+++ /dev/null
-/* SPDX-License-Identifier: GPL-2.0+ */
-/*
- * Copyright (C) 2007-2010 Freescale Semiconductor, Inc.
- *
- * Dave Liu <daveliu@freescale.com>
- */
-
-#ifndef __CONFIG_H
-#define __CONFIG_H
-
-#define CONFIG_SYS_NAND_U_BOOT_SIZE (512 << 10)
-#define CONFIG_SYS_NAND_U_BOOT_DST 0x00100000
-#define CONFIG_SYS_NAND_U_BOOT_START 0x00100100
-#define CONFIG_SYS_NAND_U_BOOT_OFFS 16384
-#define CONFIG_SYS_NAND_U_BOOT_RELOC 0x00010000
-
-#ifndef CONFIG_SYS_MONITOR_BASE
-#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */
-#endif
-
-/*
- * High Level Configuration Options
- */
-#define CONFIG_E300 1 /* E300 family */
-
-/*
- * System IO Config
- */
-#define CONFIG_SYS_SICRH 0x00000000
-#define CONFIG_SYS_SICRL 0x00000000 /* 3.3V, no delay */
-
-#define CONFIG_HWCONFIG
-
-/*
- * DDR Setup
- */
-#define CONFIG_SYS_SDRAM_BASE 0x00000000 /* DDR is system memory */
-#define CONFIG_SYS_DDR_SDRAM_BASE CONFIG_SYS_SDRAM_BASE
-#define CONFIG_SYS_DDR_SDRAM_CLK_CNTL DDR_SDRAM_CLK_CNTL_CLK_ADJUST_05
-#define CONFIG_SYS_DDRCDR_VALUE (DDRCDR_EN \
- | DDRCDR_PZ_LOZ \
- | DDRCDR_NZ_LOZ \
- | DDRCDR_ODT \
- | DDRCDR_Q_DRN)
- /* 0x7b880001 */
-/*
- * Manually set up DDR parameters
- * consist of two chips HY5PS12621BFP-C4 from HYNIX
- */
-#define CONFIG_SYS_DDR_SIZE 128 /* MB */
-#define CONFIG_SYS_DDR_CS0_BNDS 0x00000007
-#define CONFIG_SYS_DDR_CS0_CONFIG (CSCONFIG_EN \
- | CSCONFIG_ODT_RD_NEVER \
- | CSCONFIG_ODT_WR_ONLY_CURRENT \
- | CSCONFIG_ROW_BIT_13 \
- | CSCONFIG_COL_BIT_10)
- /* 0x80010102 */
-#define CONFIG_SYS_DDR_TIMING_3 0x00000000
-#define CONFIG_SYS_DDR_TIMING_0 ((0 << TIMING_CFG0_RWT_SHIFT) \
- | (0 << TIMING_CFG0_WRT_SHIFT) \
- | (0 << TIMING_CFG0_RRT_SHIFT) \
- | (0 << TIMING_CFG0_WWT_SHIFT) \
- | (2 << TIMING_CFG0_ACT_PD_EXIT_SHIFT) \
- | (2 << TIMING_CFG0_PRE_PD_EXIT_SHIFT) \
- | (8 << TIMING_CFG0_ODT_PD_EXIT_SHIFT) \
- | (2 << TIMING_CFG0_MRS_CYC_SHIFT))
- /* 0x00220802 */
-#define CONFIG_SYS_DDR_TIMING_1 ((2 << TIMING_CFG1_PRETOACT_SHIFT) \
- | (7 << TIMING_CFG1_ACTTOPRE_SHIFT) \
- | (2 << TIMING_CFG1_ACTTORW_SHIFT) \
- | (5 << TIMING_CFG1_CASLAT_SHIFT) \
- | (6 << TIMING_CFG1_REFREC_SHIFT) \
- | (2 << TIMING_CFG1_WRREC_SHIFT) \
- | (2 << TIMING_CFG1_ACTTOACT_SHIFT) \
- | (2 << TIMING_CFG1_WRTORD_SHIFT))
- /* 0x27256222 */
-#define CONFIG_SYS_DDR_TIMING_2 ((1 << TIMING_CFG2_ADD_LAT_SHIFT) \
- | (4 << TIMING_CFG2_CPO_SHIFT) \
- | (2 << TIMING_CFG2_WR_LAT_DELAY_SHIFT) \
- | (2 << TIMING_CFG2_RD_TO_PRE_SHIFT) \
- | (2 << TIMING_CFG2_WR_DATA_DELAY_SHIFT) \
- | (3 << TIMING_CFG2_CKE_PLS_SHIFT) \
- | (5 << TIMING_CFG2_FOUR_ACT_SHIFT))
- /* 0x121048c5 */
-#define CONFIG_SYS_DDR_INTERVAL ((0x0360 << SDRAM_INTERVAL_REFINT_SHIFT) \
- | (0x0100 << SDRAM_INTERVAL_BSTOPRE_SHIFT))
- /* 0x03600100 */
-#define CONFIG_SYS_DDR_SDRAM_CFG (SDRAM_CFG_SREN \
- | SDRAM_CFG_SDRAM_TYPE_DDR2 \
- | SDRAM_CFG_DBW_32)
- /* 0x43080000 */
-#define CONFIG_SYS_DDR_SDRAM_CFG2 0x00401000 /* 1 posted refresh */
-#define CONFIG_SYS_DDR_MODE ((0x0448 << SDRAM_MODE_ESD_SHIFT) \
- | (0x0232 << SDRAM_MODE_SD_SHIFT))
- /* ODT 150ohm CL=3, AL=1 on SDRAM */
-#define CONFIG_SYS_DDR_MODE2 0x00000000
-
-/*
- * Memory test
- */
-#undef CONFIG_SYS_DRAM_TEST /* memory test, takes time */
