYS 0xfffa00000ull
-#else
-#define CONFIG_SYS_NAND_BASE_PHYS CONFIG_SYS_NAND_BASE
-#endif
-#else
-#define CONFIG_SYS_NAND_BASE 0xfff00000
-#ifdef CONFIG_PHYS_64BIT
-#define CONFIG_SYS_NAND_BASE_PHYS 0xffff00000ull
-#else
-#define CONFIG_SYS_NAND_BASE_PHYS CONFIG_SYS_NAND_BASE
-#endif
-#endif
-
-#define CONFIG_SYS_NAND_BASE_LIST { CONFIG_SYS_NAND_BASE,\
- CONFIG_SYS_NAND_BASE + 0x40000, \
- CONFIG_SYS_NAND_BASE + 0x80000,\
- CONFIG_SYS_NAND_BASE + 0xC0000}
-#define CONFIG_SYS_MAX_NAND_DEVICE 4
-#define CONFIG_NAND_FSL_ELBC 1
-#define CONFIG_SYS_NAND_BLOCK_SIZE (128 * 1024)
-#define CONFIG_SYS_NAND_MAX_OOBFREE 5
-#define CONFIG_SYS_NAND_MAX_ECCPOS 56
-
-/* NAND boot: 4K NAND loader config */
-#define CONFIG_SYS_NAND_SPL_SIZE 0x1000
-#define CONFIG_SYS_NAND_U_BOOT_SIZE ((512 << 10) - 0x2000)
-#define CONFIG_SYS_NAND_U_BOOT_DST (CONFIG_SYS_INIT_L2_ADDR)
-#define CONFIG_SYS_NAND_U_BOOT_START \
- (CONFIG_SYS_INIT_L2_ADDR + CONFIG_SYS_NAND_SPL_SIZE)
-#define CONFIG_SYS_NAND_U_BOOT_OFFS (0)
-#define CONFIG_SYS_NAND_U_BOOT_RELOC (CONFIG_SYS_INIT_L2_END - 0x2000)
-#define CONFIG_SYS_NAND_U_BOOT_RELOC_SP ((CONFIG_SYS_INIT_L2_END - 1) & ~0xF)
-
-/* NAND flash config */
-#define CONFIG_SYS_NAND_BR_PRELIM (BR_PHYS_ADDR(CONFIG_SYS_NAND_BASE_PHYS) \
- | (2<<BR_DECC_SHIFT) /* Use HW ECC */ \
- | BR_PS_8 /* Port Size = 8 bit */ \
- | BR_MS_FCM /* MSEL = FCM */ \
- | BR_V) /* valid */
-#define CONFIG_SYS_NAND_OR_PRELIM (0xFFFC0000 /* length 256K */ \
- | OR_FCM_PGS /* Large Page*/ \
- | OR_FCM_CSCT \
- | OR_FCM_CST \
- | OR_FCM_CHT \
- | OR_FCM_SCY_1 \
- | OR_FCM_TRLX \
- | OR_FCM_EHTR)
-
-#define CONFIG_SYS_BR0_PRELIM CONFIG_FLASH_BR_PRELIM /* NOR Base Address */
-#define CONFIG_SYS_OR0_PRELIM CONFIG_FLASH_OR_PRELIM /* NOR Options */
-#define CONFIG_SYS_BR2_PRELIM CONFIG_SYS_NAND_BR_PRELIM /* NAND Base Address */
-#define CONFIG_SYS_OR2_PRELIM CONFIG_SYS_NAND_OR_PRELIM /* NAND Options */
-#define CONFIG_SYS_BR4_PRELIM (BR_PHYS_ADDR(CONFIG_SYS_NAND_BASE_PHYS + 0x40000) \
- | (2<<BR_DECC_SHIFT) /* Use HW ECC */ \
- | BR_PS_8 /* Port Size = 8 bit */ \
- | BR_MS_FCM /* MSEL = FCM */ \
- | BR_V) /* valid */
-#define CONFIG_SYS_OR4_PRELIM CONFIG_SYS_NAND_OR_PRELIM /* NAND Options */
-#define CONFIG_SYS_BR5_PRELIM (BR_PHYS_ADDR(CONFIG_SYS_NAND_BASE_PHYS + 0x80000)\
- | (2<<BR_DECC_SHIFT) /* Use HW ECC */ \
- | BR_PS_8 /* Port Size = 8 bit */ \
- | BR_MS_FCM /* MSEL = FCM */ \
- | BR_V) /* valid */
-#define CONFIG_SYS_OR5_PRELIM CONFIG_SYS_NAND_OR_PRELIM /* NAND Options */
-
-#define CONFIG_SYS_BR6_PRELIM (BR_PHYS_ADDR(CONFIG_SYS_NAND_BASE_PHYS + 0xc0000)\
- | (2<<BR_DECC_SHIFT) /* Use HW ECC */ \
- | BR_PS_8 /* Port Size = 8 bit */ \
- | BR_MS_FCM /* MSEL = FCM */ \
- | BR_V) /* valid */
-#define CONFIG_SYS_OR6_PRELIM CONFIG_SYS_NAND_OR_PRELIM /* NAND Options */
-
-/* Serial Port - controlled on board with jumper J8
- * open - index 2
- * shorted - index 1
- */
-#define CONFIG_SYS_NS16550_SERIAL
-#define CONFIG_SYS_NS16550_REG_SIZE 1
-#define CONFIG_SYS_NS16550_CLK get_bus_freq(0)
-#ifdef CONFIG_NAND_SPL
