+++ /dev/null
-/* SPDX-License-Identifier: GPL-2.0+ */
-/*
- * Copyright 2011-2012 Freescale Semiconductor, Inc.
- */
-
-/*
- * BSC9131 RDB board configuration file
- */
-
-#ifndef __CONFIG_H
-#define __CONFIG_H
-
-#define CONFIG_NAND_FSL_IFC
-
-#ifdef CONFIG_SPIFLASH
-#define CONFIG_RAMBOOT_SPIFLASH
-#define CONFIG_SYS_RAMBOOT
-#define CONFIG_RESET_VECTOR_ADDRESS 0x110bfffc
-#endif
-
-#ifdef CONFIG_NAND
-#define CONFIG_SPL_INIT_MINIMAL
-#define CONFIG_SPL_FLUSH_IMAGE
-#define CONFIG_SPL_TARGET "u-boot-with-spl.bin"
-
-#define CONFIG_SPL_MAX_SIZE 8192
-#define CONFIG_SPL_RELOC_TEXT_BASE 0x00100000
-#define CONFIG_SPL_RELOC_STACK 0x00100000
-#define CONFIG_SYS_NAND_U_BOOT_SIZE ((768 << 10) - 0x2000)
-#define CONFIG_SYS_NAND_U_BOOT_DST (0x00200000 - CONFIG_SPL_MAX_SIZE)
-#define CONFIG_SYS_NAND_U_BOOT_START 0x00200000
-#define CONFIG_SYS_NAND_U_BOOT_OFFS 0
-#endif
-
-#ifdef CONFIG_SPL_BUILD
-#define CONFIG_SYS_MONITOR_BASE CONFIG_SPL_TEXT_BASE
-#else
-#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */
-#endif
-
-/* High Level Configuration Options */
-
-#define CONFIG_ENV_OVERWRITE
-
-#define CONFIG_DDR_CLK_FREQ 66666666 /* DDRCLK on 9131 RDB */
-#if defined(CONFIG_SYS_CLK_100)
-#define CONFIG_SYS_CLK_FREQ 100000000 /* SYSCLK for 9131 RDB */
-#else
-#define CONFIG_SYS_CLK_FREQ 66666666 /* SYSCLK for 9131 RDB */
-#endif
-
-#define CONFIG_HWCONFIG
-/*
- * These can be toggled for performance analysis, otherwise use default.
- */
-#define CONFIG_L2_CACHE /* toggle L2 cache */
-#define CONFIG_BTB /* enable branch predition */
-
-#define CONFIG_SYS_MEMTEST_START 0x01000000 /* memtest works on */
-#define CONFIG_SYS_MEMTEST_END 0x01ffffff
-
-/* DDR Setup */
-#undef CONFIG_SYS_DDR_RAW_TIMING
-#undef CONFIG_DDR_SPD
-#define CONFIG_SYS_SPD_BUS_NUM 0
-#define SPD_EEPROM_ADDRESS 0x52 /* I2C access */
-
-#define CONFIG_MEM_INIT_VALUE 0xDeadBeef
-
-#ifndef __ASSEMBLY__
-extern unsigned long get_sdram_size(void);
-#endif
-#define CONFIG_SYS_SDRAM_SIZE get_sdram_size() /* DDR size */
-#define CONFIG_SYS_DDR_SDRAM_BASE 0x00000000
-#define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE
-
-#define CONFIG_DIMM_SLOTS_PER_CTLR 1
-#define CONFIG_CHIP_SELECTS_PER_CTRL 1
-
-#define CONFIG_SYS_DDR_CS0_BNDS 0x0000003f
-#define CONFIG_SYS_DDR_CS0_CONFIG 0x80014302
-#define CONFIG_SYS_DDR_CS0_CONFIG_2 0x00000000
-
-#define CONFIG_SYS_DDR_DATA_INIT 0xdeadbeef
-#define CONFIG_SYS_DDR_INIT_ADDR 0x00000000
-#define CONFIG_SYS_DDR_INIT_EXT_ADDR 0x00000000
-#define CONFIG_SYS_DDR_MODE_CONTROL 0x00000000
-
-#define CONFIG_SYS_DDR_ZQ_CONTROL 0x89080600
-#define CONFIG_SYS_DDR_SR_CNTR 0x00000000
-#define CONFIG_SYS_DDR_RCW_1 0x00000000