-#define CONFIG_SYS_MEMTEST_START 0x00040000 /* memtest region */
-#define CONFIG_SYS_MEMTEST_END 0x00140000
-
-/*
- * The reserved memory
- */
-#define CONFIG_SYS_MONITOR_LEN (512 * 1024) /* Reserve 512 kB for Mon */
-#define CONFIG_SYS_MALLOC_LEN (512 * 1024) /* Reserved for malloc */
-
-/*
- * Initial RAM Base Address Setup
- */
-#define CONFIG_SYS_INIT_RAM_LOCK 1
-#define CONFIG_SYS_INIT_RAM_ADDR 0xE6000000 /* Initial RAM address */
-#define CONFIG_SYS_INIT_RAM_SIZE 0x1000 /* Size of used area in RAM */
-#define CONFIG_SYS_GBL_DATA_OFFSET \
- (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
-
-/*
- * Local Bus Configuration & Clock Setup
- */
-#define CONFIG_SYS_LBC_LBCR 0x00040000
-#define CONFIG_FSL_ELBC 1
-
-/*
- * FLASH on the Local Bus
- */
-#define CONFIG_SYS_FLASH_CFI_WIDTH FLASH_CFI_16BIT
-
-#define CONFIG_SYS_FLASH_BASE 0xFE000000 /* FLASH base address */
-#define CONFIG_SYS_FLASH_SIZE 8 /* FLASH size is 8M */
-
-#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* number of banks */
-/* 127 64KB sectors and 8 8KB top sectors per device */
-#define CONFIG_SYS_MAX_FLASH_SECT 135
-
-#undef CONFIG_SYS_FLASH_CHECKSUM
-#define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */
-#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */
-
-/*
- * NAND Flash on the Local Bus
- */
-
-#ifdef CONFIG_NAND_SPL
-#define CONFIG_SYS_NAND_BASE 0xFFF00000
-#else
-#define CONFIG_SYS_NAND_BASE 0xE0600000
-#endif
-
-#define CONFIG_MTD_PARTITION
-
-#define CONFIG_SYS_MAX_NAND_DEVICE 1
-#define CONFIG_NAND_FSL_ELBC 1
-#define CONFIG_SYS_NAND_BLOCK_SIZE 16384
-#define CONFIG_SYS_NAND_WINDOW_SIZE (32 * 1024) /* 0x00008000 */
-
-#define CONFIG_SYS_NAND_U_BOOT_SIZE (512 << 10)
-#define CONFIG_SYS_NAND_U_BOOT_DST 0x00100000
-#define CONFIG_SYS_NAND_U_BOOT_START 0x00100100
-#define CONFIG_SYS_NAND_U_BOOT_OFFS 16384
-#define CONFIG_SYS_NAND_U_BOOT_RELOC 0x00010000
-
-
-
-/* Still needed for spl_minimal.c */
-#define CONFIG_SYS_NAND_BR_PRELIM CONFIG_SYS_BR1_PRELIM
-#define CONFIG_SYS_NAND_OR_PRELIM CONFIG_SYS_OR1_PRELIM
-
-#if CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE && \
- !defined(CONFIG_NAND_SPL)
-#define CONFIG_SYS_RAMBOOT
-#else
-#undef CONFIG_SYS_RAMBOOT
-#endif
-
-/*
- * Serial Port
- */
-#define CONFIG_SYS_NS16550_SERIAL
-#define CONFIG_SYS_NS16550_REG_SIZE 1
-#define CONFIG_SYS_NS16550_CLK (get_bus_freq(0))
-
-#define CONFIG_SYS_BAUDRATE_TABLE \
- {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200}
-
-#define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_IMMR+0x4500)
-#define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_IMMR+0x4600)
-
-/* I2C */
-#define CONFIG_SYS_I2C
-#define CONFIG_SYS_I2C_FSL
-#define CONFIG_SYS_FSL_I2C_SPEED 400000
-#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F
-#define CONFIG_SYS_FSL_I2C_OFFSET 0x3000
-#define CONFIG_SYS_I2C_NOPROBES { {0, 0x51} }
-
-/*
- * Board info - revision and where boot from
- */
-#define CONFIG_SYS_I2C_PCF8574A_ADDR 0x39
-
-/*
- * Config on-board RTC
- */
-#define CONFIG_RTC_DS1337 /* ds1339 on board, use ds1337 rtc via i2c */
-#define CONFIG_SYS_I2C_RTC_ADDR 0x68 /* at address 0x68 */
-
-/*
- * General PCI
- * Addresses are mapped 1-1.
