+++ /dev/null
-/* SPDX-License-Identifier: GPL-2.0+ */
-/*
- * Copyright (C) Freescale Semiconductor, Inc. 2006.
- */
-
-/*
- MPC8349E-mITX and MPC8349E-mITX-GP board configuration file
-
- Memory map:
-
- 0x0000_0000-0x0FFF_FFFF DDR SDRAM (256 MB)
- 0x8000_0000-0x9FFF_FFFF PCI1 memory space (512 MB)
- 0xA000_0000-0xBFFF_FFFF PCI2 memory space (512 MB)
- 0xE000_0000-0xEFFF_FFFF IMMR (1 MB)
- 0xE200_0000-0xE2FF_FFFF PCI1 I/O space (16 MB)
- 0xE300_0000-0xE3FF_FFFF PCI2 I/O space (16 MB)
- 0xF000_0000-0xF000_FFFF Compact Flash (MPC8349E-mITX only)
- 0xF001_0000-0xF001_FFFF Local bus expansion slot
- 0xF800_0000-0xF801_FFFF Vitesse 7385 Parallel Interface (MPC8349E-mITX only)
- 0xFE00_0000-0xFE7F_FFFF First 8MB bank of Flash memory
- 0xFE80_0000-0xFEFF_FFFF Second 8MB bank of Flash memory (MPC8349E-mITX only)
-
- I2C address list:
- Align. Board
- Bus Addr Part No. Description Length Location
- ----------------------------------------------------------------
- I2C0 0x50 M24256-BWMN6P Board EEPROM 2 U64
-
- I2C1 0x20 PCF8574 I2C Expander 0 U8
- I2C1 0x21 PCF8574 I2C Expander 0 U10
- I2C1 0x38 PCF8574A I2C Expander 0 U8
- I2C1 0x39 PCF8574A I2C Expander 0 U10
- I2C1 0x51 (DDR) DDR EEPROM 1 U1
- I2C1 0x68 DS1339 RTC 1 U68
-
- Note that a given board has *either* a pair of 8574s or a pair of 8574As.
-*/
-
-#ifndef __CONFIG_H
-#define __CONFIG_H
-
-/*
- * High Level Configuration Options
- */
-#define CONFIG_SYS_IMMR 0xE0000000 /* The IMMR is relocated to here */
-
-#define CONFIG_MISC_INIT_F
-
-/*
- * On-board devices
- */
-
-#ifdef CONFIG_TARGET_MPC8349ITX
-/* The CF card interface on the back of the board */
-#define CONFIG_COMPACT_FLASH
-#define CONFIG_VSC7385_ENET /* VSC7385 ethernet support */
-#define CONFIG_SYS_USB_HOST /* use the EHCI USB controller */
-#endif
-
-#define CONFIG_RTC_DS1337
-#define CONFIG_SYS_I2C
-
-/*
- * Device configurations
- */
-
-/* I2C */
-#ifdef CONFIG_SYS_I2C
-#define CONFIG_SYS_I2C_FSL
-#define CONFIG_SYS_FSL_I2C_SPEED 400000
-#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F
-#define CONFIG_SYS_FSL_I2C_OFFSET 0x3000
-#define CONFIG_SYS_FSL_I2C2_SPEED 400000
-#define CONFIG_SYS_FSL_I2C2_SLAVE 0x7F
-#define CONFIG_SYS_FSL_I2C2_OFFSET 0x3100
-
-#define CONFIG_SYS_SPD_BUS_NUM 1 /* The I2C bus for SPD */
-#define CONFIG_SYS_RTC_BUS_NUM 1 /* The I2C bus for RTC */
-
-#define CONFIG_SYS_I2C_8574_ADDR1 0x20 /* I2C1, PCF8574 */
-#define CONFIG_SYS_I2C_8574_ADDR2 0x21 /* I2C1, PCF8574 */
-#define CONFIG_SYS_I2C_8574A_ADDR1 0x38 /* I2C1, PCF8574A */
-#define CONFIG_SYS_I2C_8574A_ADDR2 0x39 /* I2C1, PCF8574A */
