mmc: tmio: add TMIO_MMC_SDIO_STATUS_QUIRK

Renesas R-Car SDHI should set reserved bits
on CTL_SDIO_STATUS register when writing.
This patch adds new TMIO_MMC_SDIO_STATUS_QUIRK flags
for this purpose

[Kuninori Morimoto: tidyuped for upstreaming
                    enabled this flags for all SH-Mobile/R-Car]

Tested-by: Nguyen Xuan Nui <nx-nui@jinso.co.jp>
Tested-by: Hiep Cao Minh <cm-hiep@jinso.co.jp>
Signed-off-by: Shinobu Uehara <shinobu.uehara.xc@renesas.com>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
(cherry picked from commit 6b98757e53cb0e93b02db4067c14afcb32c90615)
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

mmc: tmio: control multiple block transfer mode

Renesas SDHI has "Multiple Block Transfer Mode" settings
on SD_CMD register which controls CMD12 automatically.

This patch cares it, because
CMD12 is not needed when CMD53 (= SD_IO_RW_EXTENDED)

[Kuninori Morimoto: tidyuped for upstreaming
                    enabled this flags for all SH-Mobile/R-Car]

Tested-by: Nguyen Xuan Nui <nx-nui@jinso.co.jp>
Tested-by: Hiep Cao Minh <cm-hiep@jinso.co.jp>
Signed-off-by: Shinobu Uehara <shinobu.uehara.xc@renesas.com>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
(cherry picked from commit b8d11962c2d83c984d5afd091e5b725ad2fd5607)
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

mmc: tmio: clear error IRQ status

Next card access will be always
error if it didn't clear error status

Tested-by: Nguyen Xuan Nui <nx-nui@jinso.co.jp>
Tested-by: Hiep Cao Minh <cm-hiep@jinso.co.jp>
Signed-off-by: Shinobu Uehara <shinobu.uehara.xc@renesas.com>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
(cherry picked from commit f83bfa751babb521924f6d8c93055215d2eb33cc)
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

mmc: tmio: care about DMA tx/rx addr offset

Basically, SD_BUF0 Tx/Rx addresses are same
in normal TMIO controller,
but, it is different on Renesas R-Car SDHI controller
if it uses DMAC
(Rx address needs to add 0x2000 to Tx address)

This patch adds new .dma_rx_offset and cares it

Tested-by: Nguyen Xuan Nui <nx-nui@jinso.co.jp>
Tested-by: Hiep Cao Minh <cm-hiep@jinso.co.jp>
Acked-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
(cherry picked from commit 384b2cbd56a02efb16358ed7c0c039e4afca5ed0)
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

mmc: tmio: Remove library functions for system PM

These library functions aren't used and nor needed, let's remove them.

Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
(cherry picked from commit 341eb6a4e7beea5730faf55610ef60584bcfffcf)
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

mmc: tmio_mmc: Fixup system PM suspend lock-up

At system PM suspend, the tmio core accessed the internal registers of
the controller without first moving the device into active state. This
caused a lock-up in system PM suspend phase.

The reason for the register access were masking of IRQs. Since that is
managed via the runtime PM suspend path, let's just re-use that path
for system PM suspend.

In other words force the device into runtime PM suspend state at system
PM suspend and restore it to active state at system PM resume.

Reported-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
(cherry picked from commit 70a15e1a3c58ee841415c84170b80a3859027686)
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

mmc: sdhi: Fixup system PM suspend lock-up

At system PM suspend, the tmio core accessed the internal registers of
the controller without first moving the device into active state. This
caused a lock-up in system PM suspend phase.

The reason for the register access were masking of IRQs. Since that is
managed via the runtime PM suspend path, let's just re-use that path
for system PM suspend.

In other words force the device into runtime PM suspend state at system
PM suspend and restore it to active state at system PM resume.

Reported-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
(cherry picked from commit 753a688c9f28ad3198611bbbd39f3b226c35ab98)
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

mmc: tmio_mmc: Enable runtime PM support

To take advantage of the clock gating support, use the runtime PM
callbacks provided by the tmio core.

Additionally, we make use of the SET_PM_RUNTIME_PM_OPS, which is a
preparation needed to simplify system PM.

Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
(cherry picked from commit 78f76df60926f7853df9ee2b707ea9254129775c)
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

mmc: sdhi: Make runtime PM callbacks available for CONFIG_PM

To be able to simplify system PM, let's re-use the runtime PM callbacks
by converting to the SET_PM_RUNTIME_PM_OPS macro.

Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
(cherry picked from commit f74f1e38206df93b9e11d5a8b84743e61c0768a6)
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

mmc: tmio: Make runtime PM callbacks available for CONFIG_PM

To give the option for tmio hosts to use the runtime PM callbacks for
CONFIG_PM_SLEEP as well as CONFIG_PM_RUNTIME, move them to CONFIG_PM.

Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
(cherry picked from commit 9ade7dbf20e8fc73d9784b772e320239de2acf08)
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

mmc: tmio: Mask all IRQs when inactive

To make sure we don't receive any spurious IRQs while we are inactive,
mask the IRQs from within the ->runtime_suspend() callback.

Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
(cherry picked from commit 20e955c3c746f434a2f97ab08ac6bd71f63c6afa)
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

mmc: tmio: Handle clock gating from runtime PM functions

Add clock gating control as a part of the tmio library functions for
runtime PM.

Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
(cherry picked from commit ae12d25053fa20d67b16e568917b956006d5dc01)
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

mmc: tmio: Restructure ->set_ios() and adapt ->probe() to it

An internal power state machine were beeing used to keep ->probe() and
->set_ios() in sync. Especially for handling specific scenarios while
using CONFIG_MMC_CLKGATE. Moreover dependency to CONFIG_MMC_CLKGATE
existed to handle runtime PM properly, which we moves away from here.