-#define CONFIG_NS16550_MIN_FUNCTIONS
-#endif
-
-#define CONFIG_SYS_BAUDRATE_TABLE \
- {300, 600, 1200, 2400, 4800, 9600, 19200, 38400,115200}
-
-#define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_CCSRBAR+0x4500)
-#define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_CCSRBAR+0x4600)
-
-/* I2C */
-#define CONFIG_SYS_I2C
-#define CONFIG_SYS_I2C_FSL
-#define CONFIG_SYS_FSL_I2C_SPEED 400000
-#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F
-#define CONFIG_SYS_FSL_I2C_OFFSET 0x3000
-#define CONFIG_SYS_FSL_I2C2_SPEED 400000
-#define CONFIG_SYS_FSL_I2C2_SLAVE 0x7F
-#define CONFIG_SYS_FSL_I2C2_OFFSET 0x3100
-#define CONFIG_SYS_I2C_NOPROBES { {0, 0x29} }
-#define CONFIG_SYS_I2C_EEPROM_ADDR 0x57
-
-/*
- * I2C2 EEPROM
- */
-#define CONFIG_ID_EEPROM
-#ifdef CONFIG_ID_EEPROM
-#define CONFIG_SYS_I2C_EEPROM_NXID
-#endif
-#define CONFIG_SYS_I2C_EEPROM_ADDR 0x57
-#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1
-#define CONFIG_SYS_EEPROM_BUS_NUM 1
-
-/*
- * General PCI
- * Memory space is mapped 1-1, but I/O space must start from 0.
- */
-
-/* controller 3, direct to uli, tgtid 3, Base address 8000 */
-#define CONFIG_SYS_PCIE3_NAME "ULI"
-#define CONFIG_SYS_PCIE3_MEM_VIRT 0x80000000
-#ifdef CONFIG_PHYS_64BIT
-#define CONFIG_SYS_PCIE3_MEM_BUS 0xe0000000
-#define CONFIG_SYS_PCIE3_MEM_PHYS 0xc00000000ull
-#else
-#define CONFIG_SYS_PCIE3_MEM_BUS 0x80000000
-#define CONFIG_SYS_PCIE3_MEM_PHYS 0x80000000
-#endif
-#define CONFIG_SYS_PCIE3_MEM_SIZE 0x20000000 /* 512M */
-#define CONFIG_SYS_PCIE3_IO_VIRT 0xffc00000
-#define CONFIG_SYS_PCIE3_IO_BUS 0x00000000
-#ifdef CONFIG_PHYS_64BIT
-#define CONFIG_SYS_PCIE3_IO_PHYS 0xfffc00000ull
-#else
-#define CONFIG_SYS_PCIE3_IO_PHYS 0xffc00000
-#endif
-#define CONFIG_SYS_PCIE3_IO_SIZE 0x00010000 /* 64k */
-
-/* controller 2, Slot 2, tgtid 2, Base address 9000 */
-#define CONFIG_SYS_PCIE2_NAME "Slot 1"
-#define CONFIG_SYS_PCIE2_MEM_VIRT 0xa0000000
-#ifdef CONFIG_PHYS_64BIT
-#define CONFIG_SYS_PCIE2_MEM_BUS 0xe0000000
-#define CONFIG_SYS_PCIE2_MEM_PHYS 0xc20000000ull
-#else
-#define CONFIG_SYS_PCIE2_MEM_BUS 0xa0000000
-#define CONFIG_SYS_PCIE2_MEM_PHYS 0xa0000000
-#endif
-#define CONFIG_SYS_PCIE2_MEM_SIZE 0x20000000 /* 512M */
-#define CONFIG_SYS_PCIE2_IO_VIRT 0xffc10000
-#define CONFIG_SYS_PCIE2_IO_BUS 0x00000000
-#ifdef CONFIG_PHYS_64BIT
-#define CONFIG_SYS_PCIE2_IO_PHYS 0xfffc10000ull
-#else
-#define CONFIG_SYS_PCIE2_IO_PHYS 0xffc10000
-#endif
-#define CONFIG_SYS_PCIE2_IO_SIZE 0x00010000 /* 64k */
-
-/* controller 1, Slot 1, tgtid 1, Base address a000 */
-#define CONFIG_SYS_PCIE1_NAME "Slot 2"
-#define CONFIG_SYS_PCIE1_MEM_VIRT 0xc0000000
-#ifdef CONFIG_PHYS_64BIT
-#define CONFIG_SYS_PCIE1_MEM_BUS 0xe0000000
-#define CONFIG_SYS_PCIE1_MEM_PHYS 0xc40000000ull
-#else
-#define CONFIG_SYS_PCIE1_MEM_BUS 0xc0000000
-#define CONFIG_SYS_PCIE1_MEM_PHYS 0xc0000000
-#endif
-#define CONFIG_SYS_PCIE1_MEM_SIZE 0x20000000 /* 512M */
-#define CONFIG_SYS_PCIE1_IO_VIRT 0xffc20000
-#define CONFIG_SYS_PCIE1_IO_BUS 0x00000000
-#ifdef CONFIG_PHYS_64BIT