-#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 /* I2C0, Board EEPROM */
-#define CONFIG_SYS_I2C_RTC_ADDR 0x68 /* I2C1, DS1339 RTC*/
-#define SPD_EEPROM_ADDRESS 0x51 /* I2C1, DDR */
-
-/* Don't probe these addresses: */
-#define CONFIG_SYS_I2C_NOPROBES { {1, CONFIG_SYS_I2C_8574_ADDR1}, \
- {1, CONFIG_SYS_I2C_8574_ADDR2}, \
- {1, CONFIG_SYS_I2C_8574A_ADDR1}, \
- {1, CONFIG_SYS_I2C_8574A_ADDR2} }
-/* Bit definitions for the 8574[A] I2C expander */
- /* Board revision, 00=0.0, 01=0.1, 10=1.0 */
-#define I2C_8574_REVISION 0x03
-#define I2C_8574_CF 0x08 /* 1=Compact flash absent, 0=present */
-#define I2C_8574_MPCICLKRN 0x10 /* MiniPCI Clk Run */
-#define I2C_8574_PCI66 0x20 /* 0=33MHz PCI, 1=66MHz PCI */
-#define I2C_8574_FLASHSIDE 0x40 /* 0=Reset vector from U4, 1=from U7*/
-
-#endif
-
-/* Compact Flash */
-#ifdef CONFIG_COMPACT_FLASH
-
-#define CONFIG_SYS_IDE_MAXBUS 1
-#define CONFIG_SYS_IDE_MAXDEVICE 1
-
-#define CONFIG_SYS_ATA_IDE0_OFFSET 0x0000
-#define CONFIG_SYS_ATA_BASE_ADDR CONFIG_SYS_CF_BASE
-#define CONFIG_SYS_ATA_DATA_OFFSET 0x0000
-#define CONFIG_SYS_ATA_REG_OFFSET 0
-#define CONFIG_SYS_ATA_ALT_OFFSET 0x0200
-#define CONFIG_SYS_ATA_STRIDE 2
-
-/* If a CF card is not inserted, time out quickly */
-#define ATA_RESET_TIME 1
-
-#endif
-
-/*
- * SATA
- */
-#ifdef CONFIG_SATA_SIL3114
-
-#define CONFIG_SYS_SATA_MAX_DEVICE 4
-#define CONFIG_LBA48
-
-#endif
-
-#ifdef CONFIG_SYS_USB_HOST
-/*
- * Support USB
- */
-#define CONFIG_USB_EHCI_FSL
-
-/* Current USB implementation supports the only USB controller,
- * so we have to choose between the MPH or the DR ones */
-#if 1
-#define CONFIG_HAS_FSL_MPH_USB
-#else
-#define CONFIG_HAS_FSL_DR_USB
-#endif
-
-#endif
-
-/*
- * DDR Setup
- */
-#define CONFIG_SYS_DDR_BASE 0x00000000 /* DDR is system memory*/
-#define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_BASE
-#define CONFIG_SYS_DDR_SDRAM_BASE CONFIG_SYS_DDR_BASE
-#define CONFIG_SYS_83XX_DDR_USES_CS0
-#define CONFIG_SYS_MEMTEST_START 0x1000 /* memtest region */
-#define CONFIG_SYS_MEMTEST_END 0x2000
-
-#define CONFIG_SYS_DDR_SDRAM_CLK_CNTL (DDR_SDRAM_CLK_CNTL_SS_EN \
- | DDR_SDRAM_CLK_CNTL_CLK_ADJUST_075)
-
-#define CONFIG_VERY_BIG_RAM
-#define CONFIG_MAX_MEM_MAPPED ((phys_size_t)256 << 20)
-
-#ifdef CONFIG_SYS_I2C
-#define CONFIG_SPD_EEPROM /* use SPD EEPROM for DDR setup*/
-#endif
-
-/* No SPD? Then manually set up DDR parameters */
-#ifndef CONFIG_SPD_EEPROM
- #define CONFIG_SYS_DDR_SIZE 256 /* Mb */
- #define CONFIG_SYS_DDR_CS0_CONFIG (CSCONFIG_EN \
- | CSCONFIG_ROW_BIT_13 \
- | CSCONFIG_COL_BIT_10)
-
- #define CONFIG_SYS_DDR_TIMING_1 0x26242321
