From f9d15dc6a7a69e07f7e363304a0871a9485d5637 Mon Sep 17 00:00:00 2001 From: "Luis R. Rodriguez" Date: Mon, 3 Oct 2011 15:48:26 -0700 Subject: [PATCH] crda: synch up nl80211.h Signed-off-by: Luis R. Rodriguez --- nl80211.h | 1964 +++++++++++++++++++++++++++++++++++++++++++++++++++++++++++-- 1 file changed, 1916 insertions(+), 48 deletions(-) diff --git a/nl80211.h b/nl80211.h index 04d4516..9d797f2 100644 --- a/nl80211.h +++ b/nl80211.h @@ -3,11 +3,11 @@ /* * 802.11 netlink interface public header * - * Copyright 2006, 2007, 2008 Johannes Berg + * Copyright 2006-2010 Johannes Berg * Copyright 2008 Michael Wu * Copyright 2008 Luis Carlos Cobo - * Copyright 2008 Michael Buesch - * Copyright 2008 Luis R. Rodriguez + * Copyright 2008 Michael Buesch + * Copyright 2008, 2009 Luis R. Rodriguez * Copyright 2008 Jouni Malinen * Copyright 2008 Colin McCabe * @@ -25,6 +25,8 @@ * */ +#include + /** * DOC: Station handling * @@ -38,6 +40,76 @@ */ /** + * DOC: Frame transmission/registration support + * + * Frame transmission and registration support exists to allow userspace + * management entities such as wpa_supplicant react to management frames + * that are not being handled by the kernel. This includes, for example, + * certain classes of action frames that cannot be handled in the kernel + * for various reasons. + * + * Frame registration is done on a per-interface basis and registrations + * cannot be removed other than by closing the socket. It is possible to + * specify a registration filter to register, for example, only for a + * certain type of action frame. In particular with action frames, those + * that userspace registers for will not be returned as unhandled by the + * driver, so that the registered application has to take responsibility + * for doing that. + * + * The type of frame that can be registered for is also dependent on the + * driver and interface type. The frame types are advertised in wiphy + * attributes so applications know what to expect. + * + * NOTE: When an interface changes type while registrations are active, + * these registrations are ignored until the interface type is + * changed again. This means that changing the interface type can + * lead to a situation that couldn't otherwise be produced, but + * any such registrations will be dormant in the sense that they + * will not be serviced, i.e. they will not receive any frames. + * + * Frame transmission allows userspace to send for example the required + * responses to action frames. It is subject to some sanity checking, + * but many frames can be transmitted. When a frame was transmitted, its + * status is indicated to the sending socket. + * + * For more technical details, see the corresponding command descriptions + * below. + */ + +/** + * DOC: Virtual interface / concurrency capabilities + * + * Some devices are able to operate with virtual MACs, they can have + * more than one virtual interface. The capability handling for this + * is a bit complex though, as there may be a number of restrictions + * on the types of concurrency that are supported. + * + * To start with, each device supports the interface types listed in + * the %NL80211_ATTR_SUPPORTED_IFTYPES attribute, but by listing the + * types there no concurrency is implied. + * + * Once concurrency is desired, more attributes must be observed: + * To start with, since some interface types are purely managed in + * software, like the AP-VLAN type in mac80211 for example, there's + * an additional list of these, they can be added at any time and + * are only restricted by some semantic restrictions (e.g. AP-VLAN + * cannot be added without a corresponding AP interface). This list + * is exported in the %NL80211_ATTR_SOFTWARE_IFTYPES attribute. + * + * Further, the list of supported combinations is exported. This is + * in the %NL80211_ATTR_INTERFACE_COMBINATIONS attribute. Basically, + * it exports a list of "groups", and at any point in time the + * interfaces that are currently active must fall into any one of + * the advertised groups. Within each group, there are restrictions + * on the number of interfaces of different types that are supported + * and also the number of different channels, along with potentially + * some other restrictions. See &enum nl80211_if_combination_attrs. + * + * All together, these attributes define the concurrency of virtual + * interfaces that a given device supports. + */ + +/** * enum nl80211_commands - supported nl80211 commands * * @NL80211_CMD_UNSPEC: unspecified command to catch errors @@ -46,8 +118,12 @@ * to get a list of all present wiphys. * @NL80211_CMD_SET_WIPHY: set wiphy parameters, needs %NL80211_ATTR_WIPHY or * %NL80211_ATTR_IFINDEX; can be used to set %NL80211_ATTR_WIPHY_NAME, - * %NL80211_ATTR_WIPHY_TXQ_PARAMS, %NL80211_ATTR_WIPHY_FREQ, and/or - * %NL80211_ATTR_WIPHY_SEC_CHAN_OFFSET. + * %NL80211_ATTR_WIPHY_TXQ_PARAMS, %NL80211_ATTR_WIPHY_FREQ, + * %NL80211_ATTR_WIPHY_CHANNEL_TYPE, %NL80211_ATTR_WIPHY_RETRY_SHORT, + * %NL80211_ATTR_WIPHY_RETRY_LONG, %NL80211_ATTR_WIPHY_FRAG_THRESHOLD, + * and/or %NL80211_ATTR_WIPHY_RTS_THRESHOLD. + * However, for setting the channel, see %NL80211_CMD_SET_CHANNEL + * instead, the support here is for backward compatibility only. * @NL80211_CMD_NEW_WIPHY: Newly created wiphy, response to get request * or rename notification. Has attributes %NL80211_ATTR_WIPHY and * %NL80211_ATTR_WIPHY_NAME. @@ -72,11 +148,11 @@ * * @NL80211_CMD_GET_KEY: Get sequence counter information for a key specified * by %NL80211_ATTR_KEY_IDX and/or %NL80211_ATTR_MAC. - * @NL80211_CMD_SET_KEY: Set key attributes %NL80211_ATTR_KEY_DEFAULT or - * %NL80211_ATTR_KEY_THRESHOLD. + * @NL80211_CMD_SET_KEY: Set key attributes %NL80211_ATTR_KEY_DEFAULT, + * %NL80211_ATTR_KEY_DEFAULT_MGMT, or %NL80211_ATTR_KEY_THRESHOLD. * @NL80211_CMD_NEW_KEY: add a key with given %NL80211_ATTR_KEY_DATA, - * %NL80211_ATTR_KEY_IDX, %NL80211_ATTR_MAC and %NL80211_ATTR_KEY_CIPHER - * attributes. + * %NL80211_ATTR_KEY_IDX, %NL80211_ATTR_MAC, %NL80211_ATTR_KEY_CIPHER, + * and %NL80211_ATTR_KEY_SEQ attributes. * @NL80211_CMD_DEL_KEY: delete a key identified by %NL80211_ATTR_KEY_IDX * or %NL80211_ATTR_MAC. * @@ -84,7 +160,14 @@ * %NL80222_CMD_NEW_BEACON message) * @NL80211_CMD_SET_BEACON: set the beacon on an access point interface * using the %NL80211_ATTR_BEACON_INTERVAL, %NL80211_ATTR_DTIM_PERIOD, - * %NL80211_BEACON_HEAD and %NL80211_BEACON_TAIL attributes. + * %NL80211_ATTR_BEACON_HEAD and %NL80211_ATTR_BEACON_TAIL attributes. + * Following attributes are provided for drivers that generate full Beacon + * and Probe Response frames internally: %NL80211_ATTR_SSID, + * %NL80211_ATTR_HIDDEN_SSID, %NL80211_ATTR_CIPHERS_PAIRWISE, + * %NL80211_ATTR_CIPHER_GROUP, %NL80211_ATTR_WPA_VERSIONS, + * %NL80211_ATTR_AKM_SUITES, %NL80211_ATTR_PRIVACY, + * %NL80211_ATTR_AUTH_TYPE, %NL80211_ATTR_IE, %NL80211_ATTR_IE_PROBE_RESP, + * %NL80211_ATTR_IE_ASSOC_RESP. * @NL80211_CMD_NEW_BEACON: add a new beacon to an access point interface, * parameters are like for %NL80211_CMD_SET_BEACON. * @NL80211_CMD_DEL_BEACON: remove the beacon, stop sending it @@ -105,6 +188,10 @@ * @NL80211_CMD_SET_MPATH: Set mesh path attributes for mesh path to * destination %NL80211_ATTR_MAC on the interface identified by * %NL80211_ATTR_IFINDEX. + * @NL80211_CMD_NEW_MPATH: Create a new mesh path for the destination given by + * %NL80211_ATTR_MAC via %NL80211_ATTR_MPATH_NEXT_HOP. + * @NL80211_CMD_DEL_MPATH: Delete a mesh path to the destination given by + * %NL80211_ATTR_MAC. * @NL80211_CMD_NEW_PATH: Add a mesh path with given attributes to the * the interface identified by %NL80211_ATTR_IFINDEX. * @NL80211_CMD_DEL_PATH: Remove a mesh path identified by %NL80211_ATTR_MAC @@ -113,6 +200,8 @@ * @NL80211_CMD_SET_BSS: Set BSS attributes for BSS identified by * %NL80211_ATTR_IFINDEX. * + * @NL80211_CMD_GET_REG: ask the wireless core to send us its currently set + * regulatory domain. * @NL80211_CMD_SET_REG: Set current regulatory domain. CRDA sends this command * after being queried by the kernel. CRDA replies by sending a regulatory * domain structure which consists of %NL80211_ATTR_REG_ALPHA set to our @@ -124,20 +213,307 @@ * %NL80211_ATTR_REG_RULE_POWER_MAX_ANT_GAIN and * %NL80211_ATTR_REG_RULE_POWER_MAX_EIRP. * @NL80211_CMD_REQ_SET_REG: ask the wireless core to set the regulatory domain - * to the the specified ISO/IEC 3166-1 alpha2 country code. The core will + * to the specified ISO/IEC 3166-1 alpha2 country code. The core will * store this as a valid request and then query userspace for it. * - * @NL80211_CMD_GET_MESH_PARAMS: Get mesh networking properties for the + * @NL80211_CMD_GET_MESH_CONFIG: Get mesh networking properties for the * interface identified by %NL80211_ATTR_IFINDEX * - * @NL80211_CMD_SET_MESH_PARAMS: Set mesh networking properties for the + * @NL80211_CMD_SET_MESH_CONFIG: Set mesh networking properties for the * interface identified by %NL80211_ATTR_IFINDEX * + * @NL80211_CMD_SET_MGMT_EXTRA_IE: Set extra IEs for management frames. The + * interface is identified with %NL80211_ATTR_IFINDEX and the management + * frame subtype with %NL80211_ATTR_MGMT_SUBTYPE. The extra IE data to be + * added to the end of the specified management frame is specified with + * %NL80211_ATTR_IE. If the command succeeds, the requested data will be + * added to all specified management frames generated by + * kernel/firmware/driver. + * Note: This command has been removed and it is only reserved at this + * point to avoid re-using existing command number. The functionality this + * command was planned for has been provided with cleaner design with the + * option to specify