+++ /dev/null
-/*
- * Configuation settings for the Freescale MCF54451 EVB board.
- *
- * Copyright (C) 2004-2008 Freescale Semiconductor, Inc.
- * TsiChung Liew (Tsi-Chung.Liew@freescale.com)
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-/*
- * board/config.h - configuration options, board specific
- */
-
-#ifndef _M54451EVB_H
-#define _M54451EVB_H
-
-/*
- * High Level Configuration Options
- * (easy to change)
- */
-#define CONFIG_M54451EVB /* M54451EVB board */
-
-#define CONFIG_MCFUART
-#define CONFIG_SYS_UART_PORT (0)
-
-#define LDS_BOARD_TEXT board/freescale/m54451evb/sbf_dram_init.o (.text*)
-
-#undef CONFIG_WATCHDOG
-
-#define CONFIG_TIMESTAMP /* Print image info with timestamp */
-
-/*
- * BOOTP options
- */
-#define CONFIG_BOOTP_BOOTFILESIZE
-#define CONFIG_BOOTP_BOOTPATH
-#define CONFIG_BOOTP_GATEWAY
-#define CONFIG_BOOTP_HOSTNAME
-
-/* Network configuration */
-#define CONFIG_MCFFEC
-#ifdef CONFIG_MCFFEC
-# define CONFIG_MII 1
-# define CONFIG_MII_INIT 1
-# define CONFIG_SYS_DISCOVER_PHY
-# define CONFIG_SYS_RX_ETH_BUFFER 8
-# define CONFIG_SYS_FAULT_ECHO_LINK_DOWN
-
-# define CONFIG_SYS_FEC0_PINMUX 0
-# define CONFIG_SYS_FEC0_MIIBASE CONFIG_SYS_FEC0_IOBASE
-# define MCFFEC_TOUT_LOOP 50000
-
-# define CONFIG_ETHPRIME "FEC0"
-# define CONFIG_IPADDR 192.162.1.2
-# define CONFIG_NETMASK 255.255.255.0
-# define CONFIG_SERVERIP 192.162.1.1
-# define CONFIG_GATEWAYIP 192.162.1.1
-
-/* If CONFIG_SYS_DISCOVER_PHY is not defined - hardcoded */
-# ifndef CONFIG_SYS_DISCOVER_PHY
-# define FECDUPLEX FULL
-# define FECSPEED _100BASET
-# else
-# ifndef CONFIG_SYS_FAULT_ECHO_LINK_DOWN
-# define CONFIG_SYS_FAULT_ECHO_LINK_DOWN
-# endif
-# endif /* CONFIG_SYS_DISCOVER_PHY */
-#endif
-
-#define CONFIG_HOSTNAME M54451EVB
-#ifdef CONFIG_SYS_STMICRO_BOOT
-/* ST Micro serial flash */
-#define CONFIG_SYS_LOAD_ADDR2 0x40010007
-#define CONFIG_EXTRA_ENV_SETTINGS \
- "netdev=eth0\0" \
- "inpclk=" __stringify(CONFIG_SYS_INPUT_CLKSRC) "\0" \
- "loadaddr=0x40010000\0" \
- "sbfhdr=sbfhdr.bin\0" \
- "uboot=u-boot.bin\0" \
- "load=tftp ${loadaddr} ${sbfhdr};" \
- "tftp " __stringify(CONFIG_SYS_LOAD_ADDR2) " ${uboot} \0" \
- "upd=run load; run prog\0" \
- "prog=sf probe 0:1 1000000 3;" \
- "sf erase 0 30000;" \
- "sf write ${loadaddr} 0 30000;" \
- "save\0" \
- ""
-#else
-#define CONFIG_SYS_UBOOT_END 0x3FFFF
-#define CONFIG_EXTRA_ENV_SETTINGS \
- "netdev=eth0\0" \
- "inpclk=" __stringify(CONFIG_SYS_INPUT_CLKSRC) "\0" \
- "loadaddr=40010000\0" \
- "u-boot=u-boot.bin\0" \
- "load=tftp ${loadaddr) ${u-boot}\0" \
- "upd=run load; run prog\0" \
- "prog=prot off 0 " __stringify(CONFIG_SYS_UBOOT_END) \
- "; era 0 " __stringify(CONFIG_SYS_UBOOT_END) " ;" \
- "cp.b ${loadaddr} 0 ${filesize};" \
- "save\0" \
- ""
-#endif
-
-/* Realtime clock */
-#define CONFIG_MCFRTC
-#undef RTC_DEBUG
-#define CONFIG_SYS_RTC_OSCILLATOR (32 * CONFIG_SYS_HZ)
-
-/* Timer */
-#define CONFIG_MCFTMR
-#undef CONFIG_MCFPIT
-
-/* I2c */
-#define CONFIG_SYS_I2C
-#define CONFIG_SYS_I2C_FSL
-#define CONFIG_SYS_FSL_I2C_SPEED 80000
-#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F
-#define CONFIG_SYS_FSL_I2C_OFFSET 0x58000