-#define CONFIG_SYS_DDR_RCW_2 0x00000000
-#define CONFIG_SYS_DDR_CONTROL 0xC70C0000 /* Type = DDR3 */
-#define CONFIG_SYS_DDR_CONTROL_2 0x24401000
-#define CONFIG_SYS_DDR_TIMING_4 0x00000001
-#define CONFIG_SYS_DDR_TIMING_5 0x02401400
-
-#define CONFIG_SYS_DDR_TIMING_3_800 0x00030000
-#define CONFIG_SYS_DDR_TIMING_0_800 0x00110104
-#define CONFIG_SYS_DDR_TIMING_1_800 0x6f6b8644
-#define CONFIG_SYS_DDR_TIMING_2_800 0x0fa888cf
-#define CONFIG_SYS_DDR_CLK_CTRL_800 0x03000000
-#define CONFIG_SYS_DDR_MODE_1_800 0x00441420
-#define CONFIG_SYS_DDR_MODE_2_800 0x8000c000
-#define CONFIG_SYS_DDR_INTERVAL_800 0x0c300100
-#define CONFIG_SYS_DDR_WRLVL_CONTROL_800 0x8675f608
-
-/*
- * Base addresses -- Note these are effective addresses where the
- * actual resources get mapped (not physical addresses)
- */
-/* relocated CCSRBAR */
-#define CONFIG_SYS_CCSRBAR CONFIG_SYS_CCSRBAR_DEFAULT
-#define CONFIG_SYS_CCSRBAR_PHYS_LOW CONFIG_SYS_CCSRBAR_DEFAULT
-
-#define CONFIG_SYS_IMMR CONFIG_SYS_CCSRBAR /* PQII uses */
- /* CONFIG_SYS_IMMR */
-/* DSP CCSRBAR */
-#define CONFIG_SYS_FSL_DSP_CCSRBAR CONFIG_SYS_FSL_DSP_CCSRBAR_DEFAULT
-#define CONFIG_SYS_FSL_DSP_CCSRBAR_PHYS CONFIG_SYS_FSL_DSP_CCSRBAR_DEFAULT
-
-/*
- * Memory map
- *
- * 0x0000_0000 0x3FFF_FFFF DDR 1G cacheable
- * 0x8800_0000 0x8810_0000 IFC internal SRAM 1M
- * 0xB000_0000 0xB0FF_FFFF DSP core M2 memory 16M
- * 0xC100_0000 0xC13F_FFFF MAPLE-2F 4M
- * 0xC1F0_0000 0xC1F3_FFFF PA L2 SRAM Region 0 256K
- * 0xC1F8_0000 0xC1F9_FFFF PA L2 SRAM Region 1 128K
- * 0xFED0_0000 0xFED0_3FFF SEC Secured RAM 16K
- * 0xFF60_0000 0xFF6F_FFFF DSP CCSR 1M
- * 0xFF70_0000 0xFF7F_FFFF PA CCSR 1M
- * 0xFF80_0000 0xFFFF_FFFF Boot Page & NAND flash buffer 8M
- *
- */
-
-/*
- * IFC Definitions
- */
-
-/* NAND Flash on IFC */
-#define CONFIG_SYS_NAND_BASE 0xff800000
-#define CONFIG_SYS_NAND_BASE_PHYS CONFIG_SYS_NAND_BASE
-
-#define CONFIG_SYS_NAND_CSPR (CSPR_PHYS_ADDR(CONFIG_SYS_NAND_BASE_PHYS) \
- | CSPR_PORT_SIZE_8 /* Port Size = 8 bit*/ \
- | CSPR_MSEL_NAND /* MSEL = NAND */ \
- | CSPR_V)
-#define CONFIG_SYS_NAND_AMASK IFC_AMASK(64*1024)
-
-#define CONFIG_SYS_NAND_CSOR (CSOR_NAND_ECC_ENC_EN /* ECC on encode */ \
- | CSOR_NAND_ECC_DEC_EN /* ECC on decode */ \
- | CSOR_NAND_ECC_MODE_4 /* 4-bit ECC */ \
- | CSOR_NAND_RAL_2 /* RAL = 2Byes */ \
- | CSOR_NAND_PGS_2K /* Page Size = 2K */ \
- | CSOR_NAND_SPRZ_64 /* Spare size = 64 */ \
- | CSOR_NAND_PB(64)) /*Pages Per Block = 64*/
-
-/* NAND Flash Timing Params */
-#define CONFIG_SYS_NAND_FTIM0 (FTIM0_NAND_TCCST(0x03) \
- | FTIM0_NAND_TWP(0x05) \
- | FTIM0_NAND_TWCHT(0x02) \
- | FTIM0_NAND_TWH(0x04))
-#define CONFIG_SYS_NAND_FTIM1 (FTIM1_NAND_TADLE(0x1C) \