- */
-#define CONFIG_SYS_PCI_MEM_BASE 0x80000000
-#define CONFIG_SYS_PCI_MEM_PHYS CONFIG_SYS_PCI_MEM_BASE
-#define CONFIG_SYS_PCI_MEM_SIZE 0x10000000 /* 256M */
-#define CONFIG_SYS_PCI_MMIO_BASE 0x90000000
-#define CONFIG_SYS_PCI_MMIO_PHYS CONFIG_SYS_PCI_MMIO_BASE
-#define CONFIG_SYS_PCI_MMIO_SIZE 0x10000000 /* 256M */
-#define CONFIG_SYS_PCI_IO_BASE 0x00000000
-#define CONFIG_SYS_PCI_IO_PHYS 0xE0300000
-#define CONFIG_SYS_PCI_IO_SIZE 0x100000 /* 1M */
-
-#define CONFIG_SYS_PCI_SLV_MEM_LOCAL CONFIG_SYS_SDRAM_BASE
-#define CONFIG_SYS_PCI_SLV_MEM_BUS 0x00000000
-#define CONFIG_SYS_PCI_SLV_MEM_SIZE 0x80000000
-
-#define CONFIG_SYS_PCIE1_BASE 0xA0000000
-#define CONFIG_SYS_PCIE1_MEM_BASE 0xA0000000
-#define CONFIG_SYS_PCIE1_MEM_PHYS 0xA0000000
-#define CONFIG_SYS_PCIE1_MEM_SIZE 0x10000000
-#define CONFIG_SYS_PCIE1_CFG_BASE 0xB0000000
-#define CONFIG_SYS_PCIE1_CFG_SIZE 0x01000000
-#define CONFIG_SYS_PCIE1_IO_BASE 0x00000000
-#define CONFIG_SYS_PCIE1_IO_PHYS 0xB1000000
-#define CONFIG_SYS_PCIE1_IO_SIZE 0x00800000
-
-#define CONFIG_SYS_PCIE2_BASE 0xC0000000
-#define CONFIG_SYS_PCIE2_MEM_BASE 0xC0000000
-#define CONFIG_SYS_PCIE2_MEM_PHYS 0xC0000000
-#define CONFIG_SYS_PCIE2_MEM_SIZE 0x10000000
-#define CONFIG_SYS_PCIE2_CFG_BASE 0xD0000000
-#define CONFIG_SYS_PCIE2_CFG_SIZE 0x01000000
-#define CONFIG_SYS_PCIE2_IO_BASE 0x00000000
-#define CONFIG_SYS_PCIE2_IO_PHYS 0xD1000000
-#define CONFIG_SYS_PCIE2_IO_SIZE 0x00800000
-
-#define CONFIG_PCI_INDIRECT_BRIDGE
-#define CONFIG_PCIE
-
-#define CONFIG_EEPRO100
-#undef CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */
-#define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x1957 /* Freescale */
-
-#define CONFIG_HAS_FSL_DR_USB
-#define CONFIG_SYS_SCCR_USBDRCM 3
-
-#define CONFIG_USB_EHCI_FSL
-#define CONFIG_USB_PHY_TYPE "utmi"
-#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
-
-/*
- * TSEC
- */
-#define CONFIG_SYS_TSEC1_OFFSET 0x24000
-#define CONFIG_SYS_TSEC1 (CONFIG_SYS_IMMR+CONFIG_SYS_TSEC1_OFFSET)
-#define CONFIG_SYS_TSEC2_OFFSET 0x25000
-#define CONFIG_SYS_TSEC2 (CONFIG_SYS_IMMR+CONFIG_SYS_TSEC2_OFFSET)
-
-/*
- * TSEC ethernet configuration
- */
-#define CONFIG_TSEC1 1
-#define CONFIG_TSEC1_NAME "eTSEC0"
-#define CONFIG_TSEC2 1
-#define CONFIG_TSEC2_NAME "eTSEC1"
-#define TSEC1_PHY_ADDR 0
-#define TSEC2_PHY_ADDR 1
-#define TSEC1_PHYIDX 0
-#define TSEC2_PHYIDX 0
-#define TSEC1_FLAGS TSEC_GIGABIT
-#define TSEC2_FLAGS TSEC_GIGABIT
-
-/* Options are: eTSEC[0-1] */
-#define CONFIG_ETHPRIME "eTSEC1"
-
-/*
- * SATA
- */
-#define CONFIG_SYS_SATA_MAX_DEVICE 2
-#define CONFIG_SATA1
-#define CONFIG_SYS_SATA1_OFFSET 0x18000
-#define CONFIG_SYS_SATA1 (CONFIG_SYS_IMMR + CONFIG_SYS_SATA1_OFFSET)
