+++ /dev/null
-/*
- * Copyright (C) 2007 Freescale Semiconductor, Inc.
- *
- * Copyright (C) 2011 Matrix Vision GmbH
- * Andre Schwarz <andre.schwarz@matrix-vision.de>
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-#ifndef __CONFIG_H
-#define __CONFIG_H
-
-#include <version.h>
-
-/*
- * High Level Configuration Options
- */
-#define CONFIG_E300 1
-#define CONFIG_MPC83xx 1
-#define CONFIG_MPC837x 1
-#define CONFIG_MPC8377 1
-
-#define CONFIG_SYS_TEXT_BASE 0xFC000000
-
-#define CONFIG_PCI 1
-#define CONFIG_PCI_INDIRECT_BRIDGE 1
-
-#define CONFIG_MASK_AER_AO
-#define CONFIG_DISPLAY_AER_FULL
-
-#define CONFIG_MISC_INIT_R
-
-/*
- * On-board devices
- */
-#define CONFIG_TSEC_ENET
-
-/*
- * System Clock Setup
- */
-#define CONFIG_83XX_CLKIN 66666667 /* in Hz */
-#define CONFIG_PCIE
-#define CONFIG_83XX_GENERIC_PCIE_REGISTER_HOSES
-#define CONFIG_SYS_CLK_FREQ CONFIG_83XX_CLKIN
-
-/*
- * Hardware Reset Configuration Word stored in EEPROM.
- */
-#define CONFIG_SYS_HRCW_LOW 0
-#define CONFIG_SYS_HRCW_HIGH 0
-
-/* Arbiter Configuration Register */
-#define CONFIG_SYS_ACR_PIPE_DEP 3
-#define CONFIG_SYS_ACR_RPTCNT 3
-
-/* System Priority Control Regsiter */
-#define CONFIG_SYS_SPCR_TSECEP 3
-
-/* System Clock Configuration Register */
-#define CONFIG_SYS_SCCR_TSEC1CM 3
-#define CONFIG_SYS_SCCR_TSEC2CM 0
-#define CONFIG_SYS_SCCR_SDHCCM 3
-#define CONFIG_SYS_SCCR_ENCCM 3 /* also clock for I2C-1 */
-#define CONFIG_SYS_SCCR_USBDRCM CONFIG_SYS_SCCR_ENCCM /* must match */
-#define CONFIG_SYS_SCCR_PCIEXP1CM 3
-#define CONFIG_SYS_SCCR_PCIEXP2CM 3
-#define CONFIG_SYS_SCCR_PCICM 1
-#define CONFIG_SYS_SCCR_SATACM 0xFF
-
-/*
- * System IO Config
- */
-#define CONFIG_SYS_SICRH 0x087c0000
-#define CONFIG_SYS_SICRL 0x40000000
-
-/*
- * Output Buffer Impedance
- */
-#define CONFIG_SYS_OBIR 0x30000000
-
-/*
- * IMMR new address
- */
-#define CONFIG_SYS_IMMR 0xE0000000
-
-/*
- * DDR Setup
- */
-#define CONFIG_SYS_DDR_BASE 0x00000000
-#define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_BASE
-#define CONFIG_SYS_DDR_SDRAM_BASE CONFIG_SYS_DDR_BASE
-#define CONFIG_SYS_83XX_DDR_USES_CS0
-
-#define CONFIG_SYS_DDRCDR_VALUE (DDRCDR_EN | DDRCDR_PZ_HIZ |\
- DDRCDR_NZ_HIZ | DDRCDR_ODT |\
- DDRCDR_Q_DRN)
-
-#define CONFIG_SYS_DDR_SDRAM_CLK_CNTL DDR_SDRAM_CLK_CNTL_CLK_ADJUST_05
-
-#define CONFIG_SYS_DDR_MODE_WEAK
-#define CONFIG_SYS_DDR_WRITE_DATA_DELAY 2
-#define CONFIG_SYS_DDR_CPO 0x1f
-
-/* SPD table located at offset 0x20 in extended adressing ROM
- * used for HRCW fetch after power-on reset
- */
-#define CONFIG_SPD_EEPROM
-#define SPD_EEPROM_ADDRESS 0x50
-#define SPD_EEPROM_OFFSET 0x20
