+++ /dev/null
-/*
- * (C) Copyright 2001
- * Stefan Roese, esd gmbh germany, stefan.roese@esd-electronics.com
- *
- * See file CREDITS for list of people who contributed to this
- * project.
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation; either version 2 of
- * the License, or (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
- */
-
-/*
- * board/config.h - configuration options, board specific
- */
-
-#ifndef __CONFIG_H
-#define __CONFIG_H
-
-/*
- * High Level Configuration Options
- * (easy to change)
- */
-
-#define CONFIG_405GP 1 /* This is a PPC405 CPU */
-#define CONFIG_4xx 1 /* ...member of PPC4xx family */
-#define CONFIG_CPCI405 1 /* ...on a CPCI405 board */
-
-#define CONFIG_BOARD_EARLY_INIT_F 1 /* call board_early_init_f() */
-
-#define CONFIG_SYS_CLK_FREQ 33000000 /* external frequency to pll */
-
-#define CONFIG_BAUDRATE 9600
-#define CONFIG_BOOTDELAY 3 /* autoboot after 3 seconds */
-
-#undef CONFIG_BOOTARGS
-#undef CONFIG_BOOTCOMMAND
-
-#define CONFIG_PREBOOT /* enable preboot variable */
-
-#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
-#define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
-
-#define CONFIG_MII 1 /* MII PHY management */
-#define CONFIG_PHY_ADDR 0 /* PHY address */
-#define CONFIG_LXT971_NO_SLEEP 1 /* disable sleep mode in LXT971 */
-#define CONFIG_RESET_PHY_R 1 /* use reset_phy() to disable phy sleep mode */
-
-#define CONFIG_NET_MULTI 1
-#undef CONFIG_HAS_ETH1
-
-/*
- * BOOTP options
- */
-#define CONFIG_BOOTP_SUBNETMASK
-#define CONFIG_BOOTP_GATEWAY
-#define CONFIG_BOOTP_HOSTNAME
-#define CONFIG_BOOTP_BOOTPATH
-#define CONFIG_BOOTP_DNS
-#define CONFIG_BOOTP_DNS2
-#define CONFIG_BOOTP_SEND_HOSTNAME
-
-
-/*
- * Command line configuration.
- */
-#include <config_cmd_default.h>
-
-#define CONFIG_CMD_DHCP
-#define CONFIG_CMD_PCI
-#define CONFIG_CMD_IRQ
-#define CONFIG_CMD_IDE
-#define CONFIG_CMD_FAT
-#define CONFIG_CMD_ELF
-#define CONFIG_CMD_MII
-#define CONFIG_CMD_EEPROM
-
-
-#define CONFIG_MAC_PARTITION
-#define CONFIG_DOS_PARTITION
-
-#define CONFIG_SUPPORT_VFAT
-
-#undef CONFIG_WATCHDOG /* watchdog disabled */
-
-#define CONFIG_SDRAM_BANK0 1 /* init onboard SDRAM bank 0 */
-
-/*
- * Miscellaneous configurable options
- */
-#define CFG_LONGHELP /* undef to save memory */
-#define CFG_PROMPT "=> " /* Monitor Command Prompt */
-
-#undef CFG_HUSH_PARSER /* use "hush" command parser */
-#ifdef CFG_HUSH_PARSER
-#define CFG_PROMPT_HUSH_PS2 "> "
-#endif
-
-#if defined(CONFIG_CMD_KGDB)
-#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
-#else
-#define CFG_CBSIZE 256 /* Console I/O Buffer Size */
-#endif
-#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
-#define CFG_MAXARGS 16 /* max number of command args */
-#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */
-
-#define CFG_DEVICE_NULLDEV 1 /* include nulldev device */
-
-#define CFG_CONSOLE_INFO_QUIET 1 /* don't print console @ startup*/
-
-#define CFG_MEMTEST_START 0x0400000 /* memtest works on */
-#define CFG_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */
-
-#undef CFG_EXT_SERIAL_CLOCK /* no external serial clock used */
-#define CFG_IGNORE_405_UART_ERRATA_59 /* ignore ppc405gp errata #59 */
-#define CFG_BASE_BAUD 691200
-
-/* The following table includes the supported baudrates */
-#define CFG_BAUDRATE_TABLE \