- | FTIM1_NAND_TWBE(0x1E) \
- | FTIM1_NAND_TRR(0x07) \
- | FTIM1_NAND_TRP(0x05))
-#define CONFIG_SYS_NAND_FTIM2 (FTIM2_NAND_TRAD(0x08) \
- | FTIM2_NAND_TREH(0x04) \
- | FTIM2_NAND_TWHRE(0x11))
-#define CONFIG_SYS_NAND_FTIM3 FTIM3_NAND_TWW(0x04)
-
-#define CONFIG_SYS_NAND_BASE_LIST { CONFIG_SYS_NAND_BASE }
-#define CONFIG_SYS_MAX_NAND_DEVICE 1
-#define CONFIG_SYS_NAND_BLOCK_SIZE (128 * 1024)
-
-#define CONFIG_SYS_NAND_DDR_LAW 11
-
-/* Set up IFC registers for boot location NAND */
-#define CONFIG_SYS_CSPR0 CONFIG_SYS_NAND_CSPR
-#define CONFIG_SYS_AMASK0 CONFIG_SYS_NAND_AMASK
-#define CONFIG_SYS_CSOR0 CONFIG_SYS_NAND_CSOR
-#define CONFIG_SYS_CS0_FTIM0 CONFIG_SYS_NAND_FTIM0
-#define CONFIG_SYS_CS0_FTIM1 CONFIG_SYS_NAND_FTIM1
-#define CONFIG_SYS_CS0_FTIM2 CONFIG_SYS_NAND_FTIM2
-#define CONFIG_SYS_CS0_FTIM3 CONFIG_SYS_NAND_FTIM3
-
-#define CONFIG_SYS_INIT_RAM_LOCK
-#define CONFIG_SYS_INIT_RAM_ADDR 0xffd00000 /* stack in RAM */
-#define CONFIG_SYS_INIT_RAM_SIZE 0x00004000/* End of used area in RAM */
-
-#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE \
- - GENERATED_GBL_DATA_SIZE)
-#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
-
-#define CONFIG_SYS_MONITOR_LEN (768 * 1024)
-#define CONFIG_SYS_MALLOC_LEN (1024 * 1024) /* Reserved for malloc*/
-
-/* Serial Port */
-#undef CONFIG_SERIAL_SOFTWARE_FIFO
-#define CONFIG_SYS_NS16550_SERIAL
-#define CONFIG_SYS_NS16550_REG_SIZE 1
-#define CONFIG_SYS_NS16550_CLK get_bus_freq(0)
-#ifdef CONFIG_SPL_BUILD
-#define CONFIG_NS16550_MIN_FUNCTIONS
-#endif
-
-#define CONFIG_SYS_BAUDRATE_TABLE \
- {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200}
-
-#define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_CCSRBAR+0x4500)
-
-#define CONFIG_SYS_I2C
-#define CONFIG_SYS_I2C_FSL
-#define CONFIG_SYS_FSL_I2C_SPEED 400000
-#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F
-#define CONFIG_SYS_FSL_I2C_OFFSET 0x3000
-
-/* I2C EEPROM */
-#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 3
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 5
-
-/* eSPI - Enhanced SPI */
-
-#if defined(CONFIG_TSEC_ENET)
-
-#define CONFIG_MII_DEFAULT_TSEC 1 /* Allow unregistered phys */
-#define CONFIG_TSEC1 1
-#define CONFIG_TSEC1_NAME "eTSEC1"
-#define CONFIG_TSEC2 1
-#define CONFIG_TSEC2_NAME "eTSEC2"
-
-#define TSEC1_PHY_ADDR 0
-#define TSEC2_PHY_ADDR 3
-
-#define TSEC1_FLAGS (TSEC_GIGABIT | TSEC_REDUCED)
-#define TSEC2_FLAGS (TSEC_GIGABIT | TSEC_REDUCED)
-
-#define TSEC1_PHYIDX 0
-
-#define TSEC2_PHYIDX 0
-
-#define CONFIG_ETHPRIME "eTSEC1"
-
-#endif /* CONFIG_TSEC_ENET */
-
-/*
- * Environment
- */
-#if defined(CONFIG_RAMBOOT_SPIFLASH)