- #define CONFIG_SYS_DDR_TIMING_2 0x00000800 /* P9-45, may need tuning */
-#endif
-
-/*
- *Flash on the Local Bus
- */
-
-#define CONFIG_SYS_FLASH_BASE 0xFE000000 /* start of FLASH */
-#define CONFIG_SYS_FLASH_EMPTY_INFO
-/* 127 64KB sectors + 8 8KB sectors per device */
-#define CONFIG_SYS_MAX_FLASH_SECT 135
-#define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */
-#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */
-#define CONFIG_SYS_FLASH_CFI_WIDTH FLASH_CFI_16BIT
-
-/* The ITX has two flash chips, but the ITX-GP has only one. To support both
-boards, we say we have two, but don't display a message if we find only one. */
-#define CONFIG_SYS_FLASH_QUIET_TEST
-#define CONFIG_SYS_MAX_FLASH_BANKS 2 /* number of banks */
-#define CONFIG_SYS_FLASH_BANKS_LIST \
- {CONFIG_SYS_FLASH_BASE, CONFIG_SYS_FLASH_BASE + 0x800000}
-#define CONFIG_SYS_FLASH_SIZE 16 /* FLASH size in MB */
-
-/* Vitesse 7385 */
-
-#ifdef CONFIG_VSC7385_ENET
-
-#define CONFIG_TSEC2
-
-/* The flash address and size of the VSC7385 firmware image */
-#define CONFIG_VSC7385_IMAGE 0xFEFFE000
-#define CONFIG_VSC7385_IMAGE_SIZE 8192
-
-#endif
-
-/*
- * BRx, ORx, LBLAWBARx, and LBLAWARx
- */
-
-/* Flash */
-
-#define CONFIG_SYS_BR0_PRELIM (CONFIG_SYS_FLASH_BASE \
- | BR_PS_16 \
- | BR_MS_GPCM \
- | BR_V)
-#define CONFIG_SYS_OR0_PRELIM (MEG_TO_AM(CONFIG_SYS_FLASH_SIZE) \
- | OR_UPM_XAM \
- | OR_GPCM_CSNT \
- | OR_GPCM_ACS_DIV2 \
- | OR_GPCM_XACS \
- | OR_GPCM_SCY_15 \
- | OR_GPCM_TRLX_SET \
- | OR_GPCM_EHTR_SET \
- | OR_GPCM_EAD)
-#define CONFIG_SYS_LBLAWBAR0_PRELIM CONFIG_SYS_FLASH_BASE
-#define CONFIG_SYS_LBLAWAR0_PRELIM (LBLAWAR_EN | LBLAWAR_16MB)
-
-/* Vitesse 7385 */
-
-#define CONFIG_SYS_VSC7385_BASE 0xF8000000
-
-#ifdef CONFIG_VSC7385_ENET
-
-#define CONFIG_SYS_BR1_PRELIM (CONFIG_SYS_VSC7385_BASE \
- | BR_PS_8 \
- | BR_MS_GPCM \
- | BR_V)
-#define CONFIG_SYS_OR1_PRELIM (OR_AM_128KB \
- | OR_GPCM_CSNT \
- | OR_GPCM_XACS \
- | OR_GPCM_SCY_15 \
- | OR_GPCM_SETA \
- | OR_GPCM_TRLX_SET \
- | OR_GPCM_EHTR_SET \
- | OR_GPCM_EAD)
-
-#define CONFIG_SYS_LBLAWBAR1_PRELIM CONFIG_SYS_VSC7385_BASE
-#define CONFIG_SYS_LBLAWAR1_PRELIM (LBLAWAR_EN | LBLAWAR_128KB)
-
-#endif
-
-/* LED */
-
-#define CONFIG_SYS_LED_BASE 0xF9000000
-#define CONFIG_SYS_BR2_PRELIM (CONFIG_SYS_LED_BASE \
- | BR_PS_8 \
- | BR_MS_GPCM \
- | BR_V)
-#define CONFIG_SYS_OR2_PRELIM (OR_AM_2MB \
- | OR_GPCM_CSNT \
- | OR_GPCM_ACS_DIV2 \
- | OR_GPCM_XACS \
- | OR_GPCM_SCY_9 \
- | OR_GPCM_TRLX_SET \
- | OR_GPCM_EHTR_SET \
- | OR_GPCM_EAD)
-
-/* Compact Flash */
-
-#ifdef CONFIG_COMPACT_FLASH
-
-#define CONFIG_SYS_CF_BASE 0xF0000000
