mpc8xx: remove FPS{850, 860}L, NSCU, SM850, TK885D, virtlab2 support

[platform/kernel/u-boot.git] / board / tqc / tqm8xx / tqm8xx.c

diff --git a/board/tqc/tqm8xx/tqm8xx.c b/board/tqc/tqm8xx/tqm8xx.c
index 3b5230a..6d17830 100644 (file)
--- a/board/tqc/tqm8xx/tqm8xx.c
+++ b/board/tqc/tqm8xx/tqm8xx.c
@@ -118,9 +118,7 @@ int checkboard (void)
                        break;
                putc (buf[i]);
        }
-#ifdef CONFIG_VIRTLAB2
-       puts (" (Virtlab2)");
-#endif
+
        putc ('\n');
 
        return (0);
@@ -512,14 +510,6 @@ int misc_init_r (void)
        immap->im_ioport.iop_padat &= ~0x0001;  /* turn it off */
 # endif
 
-#ifdef CONFIG_NSCU
-       /* wake up ethernet module */
-       immap->im_ioport.iop_pcpar &= ~0x0004;  /* GPIO pin      */
-       immap->im_ioport.iop_pcdir |= 0x0004;   /* output        */
-       immap->im_ioport.iop_pcso &= ~0x0004;   /* for clarity   */
-       immap->im_ioport.iop_pcdat |= 0x0004;   /* enable        */
-#endif /* CONFIG_NSCU */
-
        return (0);
 }
 #endif /* CONFIG_MISC_INIT_R */
@@ -682,49 +672,3 @@ int ft_board_setup(void *blob, bd_t *bd)
        return 0;
 }
 #endif /* defined(CONFIG_OF_BOARD_SETUP) && defined(CONFIG_OF_LIBFDT) */
-
-/* ---------------------------------------------------------------------------- */
-/* TK885D specific initializaion                                               */
-/* ---------------------------------------------------------------------------- */
-#ifdef CONFIG_TK885D
-#include <miiphy.h>
-int last_stage_init(void)
-{
-       const unsigned char phy[] = {CONFIG_FEC1_PHY, CONFIG_FEC2_PHY};
-       unsigned short reg;
-       int ret, i = 100;
-       char *s;
-
-       mii_init();
-       /* Without this delay 0xff is read from the UART buffer later in
-        * abortboot() and autoboot is aborted */
-       udelay(10000);
-       while (tstc() && i--)
-               (void)getc();
-
-       /* Check if auto-negotiation is prohibited */
-       s = getenv("phy_auto_nego");
-
-       if (!s || !strcmp(s, "on"))
-               /* Nothing to do - autonegotiation by default */
-               return 0;
-
-       for (i = 0; i < 2; i++) {
-               ret = miiphy_read("FEC", phy[i], MII_BMCR, &reg);
-               if (ret) {
-                       printf("Cannot read BMCR on PHY %d\n", phy[i]);
-                       return 0;
-               }
-               /* Auto-negotiation off, hard set full duplex, 100Mbps */
-               ret = miiphy_write("FEC", phy[i],
-                                  MII_BMCR, (reg | BMCR_SPEED100 |
-                                             BMCR_FULLDPLX) & ~BMCR_ANENABLE);
-               if (ret) {
-                       printf("Cannot write BMCR on PHY %d\n", phy[i]);
-                       return 0;
-               }
-       }
-
-       return 0;
-}
-#endif