-#define SPD_EEPROM_ADDR_LEN 2
-
-/*
- * The reserved memory
- */
-#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE
-#define CONFIG_SYS_MONITOR_LEN (512*1024)
-#define CONFIG_SYS_MALLOC_LEN (512*1024)
-
-/*
- * Initial RAM Base Address Setup
- */
-#define CONFIG_SYS_INIT_RAM_LOCK 1
-#define CONFIG_SYS_INIT_RAM_ADDR 0xE6000000 /* Initial RAM address */
-#define CONFIG_SYS_INIT_RAM_SIZE 0x1000 /* End of used area in RAM */
-#define CONFIG_SYS_GBL_DATA_SIZE 0x100 /* num bytes initial data */
-#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE -\
- CONFIG_SYS_GBL_DATA_SIZE)
-
-/*
- * Local Bus Configuration & Clock Setup
- */
-#define CONFIG_SYS_LCRR_DBYP LCRR_DBYP
-#define CONFIG_SYS_LCRR_CLKDIV LCRR_CLKDIV_8
-#define CONFIG_SYS_LBC_LBCR 0x00000000
-#define CONFIG_FSL_ELBC 1
-
-/*
- * FLASH on the Local Bus
- */
-#define CONFIG_SYS_FLASH_CFI
-#define CONFIG_FLASH_CFI_DRIVER
-#define CONFIG_SYS_FLASH_CFI_WIDTH FLASH_CFI_16BIT
-
-#define CONFIG_SYS_FLASH_BASE CONFIG_SYS_TEXT_BASE
-#define CONFIG_SYS_FLASH_SIZE 64
-
-#define CONFIG_SYS_LBLAWBAR0_PRELIM CONFIG_SYS_FLASH_BASE
-#define CONFIG_SYS_LBLAWAR0_PRELIM (LBLAWAR_EN | LBLAWAR_64MB)
-
-#define CONFIG_SYS_BR0_PRELIM (CONFIG_SYS_FLASH_BASE | BR_PS_16 |\
- BR_MS_GPCM | BR_V)
-#define CONFIG_SYS_OR0_PRELIM (CONFIG_SYS_FLASH_BASE | OR_UPM_XAM |\
- OR_GPCM_CSNT | OR_GPCM_ACS_DIV2 |\
- OR_GPCM_XACS | OR_GPCM_SCY_15 |\
- OR_GPCM_TRLX_SET | OR_GPCM_EHTR_SET |\
- OR_GPCM_EAD)
-
-#define CONFIG_SYS_MAX_FLASH_BANKS 1
-#define CONFIG_SYS_MAX_FLASH_SECT 512
-
-#undef CONFIG_SYS_FLASH_CHECKSUM
-#define CONFIG_SYS_FLASH_ERASE_TOUT 120000 /* Flash Erase Timeout (ms) */
-#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */
-
-/*
- * NAND Flash on the Local Bus
- */
-#define CONFIG_MTD_NAND_VERIFY_WRITE 1
-#define CONFIG_SYS_MAX_NAND_DEVICE 1
-#define CONFIG_NAND_FSL_ELBC 1
-
-#define CONFIG_SYS_NAND_BASE 0xE0600000
-#define CONFIG_SYS_BR1_PRELIM (CONFIG_SYS_NAND_BASE | BR_DECC_CHK_GEN |\
- BR_PS_8 | BR_MS_FCM | BR_V)
-#define CONFIG_SYS_OR1_PRELIM (OR_AM_32KB | OR_FCM_BCTLD | OR_FCM_CST |\
- OR_FCM_CHT | OR_FCM_SCY_1 | OR_FCM_RST |\
- OR_FCM_TRLX | OR_FCM_EHTR)
-
-#define CONFIG_SYS_LBLAWBAR1_PRELIM CONFIG_SYS_NAND_BASE
-#define CONFIG_SYS_LBLAWAR1_PRELIM (LBLAWAR_EN | LBLAWAR_32KB)
-
-/*
- * Serial Port
- */
-#define CONFIG_CONS_INDEX 1
-#define CONFIG_SYS_NS16550
-#define CONFIG_SYS_NS16550_SERIAL
-#define CONFIG_SYS_NS16550_REG_SIZE 1
-#define CONFIG_SYS_NS16550_CLK get_bus_freq(0)
-
-#define CONFIG_SYS_BAUDRATE_TABLE \
- {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200}
-
-#define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_IMMR+0x4500)