-#define CONFIG_SYS_PCIE1_IO_PHYS 0xfffc20000ull
-#else
-#define CONFIG_SYS_PCIE1_IO_PHYS 0xffc20000
-#endif
-#define CONFIG_SYS_PCIE1_IO_SIZE 0x00010000 /* 64k */
-
-#if defined(CONFIG_PCI)
-
-/*PCIE video card used*/
-#define VIDEO_IO_OFFSET CONFIG_SYS_PCIE1_IO_VIRT
-
-/* video */
-
-#if defined(CONFIG_VIDEO)
-#define CONFIG_BIOSEMU
-#define CONFIG_ATI_RADEON_FB
-#define CONFIG_VIDEO_LOGO
-#define CONFIG_SYS_ISA_IO_BASE_ADDRESS VIDEO_IO_OFFSET
-#endif
-
-#undef CONFIG_EEPRO100
-#undef CONFIG_TULIP
-
-#ifndef CONFIG_PCI_PNP
- #define PCI_ENET0_IOADDR CONFIG_SYS_PCIE3_IO_BUS
- #define PCI_ENET0_MEMADDR CONFIG_SYS_PCIE3_IO_BUS
- #define PCI_IDSEL_NUMBER 0x11 /* IDSEL = AD11 */
-#endif
-
-#define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */
-
-#ifdef CONFIG_SCSI_AHCI
-#define CONFIG_SATA_ULI5288
-#define CONFIG_SYS_SCSI_MAX_SCSI_ID 4
-#define CONFIG_SYS_SCSI_MAX_LUN 1
-#define CONFIG_SYS_SCSI_MAX_DEVICE (CONFIG_SYS_SCSI_MAX_SCSI_ID * CONFIG_SYS_SCSI_MAX_LUN)
-#endif /* SCSI */
-
-#endif /* CONFIG_PCI */
-
-#if defined(CONFIG_TSEC_ENET)
-
-#define CONFIG_MII_DEFAULT_TSEC 1 /* Allow unregistered phys */
-#define CONFIG_TSEC1 1
-#define CONFIG_TSEC1_NAME "eTSEC1"
-#define CONFIG_TSEC2 1
-#define CONFIG_TSEC2_NAME "eTSEC2"
-#define CONFIG_TSEC3 1
-#define CONFIG_TSEC3_NAME "eTSEC3"
-#define CONFIG_TSEC4 1
-#define CONFIG_TSEC4_NAME "eTSEC4"
-
-#define CONFIG_PIXIS_SGMII_CMD
-#define CONFIG_FSL_SGMII_RISER 1
-#define SGMII_RISER_PHY_OFFSET 0x1c
-
-#ifdef CONFIG_FSL_SGMII_RISER
-#define CONFIG_SYS_TBIPA_VALUE 0x10 /* avoid conflict with eTSEC4 paddr */
-#endif
-
-#define TSEC1_PHY_ADDR 0
-#define TSEC2_PHY_ADDR 1
-#define TSEC3_PHY_ADDR 2
-#define TSEC4_PHY_ADDR 3
-
-#define TSEC1_FLAGS (TSEC_GIGABIT | TSEC_REDUCED)
-#define TSEC2_FLAGS (TSEC_GIGABIT | TSEC_REDUCED)
-#define TSEC3_FLAGS (TSEC_GIGABIT | TSEC_REDUCED)
-#define TSEC4_FLAGS (TSEC_GIGABIT | TSEC_REDUCED)
-
-#define TSEC1_PHYIDX 0
-#define TSEC2_PHYIDX 0
-#define TSEC3_PHYIDX 0
-#define TSEC4_PHYIDX 0
-
-#define CONFIG_ETHPRIME "eTSEC1"
-#endif /* CONFIG_TSEC_ENET */
-
-/*
- * Environment
- */
-
-#if defined(CONFIG_SYS_RAMBOOT)
-
-#else
- #if CONFIG_SYS_MONITOR_BASE > 0xfff80000
- #define CONFIG_ENV_ADDR 0xfff80000
- #else
- #define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - CONFIG_ENV_SECT_SIZE)
- #endif
- #define CONFIG_ENV_SIZE 0x2000
- #define CONFIG_ENV_SECT_SIZE 0x20000 /* 128K (one sector) */
-#endif
-
-#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
-#define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
-
-/*
- * USB
- */
-
-#ifdef CONFIG_USB_EHCI_HCD
-#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
-#define CONFIG_PCI_EHCI_DEVICE 0
-#endif
-
-#undef CONFIG_WATCHDOG /* watchdog disabled */
-
-/*
- * Miscellaneous configurable options
- */
-#define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */
-
-/*
- * For booting Linux, the board info and command line data
- * have to be in the first 64 MB of memory, since this is
- * the maximum mapped by the Linux kernel during initialization.
