+++ /dev/null
-/* SPDX-License-Identifier: GPL-2.0+ */
-/*
- * (C) Copyright 2006-2010
- * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
- */
-
-/*
- * mpc8349emds board configuration file
- *
- */
-
-#ifndef __CONFIG_H
-#define __CONFIG_H
-
-/*
- * High Level Configuration Options
- */
-#define CONFIG_E300 1 /* E300 Family */
-
-#undef CONFIG_SYS_DRAM_TEST /* memory test, takes time */
-
-/*
- * DDR Setup
- */
-#define CONFIG_DDR_ECC /* support DDR ECC function */
-#define CONFIG_DDR_ECC_CMD /* use DDR ECC user commands */
-#define CONFIG_SPD_EEPROM /* use SPD EEPROM for DDR setup*/
-
-/*
- * SYS_FSL_DDR2 is selected in Kconfig to use unified DDR driver
- * unselect it to use old spd_sdram.c
- */
-#define CONFIG_SYS_SPD_BUS_NUM 0
-#define SPD_EEPROM_ADDRESS1 0x52
-#define SPD_EEPROM_ADDRESS2 0x51
-#define CONFIG_DIMM_SLOTS_PER_CTLR 2
-#define CONFIG_CHIP_SELECTS_PER_CTRL (2 * CONFIG_DIMM_SLOTS_PER_CTLR)
-#define CONFIG_ECC_INIT_VIA_DDRCONTROLLER
-#define CONFIG_MEM_INIT_VALUE 0xDeadBeef
-
-/*
- * 32-bit data path mode.
- *
- * Please note that using this mode for devices with the real density of 64-bit
- * effectively reduces the amount of available memory due to the effect of
- * wrapping around while translating address to row/columns, for example in the
- * 256MB module the upper 128MB get aliased with contents of the lower
- * 128MB); normally this define should be used for devices with real 32-bit
- * data path.
- */
-#undef CONFIG_DDR_32BIT
-
-#define CONFIG_SYS_SDRAM_BASE 0x00000000 /* DDR is system memory*/
-#define CONFIG_SYS_DDR_SDRAM_CLK_CNTL (DDR_SDRAM_CLK_CNTL_SS_EN \
- | DDR_SDRAM_CLK_CNTL_CLK_ADJUST_05)
-#undef CONFIG_DDR_2T_TIMING
-
-/*
- * DDRCDR - DDR Control Driver Register
- */
-#define CONFIG_SYS_DDRCDR_VALUE 0x80080001
-
-#if defined(CONFIG_SPD_EEPROM)
-/*
- * Determine DDR configuration from I2C interface.
- */
-#define SPD_EEPROM_ADDRESS 0x51 /* DDR DIMM */
-#else
-/*
- * Manually set up DDR parameters
- */
-#define CONFIG_SYS_DDR_SIZE 256 /* MB */
-#if defined(CONFIG_DDR_II)
-#define CONFIG_SYS_DDRCDR 0x80080001
-#define CONFIG_SYS_DDR_CS2_BNDS 0x0000000f
-#define CONFIG_SYS_DDR_CS2_CONFIG 0x80330102
-#define CONFIG_SYS_DDR_TIMING_0 0x00220802
-#define CONFIG_SYS_DDR_TIMING_1 0x38357322
-#define CONFIG_SYS_DDR_TIMING_2 0x2f9048c8
-#define CONFIG_SYS_DDR_TIMING_3 0x00000000
-#define CONFIG_SYS_DDR_CLK_CNTL 0x02000000
-#define CONFIG_SYS_DDR_MODE 0x47d00432
-#define CONFIG_SYS_DDR_MODE2 0x8000c000
-#define CONFIG_SYS_DDR_INTERVAL 0x03cf0080
-#define CONFIG_SYS_DDR_SDRAM_CFG 0x43000000
-#define CONFIG_SYS_DDR_SDRAM_CFG2 0x00401000
-#else
-#define CONFIG_SYS_DDR_CS2_CONFIG (CSCONFIG_EN \
- | CSCONFIG_ROW_BIT_13 \
- | CSCONFIG_COL_BIT_10)
-#define CONFIG_SYS_DDR_TIMING_1 0x36332321
-#define CONFIG_SYS_DDR_TIMING_2 0x00000800 /* P9-45,may need tuning */
-#define CONFIG_SYS_DDR_CONTROL 0xc2000000 /* unbuffered,no DYN_PWR */
-#define CONFIG_SYS_DDR_INTERVAL 0x04060100 /* autocharge,no open page */
-
-#if defined(CONFIG_DDR_32BIT)
-/* set burst length to 8 for 32-bit data path */
- /* DLL,normal,seq,4/2.5, 8 burst len */