-#define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_IMMR+0x4600)
-
-#define CONFIG_CONSOLE ttyS0
-#define CONFIG_BAUDRATE 115200
-
-/* SERDES */
-#define CONFIG_FSL_SERDES
-#define CONFIG_FSL_SERDES1 0xe3000
-#define CONFIG_FSL_SERDES2 0xe3100
-
-/* Use the HUSH parser */
-#define CONFIG_SYS_HUSH_PARSER
-
-/* Pass open firmware flat tree */
-#define CONFIG_OF_LIBFDT 1
-#define CONFIG_OF_BOARD_SETUP 1
-#define CONFIG_OF_STDOUT_VIA_ALIAS 1
-
-/* I2C */
-#define CONFIG_SYS_I2C
-#define CONFIG_SYS_I2C_FSL
-#define CONFIG_SYS_FSL_I2C_SPEED 400000
-#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F
-#define CONFIG_SYS_FSL_I2C_OFFSET 0x3000
-#define CONFIG_SYS_FSL_I2C2_SPEED 400000
-#define CONFIG_SYS_FSL_I2C2_SLAVE 0x7F
-#define CONFIG_SYS_FSL_I2C2_OFFSET 0x3100
-
-/*
- * General PCI
- * Addresses are mapped 1-1.
- */
-#define CONFIG_SYS_PCI_MEM_BASE 0x80000000
-#define CONFIG_SYS_PCI_MEM_PHYS CONFIG_SYS_PCI_MEM_BASE
-#define CONFIG_SYS_PCI_MEM_SIZE (256 << 20)
-#define CONFIG_SYS_PCI_MMIO_BASE 0x90000000
-#define CONFIG_SYS_PCI_MMIO_PHYS CONFIG_SYS_PCI_MMIO_BASE
-#define CONFIG_SYS_PCI_MMIO_SIZE (256 << 20)
-#define CONFIG_SYS_PCI_IO_BASE 0x00000000
-#define CONFIG_SYS_PCI_IO_PHYS 0xE0300000
-#define CONFIG_SYS_PCI_IO_SIZE (1 << 20)
-
-#ifdef CONFIG_PCIE
-#define CONFIG_SYS_PCIE1_BASE 0xA0000000
-#define CONFIG_SYS_PCIE1_CFG_BASE 0xA0000000
-#define CONFIG_SYS_PCIE1_CFG_SIZE (128 << 20)
-#define CONFIG_SYS_PCIE1_MEM_BASE 0xA8000000
-#define CONFIG_SYS_PCIE1_MEM_PHYS 0xA8000000
-#define CONFIG_SYS_PCIE1_MEM_SIZE (256 << 20)
-#define CONFIG_SYS_PCIE1_IO_BASE 0x00000000
-#define CONFIG_SYS_PCIE1_IO_PHYS 0xB8000000
-#define CONFIG_SYS_PCIE1_IO_SIZE (8 << 20)
-
-#define CONFIG_SYS_PCIE2_BASE 0xC0000000
-#define CONFIG_SYS_PCIE2_CFG_BASE 0xC0000000
-#define CONFIG_SYS_PCIE2_CFG_SIZE (128 << 20)
-#define CONFIG_SYS_PCIE2_MEM_BASE 0xC8000000
-#define CONFIG_SYS_PCIE2_MEM_PHYS 0xC8000000
-#define CONFIG_SYS_PCIE2_MEM_SIZE (256 << 20)
-#define CONFIG_SYS_PCIE2_IO_BASE 0x00000000
-#define CONFIG_SYS_PCIE2_IO_PHYS 0xD8000000
-#define CONFIG_SYS_PCIE2_IO_SIZE (8 << 20)
-#endif
-
-#define CONFIG_PCI_PNP
-#define CONFIG_PCI_SCAN_SHOW
-#define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x1957 /* Freescale */
-
-/*
- * TSEC
- */
-#define CONFIG_GMII /* MII PHY management */
-#define CONFIG_SYS_VSC8601_SKEWFIX
-#define CONFIG_SYS_VSC8601_SKEW_TX 3
-#define CONFIG_SYS_VSC8601_SKEW_RX 3
-
-#define CONFIG_TSEC1
-#define CONFIG_HAS_ETH0
-#define CONFIG_TSEC1_NAME "TSEC0"
-#define CONFIG_SYS_TSEC1_OFFSET 0x24000
-#define TSEC1_PHY_ADDR 0x10