-#define CONFIG_SYS_IMMR CONFIG_SYS_MBAR
-
-/* DSPI and Serial Flash */
-#define CONFIG_CF_SPI
-#define CONFIG_CF_DSPI
-#define CONFIG_SERIAL_FLASH
-#define CONFIG_HARD_SPI
-#define CONFIG_SYS_SBFHDR_SIZE 0x7
-#ifdef CONFIG_CMD_SPI
-
-# define CONFIG_SYS_DSPI_CTAR0 (DSPI_CTAR_TRSZ(7) | \
- DSPI_CTAR_PCSSCK_1CLK | \
- DSPI_CTAR_PASC(0) | \
- DSPI_CTAR_PDT(0) | \
- DSPI_CTAR_CSSCK(0) | \
- DSPI_CTAR_ASC(0) | \
- DSPI_CTAR_DT(1))
-# define CONFIG_SYS_DSPI_CTAR1 (CONFIG_SYS_DSPI_CTAR0)
-# define CONFIG_SYS_DSPI_CTAR2 (CONFIG_SYS_DSPI_CTAR0)
-#endif
-
-/* Input, PCI, Flexbus, and VCO */
-#define CONFIG_EXTRA_CLOCK
-
-#define CONFIG_PRAM 2048 /* 2048 KB */
-
-#define CONFIG_SYS_LONGHELP /* undef to save memory */
-
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
-#else
-#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
-#endif
-#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
-#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
-#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
-
-#define CONFIG_SYS_LOAD_ADDR (CONFIG_SYS_SDRAM_BASE + 0x10000)
-
-#define CONFIG_SYS_MBAR 0xFC000000
-
-/*
- * Low Level Configuration Settings
- * (address mappings, register initial values, etc.)
- * You should know what you are doing if you make changes here.
- */
-
-/*-----------------------------------------------------------------------
- * Definitions for initial stack pointer and data area (in DPRAM)
- */
-#define CONFIG_SYS_INIT_RAM_ADDR 0x80000000
-#define CONFIG_SYS_INIT_RAM_SIZE 0x8000 /* Size of used area in internal SRAM */
-#define CONFIG_SYS_INIT_RAM_CTRL 0x221
-#define CONFIG_SYS_GBL_DATA_OFFSET ((CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) - 32)
-#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
-#define CONFIG_SYS_SBFHDR_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - 32)
-
-/*-----------------------------------------------------------------------
- * Start addresses for the final memory configuration
- * (Set up by the startup code)
- * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0
- */
-#define CONFIG_SYS_SDRAM_BASE 0x40000000
-#define CONFIG_SYS_SDRAM_SIZE 128 /* SDRAM size in MB */
-#define CONFIG_SYS_SDRAM_CFG1 0x33633F30
-#define CONFIG_SYS_SDRAM_CFG2 0x57670000
-#define CONFIG_SYS_SDRAM_CTRL 0xE20D2C00
-#define CONFIG_SYS_SDRAM_EMOD 0x80810000
-#define CONFIG_SYS_SDRAM_MODE 0x008D0000
-#define CONFIG_SYS_SDRAM_DRV_STRENGTH 0x44
-
-#define CONFIG_SYS_MEMTEST_START CONFIG_SYS_SDRAM_BASE + 0x400
-#define CONFIG_SYS_MEMTEST_END ((CONFIG_SYS_SDRAM_SIZE - 3) << 20)
-
-#ifdef CONFIG_CF_SBF
-# define CONFIG_SERIAL_BOOT
-# define CONFIG_SYS_MONITOR_BASE (CONFIG_SYS_TEXT_BASE + 0x400)
-#else
-# define CONFIG_SYS_MONITOR_BASE (CONFIG_SYS_FLASH_BASE + 0x400)
-#endif
-#define CONFIG_SYS_BOOTPARAMS_LEN 64*1024
-#define CONFIG_SYS_MONITOR_LEN (256 << 10) /* Reserve 256 kB for Monitor */
-
-/* Reserve 256 kB for malloc() */
-#define CONFIG_SYS_MALLOC_LEN (256 << 10)
-/*
- * For booting Linux, the board info and command line data
- * have to be in the first 8 MB of memory, since this is
- * the maximum mapped by the Linux kernel during initialization ??
