+++ /dev/null
-/*
- * (C) Copyright 2001
- * Stuart Hughes <stuarth@lineo.com>
- * This file is based on similar values for other boards found in other
- * U-Boot config files, and some that I found in the mpc8260ads manual.
- *
- * Note: my board is a PILOT rev.
- * Note: the mpc8260ads doesn't come with a proper Ethernet MAC address.
- *
- * See file CREDITS for list of people who contributed to this
- * project.
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation; either version 2 of
- * the License, or (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
- */
-
-/*
- * Config header file for a MPC8266ADS Pilot 16M Ram Simm, 8Mbytes Flash Simm
- */
-
-/* !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
- !! !!
- !! This configuration requires JP3 to be in position 1-2 to work !!
- !! To make it work for the default, the TEXT_BASE define in !!
- !! board/mpc8266ads/config.mk must be changed from 0xfe000000 to !!
- !! 0xfff00000 !!
- !! The CONFIG_SYS_HRCW_MASTER define below must also be changed to match !!
- !! !!
- !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
- */
-
-#ifndef __CONFIG_H
-#define __CONFIG_H
-
-/*
- * High Level Configuration Options
- * (easy to change)
- */
-
-#define CONFIG_MPC8260 1 /* This is an MPC8260 CPU */
-#define CONFIG_MPC8266ADS 1 /* ...on motorola ADS board */
-#define CONFIG_CPM2 1 /* Has a CPM2 */
-
-#define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_early_init_f */
-
-/* allow serial and ethaddr to be overwritten */
-#define CONFIG_ENV_OVERWRITE
-
-/*
- * select serial console configuration
- *
- * if either CONFIG_CONS_ON_SMC or CONFIG_CONS_ON_SCC is selected, then
- * CONFIG_CONS_INDEX must be set to the channel number (1-2 for SMC, 1-4
- * for SCC).
- *
- * if CONFIG_CONS_NONE is defined, then the serial console routines must
- * defined elsewhere (for example, on the cogent platform, there are serial
- * ports on the motherboard which are used for the serial console - see
- * cogent/cma101/serial.[ch]).
- */
-#undef CONFIG_CONS_ON_SMC /* define if console on SMC */
-#define CONFIG_CONS_ON_SCC /* define if console on SCC */
-#undef CONFIG_CONS_NONE /* define if console on something else */
-#define CONFIG_CONS_INDEX 1 /* which serial channel for console */
-
-/*
- * select ethernet configuration
- *
- * if either CONFIG_ETHER_ON_SCC or CONFIG_ETHER_ON_FCC is selected, then
- * CONFIG_ETHER_INDEX must be set to the channel number (1-4 for SCC, 1-3
- * for FCC)
- *
- * if CONFIG_ETHER_NONE is defined, then either the ethernet routines must be
- * defined elsewhere (as for the console), or CONFIG_CMD_NET must be unset.
- */
-#undef CONFIG_ETHER_ON_SCC /* define if ether on SCC */
-#define CONFIG_ETHER_ON_FCC /* define if ether on FCC */
-#undef CONFIG_ETHER_NONE /* define if ether on something else */
-#define CONFIG_ETHER_INDEX 2 /* which channel for ether */
-#define CONFIG_MII /* MII PHY management */
-#define CONFIG_BITBANGMII /* bit-bang MII PHY management */
-/*
- * Port pins used for bit-banged MII communictions (if applicable).
