rename CFG_ macros to CONFIG_SYS

[platform/kernel/u-boot.git] / doc / README.m5373evb

diff --git a/doc/README.m5373evb b/doc/README.m5373evb
index b2ef4a5..4781d94 100644 (file)
--- a/doc/README.m5373evb
+++ b/doc/README.m5373evb
@@ -67,12 +67,12 @@ CONFIG_M5373                -- define for all Freescale MCF5373 CPUs
 CONFIG_M5373EVB                -- define for M5373EVB board
 
 CONFIG_MCFUART         -- define to use common CF Uart driver
-CFG_UART_PORT          -- define UART port number, start with 0, 1 and 2
+CONFIG_SYS_UART_PORT           -- define UART port number, start with 0, 1 and 2
 CONFIG_BAUDRATE                -- define UART baudrate
 
 CONFIG_MCFRTC          -- define to use common CF RTC driver
-CFG_MCFRTC_BASE                -- provide base address for RTC in immap.h
-CFG_RTC_OSCILLATOR     -- define RTC clock frequency
+CONFIG_SYS_MCFRTC_BASE         -- provide base address for RTC in immap.h
+CONFIG_SYS_RTC_OSCILLATOR      -- define RTC clock frequency
 RTC_DEBUG              -- define to show RTC debug message
 CONFIG_CMD_DATE                -- enable to use date feature in u-boot
 
@@ -80,11 +80,11 @@ CONFIG_MCFFEC               -- define to use common CF FEC driver
 CONFIG_NET_MULTI       -- define to use multi FEC in u-boot
 CONFIG_MII             -- enable to use MII driver
 CONFIG_CF_DOMII                -- enable to use MII feature in cmd_mii.c
-CFG_DISCOVER_PHY       -- enable PHY discovery
-CFG_RX_ETH_BUFFER      -- Set FEC Receive buffer
-CFG_FAULT_ECHO_LINK_DOWN--
-CFG_FEC0_PINMUX                -- Set FEC0 Pin configuration
-CFG_FEC0_MIIBASE       -- Set FEC0 MII base register
+CONFIG_SYS_DISCOVER_PHY        -- enable PHY discovery
+CONFIG_SYS_RX_ETH_BUFFER       -- Set FEC Receive buffer
+CONFIG_SYS_FAULT_ECHO_LINK_DOWN--
+CONFIG_SYS_FEC0_PINMUX         -- Set FEC0 Pin configuration
+CONFIG_SYS_FEC0_MIIBASE        -- Set FEC0 MII base register
 MCFFEC_TOUT_LOOP       -- set FEC timeout loop
 
 CONFIG_MCFTMR          -- define to use DMA timer
@@ -93,22 +93,22 @@ CONFIG_MCFPIT               -- define to use PIT timer
 CONFIG_FSL_I2C         -- define to use FSL common I2C driver
 CONFIG_HARD_I2C                -- define for I2C hardware support
 CONFIG_SOFT_I2C                -- define for I2C bit-banged
-CFG_I2C_SPEED          -- define for I2C speed
-CFG_I2C_SLAVE          -- define for I2C slave address
-CFG_I2C_OFFSET         -- define for I2C base address offset
-CFG_IMMR               -- define for MBAR offset
+CONFIG_SYS_I2C_SPEED           -- define for I2C speed
+CONFIG_SYS_I2C_SLAVE           -- define for I2C slave address
+CONFIG_SYS_I2C_OFFSET          -- define for I2C base address offset
+CONFIG_SYS_IMMR                -- define for MBAR offset
 
-CFG_MBAR               -- define MBAR offset
+CONFIG_SYS_MBAR                -- define MBAR offset
 
 CONFIG_MONITOR_IS_IN_RAM -- Not support
 
-CFG_INIT_RAM_ADDR      -- defines the base address of the MCF5373 internal SRAM
+CONFIG_SYS_INIT_RAM_ADDR       -- defines the base address of the MCF5373 internal SRAM
 
-CFG_CSn_BASE   -- defines the Chip Select Base register
-CFG_CSn_MASK   -- defines the Chip Select Mask register
-CFG_CSn_CTRL   -- defines the Chip Select Control register
+CONFIG_SYS_CSn_BASE    -- defines the Chip Select Base register
+CONFIG_SYS_CSn_MASK    -- defines the Chip Select Mask register
+CONFIG_SYS_CSn_CTRL    -- defines the Chip Select Control register
 
-CFG_SDRAM_BASE -- defines the DRAM Base
+CONFIG_SYS_SDRAM_BASE  -- defines the DRAM Base
 
 2. MEMORY MAP UNDER U-BOOT AND LINUX KERNEL
 ===========================================