-
-#define CONFIG_SYS_BR3_PRELIM (CONFIG_SYS_CF_BASE \
- | BR_PS_16 \
- | BR_MS_UPMA \
- | BR_V)
-#define CONFIG_SYS_OR3_PRELIM (OR_UPM_AM | OR_UPM_BI)
-
-#define CONFIG_SYS_LBLAWBAR3_PRELIM CONFIG_SYS_CF_BASE
-#define CONFIG_SYS_LBLAWAR3_PRELIM (LBLAWAR_EN | LBLAWAR_64KB)
-
-#endif
-
-/*
- * U-Boot memory configuration
- */
-#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */
-
-#if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE)
-#define CONFIG_SYS_RAMBOOT
-#else
-#undef CONFIG_SYS_RAMBOOT
-#endif
-
-#define CONFIG_SYS_INIT_RAM_LOCK
-#define CONFIG_SYS_INIT_RAM_ADDR 0xFD000000 /* Initial RAM addr */
-#define CONFIG_SYS_INIT_RAM_SIZE 0x1000 /* Size of used area in RAM*/
-
-#define CONFIG_SYS_GBL_DATA_OFFSET \
- (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
-#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
-
-/* CONFIG_SYS_MONITOR_LEN must be a multiple of CONFIG_ENV_SECT_SIZE */
-#define CONFIG_SYS_MONITOR_LEN (512 * 1024) /* Reserve 512 kB for Mon */
-#define CONFIG_SYS_MALLOC_LEN (256 * 1024) /* Reserved for malloc */
-
-/*
- * Local Bus LCRR and LBCR regs
- * LCRR: DLL bypass, Clock divider is 4
- * External Local Bus rate is
- * CLKIN * HRCWL_CSB_TO_CLKIN / HRCWL_LCL_BUS_TO_SCB_CLK / LCRR_CLKDIV
- */
-#define CONFIG_SYS_LCRR_DBYP LCRR_DBYP
-#define CONFIG_SYS_LCRR_CLKDIV LCRR_CLKDIV_4
-#define CONFIG_SYS_LBC_LBCR 0x00000000
-
- /* LB sdram refresh timer, about 6us */
-#define CONFIG_SYS_LBC_LSRT 0x32000000
- /* LB refresh timer prescal, 266MHz/32*/
-#define CONFIG_SYS_LBC_MRTPR 0x20000000
-
-/*
- * Serial Port
- */
-#define CONFIG_SYS_NS16550_SERIAL
-#define CONFIG_SYS_NS16550_REG_SIZE 1
-#define CONFIG_SYS_NS16550_CLK get_bus_freq(0)
-
-#define CONFIG_SYS_BAUDRATE_TABLE \
- {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 115200}
-
-#define CONSOLE ttyS0
-
-#define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_IMMR + 0x4500)
-#define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_IMMR + 0x4600)
-
-/*
- * PCI
- */
-#ifdef CONFIG_PCI
-#define CONFIG_PCI_INDIRECT_BRIDGE
-
-#define CONFIG_MPC83XX_PCI2
-
-/*
- * General PCI
- * Addresses are mapped 1-1.
- */
-#define CONFIG_SYS_PCI1_MEM_BASE 0x80000000
-#define CONFIG_SYS_PCI1_MEM_PHYS CONFIG_SYS_PCI1_MEM_BASE
-#define CONFIG_SYS_PCI1_MEM_SIZE 0x10000000 /* 256M */
-#define CONFIG_SYS_PCI1_MMIO_BASE \
- (CONFIG_SYS_PCI1_MEM_BASE + CONFIG_SYS_PCI1_MEM_SIZE)
-#define CONFIG_SYS_PCI1_MMIO_PHYS CONFIG_SYS_PCI1_MMIO_BASE
-#define CONFIG_SYS_PCI1_MMIO_SIZE 0x10000000 /* 256M */
-#define CONFIG_SYS_PCI1_IO_BASE 0x00000000
-#define CONFIG_SYS_PCI1_IO_PHYS 0xE2000000