-#define CONFIG_SYS_DDR_MODE 0x00000023
-#else
-/* the default burst length is 4 - for 64-bit data path */
- /* DLL,normal,seq,4/2.5, 4 burst len */
-#define CONFIG_SYS_DDR_MODE 0x00000022
-#endif
-#endif
-#endif
-
-/*
- * SDRAM on the Local Bus
- */
-#define CONFIG_SYS_LBC_SDRAM_BASE 0xF0000000 /* Localbus SDRAM */
-#define CONFIG_SYS_LBC_SDRAM_SIZE 64 /* LBC SDRAM is 64MB */
-
-/*
- * FLASH on the Local Bus
- */
-#define CONFIG_SYS_FLASH_BASE 0xFE000000 /* start of FLASH */
-#define CONFIG_SYS_FLASH_SIZE 32 /* max flash size in MB */
-
-
-#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* number of banks */
-#define CONFIG_SYS_MAX_FLASH_SECT 256 /* max sectors per device */
-
-#undef CONFIG_SYS_FLASH_CHECKSUM
-#define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */
-#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */
-
-#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */
-
-#if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE)
-#define CONFIG_SYS_RAMBOOT
-#else
-#undef CONFIG_SYS_RAMBOOT
-#endif
-
-/*
- * BCSR register on local bus 32KB, 8-bit wide for MDS config reg
- */
-#define CONFIG_SYS_BCSR 0xE2400000
- /* Access window base at BCSR base */
-
-
-#define CONFIG_SYS_INIT_RAM_LOCK 1
-#define CONFIG_SYS_INIT_RAM_ADDR 0xFD000000 /* Initial RAM addr */
-#define CONFIG_SYS_INIT_RAM_SIZE 0x1000 /* Size of used area in RAM*/
-
-#define CONFIG_SYS_GBL_DATA_OFFSET \
- (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
-#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
-
-#define CONFIG_SYS_MONITOR_LEN (512 * 1024) /* Reserve 512 kB for Mon */
-#define CONFIG_SYS_MALLOC_LEN (256 * 1024) /* Reserved for malloc */
-
-/*
- * Serial Port
- */
-#define CONFIG_SYS_NS16550_SERIAL
-#define CONFIG_SYS_NS16550_REG_SIZE 1
-#define CONFIG_SYS_NS16550_CLK get_bus_freq(0)
-
-#define CONFIG_SYS_BAUDRATE_TABLE \
- {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 115200}
-
-#define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_IMMR+0x4500)
-#define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_IMMR+0x4600)
-
-/* I2C */
-#define CONFIG_SYS_I2C_LEGACY
-#define CONFIG_SYS_I2C_FSL
-#define CONFIG_SYS_FSL_I2C_SPEED 400000
-#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F
-#define CONFIG_SYS_FSL_I2C_OFFSET 0x3000
-#define CONFIG_SYS_FSL_I2C2_SPEED 400000
-#define CONFIG_SYS_FSL_I2C2_SLAVE 0x7F
-#define CONFIG_SYS_FSL_I2C2_OFFSET 0x3100
-#define CONFIG_SYS_I2C_NOPROBES { {0, 0x69} }
-
-/* SPI */
-#undef CONFIG_SOFT_SPI /* SPI bit-banged */
-
-/* GPIOs. Used as SPI chip selects */
-#define CONFIG_SYS_GPIO1_PRELIM
-#define CONFIG_SYS_GPIO1_DIR 0xC0000000 /* SPI CS on 0, LED on 1 */
-#define CONFIG_SYS_GPIO1_DAT 0xC0000000 /* Both are active LOW */
-
-/* TSEC */
-#define CONFIG_SYS_TSEC1_OFFSET 0x24000
-#define CONFIG_SYS_TSEC1 (CONFIG_SYS_IMMR+CONFIG_SYS_TSEC1_OFFSET)
-#define CONFIG_SYS_TSEC2_OFFSET 0x25000
-#define CONFIG_SYS_TSEC2 (CONFIG_SYS_IMMR+CONFIG_SYS_TSEC2_OFFSET)
-
-/* USB */
-#define CONFIG_SYS_USE_MPC834XSYS_USB_PHY 1 /* Use SYS board PHY */
-
-/*
- * General PCI
- * Addresses are mapped 1-1.