- */
-#define MDIO_PORT 2 /* Port C */
-#define MDIO_ACTIVE (iop->pdir |= 0x00400000)
-#define MDIO_TRISTATE (iop->pdir &= ~0x00400000)
-#define MDIO_READ ((iop->pdat & 0x00400000) != 0)
-
-#define MDIO(bit) if(bit) iop->pdat |= 0x00400000; \
- else iop->pdat &= ~0x00400000
-
-#define MDC(bit) if(bit) iop->pdat |= 0x00200000; \
- else iop->pdat &= ~0x00200000
-
-#define MIIDELAY udelay(1)
-
-#if (CONFIG_ETHER_INDEX == 2)
-
-/*
- * - Rx-CLK is CLK13
- * - Tx-CLK is CLK14
- * - Select bus for bd/buffers (see 28-13)
- * - Half duplex
- */
-# define CONFIG_SYS_CMXFCR_MASK (CMXFCR_FC2 | CMXFCR_RF2CS_MSK | CMXFCR_TF2CS_MSK)
-# define CONFIG_SYS_CMXFCR_VALUE (CMXFCR_RF2CS_CLK13 | CMXFCR_TF2CS_CLK14)
-# define CONFIG_SYS_CPMFCR_RAMTYPE 0
-# define CONFIG_SYS_FCC_PSMR (FCC_PSMR_FDE | FCC_PSMR_LPB)
-
-#endif /* CONFIG_ETHER_INDEX */
-
-/* other options */
-#define CONFIG_HARD_I2C 1 /* To enable I2C support */
-#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */
-#define CONFIG_SYS_I2C_SLAVE 0x7F
-#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1
-
-/* PCI */
-#define CONFIG_PCI
-#define CONFIG_PCI_PNP
-#define CONFIG_PCI_BOOTDELAY 0
-#undef CONFIG_PCI_SCAN_SHOW
-
-/*-----------------------------------------------------------------------
- * Definitions for Serial Presence Detect EEPROM address
- * (to get SDRAM settings)
- */
-#define SPD_EEPROM_ADDRESS 0x50
-
-#define CONFIG_8260_CLKIN 66000000 /* in Hz */
-#define CONFIG_BAUDRATE 115200
-
-/*
- * Command line configuration.
- */
-#include <config_cmd_default.h>
-
-/* Commands we want, that are not part of default set */
-#define CONFIG_CMD_ASKENV /* ask for env variable */
-#define CONFIG_CMD_CACHE /* icache, dcache */
-#define CONFIG_CMD_DHCP /* DHCP Support */
-#define CONFIG_CMD_DIAG /* Diagnostics */
-#define CONFIG_CMD_IMMAP /* IMMR dump support */
-#define CONFIG_CMD_IRQ /* irqinfo */
-#define CONFIG_CMD_MII /* MII support */
-#define CONFIG_CMD_PCI /* pciinfo */
-#define CONFIG_CMD_PING /* ping support */
-#define CONFIG_CMD_PORTIO /* Port I/O */
-#define CONFIG_CMD_REGINFO /* Register dump */
-#define CONFIG_CMD_SAVES /* save S record dump */
-#define CONFIG_CMD_SDRAM /* SDRAM DIMM SPD info printout */
-
-/* Commands from default set we don't need */
-#undef CONFIG_CMD_FPGA /* FPGA configuration Support */
-#undef CONFIG_CMD_SETGETDCR /* DCR support on 4xx */
-
-/* Define a command string that is automatically executed when no character
- * is read on the console interface withing "Boot Delay" after reset.
