rename CFG_ macros to CONFIG_SYS

[platform/kernel/u-boot.git] / board / sandburst / common / sb_common.c

diff --git a/board/sandburst/common/sb_common.c b/board/sandburst/common/sb_common.c
index 51b1c75..f6ea16f 100644 (file)
--- a/board/sandburst/common/sb_common.c
+++ b/board/sandburst/common/sb_common.c
@@ -43,7 +43,7 @@ int sbcommon_get_master(void)
 {
        ppc440_gpio_regs_t *gpio_regs;
 
-       gpio_regs = (ppc440_gpio_regs_t *)CFG_GPIO_BASE;
+       gpio_regs = (ppc440_gpio_regs_t *)CONFIG_SYS_GPIO_BASE;
 
        if (gpio_regs->in & SBCOMMON_GPIO_PRI_N) {
                return 0;
@@ -63,7 +63,7 @@ int sbcommon_secondary_present(void)
 {
        ppc440_gpio_regs_t *gpio_regs;
 
-       gpio_regs = (ppc440_gpio_regs_t *)CFG_GPIO_BASE;
+       gpio_regs = (ppc440_gpio_regs_t *)CONFIG_SYS_GPIO_BASE;
 
        if (gpio_regs->in & SBCOMMON_GPIO_SEC_PRES)
                return 0;
@@ -84,7 +84,7 @@ unsigned short sbcommon_get_serial_number(void)
 
        /* Get the board serial number from eeprom */
        /* Initialize I2C */
-       i2c_init (CFG_I2C_SPEED, CFG_I2C_SLAVE);
+       i2c_init (CONFIG_SYS_I2C_SPEED, CONFIG_SYS_I2C_SLAVE);
 
        /* Read 256 bytes in EEPROM */
        i2c_read (0x50, 0, 1, buff, 0x100);
@@ -218,11 +218,11 @@ phys_size_t initdram (int board_type)
  *
  *
  ************************************************************************/
-#if defined(CFG_DRAM_TEST)
+#if defined(CONFIG_SYS_DRAM_TEST)
 int testdram (void)
 {
-       uint *pstart = (uint *) CFG_MEMTEST_START;
-       uint *pend = (uint *) CFG_MEMTEST_END;
+       uint *pstart = (uint *) CONFIG_SYS_MEMTEST_START;
+       uint *pend = (uint *) CONFIG_SYS_MEMTEST_END;
        uint *p;
 
        printf("Testing SDRAM: ");
@@ -340,7 +340,7 @@ int pci_pre_init(struct pci_controller * hose )
  *     may not be sufficient for a given board.
  *
  ************************************************************************/
-#if defined(CONFIG_PCI) && defined(CFG_PCI_TARGET_INIT)
+#if defined(CONFIG_PCI) && defined(CONFIG_SYS_PCI_TARGET_INIT)
 void pci_target_init(struct pci_controller * hose )
 {
        /*--------------------------------------------------------------------------+
@@ -355,7 +355,7 @@ void pci_target_init(struct pci_controller * hose )
         * Map all of SDRAM to PCI address 0x0000_0000. Note that the 440 strapping
         * options to not support sizes such as 128/256 MB.
         *--------------------------------------------------------------------------*/
-       out32r( PCIX0_PIM0LAL, CFG_SDRAM_BASE );
+       out32r( PCIX0_PIM0LAL, CONFIG_SYS_SDRAM_BASE );
        out32r( PCIX0_PIM0LAH, 0 );
        out32r( PCIX0_PIM0SA, ~(gd->ram_size - 1) | 1 );
 
@@ -364,12 +364,12 @@ void pci_target_init(struct pci_controller * hose )
        /*--------------------------------------------------------------------------+
         * Program the board's subsystem id/vendor id
         *--------------------------------------------------------------------------*/
-       out16r( PCIX0_SBSYSVID, CFG_PCI_SUBSYS_VENDORID );
-       out16r( PCIX0_SBSYSID, CFG_PCI_SUBSYS_DEVICEID );
+       out16r( PCIX0_SBSYSVID, CONFIG_SYS_PCI_SUBSYS_VENDORID );
+       out16r( PCIX0_SBSYSID, CONFIG_SYS_PCI_SUBSYS_DEVICEID );
 
        out16r( PCIX0_CMD, in16r(PCIX0_CMD) | PCI_COMMAND_MEMORY );
 }
-#endif /* defined(CONFIG_PCI) && defined(CFG_PCI_TARGET_INIT) */
+#endif /* defined(CONFIG_PCI) && defined(CONFIG_SYS_PCI_TARGET_INIT) */
 
 
 /*************************************************************************
@@ -405,7 +405,7 @@ void board_get_enetaddr (uchar * enet)
        if (0 == macaddr_idx) {
 
                /* Initialize I2C */
-               i2c_init (CFG_I2C_SPEED, CFG_I2C_SLAVE);
+               i2c_init (CONFIG_SYS_I2C_SPEED, CONFIG_SYS_I2C_SLAVE);
 
                /* Read 256 bytes in EEPROM */
                i2c_read (0x50, 0, 1, buff, 0x100);