-#define TSEC1_FLAGS (TSEC_GIGABIT | TSEC_REDUCED)
-#define TSEC1_PHYIDX 0
-
-#define CONFIG_ETHPRIME "TSEC0"
-#define CONFIG_HAS_ETH0
-
-/*
- * SATA
- */
-#define CONFIG_LIBATA
-#define CONFIG_FSL_SATA
-
-#define CONFIG_SYS_SATA_MAX_DEVICE 2
-#define CONFIG_SATA1
-#define CONFIG_SYS_SATA1_OFFSET 0x18000
-#define CONFIG_SYS_SATA1 (CONFIG_SYS_IMMR + CONFIG_SYS_SATA1_OFFSET)
-#define CONFIG_SYS_SATA1_FLAGS FLAGS_DMA
-#define CONFIG_SATA2
-#define CONFIG_SYS_SATA2_OFFSET 0x19000
-#define CONFIG_SYS_SATA2 (CONFIG_SYS_IMMR + CONFIG_SYS_SATA2_OFFSET)
-#define CONFIG_SYS_SATA2_FLAGS FLAGS_DMA
-
-#define CONFIG_LBA48
-#define CONFIG_CMD_SATA
-#define CONFIG_DOS_PARTITION
-#define CONFIG_CMD_EXT2
-
-/*
- * BOOTP options
- */
-#define CONFIG_BOOTP_BOOTFILESIZE
-#define CONFIG_BOOTP_BOOTPATH
-#define CONFIG_BOOTP_GATEWAY
-#define CONFIG_BOOTP_HOSTNAME
-#define CONFIG_BOOTP_VENDOREX
-#define CONFIG_BOOTP_SUBNETMASK
-#define CONFIG_BOOTP_DNS
-#define CONFIG_BOOTP_DNS2
-#define CONFIG_BOOTP_NTPSERVER
-#define CONFIG_BOOTP_RANDOM_DELAY
-#define CONFIG_BOOTP_SEND_HOSTNAME
-
-/*
- * Command line configuration.
- */
-#include <config_cmd_default.h>
-
-#define CONFIG_CMD_ASKENV
-#define CONFIG_CMD_NAND
-#define CONFIG_CMD_PING
-#define CONFIG_CMD_EEPROM
-#define CONFIG_CMD_I2C
-#define CONFIG_CMD_MII
-#define CONFIG_CMD_PCI
-#define CONFIG_CMD_USB
-#define CONFIG_CMD_SPI
-#define CONFIG_CMD_DHCP
-#define CONFIG_CMD_UBI
-#define CONFIG_CMD_UBIFS
-#define CONFIG_CMD_MTDPARTS
-#define CONFIG_CMD_SATA
-
-#define CONFIG_CMD_EXT2
-#define CONFIG_CMD_FAT
-#define CONFIG_CMD_JFFS2
-
-#define CONFIG_RBTREE
-#define CONFIG_LZO
-
-#define CONFIG_MTD_DEVICE
-#define CONFIG_MTD_PARTITIONS
-
-#define CONFIG_FLASH_CFI_MTD
-#define MTDIDS_DEFAULT "nor0=NOR,nand0=NAND"
-#define MTDPARTS_DEFAULT "mtdparts=NOR:1M(u-boot),2M(FPGA);NAND:-(root)"
-
-#define CONFIG_FIT
-#define CONFIG_FIT_VERBOSE 1
-
-#define CONFIG_CMDLINE_EDITING 1
-#define CONFIG_AUTO_COMPLETE
-
-/*
- * Miscellaneous configurable options
- */
-#define CONFIG_SYS_LONGHELP
-#define CONFIG_SYS_LOAD_ADDR 0x2000000
-#define CONFIG_LOADADDR 0x4000000
-#define CONFIG_SYS_CBSIZE 256
-
-#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16)
-#define CONFIG_SYS_MAXARGS 16
-#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE
-
-#define CONFIG_LOADS_ECHO 1
-#define CONFIG_SYS_LOADS_BAUD_CHANGE 1
-
-#define CONFIG_SYS_MEMTEST_START (60<<20)
-#define CONFIG_SYS_MEMTEST_END (70<<20)
-
-/*
- * For booting Linux, the board info and command line data
- * have to be in the first 256 MB of memory, since this is
- * the maximum mapped by the Linux kernel during initialization.