-#define CONFIG_SYS_PCI1_IO_SIZE 0x01000000 /* 16M */
-
-#ifdef CONFIG_MPC83XX_PCI2
-#define CONFIG_SYS_PCI2_MEM_BASE \
- (CONFIG_SYS_PCI1_MMIO_BASE + CONFIG_SYS_PCI1_MMIO_SIZE)
-#define CONFIG_SYS_PCI2_MEM_PHYS CONFIG_SYS_PCI2_MEM_BASE
-#define CONFIG_SYS_PCI2_MEM_SIZE 0x10000000 /* 256M */
-#define CONFIG_SYS_PCI2_MMIO_BASE \
- (CONFIG_SYS_PCI2_MEM_BASE + CONFIG_SYS_PCI2_MEM_SIZE)
-#define CONFIG_SYS_PCI2_MMIO_PHYS CONFIG_SYS_PCI2_MMIO_BASE
-#define CONFIG_SYS_PCI2_MMIO_SIZE 0x10000000 /* 256M */
-#define CONFIG_SYS_PCI2_IO_BASE 0x00000000
-#define CONFIG_SYS_PCI2_IO_PHYS \
- (CONFIG_SYS_PCI1_IO_PHYS + CONFIG_SYS_PCI1_IO_SIZE)
-#define CONFIG_SYS_PCI2_IO_SIZE 0x01000000 /* 16M */
-#endif
-
-#ifndef CONFIG_PCI_PNP
- #define PCI_ENET0_IOADDR 0x00000000
- #define PCI_ENET0_MEMADDR CONFIG_SYS_PCI2_MEM_BASE
- #define PCI_IDSEL_NUMBER 0x0f /* IDSEL = AD15 */
-#endif
-
-#define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */
-
-#endif
-
-/* TSEC */
-
-#ifdef CONFIG_TSEC_ENET
-#define CONFIG_TSEC1
-
-#ifdef CONFIG_TSEC1
-#define CONFIG_HAS_ETH0
-#define CONFIG_TSEC1_NAME "TSEC0"
-#define CONFIG_SYS_TSEC1_OFFSET 0x24000
-#define TSEC1_PHY_ADDR 0x1c /* VSC8201 uses address 0x1c */
-#define TSEC1_PHYIDX 0
-#define TSEC1_FLAGS TSEC_GIGABIT
-#endif
-
-#ifdef CONFIG_TSEC2
-#define CONFIG_HAS_ETH1
-#define CONFIG_TSEC2_NAME "TSEC1"
-#define CONFIG_SYS_TSEC2_OFFSET 0x25000
-
-#define TSEC2_PHY_ADDR 4
-#define TSEC2_PHYIDX 0
-#define TSEC2_FLAGS TSEC_GIGABIT
-#endif
-
-#define CONFIG_ETHPRIME "Freescale TSEC"
-
-#endif
-
-/*
- * Environment
- */
-#define CONFIG_ENV_OVERWRITE
-
-#ifndef CONFIG_SYS_RAMBOOT
- #define CONFIG_ENV_ADDR \
- (CONFIG_SYS_MONITOR_BASE + CONFIG_SYS_MONITOR_LEN)
- #define CONFIG_ENV_SECT_SIZE 0x10000 /* 64K (one sector) for environment */
- #define CONFIG_ENV_SIZE 0x2000
-#else
- #define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - 0x1000)
- #define CONFIG_ENV_SIZE 0x2000
-#endif
-
-#define CONFIG_LOADS_ECHO /* echo on for serial download */
-#define CONFIG_SYS_LOADS_BAUD_CHANGE /* allow baudrate change */
-
-/*
- * BOOTP options
- */
-#define CONFIG_BOOTP_BOOTFILESIZE
-
-/* Watchdog */
-#undef CONFIG_WATCHDOG /* watchdog disabled */
-
-/*
- * Miscellaneous configurable options
- */
-
-#define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */
-#define CONFIG_LOADADDR 800000 /* default location for tftp and bootm */
-
-/*
- * For booting Linux, the board info and command line data
- * have to be in the first 256 MB of memory, since this is
- * the maximum mapped by the Linux kernel during initialization.