- */
-#define CONFIG_SYS_BOOTMAPSZ (64 << 20) /* Initial Memory map for Linux*/
-#define CONFIG_SYS_BOOTM_LEN (64 << 20) /* Increase max gunzip size */
-
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */
-#endif
-
-/*
- * Environment Configuration
- */
-#if defined(CONFIG_TSEC_ENET)
-#define CONFIG_HAS_ETH0
-#define CONFIG_HAS_ETH1
-#define CONFIG_HAS_ETH2
-#define CONFIG_HAS_ETH3
-#endif
-
-#define CONFIG_IPADDR 192.168.1.254
-
-#define CONFIG_HOSTNAME "unknown"
-#define CONFIG_ROOTPATH "/opt/nfsroot"
-#define CONFIG_BOOTFILE "uImage"
-#define CONFIG_UBOOTPATH u-boot.bin /* U-Boot image on TFTP server */
-
-#define CONFIG_SERVERIP 192.168.1.1
-#define CONFIG_GATEWAYIP 192.168.1.1
-#define CONFIG_NETMASK 255.255.255.0
-
-/* default location for tftp and bootm */
-#define CONFIG_LOADADDR 1000000
-
-#define CONFIG_EXTRA_ENV_SETTINGS \
-"hwconfig=fsl_ddr:ctlr_intlv=bank,bank_intlv=cs0_cs1,ecc=off\0" \
-"netdev=eth0\0" \
-"uboot=" __stringify(CONFIG_UBOOTPATH) "\0" \
-"tftpflash=tftpboot $loadaddr $uboot; " \
- "protect off " __stringify(CONFIG_SYS_TEXT_BASE) \
- " +$filesize; " \
- "erase " __stringify(CONFIG_SYS_TEXT_BASE) \
- " +$filesize; " \
- "cp.b $loadaddr " __stringify(CONFIG_SYS_TEXT_BASE) \
- " $filesize; " \
- "protect on " __stringify(CONFIG_SYS_TEXT_BASE) \
- " +$filesize; " \
- "cmp.b $loadaddr " __stringify(CONFIG_SYS_TEXT_BASE) \
- " $filesize\0" \
-"consoledev=ttyS0\0" \
-"ramdiskaddr=2000000\0" \
-"ramdiskfile=8572ds/ramdisk.uboot\0" \
-"fdtaddr=1e00000\0" \
-"fdtfile=8572ds/mpc8572ds.dtb\0" \
-"bdev=sda3\0"
-
-#define CONFIG_HDBOOT \
- "setenv bootargs root=/dev/$bdev rw " \
- "console=$consoledev,$baudrate $othbootargs;" \
- "tftp $loadaddr $bootfile;" \
- "tftp $fdtaddr $fdtfile;" \
- "bootm $loadaddr - $fdtaddr"
-
-#define CONFIG_NFSBOOTCOMMAND \
- "setenv bootargs root=/dev/nfs rw " \
- "nfsroot=$serverip:$rootpath " \
- "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \
- "console=$consoledev,$baudrate $othbootargs;" \
- "tftp $loadaddr $bootfile;" \
- "tftp $fdtaddr $fdtfile;" \
- "bootm $loadaddr - $fdtaddr"
-
-#define CONFIG_RAMBOOTCOMMAND \
- "setenv bootargs root=/dev/ram rw " \
- "console=$consoledev,$baudrate $othbootargs;" \
- "tftp $ramdiskaddr $ramdiskfile;" \
- "tftp $loadaddr $bootfile;" \
- "tftp $fdtaddr $fdtfile;" \
- "bootm $loadaddr $ramdiskaddr $fdtaddr"
-
-#define CONFIG_BOOTCOMMAND CONFIG_HDBOOT
-
-#endif /* __CONFIG_H */
projects / platform / kernel / u-boot.git / blobdiff