additional IEs in NL80211_CMD_TRIGGER_SCAN, + * NL80211_CMD_AUTHENTICATE, NL80211_CMD_ASSOCIATE, + * NL80211_CMD_DEAUTHENTICATE, and NL80211_CMD_DISASSOCIATE. + * + * @NL80211_CMD_GET_SCAN: get scan results + * @NL80211_CMD_TRIGGER_SCAN: trigger a new scan with the given parameters + * %NL80211_ATTR_TX_NO_CCK_RATE is used to decide whether to send the + * probe requests at CCK rate or not. + * @NL80211_CMD_NEW_SCAN_RESULTS: scan notification (as a reply to + * NL80211_CMD_GET_SCAN and on the "scan" multicast group) + * @NL80211_CMD_SCAN_ABORTED: scan was aborted, for unspecified reasons, + * partial scan results may be available + * + * @NL80211_CMD_START_SCHED_SCAN: start a scheduled scan at certain + * intervals, as specified by %NL80211_ATTR_SCHED_SCAN_INTERVAL. + * Like with normal scans, if SSIDs (%NL80211_ATTR_SCAN_SSIDS) + * are passed, they are used in the probe requests. For + * broadcast, a broadcast SSID must be passed (ie. an empty + * string). If no SSID is passed, no probe requests are sent and + * a passive scan is performed. %NL80211_ATTR_SCAN_FREQUENCIES, + * if passed, define which channels should be scanned; if not + * passed, all channels allowed for the current regulatory domain + * are used. Extra IEs can also be passed from the userspace by + * using the %NL80211_ATTR_IE attribute. + * @NL80211_CMD_STOP_SCHED_SCAN: stop a scheduled scan. Returns -ENOENT + * if scheduled scan is not running. + * @NL80211_CMD_SCHED_SCAN_RESULTS: indicates that there are scheduled scan + * results available. + * @NL80211_CMD_SCHED_SCAN_STOPPED: indicates that the scheduled scan has + * stopped. The driver may issue this event at any time during a + * scheduled scan. One reason for stopping the scan is if the hardware + * does not support starting an association or a normal scan while running + * a scheduled scan. This event is also sent when the + * %NL80211_CMD_STOP_SCHED_SCAN command is received or when the interface + * is brought down while a scheduled scan was running. + * + * @NL80211_CMD_GET_SURVEY: get survey resuls, e.g. channel occupation + * or noise level + * @NL80211_CMD_NEW_SURVEY_RESULTS: survey data notification (as a reply to + * NL80211_CMD_GET_SURVEY and on the "scan" multicast group) + * + * @NL80211_CMD_REG_CHANGE: indicates to userspace the regulatory domain + * has been changed and provides details of the request information + * that caused the change such as who initiated the regulatory request + * (%NL80211_ATTR_REG_INITIATOR), the wiphy_idx + * (%NL80211_ATTR_REG_ALPHA2) on which the request was made from if + * the initiator was %NL80211_REGDOM_SET_BY_COUNTRY_IE or + * %NL80211_REGDOM_SET_BY_DRIVER, the type of regulatory domain + * set (%NL80211_ATTR_REG_TYPE), if the type of regulatory domain is + * %NL80211_REG_TYPE_COUNTRY the alpha2 to which we have moved on + * to (%NL80211_ATTR_REG_ALPHA2). + * @NL80211_CMD_REG_BEACON_HINT: indicates to userspace that an AP beacon + * has been found while world roaming thus enabling active scan or + * any mode of operation that initiates TX (beacons) on a channel + * where we would not have been able to do either before. As an example + * if you are world roaming (regulatory domain set to world or if your + * driver is using a custom world roaming regulatory domain) and while + * doing a passive scan on the 5 GHz band you find an AP there (if not + * on a DFS channel) you will now be able to actively scan for that AP + * or use AP mode on your card on that same channel. Note that this will + * never be used for channels 1-11 on the 2 GHz band as they are always + * enabled world wide. This beacon hint is only sent if your device had + * either disabled active scanning or beaconing on a channel. We send to + * userspace the wiphy on which we removed a restriction from + * (%NL80211_ATTR_WIPHY) and the channel on which this occurred + * before (%NL80211_ATTR_FREQ_BEFORE) and after (%NL80211_ATTR_FREQ_AFTER) + * the beacon hint was processed. + * + * @NL80211_CMD_AUTHENTICATE: authentication request and notification. + * This command is used both as a command (request to authenticate) and + * as an event on the "mlme" multicast group indicating completion of the + * authentication process. + * When used as a command, %NL80211_ATTR_IFINDEX is used to identify the + * interface. %NL80211_ATTR_MAC is used to specify PeerSTAAddress (and + * BSSID in case of station mode). %NL80211_ATTR_SSID is used to specify + * the SSID (mainly for association, but is included in authentication + * request, too, to help BSS selection. %NL80211_ATTR_WIPHY_FREQ is used + * to specify the frequence of the channel in MHz. %NL80211_ATTR_AUTH_TYPE + * is used to specify the authentication type. %NL80211_ATTR_IE is used to + * define IEs (VendorSpecificInfo, but also including RSN IE and FT IEs) + * to