- */
-#define CONFIG_SYS_PCI1_MEM_BASE 0x80000000
-#define CONFIG_SYS_PCI1_MEM_PHYS CONFIG_SYS_PCI1_MEM_BASE
-#define CONFIG_SYS_PCI1_MEM_SIZE 0x10000000 /* 256M */
-#define CONFIG_SYS_PCI1_MMIO_BASE 0x90000000
-#define CONFIG_SYS_PCI1_MMIO_PHYS CONFIG_SYS_PCI1_MMIO_BASE
-#define CONFIG_SYS_PCI1_MMIO_SIZE 0x10000000 /* 256M */
-#define CONFIG_SYS_PCI1_IO_BASE 0x00000000
-#define CONFIG_SYS_PCI1_IO_PHYS 0xE2000000
-#define CONFIG_SYS_PCI1_IO_SIZE 0x00100000 /* 1M */
-
-#define CONFIG_SYS_PCI2_MEM_BASE 0xA0000000
-#define CONFIG_SYS_PCI2_MEM_PHYS CONFIG_SYS_PCI2_MEM_BASE
-#define CONFIG_SYS_PCI2_MEM_SIZE 0x10000000 /* 256M */
-#define CONFIG_SYS_PCI2_MMIO_BASE 0xB0000000
-#define CONFIG_SYS_PCI2_MMIO_PHYS CONFIG_SYS_PCI2_MMIO_BASE
-#define CONFIG_SYS_PCI2_MMIO_SIZE 0x10000000 /* 256M */
-#define CONFIG_SYS_PCI2_IO_BASE 0x00000000
-#define CONFIG_SYS_PCI2_IO_PHYS 0xE2100000
-#define CONFIG_SYS_PCI2_IO_SIZE 0x00100000 /* 1M */
-
-#if defined(CONFIG_PCI)
-
-#define CONFIG_83XX_PCI_STREAMING
-
-
-#if !defined(CONFIG_PCI_PNP)
- #define PCI_ENET0_IOADDR 0xFIXME
- #define PCI_ENET0_MEMADDR 0xFIXME
- #define PCI_IDSEL_NUMBER 0x0c /* slot0->3(IDSEL)=12->15 */
-#endif
-
-#undef CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */
-#define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x1957 /* Freescale */
-
-#endif /* CONFIG_PCI */
-
-/*
- * TSEC configuration
- */
-
-#if defined(CONFIG_TSEC_ENET)
-
-#define CONFIG_GMII 1 /* MII PHY management */
-#define CONFIG_TSEC1 1
-#define CONFIG_TSEC1_NAME "TSEC0"
-#define CONFIG_TSEC2 1
-#define CONFIG_TSEC2_NAME "TSEC1"
-#define TSEC1_PHY_ADDR 0
-#define TSEC2_PHY_ADDR 1
-#define TSEC1_PHYIDX 0
-#define TSEC2_PHYIDX 0
-#define TSEC1_FLAGS TSEC_GIGABIT
-#define TSEC2_FLAGS TSEC_GIGABIT
-
-/* Options are: TSEC[0-1] */
-#define CONFIG_ETHPRIME "TSEC0"
-
-#endif /* CONFIG_TSEC_ENET */
-
-/*
- * Configure on-board RTC
- */
-#define CONFIG_RTC_DS1374 /* use ds1374 rtc via i2c */
-#define CONFIG_SYS_I2C_RTC_ADDR 0x68 /* at address 0x68 */
-
-/*
- * Environment
- */
-#ifndef CONFIG_SYS_RAMBOOT
-/* Address and size of Redundant Environment Sector */
-#endif
-
-#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
-#define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
-
-/*
- * BOOTP options
- */
-#define CONFIG_BOOTP_BOOTFILESIZE
-
-#undef CONFIG_WATCHDOG /* watchdog disabled */
-
-/*
- * Miscellaneous configurable options
- */
-#define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */
-
-/*
- * For booting Linux, the board info and command line data
- * have to be in the first 256 MB of memory, since this is
- * the maximum mapped by the Linux kernel during initialization.