- */
-#undef CONFIG_BOOT_ROOT_INITRD /* Use ram disk for the root file system */
-#define CONFIG_BOOT_ROOT_NFS /* Use a NFS mounted root file system */
-
-#ifdef CONFIG_BOOT_ROOT_INITRD
-#define CONFIG_BOOTCOMMAND \
- "version;" \
- "echo;" \
- "bootp;" \
- "setenv bootargs root=/dev/ram0 rw " \
- "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}:${hostname}::off;" \
- "bootm"
-#endif /* CONFIG_BOOT_ROOT_INITRD */
-
-#ifdef CONFIG_BOOT_ROOT_NFS
-#define CONFIG_BOOTCOMMAND \
- "version;" \
- "echo;" \
- "bootp;" \
- "setenv bootargs root=/dev/nfs rw nfsroot=${serverip}:${rootpath} " \
- "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}:${hostname}::off;" \
- "bootm"
-#endif /* CONFIG_BOOT_ROOT_NFS */
-
-/*
- * BOOTP options
- */
-#define CONFIG_BOOTP_SUBNETMASK
-#define CONFIG_BOOTP_GATEWAY
-#define CONFIG_BOOTP_HOSTNAME
-#define CONFIG_BOOTP_BOOTPATH
-#define CONFIG_BOOTP_BOOTFILESIZE
-#define CONFIG_BOOTP_DNS
-
-#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */
-
-#if defined(CONFIG_CMD_KGDB)
-#undef CONFIG_KGDB_ON_SMC /* define if kgdb on SMC */
-#define CONFIG_KGDB_ON_SCC /* define if kgdb on SCC */
-#undef CONFIG_KGDB_NONE /* define if kgdb on something else */
-#define CONFIG_KGDB_INDEX 2 /* which serial channel for kgdb */
-#define CONFIG_KGDB_BAUDRATE 115200 /* speed to run kgdb serial port at */
-#endif
-
-#undef CONFIG_WATCHDOG /* disable platform specific watchdog */
-
-/*
- * Miscellaneous configurable options
- */
-#define CONFIG_SYS_LONGHELP /* undef to save memory */
-#define CONFIG_SYS_PROMPT "=> " /* Monitor Command Prompt */
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
-#else
-#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
-#endif
-#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
-#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
-#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
-
-#define CONFIG_SYS_MEMTEST_START 0x00100000 /* memtest works on */
-#define CONFIG_SYS_MEMTEST_END 0x00f00000 /* 1 ... 15 MB in DRAM */
-
-#undef CONFIG_CLOCKS_IN_MHZ /* clocks passsed to Linux in MHz */
- /* for versions < 2.4.5-pre5 */
-
-#define CONFIG_SYS_LOAD_ADDR 0x100000 /* default load address */
-
-#define CONFIG_SYS_HZ 1000 /* decrementer freq: 1 ms ticks */
-
-#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200, 230400 }
-
-#define CONFIG_SYS_FLASH_BASE 0xFE000000
-#define FLASH_BASE 0xFE000000
-#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max num of memory banks */
-#define CONFIG_SYS_MAX_FLASH_SECT 32 /* max num of sects on one chip */
-#define CONFIG_SYS_FLASH_SIZE 8
-#define CONFIG_SYS_FLASH_ERASE_TOUT 8000 /* Timeout for Flash Erase (in ms) */
-#define CONFIG_SYS_FLASH_WRITE_TOUT 5 /* Timeout for Flash Write (in ms) */
-
-#undef CONFIG_SYS_FLASH_CHECKSUM
-
-/* this is stuff came out of the Motorola docs */
-/* Only change this if you also change the Hardware configuration Word */
-#define CONFIG_SYS_DEFAULT_IMMR 0x0F010000
-
-/* Set IMMR to 0xF0000000 or above to boot Linux */
-#define CONFIG_SYS_IMMR 0xF0000000
-#define CONFIG_SYS_BCSR 0xF8000000
-#define CONFIG_SYS_PCI_INT 0xF8200000 /* PCI interrupt controller */
-
-/* Define CONFIG_VERY_BIG_RAM to allow use of SDRAMs larger than 256MBytes
- */
-/*#define CONFIG_VERY_BIG_RAM 1*/
-
-/* What should be the base address of SDRAM DIMM and how big is
- * it (in Mbytes)? This will normally auto-configure via the SPD.