be added to the frame. + * When used as an event, this reports reception of an Authentication + * frame in station and IBSS modes when the local MLME processed the + * frame, i.e., it was for the local STA and was received in correct + * state. This is similar to MLME-AUTHENTICATE.confirm primitive in the + * MLME SAP interface (kernel providing MLME, userspace SME). The + * included %NL80211_ATTR_FRAME attribute contains the management frame + * (including both the header and frame body, but not FCS). This event is + * also used to indicate if the authentication attempt timed out. In that + * case the %NL80211_ATTR_FRAME attribute is replaced with a + * %NL80211_ATTR_TIMED_OUT flag (and %NL80211_ATTR_MAC to indicate which + * pending authentication timed out). + * @NL80211_CMD_ASSOCIATE: association request and notification; like + * NL80211_CMD_AUTHENTICATE but for Association and Reassociation + * (similar to MLME-ASSOCIATE.request, MLME-REASSOCIATE.request, + * MLME-ASSOCIATE.confirm or MLME-REASSOCIATE.confirm primitives). + * @NL80211_CMD_DEAUTHENTICATE: deauthentication request and notification; like + * NL80211_CMD_AUTHENTICATE but for Deauthentication frames (similar to + * MLME-DEAUTHENTICATION.request and MLME-DEAUTHENTICATE.indication + * primitives). + * @NL80211_CMD_DISASSOCIATE: disassociation request and notification; like + * NL80211_CMD_AUTHENTICATE but for Disassociation frames (similar to + * MLME-DISASSOCIATE.request and MLME-DISASSOCIATE.indication primitives). + * + * @NL80211_CMD_MICHAEL_MIC_FAILURE: notification of a locally detected Michael + * MIC (part of TKIP) failure; sent on the "mlme" multicast group; the + * event includes %NL80211_ATTR_MAC to describe the source MAC address of + * the frame with invalid MIC, %NL80211_ATTR_KEY_TYPE to show the key + * type, %NL80211_ATTR_KEY_IDX to indicate the key identifier, and + * %NL80211_ATTR_KEY_SEQ to indicate the TSC value of the frame; this + * event matches with MLME-MICHAELMICFAILURE.indication() primitive + * + * @NL80211_CMD_JOIN_IBSS: Join a new IBSS -- given at least an SSID and a + * FREQ attribute (for the initial frequency if no peer can be found) + * and optionally a MAC (as BSSID) and FREQ_FIXED attribute if those + * should be fixed rather than automatically determined. Can only be + * executed on a network interface that is UP, and fixed BSSID/FREQ + * may be rejected. Another optional parameter is the beacon interval, + * given in the %NL80211_ATTR_BEACON_INTERVAL attribute, which if not + * given defaults to 100 TU (102.4ms). + * @NL80211_CMD_LEAVE_IBSS: Leave the IBSS -- no special arguments, the IBSS is + * determined by the network interface. + * + * @NL80211_CMD_TESTMODE: testmode command, takes a wiphy (or ifindex) attribute + * to identify the device, and the TESTDATA blob attribute to pass through + * to the driver. + * + * @NL80211_CMD_CONNECT: connection request and notification; this command + * requests to connect to a specified network but without separating + * auth and assoc steps. For this, you need to specify the SSID in a + * %NL80211_ATTR_SSID attribute, and can optionally specify the association + * IEs in %NL80211_ATTR_IE, %NL80211_ATTR_AUTH_TYPE, %NL80211_ATTR_MAC, + * %NL80211_ATTR_WIPHY_FREQ, %NL80211_ATTR_CONTROL_PORT, + * %NL80211_ATTR_CONTROL_PORT_ETHERTYPE and + * %NL80211_ATTR_CONTROL_PORT_NO_ENCRYPT. + * It is also sent as an event, with the BSSID and response IEs when the + * connection is established or failed to be established. This can be + * determined by the STATUS_CODE attribute. + * @NL80211_CMD_ROAM: request that the card roam (currently not implemented), + * sent as an event when the card/driver roamed by itself. + * @NL80211_CMD_DISCONNECT: drop a given connection; also used to notify + * userspace that a connection was dropped by the AP or due to other + * reasons, for this the %NL80211_ATTR_DISCONNECTED_BY_AP and + * %NL80211_ATTR_REASON_CODE attributes are used. + * + * @NL80211_CMD_SET_WIPHY_NETNS: Set a wiphy's netns. Note that all devices + * associated with this wiphy must be down and will follow. + * + * @NL80211_CMD_REMAIN_ON_CHANNEL: Request to remain awake on the specified + * channel for the specified amount of time. This can be used to do + * off-channel operations like transmit a Public Action frame and wait for + * a response while being associated to an AP on another channel. + * %NL80211_ATTR_IFINDEX is used to specify which interface (and thus + * radio) is used. %NL80211_ATTR_WIPHY_FREQ is used to specify the + * frequency for the operation and %NL80211_ATTR_WIPHY_CHANNEL_TYPE may be + * optionally used to specify additional channel parameters. + * %NL80211_ATTR_DURATION is used to specify the duration in milliseconds + * to remain on the channel. This command is also used as an event to + * notify when the requested duration starts (it may take a while for the + * driver to schedule this time due to other concurrent needs for the + * radio). + * When called, this operation returns a cookie (%NL80211_ATTR_COOKIE) + * that will be included with any events pertaining to this request; + * the cookie is also used to cancel the request. + * @NL80211_CMD_CANCEL_REMAIN_ON_CHANNEL: This command can be used to cancel a + * pending remain-on-channel duration if the desired operation has been + * completed prior to expiration of the originally requested duration. + * %NL80211_ATTR_WIPHY or %NL80211_ATTR_IFINDEX is used to specify the + * radio. The %NL80211_ATTR_COOKIE attribute must be given as well to + * uniquely identify the request. + * This command is also used as an event to notify when a requested + * remain-on-channel duration has expired. + * + * @NL80211_CMD_SET_TX_BITRATE_MASK: Set the mask of rates to be used in TX + * rate selection. %NL80211_ATTR_IFINDEX is used to specify the interface + * and @NL80211_ATTR_TX_RATES the set of allowed rates. + * + * @NL80211_CMD_REGISTER_FRAME: Register for receiving certain mgmt frames + * (via @NL80211_CMD_FRAME) for processing in userspace. This command + * requires an interface index, a frame type attribute (optional for + * backward compatibility reasons, if not given assumes action frames) + * and a match attribute containing the first few bytes of the frame + * that should match, e.g. a single byte for only a category match or + * four bytes for vendor frames including the OUI. The registration + * cannot be dropped, but is removed automatically when the netlink + * socket is closed. Multiple registrations can be made. + * @NL80211_CMD_REGISTER_ACTION: Alias for @NL80211_CMD_REGISTER_FRAME for + * backward compatibility + * @NL80211_CMD_FRAME: Management frame TX request and RX notification. This + * command is used both as a request to transmit a management frame and + * as an event indicating reception of a frame that was not processed in + * kernel code, but is for us (i.e., which may need to be processed in a + * user space application). %NL80211_ATTR_FRAME is used to specify the + * frame contents (including header). %NL80211_ATTR_WIPHY_FREQ (and + * optionally %NL80211_ATTR_WIPHY_CHANNEL_TYPE) is used to indicate on + * which channel the frame is to be transmitted or was received. If this + * channel is not the current channel (remain-on-channel or the + * operational channel) the device will switch to the given channel and + * transmit the frame, optionally waiting for a response for the time + * specified using %NL80211_ATTR_DURATION. When called, this operation + * returns a cookie (%NL80211_ATTR_COOKIE) that will be included with the + * TX status event pertaining to the TX request. + * %NL80211_ATTR_TX_NO_CCK_RATE is used to decide whether to send the + * management frames at CCK rate or not in 2GHz band. + * @NL80211_CMD_FRAME_WAIT_CANCEL: When an off-channel TX was requested, this + * command may be used with the corresponding cookie to cancel the wait + * time if it is known that it is no longer necessary. + * @NL80211_CMD_ACTION: Alias for @NL80211_CMD_FRAME for backward compatibility. + * @NL80211_CMD_FRAME_TX_STATUS: Report TX status of a management frame + * transmitted with %NL80211_CMD_FRAME. %NL80211_ATTR_COOKIE identifies + * the TX command and %NL80211_ATTR_FRAME includes the contents of the + * frame. %NL80211_ATTR_ACK flag is included if the recipient acknowledged + * the frame. + * @NL80211_CMD_ACTION_TX_STATUS: Alias for @NL80211_CMD_FRAME_TX_STATUS for + * backward compatibility. + * @NL80211_CMD_SET_CQM: Connection quality monitor configuration. This command + * is used to configure connection quality monitoring notification trigger + * levels. + * @NL80211_CMD_NOTIFY_CQM: Connection quality monitor notification. This + * command is used as an event to indicate the that a trigger level was + * reached. + * @NL80211_CMD_SET_CHANNEL: Set the channel (using %NL80211_ATTR_WIPHY_FREQ + * and %NL80211_ATTR_WIPHY_CHANNEL_TYPE) the given interface (identifed + * by %NL80211_ATTR_IFINDEX) shall operate on. + * In case multiple channels are supported by the device, the mechanism + * with which it switches channels is implementation-defined. + * When a monitor interface is given, it can only switch channel while + * no other interfaces are operating to avoid disturbing the operation + * of any other interfaces, and other interfaces will again take + * precedence when they are used. + * + * @NL80211_CMD_SET_WDS_PEER: Set the MAC address of the peer on a WDS interface. + * + * @NL80211_CMD_JOIN_MESH: Join a mesh. The mesh ID must be given, and initial + * mesh config parameters may be given. + * @NL80211_CMD_LEAVE_MESH: Leave the mesh network -- no special arguments, the + * network is determined by the network interface. + * + * @NL80211_CMD_UNPROT_DEAUTHENTICATE: Unprotected deauthentication frame + * notification. This event is used to indicate that an unprotected + * deauthentication frame was dropped when MFP is in use. + * @NL80211_CMD_UNPROT_DISASSOCIATE: Unprotected disassociation frame + * notification. This event is used to indicate that an unprotected + * disassociation frame was dropped when MFP is in use. + * + * @NL80211_CMD_NEW_PEER_CANDIDATE: Notification on the reception of a + * beacon or probe response from a compatible mesh peer. This is only + * sent while no station information (sta_info) exists for the new peer + * candidate and when @NL80211_MESH_SETUP_USERSPACE_AUTH is set. On + * reception of this notification, userspace may decide to create a new + * station (@NL80211_CMD_NEW_STATION). To stop this notification from + * reoccurring, the userspace authentication daemon may want to create the + * new station with the AUTHENTICATED flag unset and maybe change it later + * depending on the authentication result. + * + * @NL80211_CMD_GET_WOWLAN: get Wake-on-Wireless-LAN (WoWLAN) settings. + * @NL80211_CMD_SET_WOWLAN: set Wake-on-Wireless-LAN (WoWLAN) settings. + * Since wireless is more complex than wired ethernet, it supports + * various triggers. These triggers can be configured through this + * command with the %NL80211_ATTR_WOWLAN_TRIGGERS attribute. For + * more background information, see + * http://wireless.kernel.org/en/users/Documentation/WoWLAN. + * + * @NL80211_CMD_SET_REKEY_OFFLOAD: This command is used give the driver + * the necessary information for supporting GTK rekey offload. This + * feature is typically used during WoWLAN. The configuration data + * is contained in %NL80211_ATTR_REKEY_DATA (which is nested and + * contains the data in sub-attributes). After rekeying happened, + * this command may also be sent by the driver as an MLME event to + * inform userspace of the new replay counter. + * + * @NL80211_CMD_PMKSA_CANDIDATE: This is used as an event to inform userspace + * of PMKSA caching dandidates. + * + * @NL80211_CMD_TDLS_OPER: Perform a high-level TDLS command (e.g. link setup). + * @NL80211_CMD_TDLS_MGMT: Send a TDLS management frame. + * * @NL80211_CMD_MAX: highest used command number * @__NL80211_CMD_AFTER_LAST: internal use */ enum nl80211_commands { -/* don't change the order or add anything inbetween, this is ABI! */ +/* don't change the order or add anything between, this is ABI! */ NL80211_CMD_UNSPEC, NL80211_CMD_GET_WIPHY, /* can dump */ @@ -175,8 +551,92 @@ enum nl80211_commands { NL80211_CMD_SET_REG, NL80211_CMD_REQ_SET_REG, - NL80211_CMD_GET_MESH_PARAMS, - NL80211_CMD_SET_MESH_PARAMS, + NL80211_CMD_GET_MESH_CONFIG, + NL80211_CMD_SET_MESH_CONFIG, + + NL80211_CMD_SET_MGMT_EXTRA_IE /* reserved; not used */, + + NL80211_CMD_GET_REG, + + NL80211_CMD_GET_SCAN, + NL80211_CMD_TRIGGER_SCAN, + NL80211_CMD_NEW_SCAN_RESULTS, + NL80211_CMD_SCAN_ABORTED, + + NL80211_CMD_REG_CHANGE, + + NL80211_CMD_AUTHENTICATE, + NL80211_CMD_ASSOCIATE, + NL80211_CMD_DEAUTHENTICATE, + NL80211_CMD_DISASSOCIATE, + + NL80211_CMD_MICHAEL_MIC_FAILURE, + + NL80211_CMD_REG_BEACON_HINT, + + NL80211_CMD_JOIN_IBSS, + NL80211_CMD_LEAVE_IBSS, + + NL80211_CMD_TESTMODE, + + NL80211_CMD_CONNECT, + NL80211_CMD_ROAM, + NL80211_CMD_DISCONNECT, + + NL80211_CMD_SET_WIPHY_NETNS, + + NL80211_CMD_GET_SURVEY, + NL80211_CMD_NEW_SURVEY_RESULTS, + + NL80211_CMD_SET_PMKSA, + NL80211_CMD_DEL_PMKSA, + NL80211_CMD_FLUSH_PMKSA, + + NL80211_CMD_REMAIN_ON_CHANNEL, + NL80211_CMD_CANCEL_REMAIN_ON_CHANNEL, + + NL80211_CMD_SET_TX_BITRATE_MASK, + + NL80211_CMD_REGISTER_FRAME, + NL80211_CMD_REGISTER_ACTION = NL80211_CMD_REGISTER_FRAME, + NL80211_CMD_FRAME, + NL80211_CMD_ACTION = NL80211_CMD_FRAME, + NL80211_CMD_FRAME_TX_STATUS, + NL80211_CMD_ACTION_TX_STATUS = NL80211_CMD_FRAME_TX_STATUS, + + NL80211_CMD_SET_POWER_SAVE, + NL80211_CMD_GET_POWER_SAVE, + + NL80211_CMD_SET_CQM, + NL80211_CMD_NOTIFY_CQM, + + NL80211_CMD_SET_CHANNEL, + NL80211_CMD_SET_WDS_PEER, + + NL80211_CMD_FRAME_WAIT_CANCEL, + + NL80211_CMD_JOIN_MESH, + NL80211_CMD_LEAVE_MESH, + + NL80211_CMD_UNPROT_DEAUTHENTICATE, + NL80211_CMD_UNPROT_DISASSOCIATE, + + NL80211_CMD_NEW_PEER_CANDIDATE, + + NL80211_CMD_GET_WOWLAN, + NL80211_CMD_SET_WOWLAN, + + NL80211_CMD_START_SCHED_SCAN, + NL80211_CMD_STOP_SCHED_SCAN, + NL80211_CMD_SCHED_SCAN_RESULTS, + NL80211_CMD_SCHED_SCAN_STOPPED, + + NL80211_CMD_SET_REKEY_OFFLOAD, + + NL80211_CMD_PMKSA_CANDIDATE, + + NL80211_CMD_TDLS_OPER, + NL80211_CMD_TDLS_MGMT, /* add new commands above here */ @@ -190,6 +650,18 @@ enum nl80211_commands { * here */ #define NL80211_CMD_SET_BSS NL80211_CMD_SET_BSS +#define NL80211_CMD_SET_MGMT_EXTRA_IE NL80211_CMD_SET_MGMT_EXTRA_IE +#define NL80211_CMD_REG_CHANGE NL80211_CMD_REG_CHANGE +#define