rename CFG_ macros to CONFIG_SYS

[platform/kernel/u-boot.git] / board / sandburst / metrobox / metrobox.c

diff --git a/board/sandburst/metrobox/metrobox.c b/board/sandburst/metrobox/metrobox.c
index c38850d..c3c4459 100644 (file)
--- a/board/sandburst/metrobox/metrobox.c
+++ b/board/sandburst/metrobox/metrobox.c
@@ -55,7 +55,7 @@ int board_early_init_f (void)
        mtsdr(sdr_pfc0, 0x00103E00);
 
        /* Setup access for LEDs, and system topology info */
-       gpio_regs = (ppc440_gpio_regs_t *)CFG_GPIO_BASE;
+       gpio_regs = (ppc440_gpio_regs_t *)CONFIG_SYS_GPIO_BASE;
        gpio_regs->open_drain = SBCOMMON_GPIO_SYS_LEDS;
        gpio_regs->tri_state  = SBCOMMON_GPIO_DBGLEDS;
 
@@ -83,7 +83,7 @@ int board_early_init_f (void)
              EBC_BXAP_RE_DISABLED  | EBC_BXAP_BEM_WRITEONLY |
              EBC_BXAP_PEN_DISABLED);
 
-       mtebc(pb0cr, EBC_BXCR_BAS_ENCODE(CFG_FLASH_BASE) |
+       mtebc(pb0cr, EBC_BXCR_BAS_ENCODE(CONFIG_SYS_FLASH_BASE) |
              EBC_BXCR_BS_1MB | EBC_BXCR_BU_RW | EBC_BXCR_BW_8BIT);
        /*--------------------------------------------------------------------+
          | 8KB NVRAM/RTC. Initialize bank 1 with default values.
@@ -246,7 +246,7 @@ int checkboard (void)
        unsigned char opto_rev, opto_id;
        OPTO_FPGA_REGS_ST *opto_ps;
 
-       opto_ps = (OPTO_FPGA_REGS_ST *)CFG_FPGA_BASE;
+       opto_ps = (OPTO_FPGA_REGS_ST *)CONFIG_SYS_FPGA_BASE;
 
        opto_rev = (unsigned char)((opto_ps->revision_ul &
                                    SAND_HAL_XC_XCVR_CNTL_REVISION_REVISION_MASK)
@@ -286,7 +286,7 @@ int checkboard (void)
 
        /* Fix the ack in the bme 32 */
        udelay(5000);
-       out32(CFG_BME32_BASE + 0x0000000C, 0x00000001);
+       out32(CONFIG_SYS_BME32_BASE + 0x0000000C, 0x00000001);
        asm("eieio");
 
 
@@ -302,7 +302,7 @@ int misc_init_f (void)
 {
        /* Turn on i2c bus 1 */
        puts ("I2C1:  ");
-       i2c1_init (CFG_I2C_SPEED, CFG_I2C_SLAVE);
+       i2c1_init (CONFIG_SYS_I2C_SPEED, CONFIG_SYS_I2C_SLAVE);
        puts ("ready\n");
 
        /* Turn on fans */
@@ -323,7 +323,7 @@ int misc_init_r (void)
        unsigned char opto_rev;
        OPTO_FPGA_REGS_ST *opto_ps;
 
-       opto_ps = (OPTO_FPGA_REGS_ST *)CFG_FPGA_BASE;
+       opto_ps = (OPTO_FPGA_REGS_ST *)CONFIG_SYS_FPGA_BASE;
 
        if(NULL != getenv("secondserial")) {
            puts("secondserial is set, switching to second serial port\n");
@@ -387,7 +387,7 @@ int misc_init_r (void)
 void ide_set_reset(int on)
 {
        OPTO_FPGA_REGS_ST *opto_ps;
-       opto_ps = (OPTO_FPGA_REGS_ST *)CFG_FPGA_BASE;
+       opto_ps = (OPTO_FPGA_REGS_ST *)CONFIG_SYS_FPGA_BASE;
 
        if (on) {               /* assert RESET */
            opto_ps->reset_ul &= ~SAND_HAL_XC_XCVR_CNTL_RESET_CF_RESET_N_MASK;
@@ -412,7 +412,7 @@ void fpga_init(void)
        /*
         * Take appropriate hw bits out of reset
         */
-       opto_ps = (OPTO_FPGA_REGS_ST *)CFG_FPGA_BASE;
+       opto_ps = (OPTO_FPGA_REGS_ST *)CONFIG_SYS_FPGA_BASE;
 
        tmp =
            SAND_HAL_XC_XCVR_CNTL_RESET_MAC1_RESET_N_MASK |