- { 300, 600, 1200, 2400, 4800, 9600, 19200, 38400, \
- 57600, 115200, 230400, 460800, 921600 }
-
-#define CFG_LOAD_ADDR 0x100000 /* default load address */
-#define CFG_EXTBDINFO 1 /* To use extended board_into (bd_t) */
-
-#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */
-
-#define CONFIG_LOOPW 1 /* enable loopw command */
-
-#define CONFIG_ZERO_BOOTDELAY_CHECK /* check for keypress on bootdelay==0 */
-
-/*-----------------------------------------------------------------------
- * PCI stuff
- *-----------------------------------------------------------------------
- */
-#define PCI_HOST_ADAPTER 0 /* configure as pci adapter */
-#define PCI_HOST_FORCE 1 /* configure as pci host */
-#define PCI_HOST_AUTO 2 /* detected via arbiter enable */
-
-#define CONFIG_PCI /* include pci support */
-#define CONFIG_PCI_HOST PCI_HOST_AUTO /* select pci host function */
-#define CONFIG_PCI_PNP /* do pci plug-and-play */
- /* resource configuration */
-
-#define CONFIG_PCI_SCAN_SHOW /* print pci devices @ startup */
-
-#define CONFIG_PCI_CONFIG_HOST_BRIDGE 1 /* don't skip host bridge config*/
-
-#define CONFIG_PCI_BOOTDELAY 0 /* enable pci bootdelay variable*/
-
-#define CFG_PCI_SUBSYS_VENDORID 0x12FE /* PCI Vendor ID: esd gmbh */
-#define CFG_PCI_SUBSYS_DEVICEID 0x0405 /* PCI Device ID: CPCI-405 */
-#define CFG_PCI_SUBSYS_DEVICEID2 0x0406 /* PCI Device ID: CPCI-405-A */
-#define CFG_PCI_CLASSCODE 0x0b20 /* PCI Class Code: Processor/PPC*/
-#define CFG_PCI_PTM1LA (bd->bi_memstart) /* point to sdram */
-#define CFG_PCI_PTM1MS (~(bd->bi_memsize - 1) | 1) /* memsize, enable hard-wired to 1 */
-#define CFG_PCI_PTM1PCI 0x00000000 /* Host: use this pci address */
-#define CFG_PCI_PTM2LA 0xffc00000 /* point to flash */
-#define CFG_PCI_PTM2MS 0xffc00001 /* 4MB, enable */
-#define CFG_PCI_PTM2PCI 0x04000000 /* Host: use this pci address */
-
-/*-----------------------------------------------------------------------
- * IDE/ATA stuff
- *-----------------------------------------------------------------------
- */
-#undef CONFIG_IDE_8xx_DIRECT /* no pcmcia interface required */
-#undef CONFIG_IDE_LED /* no led for ide supported */
-#undef CONFIG_IDE_RESET /* no reset for ide supported */
-
-#define CFG_IDE_MAXBUS 1 /* max. 1 IDE busses */
-#define CFG_IDE_MAXDEVICE (CFG_IDE_MAXBUS*1) /* max. 1 drives per IDE bus */
-
-#define CFG_ATA_BASE_ADDR 0xF0100000
-#define CFG_ATA_IDE0_OFFSET 0x0000
-
-#define CFG_ATA_DATA_OFFSET 0x0000 /* Offset for data I/O */
-#define CFG_ATA_REG_OFFSET 0x0000 /* Offset for normal register accesses */
-#define CFG_ATA_ALT_OFFSET 0x0000 /* Offset for alternate registers */
-
-/*-----------------------------------------------------------------------
- * Start addresses for the final memory configuration
- * (Set up by the startup code)
- * Please note that CFG_SDRAM_BASE _must_ start at 0
- */
-#define CFG_SDRAM_BASE 0x00000000
-#define CFG_FLASH_BASE 0xFFFD0000
-#define CFG_MONITOR_BASE CFG_FLASH_BASE
-#define CFG_MONITOR_LEN (192 * 1024) /* Reserve 196 kB for Monitor */
-#define CFG_MALLOC_LEN (128 * 1024) /* Reserve 128 kB for malloc() */
-
-/*
- * For booting Linux, the board info and command line data
- * have to be in the first 8 MB of memory, since this is
- * the maximum mapped by the Linux kernel during initialization.