By removing the state machine and instead make ->set_ios() rely on the
information provided through the function's in-parameters, the code
becomes significantly simplier.

Additonally as a part of this rework we prepares for making the runtime
PM callbacks responsible of clock gating.

Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
(cherry picked from commit 3b292bb0e99018c448e0f5a26c29c68113a1b7bf)
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

mmc: tmio: Extract bus_width modifications to a separate function

Move code for bus_width modification, out of the ->set_ios() callback
and into a separate function, to simplify code.

Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
(cherry picked from commit 9ae4ed7d30f433873351d5ba14ae000d10e10430)
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

mmc: tmio: Keep host active while serving requests

Use runtime PM to keep the host active during I/O operations and other
requests which requires the tmio hardware to be powered.

Additionally make use of the runtime PM autosuspend feature with a
default timeout of 50 ms.

Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
(cherry picked from commit 0369483efc1719f47249fa94329aa94155edf69d)
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

mmc: tmio: Keep host active while SDIO IRQ is enabled

The host must be kept active to be able to serve SDIO IRQs, thus let's
prevent it from going inactive while SDIO IRQ is enabled.

Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
(cherry picked from commit 7501c4315faf46b088ed4de4d8695a91d7d63869)
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Merge tag 'backport/v3.14.24-ltsi-rc1/pm-runtime-20141105' into backport/v3.14.24-ltsi-rc1/mach-shmobile.base

PM: Add pm_runtime_suspend|resume_force functions

This patch provides two new runtime PM helper functions which intend to
be used from system suspend/resume callbacks, to make sure devices are
put into low power state during system suspend and brought back to full
power at system resume.

The prerequisite is to have all levels of a device's runtime PM
callbacks to be defined through the SET_PM_RUNTIME_PM_OPS macro, which
means these are available for CONFIG_PM.

By using the new runtime PM helper functions especially the two
scenarios below will be addressed.

1) The PM core prevents .runtime_suspend callbacks from being invoked
during system suspend. That means even for a runtime PM centric
subsystem and driver, the device needs to be put into low power state
from a system suspend callback. Otherwise it may very well be left in
full power state (runtime resumed) while the system is suspended. By
using the new helper functions, we make sure to walk the hierarchy of
a device's power domain, subsystem and driver.

2) Subsystems and drivers need to cope with all the combinations of
CONFIG_PM_SLEEP and CONFIG_PM_RUNTIME. The two new helper functions
smothly addresses this.

Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
(cherry picked from commit 37f204164dfb0186a0caf20bc3e3120080bcd788)
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

PM / runtime: Fetch runtime PM callbacks using a macro

While fetching the proper runtime PM callback, we walk the hierarchy of
device's power domains, subsystems and drivers.

This is common for rpm_suspend(), rpm_idle() and rpm_resume(). Let's
clean up the code by using a macro that handles this.

Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
(cherry picked from commit 5f59df79837bb809f3945613aba5519cd9755a53)
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

mmc: Add .multi_io_quirk callback for multi I/O HW bug

Historically, we have been using MMC_CAP* to handle host HW issues and
currently the block layer uses MMC_CAP2_NO_MULTI_READ flag for a multi
I/O HW bug workaround.

There are a few tweaks needed to make MMC_CAP2_NO_MULTI_READ suite all
situations. Therefore let's add an optional host ops callback to enable
host drivers to return the number of blocks it allows per request.

In a future patch and when host drivers have converted to the new
callback, MMC_CAP2_NO_MULTI_READ shall be removed.

Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
(cherry picked from commit 2e47e84245adcb1b3872210678b6146f674fb3ff)
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

watchdog: iTCO_wdt: Fix the parent device

The watchdog's parent is iTCO_wdt (the platform device) not lpc_ich
(the PCI device.) Setting the parent right makes it much easier for
the user to figure out which driver/module is handling the watchdog
device node.

Signed-off-by: Jean Delvare <jdelvare@suse.de>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
(cherry picked from commit c90789baa8cec363093c5ec292c989b6f22d8f32)

Signed-off-by: Chang Rebecca Swee Fun <rebecca.swee.fun.chang@intel.com>

watchdog: fix checkpatch warnings and error

Fix the following checkpatch warnings and error:
  WARNING: quoted string split across lines
  WARNING: braces {} are not necessary for single statement blocks
  WARNING: __initdata should be placed after ibmasr_id_table[]
  WARNING: please, no space before tabs
  ERROR: do not initialise statics to 0 or NULL

Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
(cherry picked from commit 5f5e19093b2fa592720810154f15ffe51aa9277f)

Signed-off-by: Chang Rebecca Swee Fun <rebecca.swee.fun.chang@intel.com>

watchdog: iTCO_wdt: Add support for v3 silicon

Some new Atom's, eg Avoton and Bay Trail, have slightly different iTCO
functionality:
- The watchdog timer ticks at 1 second instead of .6 seconds

- Some 8 and 16-bit registers were combined into 32-bit registers

- Some registers were removed (DAT_IN, DAT_OUT, MESSAGE)

- The BOOT_STS field in TCO_STS was removed

- The NO_REBOOT bit is in the PMC area instead of GCS

Update the driver to support the above changes and bump the version to
1.11.

Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Tested-by: Rajat Jain <rajatjain@juniper.net>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
(cherry picked from commit 24b3a1670b47e75be633ae0b5c07945c446f9d29)

Signed-off-by: Chang Rebecca Swee Fun <rebecca.swee.fun.chang@intel.com>

mfd: lpc_ich: Add Device IDs for Intel 9 Series PCH

This patch adds the LPC Device IDs for the Intel 9 Series PCH.