- */
-#define CONFIG_SYS_BOOTMAPSZ (256 << 20) /* Initial Memory map for Linux */
-
-/*
- * Core HID Setup
- */
-#define CONFIG_SYS_HID0_INIT 0x000000000
-#define CONFIG_SYS_HID0_FINAL (HID0_ENABLE_MACHINE_CHECK | \
- HID0_ENABLE_INSTRUCTION_CACHE)
-#define CONFIG_SYS_HID2 HID2_HBE
-
-/*
- * MMU Setup
- */
-#define CONFIG_HIGH_BATS 1
-
-/* DDR: cache cacheable */
-#define CONFIG_SYS_SDRAM CONFIG_SYS_SDRAM_BASE
-
-#define CONFIG_SYS_IBAT0L (CONFIG_SYS_SDRAM | BATL_PP_RW |\
- BATL_MEMCOHERENCE)
-#define CONFIG_SYS_IBAT0U (CONFIG_SYS_SDRAM | BATU_BL_256M | BATU_VS |\
- BATU_VP)
-#define CONFIG_SYS_DBAT0L CONFIG_SYS_IBAT0L
-#define CONFIG_SYS_DBAT0U CONFIG_SYS_IBAT0U
-
-/* unused */
-#define CONFIG_SYS_IBAT1L (0)
-#define CONFIG_SYS_IBAT1U (0)
-#define CONFIG_SYS_DBAT1L CONFIG_SYS_IBAT1L
-#define CONFIG_SYS_DBAT1U CONFIG_SYS_IBAT1U
-
-/* IMMRBAR, PCI IO and NAND: cache-inhibit and guarded */
-#define CONFIG_SYS_IBAT2L (CONFIG_SYS_IMMR | BATL_PP_RW |\
- BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
-#define CONFIG_SYS_IBAT2U (CONFIG_SYS_IMMR | BATU_BL_8M | BATU_VS |\
- BATU_VP)
-#define CONFIG_SYS_DBAT2L CONFIG_SYS_IBAT2L
-#define CONFIG_SYS_DBAT2U CONFIG_SYS_IBAT2U
-
-/* unused */
-#define CONFIG_SYS_IBAT3L (0)
-#define CONFIG_SYS_IBAT3U (0)
-#define CONFIG_SYS_DBAT3L CONFIG_SYS_IBAT3L
-#define CONFIG_SYS_DBAT3U CONFIG_SYS_IBAT3U
-
-/* FLASH: icache cacheable, but dcache-inhibit and guarded */
-#define CONFIG_SYS_IBAT4L (CONFIG_SYS_FLASH_BASE | BATL_PP_RW |\
- BATL_MEMCOHERENCE)
-#define CONFIG_SYS_IBAT4U (CONFIG_SYS_FLASH_BASE | BATU_BL_64M |\
- BATU_VS | BATU_VP)
-#define CONFIG_SYS_DBAT4L (CONFIG_SYS_FLASH_BASE | BATL_PP_RW | \
- BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
-#define CONFIG_SYS_DBAT4U CONFIG_SYS_IBAT4U
-
-/* Stack in dcache: cacheable, no memory coherence */
-#define CONFIG_SYS_IBAT5L (CONFIG_SYS_INIT_RAM_ADDR | BATL_PP_RW)
-#define CONFIG_SYS_IBAT5U (CONFIG_SYS_INIT_RAM_ADDR | BATU_BL_128K |\
- BATU_VS | BATU_VP)
-#define CONFIG_SYS_DBAT5L CONFIG_SYS_IBAT5L
-#define CONFIG_SYS_DBAT5U CONFIG_SYS_IBAT5U
-
-/* PCI MEM space: cacheable */
-#define CONFIG_SYS_IBAT6L (CONFIG_SYS_PCI_MEM_PHYS | BATL_PP_RW |\
- BATL_MEMCOHERENCE)
-#define CONFIG_SYS_IBAT6U (CONFIG_SYS_PCI_MEM_PHYS | BATU_BL_256M |\
- BATU_VS | BATU_VP)
-#define CONFIG_SYS_DBAT6L CONFIG_SYS_IBAT6L
-#define CONFIG_SYS_DBAT6U CONFIG_SYS_IBAT6U
-
-/* PCI MMIO space: cache-inhibit and guarded */