- */
-/* Initial Memory map for Linux */
-#define CONFIG_SYS_BOOTMAPSZ (CONFIG_SYS_SDRAM_BASE + (CONFIG_SYS_SDRAM_SIZE << 20))
-
-/* Configuration for environment
- * Environment is not embedded in u-boot. First time runing may have env
- * crc error warning if there is no correct environment on the flash.
- */
-#if defined(CONFIG_SYS_STMICRO_BOOT)
-# define CONFIG_ENV_SPI_CS 1
-# define CONFIG_ENV_OFFSET 0x20000
-# define CONFIG_ENV_SIZE 0x2000
-# define CONFIG_ENV_SECT_SIZE 0x10000
-#else
-# define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + 0x40000)
-# define CONFIG_ENV_SIZE 0x2000
-# define CONFIG_ENV_SECT_SIZE 0x20000
-#endif
-#undef CONFIG_ENV_OVERWRITE
-
-/* FLASH organization */
-#define CONFIG_SYS_FLASH_BASE CONFIG_SYS_CS0_BASE
-
-#define CONFIG_SYS_FLASH_CFI
-#ifdef CONFIG_SYS_FLASH_CFI
-
-# define CONFIG_FLASH_CFI_DRIVER 1
-# define CONFIG_SYS_FLASH_USE_BUFFER_WRITE 1
-# define CONFIG_SYS_FLASH_SIZE 0x1000000 /* Max size that the board might have */
-# define CONFIG_SYS_FLASH_CFI_WIDTH FLASH_CFI_16BIT
-# define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of memory banks */
-# define CONFIG_SYS_MAX_FLASH_SECT 137 /* max number of sectors on one chip */
-# define CONFIG_SYS_FLASH_PROTECTION /* "Real" (hardware) sectors protection */
-# define CONFIG_SYS_FLASH_CHECKSUM
-# define CONFIG_SYS_FLASH_BANKS_LIST { CONFIG_SYS_CS0_BASE }
-
-#endif
-
-/*
- * This is setting for JFFS2 support in u-boot.
- * NOTE: Enable CONFIG_CMD_JFFS2 for JFFS2 support.
- */
-#ifdef CONFIG_CMD_JFFS2
-# define CONFIG_JFFS2_DEV "nor0"
-# define CONFIG_JFFS2_PART_SIZE 0x01000000
-# define CONFIG_JFFS2_PART_OFFSET (CONFIG_SYS_FLASH0_BASE + 0x500000)
-#endif
-
-/* Cache Configuration */
-#define CONFIG_SYS_CACHELINE_SIZE 16
-
-#define ICACHE_STATUS (CONFIG_SYS_INIT_RAM_ADDR + \
- CONFIG_SYS_INIT_RAM_SIZE - 8)
-#define DCACHE_STATUS (CONFIG_SYS_INIT_RAM_ADDR + \
- CONFIG_SYS_INIT_RAM_SIZE - 4)
-#define CONFIG_SYS_ICACHE_INV (CF_CACR_BCINVA + CF_CACR_ICINVA)
-#define CONFIG_SYS_DCACHE_INV (CF_CACR_DCINVA)
-#define CONFIG_SYS_CACHE_ACR2 (CONFIG_SYS_SDRAM_BASE | \
- CF_ADDRMASK(CONFIG_SYS_SDRAM_SIZE) | \
- CF_ACR_EN | CF_ACR_SM_ALL)
-#define CONFIG_SYS_CACHE_ICACR (CF_CACR_BEC | CF_CACR_IEC | \
- CF_CACR_ICINVA | CF_CACR_EUSP)
-#define CONFIG_SYS_CACHE_DCACR ((CONFIG_SYS_CACHE_ICACR | \
- CF_CACR_DEC | CF_CACR_DDCM_P | \
- CF_CACR_DCINVA) & ~CF_CACR_ICINVA)
-
-/*-----------------------------------------------------------------------
- * Memory bank definitions
- */
-/*
- * CS0 - NOR Flash 16MB
- * CS1 - Available
- * CS2 - Available
- * CS3 - Available
- * CS4 - Available
- * CS5 - Available
- */
-
- /* Flash */
-#define CONFIG_SYS_CS0_BASE 0x00000000
-#define CONFIG_SYS_CS0_MASK 0x00FF0001
-#define CONFIG_SYS_CS0_CTRL 0x00004D80
-
-#define CONFIG_SYS_SPANSION_BASE CONFIG_SYS_CS0_BASE
-
-#endif /* _M54451EVB_H */
projects / platform / kernel / u-boot.git / blobdiff