-*/
-#define CONFIG_SYS_SDRAM_BASE 0x00000000
-#define CONFIG_SYS_SDRAM_SIZE 16
-
-#define SDRAM_SPD_ADDR 0x50
-
-/*-----------------------------------------------------------------------
- * BR2,BR3 - Base Register
- * Ref: Section 10.3.1 on page 10-14
- * OR2,OR3 - Option Register
- * Ref: Section 10.3.2 on page 10-16
- *-----------------------------------------------------------------------
- */
-
-/* Bank 2,3 - SDRAM DIMM
- */
-
-/* The BR2 is configured as follows:
- *
- * - Base address of 0x00000000
- * - 64 bit port size (60x bus only)
- * - Data errors checking is disabled
- * - Read and write access
- * - SDRAM 60x bus
- * - Access are handled by the memory controller according to MSEL
- * - Not used for atomic operations
- * - No data pipelining is done
- * - Valid
- */
-#define CONFIG_SYS_BR2_PRELIM ((CONFIG_SYS_SDRAM_BASE & BRx_BA_MSK) |\
- BRx_PS_64 |\
- BRx_MS_SDRAM_P |\
- BRx_V)
-
-#define CONFIG_SYS_BR3_PRELIM ((CONFIG_SYS_SDRAM_BASE & BRx_BA_MSK) |\
- BRx_PS_64 |\
- BRx_MS_SDRAM_P |\
- BRx_V)
-
-/* With a 64 MB DIMM, the OR2 is configured as follows:
- *
- * - 64 MB
- * - 4 internal banks per device
- * - Row start address bit is A8 with PSDMR[PBI] = 0
- * - 12 row address lines
- * - Back-to-back page mode
- * - Internal bank interleaving within save device enabled
- */
-#if (CONFIG_SYS_SDRAM_SIZE == 64)
-#define CONFIG_SYS_OR2_PRELIM (MEG_TO_AM(CONFIG_SYS_SDRAM_SIZE) |\
- ORxS_BPD_4 |\
- ORxS_ROWST_PBI0_A8 |\
- ORxS_NUMR_12)
-#elif (CONFIG_SYS_SDRAM_SIZE == 16)
-#define CONFIG_SYS_OR2_PRELIM (0xFF000C80)
-#else
-#error "INVALID SDRAM CONFIGURATION"
-#endif
-
-/*-----------------------------------------------------------------------
- * PSDMR - 60x Bus SDRAM Mode Register
- * Ref: Section 10.3.3 on page 10-21
- *-----------------------------------------------------------------------
- */
-
-#if (CONFIG_SYS_SDRAM_SIZE == 64)
-/* With a 64 MB DIMM, the PSDMR is configured as follows:
- *
- * - Bank Based Interleaving,
- * - Refresh Enable,
- * - Address Multiplexing where A5 is output on A14 pin
- * (A6 on A15, and so on),
- * - use address pins A14-A16 as bank select,
- * - A9 is output on SDA10 during an ACTIVATE command,
- * - earliest timing for ACTIVATE command after REFRESH command is 7 clocks,
- * - earliest timing for ACTIVATE or REFRESH command after PRECHARGE command
- * is 3 clocks,
- * - earliest timing for READ/WRITE command after ACTIVATE command is
- * 2 clocks,
- * - earliest timing for PRECHARGE after last data was read is 1 clock,
- * - earliest timing for PRECHARGE after last data was written is 1 clock,
- * - CAS Latency is 2.