- */
- /* Initial Memory map for Linux*/
-#define CONFIG_SYS_BOOTMAPSZ (256 << 20)
-#define CONFIG_SYS_BOOTM_LEN (64 << 20) /* Increase max gunzip size */
-
-#define CONFIG_SYS_RCWH_PCIHOST 0x80000000 /* PCIHOST */
-
-/*
- * System performance
- */
-#define CONFIG_SYS_SCCR_TSEC1CM 1 /* TSEC1 clock mode (0-3) */
-#define CONFIG_SYS_SCCR_TSEC2CM 1 /* TSEC2 & I2C0 clock mode (0-3) */
-
-/* System IO Config */
-#define CONFIG_SYS_SICRH 0
-#define CONFIG_SYS_SICRL SICRL_LDP_A
-
-#ifdef CONFIG_PCI
-#define CONFIG_PCI_INDIRECT_BRIDGE
-#endif
-
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_KGDB_BAUDRATE 230400 /* speed of kgdb serial port */
-#endif
-
-/*
- * Environment Configuration
- */
-
-#if defined(CONFIG_TSEC_ENET)
-#define CONFIG_HAS_ETH1
-#define CONFIG_HAS_ETH0
-#endif
-
-#define CONFIG_HOSTNAME "mpc8349emds"
-#define CONFIG_ROOTPATH "/nfsroot/rootfs"
-#define CONFIG_BOOTFILE "uImage"
-
-#define CONFIG_LOADADDR 800000 /* default location for tftp and bootm */
-
-#define CONFIG_EXTRA_ENV_SETTINGS \
- "netdev=eth0\0" \
- "hostname=mpc8349emds\0" \
- "nfsargs=setenv bootargs root=/dev/nfs rw " \
- "nfsroot=${serverip}:${rootpath}\0" \
- "ramargs=setenv bootargs root=/dev/ram rw\0" \
- "addip=setenv bootargs ${bootargs} " \
- "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \
- ":${hostname}:${netdev}:off panic=1\0" \
- "addtty=setenv bootargs ${bootargs} console=ttyS0,${baudrate}\0"\
- "flash_nfs=run nfsargs addip addtty;" \
- "bootm ${kernel_addr}\0" \
- "flash_self=run ramargs addip addtty;" \
- "bootm ${kernel_addr} ${ramdisk_addr}\0" \
- "net_nfs=tftp 200000 ${bootfile};run nfsargs addip addtty;" \
- "bootm\0" \
- "load=tftp 100000 /tftpboot/mpc8349emds/u-boot.bin\0" \
- "update=protect off fe000000 fe03ffff; " \
- "era fe000000 fe03ffff; cp.b 100000 fe000000 ${filesize}\0"\
- "upd=run load update\0" \
- "fdtaddr=780000\0" \
- "fdtfile=mpc834x_mds.dtb\0" \
- ""
-
-#define CONFIG_NFSBOOTCOMMAND \
- "setenv bootargs root=/dev/nfs rw " \
- "nfsroot=$serverip:$rootpath " \
- "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:" \
- "$netdev:off " \
- "console=$consoledev,$baudrate $othbootargs;" \
- "tftp $loadaddr $bootfile;" \
- "tftp $fdtaddr $fdtfile;" \
- "bootm $loadaddr - $fdtaddr"
-
-#define CONFIG_RAMBOOTCOMMAND \
- "setenv bootargs root=/dev/ram rw " \
- "console=$consoledev,$baudrate $othbootargs;" \
- "tftp $ramdiskaddr $ramdiskfile;" \
- "tftp $loadaddr $bootfile;" \
- "tftp $fdtaddr $fdtfile;" \
- "bootm $loadaddr $ramdiskaddr $fdtaddr"
-
-#define CONFIG_BOOTCOMMAND "run flash_self"
-
-#endif /* __CONFIG_H */
projects / platform / kernel / u-boot.git / blobdiff