-#define CONFIG_SYS_SATA1_FLAGS FLAGS_DMA
-#define CONFIG_SATA2
-#define CONFIG_SYS_SATA2_OFFSET 0x19000
-#define CONFIG_SYS_SATA2 (CONFIG_SYS_IMMR + CONFIG_SYS_SATA2_OFFSET)
-#define CONFIG_SYS_SATA2_FLAGS FLAGS_DMA
-
-#ifdef CONFIG_FSL_SATA
-#define CONFIG_LBA48
-#endif
-
-/*
- * Environment
- */
-#if !defined(CONFIG_SYS_RAMBOOT)
- #define CONFIG_ENV_ADDR \
- (CONFIG_SYS_MONITOR_BASE + CONFIG_SYS_MONITOR_LEN)
- #define CONFIG_ENV_SECT_SIZE 0x10000 /* 64K(one sector) for env */
- #define CONFIG_ENV_SIZE 0x2000
-#else
- #define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - 0x1000)
- #define CONFIG_ENV_SIZE 0x2000
-#endif
-
-#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
-#define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
-
-/*
- * BOOTP options
- */
-#define CONFIG_BOOTP_BOOTFILESIZE
-
-/*
- * Command line configuration.
- */
-
-#undef CONFIG_WATCHDOG /* watchdog disabled */
-
-/*
- * Miscellaneous configurable options
- */
-#define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */
-
-/*
- * For booting Linux, the board info and command line data
- * have to be in the first 256 MB of memory, since this is
- * the maximum mapped by the Linux kernel during initialization.
- */
-#define CONFIG_SYS_BOOTMAPSZ (256 << 20) /* Initial Memory map for Linux */
-#define CONFIG_SYS_BOOTM_LEN (64 << 20) /* Increase max gunzip size */
-
-/*
- * MMU Setup
- */
-
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_KGDB_BAUDRATE 230400 /* speed of kgdb serial port */
-#endif
-
-/*
- * Environment Configuration
- */
-
-#define CONFIG_ENV_OVERWRITE
-
-#if defined(CONFIG_TSEC_ENET)
-#define CONFIG_HAS_ETH0
-#define CONFIG_HAS_ETH1
-#endif
-
-#define CONFIG_LOADADDR 800000 /* default location for tftp and bootm */
-
-#define CONFIG_EXTRA_ENV_SETTINGS \
- "netdev=eth0\0" \
- "consoledev=ttyS0\0" \
- "ramdiskaddr=1000000\0" \
- "ramdiskfile=ramfs.83xx\0" \
- "fdtaddr=780000\0" \
- "fdtfile=mpc8315erdb.dtb\0" \
- "usb_phy_type=utmi\0" \
- ""
-
-#define CONFIG_NFSBOOTCOMMAND \
- "setenv bootargs root=/dev/nfs rw " \
- "nfsroot=$serverip:$rootpath " \
- "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:" \
- "$netdev:off " \
- "console=$consoledev,$baudrate $othbootargs;" \
- "tftp $loadaddr $bootfile;" \
- "tftp $fdtaddr $fdtfile;" \
- "bootm $loadaddr - $fdtaddr"
-
-#define CONFIG_RAMBOOTCOMMAND \
- "setenv bootargs root=/dev/ram rw " \
- "console=$consoledev,$baudrate $othbootargs;" \
- "tftp $ramdiskaddr $ramdiskfile;" \
- "tftp $loadaddr $bootfile;" \
- "tftp $fdtaddr $fdtfile;" \
- "bootm $loadaddr $ramdiskaddr $fdtaddr"
-
-#define CONFIG_BOOTCOMMAND CONFIG_NFSBOOTCOMMAND
-
-#endif /* __CONFIG_H */
projects / platform / kernel / u-boot.git / blobdiff