- */
-#define CONFIG_SYS_PSDMR (PSDMR_RFEN |\
- PSDMR_SDAM_A14_IS_A5 |\
- PSDMR_BSMA_A14_A16 |\
- PSDMR_SDA10_PBI0_A9 |\
- PSDMR_RFRC_7_CLK |\
- PSDMR_PRETOACT_3W |\
- PSDMR_ACTTORW_2W |\
- PSDMR_LDOTOPRE_1C |\
- PSDMR_WRC_1C |\
- PSDMR_CL_2)
-#elif (CONFIG_SYS_SDRAM_SIZE == 16)
-/* With a 16 MB DIMM, the PSDMR is configured as follows:
- *
- * configuration parameters found in Motorola documentation
- */
-#define CONFIG_SYS_PSDMR (0x016EB452)
-#else
-#error "INVALID SDRAM CONFIGURATION"
-#endif
-
-#define RS232EN_1 0x02000002
-#define RS232EN_2 0x01000001
-#define FETHIEN 0x08000008
-#define FETH_RST 0x04000004
-
-#define CONFIG_SYS_INIT_RAM_ADDR CONFIG_SYS_IMMR
-#define CONFIG_SYS_INIT_RAM_END 0x4000 /* End of used area in DPRAM */
-#define CONFIG_SYS_GBL_DATA_SIZE 128 /* size in bytes reserved for initial data */
-#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_END - CONFIG_SYS_GBL_DATA_SIZE)
-#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
-
-/* Use this HRCW for booting from address 0xfe00000 (JP3 in setting 1-2) */
-/* 0x0EB2B645 */
-#define CONFIG_SYS_HRCW_MASTER (( HRCW_BPS11 | HRCW_CIP ) |\
- ( HRCW_L2CPC10 | HRCW_DPPC11 | HRCW_ISB010 ) |\
- ( HRCW_BMS | HRCW_MMR11 | HRCW_LBPC01 | HRCW_APPC10 ) |\
- ( HRCW_CS10PC01 | HRCW_MODCK_H0101 ) \
- )
-
-/* Use this HRCW for booting from address 0xfff0000 (JP3 in setting 2-3) */
-/* #define CONFIG_SYS_HRCW_MASTER 0x0cb23645 */
-
-/* This value should actually be situated in the first 256 bytes of the FLASH
- which on the standard MPC8266ADS board is at address 0xFF800000
- The linker script places it at 0xFFF00000 instead.
-
- It still works, however, as long as the ADS board jumper JP3 is set to
- position 2-3 so the board is using the BCSR as Hardware Configuration Word
-
- If you want to use the one defined here instead, ust copy the first 256 bytes from
- 0xfff00000 to 0xff800000 (for 8MB flash)
-
- - Rune
-
-*/
-
-/* no slaves */
-#define CONFIG_SYS_HRCW_SLAVE1 0
-#define CONFIG_SYS_HRCW_SLAVE2 0
-#define CONFIG_SYS_HRCW_SLAVE3 0
-#define CONFIG_SYS_HRCW_SLAVE4 0
-#define CONFIG_SYS_HRCW_SLAVE5 0
-#define CONFIG_SYS_HRCW_SLAVE6 0
-#define CONFIG_SYS_HRCW_SLAVE7 0
-
-#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */
-#define BOOTFLAG_WARM 0x02 /* Software reboot */
-
-#define CONFIG_SYS_MONITOR_BASE TEXT_BASE
-#if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE)
-# define CONFIG_SYS_RAMBOOT
-#endif
-
-#define CONFIG_SYS_MONITOR_LEN (256 << 10) /* Reserve 256 kB for Monitor */
-#define CONFIG_SYS_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc() */
-#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
-
-#ifndef CONFIG_SYS_RAMBOOT
-# define CONFIG_ENV_IS_IN_FLASH 1
-# define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE + 0x40000)
-# define CONFIG_ENV_SECT_SIZE 0x40000
-#else
-# define CONFIG_ENV_IS_IN_NVRAM 1
-# define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - 0x1000)
-# define CONFIG_ENV_SIZE 0x200
-#endif /* CONFIG_SYS_RAMBOOT */
-
-#define CONFIG_SYS_CACHELINE_SIZE 32 /* For MPC8260 CPU */
-#if defined(CONFIG_CMD_KGDB)
-# define CONFIG_SYS_CACHELINE_SHIFT 5 /* log base 2 of the above value */
-#endif
-
-/*-----------------------------------------------------------------------
- * HIDx - Hardware Implementation-dependent Registers 2-11
- *-----------------------------------------------------------------------
- * HID0 also contains cache control - initially enable both caches and
- * invalidate contents, then the final state leaves only the instruction
- * cache enabled. Note that Power-On and Hard reset invalidate the caches,
- * but Soft reset does not.