Signed-off-by: James Ralston <james.d.ralston@intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
(cherry picked from commit fea31042ff613145c7784e2ce454bf3c151b97ba)

Signed-off-by: Chang Rebecca Swee Fun <rebecca.swee.fun.chang@intel.com>

mfd: lpc_ich: Add PCI ID for Intel Braswell

This is the same as used in Baytrail so add the new PCI ID to the driver's
list of supported IDs.

Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
(cherry picked from commit ff0c9da013d2c9f1ec232926a54e536ab48c6678)

Signed-off-by: Chang Rebecca Swee Fun <rebecca.swee.fun.chang@intel.com>

mfd: lpc_ich: Enable GPIO for Panther Point

Panther Point PCH GPIO configuration is similar to V5 PCHs.

Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
(cherry picked from commit 62cf2cdb99c7e870ab857bdd617e728790f8c43c)

Signed-off-by: Chang Rebecca Swee Fun <rebecca.swee.fun.chang@intel.com>

mfd: lpc_ich: Add support for Intel Bay Trail SoC

This patch adds the LPC Controller Device IDs for Watchdog and GPIO for
the Intel Bay Trail Atom SoC.

Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
(cherry picked from commit 6111ec70357022ccd037399c13f69900431850b4)

Signed-off-by: Chang Rebecca Swee Fun <rebecca.swee.fun.chang@intel.com>

mfd: lpc_ich: Add support for NM10 GPIO

The NM10's GPIO is compatible with ICH v7 GPIO.

Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Tested-by: Dan Weinlader <danw@vs-networks.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
(cherry picked from commit 117bbfe25cfc2e968be1f7976ac460a5cd3d734e)

Signed-off-by: Chang Rebecca Swee Fun <rebecca.swee.fun.chang@intel.com>

mfd: lpc_ich: Change Avoton to iTCO v3

The register layout of the Avoton is compatible with the iTCO v3
register layout.

Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Tested-by: Rajat Jain <rajatjain@juniper.net>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
(cherry picked from commit c48cf59878685cc06b71bb2a3ca17b61103c8de7)

Signed-off-by: Chang Rebecca Swee Fun <rebecca.swee.fun.chang@intel.com>

mfd: lpc_ich: Add support for iTCO v3

Some newer Atom CPUs, eg Avoton and Bay Trail, use slightly different
register layouts for the iTCO than the current v1 and v2 iTCO.
Differences from previous iTCO versions include:
- The ACPI space is enabled in the "ACPI base address" register instead
  of the "ACPI control register"

- The "no reboot" functionality is set in the "Power Management
  Configuration" register instead of the "General Control and Status"
  (GCS) register or PCI configuration space.

- The "ACPI Control Register" is not present on v3.  The "Power
  Management Configuration Base Address" register resides at the same
  address is Avoton/Bay Trail.

To differentiate these newer chipsets create a new v3 iTCO version and
update the MFD driver to support them.

Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Tested-by: Rajat Jain <rajatjain@juniper.net>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
(cherry picked from commit eb71d4dec4a5e010e34b9d7afdb5af41884c388e)

Signed-off-by: Chang Rebecca Swee Fun <rebecca.swee.fun.chang@intel.com>

mfd: lpc_ich: Remove lpc_ich_cfg struct use

Future chipsets will use different register layouts that don't map
cleanly to the lpc_ich_cfg fields.  Remove the lpc_ich_cfg struct and
add explicit fields to the higher level lpc_ich_priv structure.

This change should have no functional impact.

Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Tested-by: Rajat Jain <rajatjain@juniper.net>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
(cherry picked from commit 429b941abd503c8936e116c819362323aafdbd50)

Signed-off-by: Chang Rebecca Swee Fun <rebecca.swee.fun.chang@intel.com>

mfd: lpc_ich: Only configure watchdog or GPIO when present

Some chipsets don't currently have GPIO support enabled.  For these
chipsets don't go through the process of initializing the GPIO region.

Make the same change for the watchdog initialization for chipsets which
may not enable the WDT in the future.

Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Tested-by: Rajat Jain <rajatjain@juniper.net>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
(cherry picked from commit f0776b8ce03ceb638c51b62f324844c71c446600)

Signed-off-by: Chang Rebecca Swee Fun <rebecca.swee.fun.chang@intel.com>

mfd: lpc_ich: Fix ACPI enable bitmask

The original bitmask of 0x10 was incorrect and would result in a write
to a reserved read-only bit instead of enabling the ACPI I/O
region.  Update it to the proper value of 0x80.

Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Tested-by: Rajat Jain <rajatjain@juniper.net>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
(cherry picked from commit f5dccb15877b82a40950c6f752d5345c86189fc9)

Signed-off-by: Chang Rebecca Swee Fun <rebecca.swee.fun.chang@intel.com>

mfd: lpc_ich: Add support for Intel Avoton GPIOs

Signed-off-by: Vincent Donnefort <vdonnefort@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
(cherry picked from commit facd9939403cb5769190054a600474399e776e3a)

Signed-off-by: Chang Rebecca Swee Fun <rebecca.swee.fun.chang@intel.com>

mfd: lpc_ich: Convert ICH GPIOs IDs to enum

All those IDs are arbitrary and so can be encapsulated into an enumeration.

Signed-off-by: Vincent Donnefort <vdonnefort@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
(cherry picked from commit 6cec365e3eba3dd8c864056d8d3fd9e73ab8dd7a)

Signed-off-by: Chang Rebecca Swee Fun <rebecca.swee.fun.chang@intel.com>

mfd: Delete non-required instances of include <linux/init.h>

None of these files are actually using any __init type directives
and hence don't need to include <linux/init.h>.  Most are just a
left over from __devinit and __cpuinit removal, or simply due to
code getting copied from one driver to the next.

Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
(cherry picked from commit 3c699105d0376c14940ce7cf561754a94cdff8dd)

Signed-off-by: Chang Rebecca Swee Fun <rebecca.swee.fun.chang@intel.com>

i2c: i801: Add PCI ID for Intel Braswell

The SMBus host controller is the same as used in Baytrail so add the new
PCI ID to the driver's list of supported IDs.

Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
(cherry picked from commit 39e8e30ee544a62c148033d64a979028b958ca05)

Signed-off-by: Chang Rebecca Swee Fun <rebecca.swee.fun.chang@intel.com>

i2c: i801: Add device ID for Intel Wildcat Point PCH

Signed-off-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
(cherry picked from commit b299de839157852c563b9f133c8b7e630545a9c3)

Signed-off-by: Chang Rebecca Swee Fun <rebecca.swee.fun.chang@intel.com>

i2c: i801: Fix the alignment of the device table

A long name broke the alignment, shift the columns a bit to fix it and
make the table look nice again. While we're here, switch to the
standard comment style to make checkpatch happy, and use tabs instead
of spaces for column alignment.

Signed-off-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
(cherry picked from commit ce3161106ab57afbfbe1c33d95bf4a569405983a)

Signed-off-by: Chang Rebecca Swee Fun <rebecca.swee.fun.chang@intel.com>

i2c: remove DEFINE_PCI_DEVICE_TABLE macro

Don't use DEFINE_PCI_DEVICE_TABLE macro, because this macro
is not preferred.

Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
(cherry picked from commit 392debf11656dedd79da44416747d5b2b1747f5e)

Signed-off-by: Chang Rebecca Swee Fun <rebecca.swee.fun.chang@intel.com>

pwm: lpss: use c99 initializers in structures

Use c99 initializers for structures.

A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)

// <smpl>
@decl@
identifier i1,fld;
type T;
field list[n] fs;
@@

struct i1 {
 fs
 T fld;
 ...};

@bad@
identifier decl.i1,i2;
expression e;
initializer list[decl.n] is;
@@

struct i1 i2 = { is,
+ .fld = e
- e
 ,...};
// </smpl>

Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
[thierry.reding: rebased and applied same fix for Braswell]
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
(cherry picked from commit b2b7adeb21745266326d453b95e5d0b1b9cb1d4e)

Signed-off-by: Chang Rebecca Swee Fun <rebecca.swee.fun.chang@intel.com>

pwm: lpss: Fix build failure on PowerPC

An x86 build seems to pull in the linux/io.h include indirectly. On
PowerPC that doesn't happen and the build breaks due to the readl() and
writel() functions not being declared. Fix this by explicitly including
linux/io.h.

Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
(cherry picked from commit e0c86a3b63e948e51a47d17382c7cd8711d19750)

Signed-off-by: Chang Rebecca Swee Fun <rebecca.swee.fun.chang@intel.com>

pwm: lpss: Properly split driver to parts

The driver consists of core, PCI, and platform parts. It would be better
to split them into separate files.

The platform driver is now called pwm-lpss-platform. Thus, previously
set CONFIG_PWM_LPSS=m is not enough to build it. But we are on the safe
side since it seems no one from outside Intel is using it for now.

While here, move to use macros module_pci_driver() and
module_platform_driver().

Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Alan Cox <alan@linux.intel.com>
[thierry.reding: change select to depends on PWM_LPSS, cleanup]
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
(cherry picked from commit c558e39e14c2372394f49e07fbe94e9708b615cb)

Signed-off-by: Chang Rebecca Swee Fun <rebecca.swee.fun.chang@intel.com>

pwm: lpss: Add ACPI and PCI IDs for Intel Braswell

This is pretty much the same as Baytrail PWM. Only difference is that the
input clock runs on different frequency.

Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
(cherry picked from commit 373c57829a3f9da1405b1fbd3d17e50f8e1f476e)

Signed-off-by: Chang Rebecca Swee Fun <rebecca.swee.fun.chang@intel.com>

pwm: lpss: remove dependency on clk framework

Unlike other Intel LPSS devices, the PWM does not have the
clock dividers or the gate. All we get from the clock is the
rate. Since PCI case uses the driver data to get the rate,
we can drop the clk and use the same data also in case of
ACPI. The frequency is the same.

Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Chew, Chiau Ee <chiau.ee.chew@intel.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
(cherry picked from commit 65accd87381ed96bf8893124b149bae08edd2740)

Signed-off-by: Chang Rebecca Swee Fun <rebecca.swee.fun.chang@intel.com>

pwm: lpss: Fix const qualifier and sparse warnings

Fixes the following warnings reported by the 0-DAY kernel build testing
backend:

   drivers/pwm/pwm-lpss.c: In function 'pwm_lpss_probe_pci':
>> drivers/pwm/pwm-lpss.c:192:2: warning: passing argument 3 of 'pwm_lpss_probe' discards 'const' qualifier from pointer target type [enabled by default]
     lpwm = pwm_lpss_probe(&pdev->dev, &pdev->resource[0], info);
     ^
   drivers/pwm/pwm-lpss.c:130:30: note: expected 'struct pwm_lpss_boardinfo *' but argument is of type 'const struct pwm_lpss_boardinfo *'
    static struct pwm_lpss_chip *pwm_lpss_probe(struct device *dev,
                                 ^
>> drivers/pwm/pwm-lpss.c:143:28: sparse: incorrect type in return expression (different address spaces)
   drivers/pwm/pwm-lpss.c:143:28:    expected struct pwm_lpss_chip *
   drivers/pwm/pwm-lpss.c:143:28:    got void [noderef] <asn:2>*regs
>> drivers/pwm/pwm-lpss.c:192:63: sparse: incorrect type in argument 3 (different modifiers)
   drivers/pwm/pwm-lpss.c:192:63:    expected struct pwm_lpss_boardinfo *info
   drivers/pwm/pwm-lpss.c:192:63:    got struct pwm_lpss_boardinfo const *[assigned] info
   drivers/pwm/pwm-lpss.c: In function 'pwm_lpss_probe_pci':
   drivers/pwm/pwm-lpss.c:192:2: warning: passing argument 3 of 'pwm_lpss_probe' discards 'const' qualifier from pointer target type [enabled by default]
     lpwm = pwm_lpss_probe(&pdev->dev, &pdev->resource[0], info);
     ^
   drivers/pwm/pwm-lpss.c:130:30: note: expected 'struct pwm_lpss_boardinfo *' but argument is of type 'const struct pwm_lpss_boardinfo *'
    static struct pwm_lpss_chip *pwm_lpss_probe(struct device *dev,
                                 ^

Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
(cherry picked from commit 89c0339e0aa097384b3efed894b23820814c21d3)

Signed-off-by: Chang Rebecca Swee Fun <rebecca.swee.fun.chang@intel.com>

pwm: lpss: Add support for PCI devices

Not all systems enumerate the PWM devices via ACPI. They can also be
exposed via the PCI interface.

Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Chew, Chiau Ee <chiau.ee.chew@intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
(cherry picked from commit 093e00bb3f82f3c67e2d1682e316fc012bcd0d92)

Signed-off-by: Chang Rebecca Swee Fun <rebecca.swee.fun.chang@intel.com>

pwm: add support for Intel Low Power Subsystem PWM

Add support for Intel Low Power I/O subsystem PWM controllers found on
Intel BayTrail SoC.

Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Chew, Kean Ho <kean.ho.chew@intel.com>
Signed-off-by: Chang, Rebecca Swee Fun <rebecca.swee.fun.chang@intel.com>
Signed-off-by: Chew, Chiau Ee <chiau.ee.chew@intel.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
(cherry picked from commit d16a5aa9e821633a3095d7a88cd1d2cd108bf966)

Signed-off-by: Chang Rebecca Swee Fun <rebecca.swee.fun.chang@intel.com>

of/fdt: update of_get_flat_dt_prop in prep for libfdt

Make of_get_flat_dt_prop arguments compatible with libfdt fdt_getprop
call in preparation to convert FDT code to use libfdt. Make the return
value const and the property length ptr type an int.

Signed-off-by: Rob Herring <robh@kernel.org>
Tested-by: Michal Simek <michal.simek@xilinx.com>
Tested-by: Grant Likely <grant.likely@linaro.org>
Tested-by: Stephen Chivers <schivers@csc.com>
(cherry picked from commit 9d0c4dfedd96ee54fc075b16d02f82499c8cc3a6)
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Conflicts:
arch/arm/plat-samsung/s5p-dev-mfc.c
arch/powerpc/platforms/powernv/opal.c
drivers/of/fdt.c
drivers/of/of_reserved_mem.c

clk: add clock-indices support

Add a property called clock-indices to allow clock-output-names
to be used where the index used to lookup a clock is not a 1:1
mapping to the array position in the clock-output-names

Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
(cherry picked from commit 7a0fc1a3df82d29e00b4c9f88a6b37450d6711f1)
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

i2c: rcar: fix RCAR_IRQ_ACK_{RECV|SEND}

Bits 8-31 of all registers reflect the value of bits 0-7 on reads and should be
0 on writes, according to the manuals. RCAR_IRQ_ACK_{RECV|SEND} macros have all
1's in bits 8-31, thus going against the manuals, so fix them.

Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Cc: stable@vger.kernel.org
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
(cherry picked from commit 938916fbb8e8cb67eacb784f4eda17e2950c16c5)
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

usb: renesas_usbhs: fix the usb_pkt_pop()

This patch fixes the usb_pkt_pop(). If a gadget driver calls
usb_ep_dequeue(), this driver will call the usb_pkt_pop().
So, the usb_pkt_pop() should cancel the transaction.

Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
(cherry picked from commit 2743e7f90dc08282d027dbc2f6486f5cb85aa493)
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

usb: renesas_usbhs: fix the condition of is_done in usbhsf_dma_push_done

This patch fixes the condition of is_done in usbhsf_dma_push_done().
This function will be called after a transmission finished by DMAC.
So, the function should check if the transmission packet is short packet
or not. Also the function should call try_run to send the zero packet
by the pio handler if the "*is_done" is not set. Otherwize, the
transaction will not finish if a gadget driver sets the "zero" flag
in a transmission.

Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
(cherry picked from commit c0ed8b23b257a84d103764cdbd490ee5e2749da3)
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

usb: renesas_usbhs: protect mod->irq_{bemp,brdy}sts by spin lock

This patch protects the mod->irq_bempsts and mod->irq_brdysts by
spin lock in the usbhs_status_get_each_irq() because other functions
will write them during spin lock. Otherwise, the driver will clears
the BRDYSTS and/or BEMPSTS wrongly, and then, the transaction will not
finish.
Also since the driver should use the INTSTS0 and BRDYSTS and BEMPSTS
as the same timing, the patch protects them.

Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
(cherry picked from commit c4d8199ba1a7aa390b06db23f4532e2c1875aefb)
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

usb: renesas_usbhs: fix the behavior of some usbhs_pkt_handle

Some gadget drivers will call usb_ep_queue() more than once before
the first queue doesn't finish. However, this driver didn't handle
it correctly. So, this patch fixes the behavior of some
usbhs_pkt_handle using the "running" flag. Otherwise, the oops below
happens if we use g_ncm driver and when the "iperf -u -c host -b 200M"
is running.