- */
-#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
-/*-----------------------------------------------------------------------
- * FLASH organization
- */
-#define CFG_MAX_FLASH_BANKS 2 /* max number of memory banks */
-#define CFG_MAX_FLASH_SECT 256 /* max number of sectors on one chip */
-
-#define CFG_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */
-#define CFG_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */
-
-#define CFG_FLASH_WORD_SIZE unsigned short /* flash word size (width) */
-#define CFG_FLASH_ADDR0 0x5555 /* 1st address for flash config cycles */
-#define CFG_FLASH_ADDR1 0x2AAA /* 2nd address for flash config cycles */
-/*
- * The following defines are added for buggy IOP480 byte interface.
- * All other boards should use the standard values (CPCI405 etc.)
- */
-#define CFG_FLASH_READ0 0x0000 /* 0 is standard */
-#define CFG_FLASH_READ1 0x0001 /* 1 is standard */
-#define CFG_FLASH_READ2 0x0002 /* 2 is standard */
-
-#define CFG_FLASH_EMPTY_INFO /* print 'E' for empty sector on flinfo */
-
-#define CFG_NVRAM_BASE_ADDR 0xf0200000 /* NVRAM base address */
-#define CFG_NVRAM_SIZE (32*1024) /* NVRAM size */
-#define CFG_VXWORKS_MAC_PTR (CFG_NVRAM_BASE_ADDR+0x6900) /* VxWorks eth-addr*/
-
-#if 1 /* Use NVRAM for environment variables */
-/*-----------------------------------------------------------------------
- * NVRAM organization
- */
-#define CFG_ENV_IS_IN_NVRAM 1 /* use NVRAM for environment vars */
-#define CFG_ENV_SIZE 0x1000 /* Size of Environment vars */
-#define CFG_ENV_ADDR \
- (CFG_NVRAM_BASE_ADDR+CFG_NVRAM_SIZE-CFG_ENV_SIZE) /* Env */
-
-#else /* Use EEPROM for environment variables */
-
-#define CFG_ENV_IS_IN_EEPROM 1 /* use EEPROM for environment vars */
-#define CFG_ENV_OFFSET 0x000 /* environment starts at the beginning of the EEPROM */
-#define CFG_ENV_SIZE 0x400 /* 1024 bytes may be used for env vars */
- /* total size of a CAT24WC08 is 1024 bytes */
-#endif
-
-/*-----------------------------------------------------------------------
- * I2C EEPROM (CAT24WC08) for environment
- */
-#define CONFIG_HARD_I2C /* I2c with hardware support */
-#define CFG_I2C_SPEED 400000 /* I2C speed and slave address */
-#define CFG_I2C_SLAVE 0x7F
-
-#define CFG_I2C_EEPROM_ADDR 0x50 /* EEPROM CAT28WC08 */
-#define CFG_I2C_EEPROM_ADDR_LEN 1 /* Bytes of address */
-/* mask of address bits that overflow into the "EEPROM chip address" */
-#define CFG_I2C_EEPROM_ADDR_OVERFLOW 0x07
-#define CFG_EEPROM_PAGE_WRITE_BITS 4 /* The Catalyst CAT24WC08 has */
- /* 16 byte page write mode using*/
- /* last 4 bits of the address */
-#define CFG_EEPROM_PAGE_WRITE_DELAY_MS 10 /* and takes up to 10 msec */
-#define CFG_EEPROM_PAGE_WRITE_ENABLE
-
-/*
- * Init Memory Controller:
- *