- *
- * HID1 has only read-only information - nothing to set.
- */
-/*#define CONFIG_SYS_HID0_INIT 0 */
-#define CONFIG_SYS_HID0_INIT (HID0_ICE |\
- HID0_DCE |\
- HID0_ICFI |\
- HID0_DCI |\
- HID0_IFEM |\
- HID0_ABE)
-
-#define CONFIG_SYS_HID0_FINAL (HID0_ICE | HID0_IFEM | HID0_ABE )
-
-#define CONFIG_SYS_HID2 0
-
-#define CONFIG_SYS_SYPCR 0xFFFFFFC3
-#define CONFIG_SYS_BCR 0x004C0000
-#define CONFIG_SYS_SIUMCR 0x4E64C000
-#define CONFIG_SYS_SCCR 0x00000000
-
-/* local bus memory map
- *
- * 0x00000000-0x03FFFFFF 64MB SDRAM
- * 0x80000000-0x9FFFFFFF 512MB outbound prefetchable PCI memory window
- * 0xA0000000-0xBFFFFFFF 512MB outbound non-prefetchable PCI memory window
- * 0xF0000000-0xF001FFFF 128KB MPC8266 internal memory
- * 0xF4000000-0xF7FFFFFF 64MB outbound PCI I/O window
- * 0xF8000000-0xF8007FFF 32KB BCSR
- * 0xF8100000-0xF8107FFF 32KB ATM UNI
- * 0xF8200000-0xF8207FFF 32KB PCI interrupt controller
- * 0xF8300000-0xF8307FFF 32KB EEPROM
- * 0xFE000000-0xFFFFFFFF 32MB flash
- */
-#define CONFIG_SYS_BR0_PRELIM 0xFE001801 /* flash */
-#define CONFIG_SYS_OR0_PRELIM 0xFE000836
-#define CONFIG_SYS_BR1_PRELIM (CONFIG_SYS_BCSR | 0x1801) /* BCSR */
-#define CONFIG_SYS_OR1_PRELIM 0xFFFF8010
-#define CONFIG_SYS_BR4_PRELIM 0xF8300801 /* EEPROM */
-#define CONFIG_SYS_OR4_PRELIM 0xFFFF8846
-#define CONFIG_SYS_BR5_PRELIM 0xF8100801 /* PM5350 ATM UNI */
-#define CONFIG_SYS_OR5_PRELIM 0xFFFF8E36
-#define CONFIG_SYS_BR8_PRELIM (CONFIG_SYS_PCI_INT | 0x1801) /* PCI interrupt controller */
-#define CONFIG_SYS_OR8_PRELIM 0xFFFF8010
-
-#define CONFIG_SYS_RMR 0x0001
-#define CONFIG_SYS_TMCNTSC (TMCNTSC_SEC|TMCNTSC_ALR|TMCNTSC_TCF|TMCNTSC_TCE)
-#define CONFIG_SYS_PISCR (PISCR_PS|PISCR_PTF|PISCR_PTE)
-#define CONFIG_SYS_RCCR 0
-#define CONFIG_SYS_MPTPR 0x00001900
-#define CONFIG_SYS_PSRT 0x00000021
-
-/* This address must not exist */
-#define CONFIG_SYS_RESET_ADDRESS 0xFCFFFF00
-
-/* PCI Memory map (if different from default map */
-#define CONFIG_SYS_PCI_SLV_MEM_LOCAL CONFIG_SYS_SDRAM_BASE /* Local base */
-#define CONFIG_SYS_PCI_SLV_MEM_BUS 0x00000000 /* PCI base */
-#define CONFIG_SYS_PICMR0_MASK_ATTRIB (PICMR_MASK_512MB | PICMR_ENABLE | \
- PICMR_PREFETCH_EN)
-
-/*
- * These are the windows that allow the CPU to access PCI address space.