Unable to handle kernel NULL pointer dereference at virtual address 00000000
pgd = c0004000
[00000000] *pgd=00000000
Internal error: Oops: 80000007 [#1] SMP ARM
Modules linked in: usb_f_ncm g_ncm libcomposite u_ether
CPU: 0 PID: 0 Comm: swapper/0 Tainted: G        W      3.17.0-rc1-00008-g8b2be8a-dirty #20
task: c051c7e0 ti: c0512000 task.ti: c0512000
PC is at 0x0
LR is at usbhsf_pkt_handler+0xa8/0x114
pc : [<00000000>]    lr : [<c0278fb4>]    psr: 60000193
sp : c0513ce8  ip : c0513c58  fp : c0513d24
r10: 00000001  r9 : 00000193  r8 : eebec4a0
r7 : eebec410  r6 : eebe0c6c  r5 : 00000000  r4 : ee4a2774
r3 : 00000000  r2 : ee251e00  r1 : c0513cf4  r0 : ee4a2774

Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
(cherry picked from commit 8355b2b3082d302091506703d2e4e239f7deed7f)
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

net: sh_eth: fix driver dependencies

Renesas SuperH Ethernet support should be available only on
Renesas ARM SoCs and SuperH architecture.

Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Simon Horman <horms@verge.net.au>
Cc: Magnus Damm <magnus.damm@gmail.com>
Acked-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
(cherry picked from commit f6ec9c335b502d8011971d07508589d212cb3c93)
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

ASoC: rcar: Use && instead of & for boolean expressions

Sparse spits out the following warning:
sound/soc/sh/rcar/gen.c:250:21: warning: dubious: x & !y

It does this because sometimes mixing boolean and bit-wise logic has not the
intended result. In this case we are fine, but replacing the bit-wise '&' with
the boolean '&&' silences the sparse warning. The generated code for both cases
is the same.

Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
(cherry picked from commit c8e6e960733f4a5835265c15429fced4d2f1595e)
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Revert "i2c: rcar: remove spinlock"

This reverts commit 150b8be3cda54412ad7b54f5392b513b25c0aaa7.

The I2C core's per-adapter locks can't protect from IRQs, so the driver still
needs a spinlock to protect the register accesses.

Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Cc: stable@vger.kernel.org # 3.16+
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
(cherry picked from commit 91bfe2989af02e709ca01ccf518c4fbda3efc70f)
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

i2c: rcar: fix MNR interrupt handling

Sometimes the MNR and MST interrupts happen simultaneously  (stop  automatically
follows NACK, according to the manuals) and in such case the ID_NACK flag  isn't
set since the MST interrupt handling precedes MNR and all interrupts are cleared
and disabled then, so that MNR interrupt is never noticed -- this causes NACK'ed
transfers to be falsely reported as successful. Exchanging MNR and  MST handlers
fixes this issue, however the MNR bit  somehow  gets set again even after  being
explicitly cleared, so I decided to completely suppress handling of all disabled
interrupts (which is a good thing anyway)...

Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Cc: stable@vger.kernel.org
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
(cherry picked from commit dd318b0df27c582ac0d72a346fd6e693700be23c)
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

ASoC: ak4642: Make of_device_id array const

Make of_device_id array const, because all OF functions handle it as const

Signed-off-by: Kiran Padwal <kiran.padwal21@gmail.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
(cherry picked from commit 27204ca8b981160c3b65cdc226c9070f76cbbd36)
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

usb: host: xhci-plat: add support for the R-Car H2 and M2 xHCI controllers

The R-Car H2 and M2 SoCs come with an xHCI controller that requires
some specific initializations related to the firmware downloading and
some specific registers. This patch adds the support for this special
configuration as an xHCI quirk executed during probe and start.

Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Cc: "mathias.nyman@intel.com" <mathias.nyman@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
(cherry picked from commit 4ac8918f3a737c21d81e250e4194c12ea2b7eb04)
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

usb: host: xhci-plat: use devm_functions

This patch introduces the use of managed interface devm_ioremap_resource
for ioremap_nocache and request_mem_region and removes the corresponding
free functions in the probe and remove functions.

Signed-off-by: Himangi Saraogi <himangi774@gmail.com>
Acked-by: Julia Lawall <julia.lawall@lip6.fr>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Cc: Mathias Nyman <mathias.nyman@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
(cherry picked from commit fd666348c51f6ab66410c98a149e0418b9a258f0)
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

xhci: Platform: Set xhci lpm support quirk based on platform data

If an xhci platform supports USB3 LPM capability then enable
XHCI_LPM_SUPPORT quirk flag.

Signed-off-by: Pratyush Anand <pratyush.anand@st.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
(cherry picked from commit 20f6fdd01c2c0de9cc1109083222edded24c5350)
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

xhci: Platform: Add (en/dis)able_usb3_lpm_timeout

To use auto U0-U1/U2 transition by xhci platform device add
(en/dis)able_usb3_lpm_timeout function to the xhci_plat_xhci_driver struct.

Signed-off-by: Pratyush Anand <pratyush.anand@st.com>
Tested-by: Aymen Bouattay <aymen.bouattay@st.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
(cherry picked from commit 94ef3d50426240a5402688e8d43a079df5ae21be)
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

ARM: shmobile: koelsch: Remove non-existent i2c6 pinmux

On r8a7791, i2c6 (aka iic3) doesn't need pinmux, but the koelsch dts
refers to non-existent pinmux configuration data:

pinmux core: sh-pfc does not support function i2c6
sh-pfc e6060000.pfc: invalid function i2c6 in map table

Remove it to fix this.