-#elif defined(CONFIG_NAND)
-#define CONFIG_ENV_RANGE (3 * CONFIG_ENV_SIZE)
-#endif
-
-#define CONFIG_LOADS_ECHO /* echo on for serial download */
-#define CONFIG_SYS_LOADS_BAUD_CHANGE /* allow baudrate change */
-
-/*
- * Miscellaneous configurable options
- */
-#define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */
-
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
-#else
-#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
-#endif
-#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE/* Boot Argument Buffer Size */
-
-/*
- * For booting Linux, the board info and command line data
- * have to be in the first 64 MB of memory, since this is
- * the maximum mapped by the Linux kernel during initialization.
- */
-#define CONFIG_SYS_BOOTMAPSZ (64 << 20) /* Initial Memory map for Linux */
-#define CONFIG_SYS_BOOTM_LEN (64 << 20) /* Increase max gunzip size */
-
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */
-#endif
-
-#ifdef CONFIG_USB_EHCI_HCD
-#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
-#define CONFIG_USB_EHCI_FSL
-#define CONFIG_HAS_FSL_DR_USB
-#endif
-
-/*
- * Dynamic MTD Partition support with mtdparts
- */
-
-/*
- * Environment Configuration
- */
-
-#if defined(CONFIG_TSEC_ENET)
-#define CONFIG_HAS_ETH0
-#endif
-
-#define CONFIG_HOSTNAME "BSC9131rdb"
-#define CONFIG_ROOTPATH "/opt/nfsroot"
-#define CONFIG_BOOTFILE "uImage"
-#define CONFIG_UBOOTPATH "u-boot.bin" /* U-Boot image on TFTP server */
-
-#define CONFIG_EXTRA_ENV_SETTINGS \
- "netdev=eth0\0" \
- "uboot=" CONFIG_UBOOTPATH "\0" \
- "loadaddr=1000000\0" \
- "bootfile=uImage\0" \
- "consoledev=ttyS0\0" \
- "ramdiskaddr=2000000\0" \
- "ramdiskfile=rootfs.ext2.gz.uboot\0" \
- "fdtaddr=1e00000\0" \
- "fdtfile=bsc9131rdb.dtb\0" \
- "bdev=sda1\0" \
- "hwconfig=usb1:dr_mode=host,phy_type=ulpi\0" \
- "bootm_size=0x37000000\0" \
- "othbootargs=ramdisk_size=600000 " \
- "default_hugepagesz=256m hugepagesz=256m hugepages=1\0" \
- "usbext2boot=setenv bootargs root=/dev/ram rw " \
- "console=$consoledev,$baudrate $othbootargs; " \
- "usb start;" \
- "ext2load usb 0:4 $loadaddr $bootfile;" \
- "ext2load usb 0:4 $fdtaddr $fdtfile;" \
- "ext2load usb 0:4 $ramdiskaddr $ramdiskfile;" \
- "bootm $loadaddr $ramdiskaddr $fdtaddr\0" \
-
-#define CONFIG_RAMBOOTCOMMAND \
- "setenv bootargs root=/dev/ram rw " \
- "console=$consoledev,$baudrate $othbootargs; " \
- "tftp $ramdiskaddr $ramdiskfile;" \
- "tftp $loadaddr $bootfile;" \
- "tftp $fdtaddr $fdtfile;" \
- "bootm $loadaddr $ramdiskaddr $fdtaddr"
-
-#define CONFIG_BOOTCOMMAND CONFIG_RAMBOOTCOMMAND
-
-#endif /* __CONFIG_H */
projects / platform / kernel / u-boot.git / blobdiff