- * All three PCI master windows, which allow the CPU to access PCI
- * prefetch, non prefetch, and IO space (see below), must all fit within
- * these windows.
- */
-
-/* PCIBR0 */
-#define CONFIG_SYS_PCI_MSTR0_LOCAL 0x80000000 /* Local base */
-#define CONFIG_SYS_PCIMSK0_MASK PCIMSK_1GB /* Size of window */
-/* PCIBR1 */
-#define CONFIG_SYS_PCI_MSTR1_LOCAL 0xF4000000 /* Local base */
-#define CONFIG_SYS_PCIMSK1_MASK PCIMSK_64MB /* Size of window */
-
-/*
- * Master window that allows the CPU to access PCI Memory (prefetch).
- * This window will be setup with the first set of Outbound ATU registers
- * in the bridge.
- */
-
-#define CONFIG_SYS_PCI_MSTR_MEM_LOCAL 0x80000000 /* Local base */
-#define CONFIG_SYS_PCI_MSTR_MEM_BUS 0x80000000 /* PCI base */
-#define CONFIG_SYS_CPU_PCI_MEM_START PCI_MSTR_MEM_LOCAL
-#define CONFIG_SYS_PCI_MSTR_MEM_SIZE 0x20000000 /* 512MB */
-#define CONFIG_SYS_POCMR0_MASK_ATTRIB (POCMR_MASK_512MB | POCMR_ENABLE | POCMR_PREFETCH_EN)
-
-/*
- * Master window that allows the CPU to access PCI Memory (non-prefetch).
- * This window will be setup with the second set of Outbound ATU registers
- * in the bridge.
- */
-
-#define CONFIG_SYS_PCI_MSTR_MEMIO_LOCAL 0xA0000000 /* Local base */
-#define CONFIG_SYS_PCI_MSTR_MEMIO_BUS 0xA0000000 /* PCI base */
-#define CONFIG_SYS_CPU_PCI_MEMIO_START PCI_MSTR_MEMIO_LOCAL
-#define CONFIG_SYS_PCI_MSTR_MEMIO_SIZE 0x20000000 /* 512MB */
-#define CONFIG_SYS_POCMR1_MASK_ATTRIB (POCMR_MASK_512MB | POCMR_ENABLE)
-
-/*
- * Master window that allows the CPU to access PCI IO space.
- * This window will be setup with the third set of Outbound ATU registers
- * in the bridge.
- */
-
-#define CONFIG_SYS_PCI_MSTR_IO_LOCAL 0xF4000000 /* Local base */
-#define CONFIG_SYS_PCI_MSTR_IO_BUS 0xF4000000 /* PCI base */
-#define CONFIG_SYS_CPU_PCI_IO_START PCI_MSTR_IO_LOCAL
-#define CONFIG_SYS_PCI_MSTR_IO_SIZE 0x04000000 /* 64MB */
-#define CONFIG_SYS_POCMR2_MASK_ATTRIB (POCMR_MASK_64MB | POCMR_ENABLE | POCMR_PCI_IO)
-
-/*
- * JFFS2 partitions
- *
- */
-/* No command line, one static partition, whole device */
-#undef CONFIG_CMD_MTDPARTS
-#define CONFIG_JFFS2_DEV "nor0"
-#define CONFIG_JFFS2_PART_SIZE 0xFFFFFFFF
-#define CONFIG_JFFS2_PART_OFFSET 0x00000000
-
-/* mtdparts command line support */
-/*
-#define CONFIG_CMD_MTDPARTS
-#define MTDIDS_DEFAULT ""
-#define MTDPARTS_DEFAULT ""
-*/
-
-#endif /* __CONFIG_H */
projects / platform / kernel / u-boot.git / blobdiff