-#define CONFIG_SYS_IBAT7L (CONFIG_SYS_PCI_MMIO_PHYS | BATL_PP_RW | \
- BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
-#define CONFIG_SYS_IBAT7U (CONFIG_SYS_PCI_MMIO_PHYS | BATU_BL_256M |\
- BATU_VS | BATU_VP)
-#define CONFIG_SYS_DBAT7L CONFIG_SYS_IBAT7L
-#define CONFIG_SYS_DBAT7U CONFIG_SYS_IBAT7U
-
-/*
- * I2C EEPROM settings
- */
-#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 6
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 10
-#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2
-#define CONFIG_SYS_EEPROM_SIZE 0x4000
-
-/*
- * Environment Configuration
- */
-#define CONFIG_SYS_FLASH_PROTECTION
-#define CONFIG_ENV_OVERWRITE
-#define CONFIG_ENV_IS_IN_FLASH 1
-#define CONFIG_ENV_ADDR 0xFFD00000
-#define CONFIG_ENV_SECT_SIZE 0x20000
-#define CONFIG_ENV_SIZE CONFIG_ENV_SECT_SIZE
-
-/*
- * Video
- */
-#define CONFIG_VIDEO
-#define CONFIG_VIDEO_SM501_PCI
-#define VIDEO_FB_LITTLE_ENDIAN
-#define CONFIG_CMD_BMP
-#define CONFIG_VIDEO_SM501
-#define CONFIG_VIDEO_SM501_32BPP
-#define CONFIG_VIDEO_SM501_FBMEM_OFFSET 0x10000
-#define CONFIG_CFB_CONSOLE
-#define CONFIG_VIDEO_LOGO
-#define CONFIG_VIDEO_BMP_LOGO
-#define CONFIG_VGA_AS_SINGLE_DEVICE
-#define CONFIG_SPLASH_SCREEN
-#define CONFIG_SYS_CONSOLE_IS_IN_ENV
-#define CONFIG_VIDEO_BMP_GZIP
-#define CONFIG_SYS_VIDEO_LOGO_MAX_SIZE (2 << 20)
-
-/*
- * SPI
- */
-#define CONFIG_MPC8XXX_SPI
-
-/*
- * USB
- */
-#define CONFIG_SYS_USB_HOST
-#define CONFIG_USB_EHCI
-#define CONFIG_USB_EHCI_FSL
-#define CONFIG_HAS_FSL_DR_USB
-#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
-
-#define CONFIG_USB_STORAGE
-#define CONFIG_USB_KEYBOARD
-/*
- *
- */
-#define CONFIG_BOOTDELAY 5
-#define CONFIG_AUTOBOOT_KEYED
-#define CONFIG_AUTOBOOT_STOP_STR "s"
-#define CONFIG_ZERO_BOOTDELAY_CHECK
-#define CONFIG_RESET_TO_RETRY 1000
-
-#define MV_CI "MergerBox"
-#define MV_VCI "MergerBox"
-#define MV_FPGA_DATA 0xfc100000
-#define MV_FPGA_SIZE 0x00200000
-
-#define CONFIG_SHOW_BOOT_PROGRESS 1
-
-#define MV_KERNEL_ADDR_RAM 0x02800000
-#define MV_DTB_ADDR_RAM 0x00600000
-#define MV_INITRD_ADDR_RAM 0x01000000
-#define MV_FITADDR 0xfc300000
-#define MV_SPLAH_ADDR 0xffe00000
-
-#define CONFIG_BOOTCOMMAND "run i2c_init;if test ${boot_sqfs} -eq 1;"\
- "then; run fitboot;else;run ubiboot;fi;"
-#define CONFIG_BOOTARGS "console=ttyS0,115200n8"
-
-#define CONFIG_EXTRA_ENV_SETTINGS \
- "console_nr=0\0"\
- "stdin=serial\0"\
- "stdout=serial\0"\
- "stderr=serial\0"\
- "boot_sqfs=1\0"\
- "usb_dr_mode=host\0"\