- * BR0/1 and OR0/1 (FLASH)
- */
-
-#define FLASH_BASE0_PRELIM 0xFF800000 /* FLASH bank #0 */
-#define FLASH_BASE1_PRELIM 0xFFC00000 /* FLASH bank #1 */
-
-/*-----------------------------------------------------------------------
- * External Bus Controller (EBC) Setup
- */
-
-/* Memory Bank 0 (Flash Bank 0) initialization */
-#define CFG_EBC_PB0AP 0x92015480
-#define CFG_EBC_PB0CR 0xFFC5A000 /* BAS=0xFFC,BS=4MB,BU=R/W,BW=16bit */
-
-/* Memory Bank 1 (Flash Bank 1) initialization */
-#define CFG_EBC_PB1AP 0x92015480
-#define CFG_EBC_PB1CR 0xFF85A000 /* BAS=0xFF8,BS=4MB,BU=R/W,BW=16bit */
-
-/* Memory Bank 2 (CAN0, 1, 2, Codeswitch) initialization */
-#define CFG_EBC_PB2AP 0x010053C0 /* BWT=2,WBN=1,WBF=1,TH=1,RE=1,SOR=1,BEM=1 */
-#define CFG_EBC_PB2CR 0xF0018000 /* BAS=0xF00,BS=1MB,BU=R/W,BW=8bit */
-
-/* Memory Bank 3 (CompactFlash IDE) initialization */
-#define CFG_EBC_PB3AP 0x010053C0 /* BWT=2,WBN=1,WBF=1,TH=1,RE=1,SOR=1,BEM=1 */
-#define CFG_EBC_PB3CR 0xF011A000 /* BAS=0xF01,BS=1MB,BU=R/W,BW=16bit */
-
-/* Memory Bank 4 (NVRAM) initialization */
-#define CFG_EBC_PB4AP 0x01005280 /* TWT=2,WBN=1,WBF=1,TH=1,SOR=1 */
-#define CFG_EBC_PB4CR 0xF0218000 /* BAS=0xF02,BS=1MB,BU=R/W,BW=8bit */
-
-/* Memory Bank 5 (Quart) initialization */
-#define CFG_EBC_PB5AP 0x04005B80 /* TWT=8,WBN=1,WBF=1,TH=5,RE=1,SOR=1*/
-#define CFG_EBC_PB5CR 0xF0318000 /* BAS=0xF03,BS=1MB,BU=R/W,BW=8bit */
-
-/*-----------------------------------------------------------------------
- * FPGA stuff
- */
-
-/* FPGA program pin configuration */
-#define CFG_FPGA_PRG 0x04000000 /* FPGA program pin (ppc output) */
-#define CFG_FPGA_CLK 0x02000000 /* FPGA clk pin (ppc output) */
-#define CFG_FPGA_DATA 0x01000000 /* FPGA data pin (ppc output) */
-#define CFG_FPGA_INIT 0x00400000 /* FPGA init pin (ppc input) */
-#define CFG_FPGA_DONE 0x00800000 /* FPGA done pin (ppc input) */
-
-/*-----------------------------------------------------------------------
- * Definitions for initial stack pointer and data area (in data cache)
- */
-#if 1 /* test-only */
-#define CFG_INIT_DCACHE_CS 7 /* use cs # 7 for data cache memory */
-
-#define CFG_INIT_RAM_ADDR 0x40000000 /* use data cache */
-#else
-#define CFG_INIT_RAM_ADDR 0x00df0000 /* inside of SDRAM */
-#endif
-#define CFG_INIT_RAM_END 0x2000 /* End of used area in RAM */
-#define CFG_GBL_DATA_SIZE 128 /* size in bytes reserved for initial data */
-#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
-#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET
-
-
-/*
- * Internal Definitions
- *
- * Boot Flags
- */
-#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */
-#define BOOTFLAG_WARM 0x02 /* Software reboot */
-
-#endif /* __CONFIG_H */
projects / platform / kernel / u-boot.git / blobdiff