- */
- /* Initial Memory map for Linux*/
-#define CONFIG_SYS_BOOTMAPSZ (256 << 20)
-#define CONFIG_SYS_BOOTM_LEN (64 << 20) /* Increase max gunzip size */
-
-/*
- * System performance
- */
-#define CONFIG_SYS_ACR_PIPE_DEP 3 /* Arbiter pipeline depth (0-3) */
-#define CONFIG_SYS_ACR_RPTCNT 3 /* Arbiter repeat count (0-7) */
-#define CONFIG_SYS_SPCR_TSEC1EP 3 /* TSEC1 emergency priority (0-3) */
-#define CONFIG_SYS_SPCR_TSEC2EP 3 /* TSEC2 emergency priority (0-3) */
-#define CONFIG_SYS_SCCR_TSEC1CM 1 /* TSEC1 clock mode (0-3) */
-#define CONFIG_SYS_SCCR_TSEC2CM 1 /* TSEC2 & I2C0 clock mode (0-3) */
-#define CONFIG_SYS_SCCR_USBMPHCM 3 /* USB MPH controller's clock */
-#define CONFIG_SYS_SCCR_USBDRCM 0 /* USB DR controller's clock */
-
-/*
- * System IO Config
- */
-/* Needed for gigabit to work on TSEC 1 */
-#define CONFIG_SYS_SICRH SICRH_TSOBI1
- /* USB DR as device + USB MPH as host */
-#define CONFIG_SYS_SICRL (SICRL_LDP_A | SICRL_USB1)
-
-#define CONFIG_SYS_HID0_INIT 0x00000000
-#define CONFIG_SYS_HID0_FINAL HID0_ENABLE_INSTRUCTION_CACHE
-
-#define CONFIG_SYS_HID2 HID2_HBE
-#define CONFIG_HIGH_BATS 1 /* High BATs supported */
-
-/* DDR */
-#define CONFIG_SYS_IBAT0L (CONFIG_SYS_SDRAM_BASE \
- | BATL_PP_RW \
- | BATL_MEMCOHERENCE)
-#define CONFIG_SYS_IBAT0U (CONFIG_SYS_SDRAM_BASE \
- | BATU_BL_256M \
- | BATU_VS \
- | BATU_VP)
-
-/* PCI */
-#ifdef CONFIG_PCI
-#define CONFIG_SYS_IBAT1L (CONFIG_SYS_PCI1_MEM_BASE \
- | BATL_PP_RW \
- | BATL_MEMCOHERENCE)
-#define CONFIG_SYS_IBAT1U (CONFIG_SYS_PCI1_MEM_BASE \
- | BATU_BL_256M \
- | BATU_VS \
- | BATU_VP)
-#define CONFIG_SYS_IBAT2L (CONFIG_SYS_PCI1_MMIO_BASE \
- | BATL_PP_RW \
- | BATL_CACHEINHIBIT \
- | BATL_GUARDEDSTORAGE)
-#define CONFIG_SYS_IBAT2U (CONFIG_SYS_PCI1_MMIO_BASE \
- | BATU_BL_256M \
- | BATU_VS \
- | BATU_VP)
-#else
-#define CONFIG_SYS_IBAT1L 0
-#define CONFIG_SYS_IBAT1U 0
-#define CONFIG_SYS_IBAT2L 0
-#define CONFIG_SYS_IBAT2U 0
-#endif
-
-#ifdef CONFIG_MPC83XX_PCI2
-#define CONFIG_SYS_IBAT3L (CONFIG_SYS_PCI2_MEM_BASE \
- | BATL_PP_RW \
- | BATL_MEMCOHERENCE)
-#define CONFIG_SYS_IBAT3U (CONFIG_SYS_PCI2_MEM_BASE \
- | BATU_BL_256M \
- | BATU_VS \
- | BATU_VP)
-#define CONFIG_SYS_IBAT4L (CONFIG_SYS_PCI2_MMIO_BASE \
- | BATL_PP_RW \
- | BATL_CACHEINHIBIT \
- | BATL_GUARDEDSTORAGE)
-#define CONFIG_SYS_IBAT4U (CONFIG_SYS_PCI2_MMIO_BASE \
- | BATU_BL_256M \
- | BATU_VS \
- | BATU_VP)
-#else
-#define CONFIG_SYS_IBAT3L 0
-#define CONFIG_SYS_IBAT3U 0
-#define CONFIG_SYS_IBAT4L 0
-#define CONFIG_SYS_IBAT4U 0
-#endif
-
-/* IMMRBAR @ 0xE0000000, PCI IO @ 0xE2000000 & BCSR @ 0xE2400000 */
-#define CONFIG_SYS_IBAT5L (CONFIG_SYS_IMMR \
- | BATL_PP_RW \
- | BATL_CACHEINHIBIT \
- | BATL_GUARDEDSTORAGE)
-#define CONFIG_SYS_IBAT5U (CONFIG_SYS_IMMR \
- | BATU_BL_256M \
- | BATU_VS \
- | BATU_VP)
-