- "bootfile=MergerBox.fit\0"\
- "baudrate=" __stringify(CONFIG_BAUDRATE) "\0"\
- "fpga=0\0"\
- "fpgadata=" __stringify(MV_FPGA_DATA) "\0"\
- "fpgadatasize=" __stringify(MV_FPGA_SIZE) "\0"\
- "mv_kernel_ram=" __stringify(MV_KERNEL_ADDR_RAM) "\0"\
- "mv_initrd_ram=" __stringify(MV_INITRD_ADDR_RAM) "\0"\
- "mv_dtb_ram=" __stringify(MV_DTB_ADDR_RAM) "\0"\
- "uboota=" __stringify(CONFIG_SYS_TEXT_BASE) "\0"\
- "fitaddr=" __stringify(MV_FITADDR) "\0"\
- "mv_version=" U_BOOT_VERSION "\0"\
- "mtdids=" MTDIDS_DEFAULT "\0"\
- "mtdparts=" MTDPARTS_DEFAULT "\0"\
- "dhcp_client_id=" MV_CI "\0"\
- "dhcp_vendor-class-identifier=" MV_VCI "\0"\
- "upd_uboot=dhcp;tftp bdi2000/u-boot-mergerbox-xp.bin;"\
- "protect off all;erase $uboota +0xC0000;"\
- "cp.b $loadaddr $uboota $filesize\0"\
- "upd_fpga=dhcp;tftp MergerBox.rbf;erase $fpgadata +$fpgadatasize;"\
- "cp.b $loadaddr $fpgadata $filesize\0"\
- "upd_fit=dhcp;tftp MergerBox.fit;erase $fitaddr +0x1000000;"\
- "cp.b $loadaddr $fitaddr $filesize\0"\
- "addsqshrfs=set bootargs $bootargs root=/dev/ram ro "\
- "rootfstype=squashfs\0"\
- "addubirfs=set bootargs $bootargs ubi.mtd=9 root=ubi0:rootfs rw "\
- "rootfstype=ubifs\0"\
- "addusbrfs=set bootargs $bootargs root=/dev/sda1 rw "\
- "rootfstype=ext3 usb-storage.delay_use=1 rootdelay=3\0"\
- "netusbboot=bootp;run fpganetload fitnetload addusbrfs doboot\0"\
- "netubiboot= bootp;run fpganetload fitnetload addubirfs doboot\0"\
- "ubiboot=run fitprep addubirfs;set mv_initrd_ram -;run doboot\0"\
- "doboot=bootm $mv_kernel_ram $mv_initrd_ram $mv_dtb_ram\0"\
- "fitprep=imxtract $fitaddr kernel $mv_kernel_ram;"\
- "imxtract $fitaddr ramdisk $mv_initrd_ram;"\
- "imxtract $fitaddr fdt $mv_dtb_ram\0"\
- "fdtprep=fdt addr $mv_dtb_ram;fdt boardsetup\0"\
- "fitboot=run fitprep fdtprep addsqshrfs doboot\0"\
- "i2c_init=run i2c_speed init_sdi_tx i2c_init_pll\0"\
- "i2c_init_pll=i2c mw 65 9 2;i2c mw 65 9 0;i2c mw 65 5 2b;"\
- "i2c mw 65 7 f;i2c mw 65 8 f;i2c mw 65 11 40;i2c mw 65 12 40;"\
- "i2c mw 65 13 40; i2c mw 65 14 40; i2c mw 65 a 0\0"\
- "i2c_speed=i2c dev 0;i2c speed 300000;i2c dev 1;i2c speed 120000\0"\
- "init_sdi_tx=i2c mw 21 6 0;i2c mw 21 2 0;i2c mw 21 3 0;sleep 1;"\
- "i2c mw 21 2 ff;i2c mw 21 3 3c\0"\
- "splashimage=" __stringify(MV_SPLAH_ADDR) "\0"\
- ""
-
-/*
- * FPGA
- */
-#define CONFIG_FPGA_COUNT 1
-#define CONFIG_FPGA
-#define CONFIG_FPGA_ALTERA
-#define CONFIG_FPGA_CYCLON2
-
-#endif
projects / platform / kernel / u-boot.git / blobdiff