Fixes: commit 1d41f36a68c0f4e9b01d563ce33bab5201858b54 ("ARM: shmobile:
       koelsch dts: Add VDD MPU regulator for DVFS")

Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Olof Johansson <olof@lixom.net>
(cherry picked from commit 12266db732ff3845eaa9ba9354c4938249787aaf)
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

ARM: shmobile: r8a7791: add missing 0x0100 for SDCKCR

4bfb358b1d6cdeff8c6a13677f01ed78e9696b98
(ARM: shmobile: Add r8a7791 legacy SDHI clocks)
added r8a7791 SDHI clock support.

But, it is missing
"0x0100: x 1/8" division ratio.
This patch fixes hidden bug.
It is based on R-Car H2 v0.7, R-Car M2 v0.9.

Reported-by: Yusuke Goda <yusuke.goda.sx@renesas.com>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
(cherry picked from commit 58b80ad6472c0fa12926dfa1f9103d3a326bdf18)
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

ARM: shmobile: r8a7790: add missing 0x0100 for SDCKCR

9f13ee6f83c52065112d3e396e42e3780911ef53
(ARM: shmobile: r8a7790: add div4 clocks)
added r8a7790 DIV4 clock support.

But, it is missing
"0x0100: x 1/8" division ratio.
This patch fixes hidden bug.
It is based on R-Car H2 v0.7, R-Car M2 v0.9.

Reported-by: Yusuke Goda <yusuke.goda.sx@renesas.com>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
(cherry picked from commit 4fb12fe9c34928c1d2bed817e144aec3f44540e9)
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

ARM: shmobile: defconfig: Remove MACH_GENMAI

The CONFIG_MACH_GENMAI is scheduled for removal so remove it from
shmobile_defconfig.

Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
[horms+renesas@verge.net.au: revised changelog for updated commit order]
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
(cherry picked from commit 92db2b7af591d3c3212183a34856b4cb190b6999)
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

ARM: shmobile: sh73a0: Remove spurious 0x from SCIFB clock name

A stray '0x' crept into a0f7e7496d56ac2d ("ARM: shmobile: sh73a0: add CMT1
clock support for DT"). This  patch removes it.

This change should not have any run-time affect at this time as
the clock in question is used by a SCIF device that is not enabled by
default.

Reported-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
(cherry picked from commit 2c3758b01aa6f11382d2b018614b5d48ecf30350)
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

ARM: shmobile: genmai: remove defconfig

The genmai board code is scheduled for removal and once
that occurs the defconfig will be of no use. Remove it.

Acked-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
(cherry picked from commit 3ed27bd90d6d0c8b4d686a2468b6d50cc1ef74e4)
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

ARM: shmobile: sh73a0: add CMT1 clock support for DT

This will be used when initialising CMT1 device using DT
until common clock framework support is added.

Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
(cherry picked from commit a0f7e7496d56ac2da7c684e2035815318c17973a)
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

ARM: shmobile: r8a7740: add CMT1 clock support for DT

This will be used when initialising CMT1 device using DT
until common clock framework support is added.

Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
(cherry picked from commit 2e11179da78a56c2a44fc3fe097f2af8dc18f9d6)
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

ARM: shmobile: r8a73a4: add CMT1 clock support for DT

This will be used when initialising CMT1 device using DT
until common clock framework support is added.

Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
(cherry picked from commit aad64dc31954dbbb84cd8fcfaf1bc028f3bc2616)
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

ARM: shmobile: r8a7740: add TMU clock support for DT

This will be used when initialising TMU devices using DT
until common clock framework support is added.

Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
(cherry picked from commit ef9cb75ca70c8d31b2493d1fd6cbf8b3dd1dec95)
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

ARM: shmobile: r8a7778: add TMU clock support for DT

This will be used when initialising TMU devices using DT
until common clock framework support is added.

Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
(cherry picked from commit 0985f38d1379291c8701572e761c809f0d5f6476)
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

ARM: shmobile: kzm9g-reference: Initialise SCIF device using DT

Initialise SCIF device using DT when booting armadillo800eva
using DT reference.

Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
(cherry picked from commit 700ce7c2bb2a4963472d95eba1436d6b0945918e)
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

ARM: shmobile: sh73a0: Add SCIF nodes

This describes all of the SCIF hardware of the sh73a0.
Each node is disabled and may be enabled as necessary
by board DTS files.

Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
(cherry picked from commit 2131421b85c9f25082a2b0ec371c7ad0c47cc943)
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

ARM: shmobile: armadillo800eva-reference: Initialise SCIF device using DT

Initialise SCIF device using DT when booting armadillo800eva
using DT reference.

Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
(cherry picked from commit c4fac6f2f92331fa5788811357f8b8c3352e5ad8)
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

ARM: shmobile: r8a7740: Add SCIF nodes

This describes all of the SCIF hardware of the r8a7740.
Each node is disabled and may be enabled as necessary
by board DTS files.

Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
(cherry picked from commit fa12355b24a430729f34c349473b9c0a3d125679)
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

ARM: shmobile: ape6evm-reference: Initialise SCIF device using DT

Initialise SCIF device using DT when booting ape6evm
using DT reference.

Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
(cherry picked from commit 27bc82353a3f214a383d7f3b1ccaefdb70d6c94f)
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

ARM: shmobile: r8a73a4: Add SCIF nodes

This describes all of the SCIF hardware of the r8a73a4.
Each node is disabled and may be enabled as necessary
by board DTS files.

Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
(cherry picked from commit 94f1a03db6988c64601dc84eaf6c8ef1b956d9e7)
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

ARM: shmobile: bockw-reference: Initialise SCIF device using DT

Initialise SCIF device using DT when booting bockw
using DT reference.

Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
(cherry picked from commit 5be97ca4a4f6e11c4a839ec3c08dea25589dfeb4)
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

ARM: shmobile: r8a7778: Add SCIF nodes

This describes all of the SCIF hardware of the r8a7778.
Each node is disabled and may be enabled as necessary
by board DTS files.

Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
(cherry picked from commit 9930dc8ee1f59271a54ed4b4922c9c944625a8d6)
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

ARM: shmobile: sh73a0: add SCI clock support for DT

This will be used when initialising SCI devices using DT
until common clock framework support is added.

Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
(cherry picked from commit ff4ce48e1f163d945c037c1c90ce12950961d91d)
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

ARM: shmobile: r8a7740: correct SCI clock support for DT

When initialising SCI devices their names will be .serial
not .sci.

This will be used when initialising SCI devices using DT
until common clock framework support is added.

Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
(cherry picked from commit d1ec90f2875471df2c954f7cbd45b2389ff86aa2)
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

ARM: shmobile: r8a73a4: add SCI clock support for DT

This will be used when initialising SCI devices using DT
until common clock framework support is added.

Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
(cherry picked from commit 9947efaac0545fd833b0ff5147578aba79d297bc)
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

ARM: shmobile: r8a7778: add SCI clock support for DT

This will be used when initialising SCI devices using DT
until common clock framework support is added.

Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
(cherry picked from commit 7a0c99478dca80f862912be02bf8ec240a9098d1)
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

ARM: shmobile: r8a7790: lager: use iic cores instead of i2c

On Lager board, i2c and iic cores can be interchanged since they can be
muxed to the same wires. Commit e489c2a9bc82713167d9f721ca764f4b0d37e543
("ARM: shmobile: lager: enable i2c devices") activated the i2c cores,
yet the iic cores should be default since they have the more interesting
features for generic use cases, i.e. SMBUS_QUICK and DMA (yet to be
supported).

Reported-by: Khiem Nguyen <khiem.nguyen.xt@renesas.com>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
(cherry picked from commit cb9a2b12e0cb524022c9a81d8ed29f2453ec240d)
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

ARM: shmobile: Lager: Correct I2C bus for VDD MPU regulator

I2C bus for VDD MPU regulator is IIC3, not I2C3.

Signed-off-by: Khiem Nguyen <khiem.nguyen.xt@renesas.com>
Reviewed-by: Wolfram Sang <wsa@sang-engineering.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
(cherry picked from commit 5179ffd099446e65a1e094b9cb17cc7edab45583)
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

ARM: shmobile: Remove opps table check for cpufreq

This patch is based on feedback from Viresh Kumar.
Since cpufreq-cpu0 driver has already check opp table, there is no
need to same check in mach-shmobile.

Signed-off-by: Gaku Inami <gaku.inami.xw@bp.renesas.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
(cherry picked from commit e423d12cbcb9576785e891617888f627f1f57bf4)
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

ARM: shmobile: Enable R-Car Gen 2 PCIe in shmobile_defconfig

The R-Car Gen 2 PCIe driver provides PCIe host support for
Renesas R-Car Gen2 platforms. To increase hardware support enable
the driver in the shmobile_defconfig multiplatform configuration.

Cc: Phil Edworthy <phil.edworthy@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
(cherry picked from commit 8cbf869a0a278c4d39e50daa4f4101b394a72a93)
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

ARM: shmobile: marzen: Consistently use tabs for indentation

Unify white space usage by consistently using tabs for indentation.

Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
(cherry picked from commit 08af64097d4c5cb17f9df4dadf80ed5f508db743)
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

ARM: shmobile: kzm9g-reference: Remove early_printk from command line

As early printk is not supported when devices are initialised
using DT, so remove it from the command line.

Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
(cherry picked from commit 0b7324706ea24489a0ddcbd9d472e232520aad80)
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

ARM: shmobile: armadillo800eva-reference: Remove early_printk from command line

As early printk is not supported when devices are initialised
using DT, so remove it from the command line.

Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
(cherry picked from commit b2386fa51696ffcae82f27ebbdc667b037be5048)
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

ARM: shmobile: r8a7779: Consistently use tabs for indentation

Unify white space usage by consistently using tabs for indentation.

Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
(cherry picked from commit cc703a59c0f8769456a7eb0d53a8d709e5c19387)
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

ARM: shmobile: henninger: Consistently use tabs for indentation

Unify white space usage by consistently using tabs for indentation.

Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
(cherry picked from commit eb0f12e24f357f1663b4da8c571214d5a11eb011)
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

ARM: shmobile: henninger: enable internal PCI

Enable internal AHB-PCI bridges for the USB EHCI/OHCI controllers attached to
them.

Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
[horms+renesas@verge.net.au: minor witespace changes]
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
(cherry picked from commit 83ccfa8d0c6a734720ed8cd23b97256ffcae156a)
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

ARM: shmobile: koelsch: enable internal PCI

Enable internal AHB-PCI bridges for the USB EHCI/OHCI controllers attached to
them.

Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
[horms+renesas@verge.net.au: minor witespace changes]
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
(cherry picked from commit 7540aeb0dd2c830ed490e7227d51bc3050ac798c)
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

ARM: shmobile: r8a7791: add internal PCI bridge nodes

Add device nodes for the R8A7791 internal PCI bridge devices.

Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
[horms+renesas@verge.net.au: minor witespace changes]
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
(cherry picked from commit aace0809e9bbbfe1570a298a3284d9802fbf2d1a)
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

ARM: shmobile: fix shmobile_smp_apmu_suspend_init build failure for !SUSPEND

Patch d6d757c9a4e ("ARM: shmobile: APMU: Add Core-Standby-state for
Suspend to RAM") added both an inline wrapper for shmobile_smp_apmu_suspend_init
and an empty function in arch/arm/mach-shmobile/platsmp-apmu.c. We get a
build failure when both are present, so this patch removes the one in the .c
file and keeps the inline version.

Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
(cherry picked from commit d358c99838f3cf63ad7536124be4318cc84b11fa)
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>