-/* SDRAM @ 0xF0000000, stack in DCACHE 0xFDF00000 & FLASH @ 0xFE000000 */
-#define CONFIG_SYS_IBAT6L (0xF0000000 \
- | BATL_PP_RW \
- | BATL_MEMCOHERENCE \
- | BATL_GUARDEDSTORAGE)
-#define CONFIG_SYS_IBAT6U (0xF0000000 \
- | BATU_BL_256M \
- | BATU_VS \
- | BATU_VP)
-
-#define CONFIG_SYS_IBAT7L 0
-#define CONFIG_SYS_IBAT7U 0
-
-#define CONFIG_SYS_DBAT0L CONFIG_SYS_IBAT0L
-#define CONFIG_SYS_DBAT0U CONFIG_SYS_IBAT0U
-#define CONFIG_SYS_DBAT1L CONFIG_SYS_IBAT1L
-#define CONFIG_SYS_DBAT1U CONFIG_SYS_IBAT1U
-#define CONFIG_SYS_DBAT2L CONFIG_SYS_IBAT2L
-#define CONFIG_SYS_DBAT2U CONFIG_SYS_IBAT2U
-#define CONFIG_SYS_DBAT3L CONFIG_SYS_IBAT3L
-#define CONFIG_SYS_DBAT3U CONFIG_SYS_IBAT3U
-#define CONFIG_SYS_DBAT4L CONFIG_SYS_IBAT4L
-#define CONFIG_SYS_DBAT4U CONFIG_SYS_IBAT4U
-#define CONFIG_SYS_DBAT5L CONFIG_SYS_IBAT5L
-#define CONFIG_SYS_DBAT5U CONFIG_SYS_IBAT5U
-#define CONFIG_SYS_DBAT6L CONFIG_SYS_IBAT6L
-#define CONFIG_SYS_DBAT6U CONFIG_SYS_IBAT6U
-#define CONFIG_SYS_DBAT7L CONFIG_SYS_IBAT7L
-#define CONFIG_SYS_DBAT7U CONFIG_SYS_IBAT7U
-
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_KGDB_BAUDRATE 230400 /* speed of kgdb serial port */
-#endif
-
-/*
- * Environment Configuration
- */
-#define CONFIG_ENV_OVERWRITE
-
-#define CONFIG_NETDEV "eth0"
-
-/* Default path and filenames */
-#define CONFIG_ROOTPATH "/nfsroot/rootfs"
-#define CONFIG_BOOTFILE "uImage"
- /* U-Boot image on TFTP server */
-#define CONFIG_UBOOTPATH "u-boot.bin"
-
-#ifdef CONFIG_TARGET_MPC8349ITX
-#define CONFIG_FDTFILE "mpc8349emitx.dtb"
-#else
-#define CONFIG_FDTFILE "mpc8349emitxgp.dtb"
-#endif
-
-
-#define CONFIG_EXTRA_ENV_SETTINGS \
- "console=" __stringify(CONSOLE) "\0" \
- "netdev=" CONFIG_NETDEV "\0" \
- "uboot=" CONFIG_UBOOTPATH "\0" \
- "tftpflash=tftpboot $loadaddr $uboot; " \
- "protect off " __stringify(CONFIG_SYS_TEXT_BASE) \
- " +$filesize; " \
- "erase " __stringify(CONFIG_SYS_TEXT_BASE) \
- " +$filesize; " \
- "cp.b $loadaddr " __stringify(CONFIG_SYS_TEXT_BASE) \
- " $filesize; " \
- "protect on " __stringify(CONFIG_SYS_TEXT_BASE) \
- " +$filesize; " \
- "cmp.b $loadaddr " __stringify(CONFIG_SYS_TEXT_BASE) \
- " $filesize\0" \
- "fdtaddr=780000\0" \
- "fdtfile=" CONFIG_FDTFILE "\0"
-
-#define CONFIG_NFSBOOTCOMMAND \
- "setenv bootargs root=/dev/nfs rw nfsroot=$serverip:$rootpath" \
- " ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off "\
- " console=$console,$baudrate $othbootargs; " \
- "tftp $loadaddr $bootfile;" \
- "tftp $fdtaddr $fdtfile;" \
- "bootm $loadaddr - $fdtaddr"
-
-#define CONFIG_RAMBOOTCOMMAND \
- "setenv bootargs root=/dev/ram rw" \
- " console=$console,$baudrate $othbootargs; " \
- "tftp $ramdiskaddr $ramdiskfile;" \
- "tftp $loadaddr $bootfile;" \
- "tftp $fdtaddr $fdtfile;" \
- "bootm $loadaddr $ramdiskaddr $fdtaddr"
-
-#endif
projects / platform / kernel / u-boot.git / blobdiff