NL80211_CMD_AUTHENTICATE NL80211_CMD_AUTHENTICATE +#define NL80211_CMD_ASSOCIATE NL80211_CMD_ASSOCIATE +#define NL80211_CMD_DEAUTHENTICATE NL80211_CMD_DEAUTHENTICATE +#define NL80211_CMD_DISASSOCIATE NL80211_CMD_DISASSOCIATE +#define NL80211_CMD_REG_BEACON_HINT NL80211_CMD_REG_BEACON_HINT + +/* source-level API compatibility */ +#define NL80211_CMD_GET_MESH_PARAMS NL80211_CMD_GET_MESH_CONFIG +#define NL80211_CMD_SET_MESH_PARAMS NL80211_CMD_SET_MESH_CONFIG +#define NL80211_MESH_SETUP_VENDOR_PATH_SEL_IE NL80211_MESH_SETUP_IE /** * enum nl80211_attrs - nl80211 netlink attributes @@ -201,13 +673,27 @@ enum nl80211_commands { * @NL80211_ATTR_WIPHY_NAME: wiphy name (used for renaming) * @NL80211_ATTR_WIPHY_TXQ_PARAMS: a nested array of TX queue parameters * @NL80211_ATTR_WIPHY_FREQ: frequency of the selected channel in MHz - * @NL80211_ATTR_WIPHY_SEC_CHAN_OFFSET: included with NL80211_ATTR_WIPHY_FREQ + * @NL80211_ATTR_WIPHY_CHANNEL_TYPE: included with NL80211_ATTR_WIPHY_FREQ * if HT20 or HT40 are allowed (i.e., 802.11n disabled if not included): - * NL80211_SEC_CHAN_NO_HT = HT not allowed (i.e., same as not including + * NL80211_CHAN_NO_HT = HT not allowed (i.e., same as not including * this attribute) - * NL80211_SEC_CHAN_DISABLED = HT20 only - * NL80211_SEC_CHAN_BELOW = secondary channel is below the primary channel - * NL80211_SEC_CHAN_ABOVE = secondary channel is above the primary channel + * NL80211_CHAN_HT20 = HT20 only + * NL80211_CHAN_HT40MINUS = secondary channel is below the primary channel + * NL80211_CHAN_HT40PLUS = secondary channel is above the primary channel + * @NL80211_ATTR_WIPHY_RETRY_SHORT: TX retry limit for frames whose length is + * less than or equal to the RTS threshold; allowed range: 1..255; + * dot11ShortRetryLimit; u8 + * @NL80211_ATTR_WIPHY_RETRY_LONG: TX retry limit for frames whose length is + * greater than the RTS threshold; allowed range: 1..255; + * dot11ShortLongLimit; u8 + * @NL80211_ATTR_WIPHY_FRAG_THRESHOLD: fragmentation threshold, i.e., maximum + * length in octets for frames; allowed range: 256..8000, disable + * fragmentation with (u32)-1; dot11FragmentationThreshold; u32 + * @NL80211_ATTR_WIPHY_RTS_THRESHOLD: RTS threshold (TX frames with length + * larger than or equal to this use RTS/CTS handshake); allowed range: + * 0..65536, disable with (u32)-1; dot11RTSThreshold; u32 + * @NL80211_ATTR_WIPHY_COVERAGE_CLASS: Coverage Class as defined by IEEE 802.11 + * section 7.3.2.9; dot11CoverageClass; u8 * * @NL80211_ATTR_IFINDEX: network interface index of the device to operate on * @NL80211_ATTR_IFNAME: network interface name @@ -231,7 +717,7 @@ enum nl80211_commands { * * @NL80211_ATTR_STA_AID: Association ID for the station (u16) * @NL80211_ATTR_STA_FLAGS: flags, nested element with NLA_FLAG attributes of - * &enum nl80211_sta_flags. + * &enum nl80211_sta_flags (deprecated, use %NL80211_ATTR_STA_FLAGS2) * @NL80211_ATTR_STA_LISTEN_INTERVAL: listen interval as defined by * IEEE 802.11 7.3.1.6 (u16). * @NL80211_ATTR_STA_SUPPORTED_RATES: supported rates, array of supported @@ -247,7 +733,7 @@ enum nl80211_commands { * consisting of a nested array. * * @NL80211_ATTR_MESH_ID: mesh id (1-32 bytes). - * @NL80211_ATTR_PLINK_ACTION: action to perform on the mesh peer link. + * @NL80211_ATTR_STA_PLINK_ACTION: action to perform on the mesh peer link. * @NL80211_ATTR_MPATH_NEXT_HOP: MAC address of the next hop for a mesh path. * @NL80211_ATTR_MPATH_INFO: information about a mesh_path, part of mesh path * info given for %NL80211_CMD_GET_MPATH, nested attribute described at @@ -284,11 +770,350 @@ enum nl80211_commands { * supported interface types, each a flag attribute with the number * of the interface mode. * + * @NL80211_ATTR_MGMT_SUBTYPE: Management frame subtype for + * %NL80211_CMD_SET_MGMT_EXTRA_IE. + * + * @NL80211_ATTR_IE: Information element(s) data (used, e.g., with + * %NL80211_CMD_SET_MGMT_EXTRA_IE). + * + * @NL80211_ATTR_MAX_NUM_SCAN_SSIDS: number of SSIDs you can scan with + * a single scan request, a wiphy attribute. + * @NL80211_ATTR_MAX_NUM_SCHED_SCAN_SSIDS: number of SSIDs you can + * scan with a single scheduled scan request, a wiphy attribute. + * @NL80211_ATTR_MAX_SCAN_IE_LEN: maximum length of information elements + * that can be added to a scan request + * @NL80211_ATTR_MAX_SCHED_SCAN_IE_LEN: maximum length of information + * elements that can be added to a scheduled scan request + * @NL80211_ATTR_MAX_MATCH_SETS: maximum number of sets that can be + * used with @NL80211_ATTR_SCHED_SCAN_MATCH, a wiphy attribute. + * + * @NL80211_ATTR_SCAN_FREQUENCIES: nested attribute with frequencies (in MHz) + * @NL80211_ATTR_SCAN_SSIDS: nested attribute with SSIDs, leave out for passive + * scanning and include a zero-length SSID (wildcard) for wildcard scan + * @NL80211_ATTR_BSS: scan result BSS + * + * @NL80211_ATTR_REG_INITIATOR: indicates who requested the regulatory domain + * currently in effect. This could be any of the %NL80211_REGDOM_SET_BY_* + * @NL80211_ATTR_REG_TYPE: indicates the type of the regulatory domain currently + * set. This can be one of the nl80211_reg_type (%NL80211_REGDOM_TYPE_*) + * + * @NL80211_ATTR_SUPPORTED_COMMANDS: wiphy attribute that specifies + * an array of command numbers (i.e. a mapping index to command number) + * that the driver for the given wiphy supports. + * + * @NL80211_ATTR_FRAME: frame data (binary attribute), including frame header + * and body, but not FCS; used, e.g., with NL80211_CMD_AUTHENTICATE and + * NL80211_CMD_ASSOCIATE events + * @NL80211_ATTR_SSID: SSID (binary attribute, 0..32 octets) + * @NL80211_ATTR_AUTH_TYPE: AuthenticationType, see &enum nl80211_auth_type, + * represented as a u32 + * @NL80211_ATTR_REASON_CODE: ReasonCode for %NL80211_CMD_DEAUTHENTICATE and + * %NL80211_CMD_DISASSOCIATE, u16 + * + * @NL80211_ATTR_KEY_TYPE: Key Type, see &enum nl80211_key_type, represented as + * a u32 + * + * @NL80211_ATTR_FREQ_BEFORE: A channel which has suffered a regulatory change + * due to considerations from a beacon hint. This attribute reflects + * the state of the channel _before_ the beacon hint processing. This + * attributes consists of a nested attribute containing + * NL80211_FREQUENCY_ATTR_* + * @NL80211_ATTR_FREQ_AFTER: A channel which has suffered a regulatory change + * due to considerations from a beacon hint. This attribute reflects + * the state of the channel _after_ the beacon hint processing. This + * attributes consists of a nested attribute containing + * NL80211_FREQUENCY_ATTR_* + * + * @NL80211_ATTR_CIPHER_SUITES: a set of u32 values indicating the supported + * cipher suites + * + * @NL80211_ATTR_FREQ_FIXED: a flag indicating the IBSS should not try to look + * for other networks on different channels + * + * @NL80211_ATTR_TIMED_OUT: a flag indicating than an operation timed out; this + * is used, e.g., with %NL80211_CMD_AUTHENTICATE event + * + * @NL80211_ATTR_USE_MFP: Whether management frame protection (IEEE 802.11w) is + * used for the association (&enum nl80211_mfp, represented as a u32); + * this attribute can be used + * with %NL80211_CMD_ASSOCIATE request + * + * @NL80211_ATTR_STA_FLAGS2: Attribute containing a + * &struct nl80211_sta_flag_update. + * + * @NL80211_ATTR_CONTROL_PORT: A flag indicating whether user space controls + * IEEE 802.1X port, i.e., sets/clears %NL80211_STA_FLAG_AUTHORIZED, in + * station mode. If the flag is included in %NL80211_CMD_ASSOCIATE + * request, the driver will assume that the port is unauthorized until + * authorized by user space. Otherwise, port is marked authorized by + * default in station mode. + * @NL80211_ATTR_CONTROL_PORT_ETHERTYPE: A 16-bit value indicating the + * ethertype that will be used for key negotiation. It can be + * specified with the associate and connect commands. If it is not + * specified, the value defaults to 0x888E (PAE, 802.1X). This + * attribute is also used as a flag in the wiphy information to + * indicate that protocols other than PAE are supported. + * @NL80211_ATTR_CONTROL_PORT_NO_ENCRYPT: When included along with + * %NL80211_ATTR_CONTROL_PORT_ETHERTYPE, indicates that the custom + * ethertype frames used for key negotiation must not be encrypted. + * + * @NL80211_ATTR_TESTDATA: Testmode data blob, passed through to the driver. + * We recommend using nested, driver-specific attributes within this. + * + * @NL80211_ATTR_DISCONNECTED_BY_AP: A flag indicating that the DISCONNECT + * event was due to the AP disconnecting the station, and not due to + * a local disconnect request. + * @NL80211_ATTR_STATUS_CODE: StatusCode for the %NL80211_CMD_CONNECT + * event (u16) + * @NL80211_ATTR_PRIVACY: Flag attribute, used with connect(), indicating + * that protected APs should be used. This is also used with NEW_BEACON to + * indicate that the BSS is to use protection. + * + * @NL80211_ATTR_CIPHERS_PAIRWISE: Used with CONNECT, ASSOCIATE, and NEW_BEACON + * to indicate which unicast key ciphers will be used with the connection + * (an array of u32). + * @NL80211_ATTR_CIPHER_GROUP: Used with CONNECT, ASSOCIATE, and NEW_BEACON to + * indicate which group key cipher will be used with the connection (a + * u32). + * @NL80211_ATTR_WPA_VERSIONS: Used with CONNECT, ASSOCIATE, and NEW_BEACON to + * indicate which WPA version(s) the AP we want to associate with is using + * (a u32 with flags from &enum nl80211_wpa_versions). + * @NL80211_ATTR_AKM_SUITES: Used with CONNECT, ASSOCIATE, and NEW_BEACON to + * indicate which key management algorithm(s) to use (an array of u32). + * + * @NL80211_ATTR_REQ_IE: (Re)association request information elements as + * sent out by the card, for ROAM and successful CONNECT events. + * @NL80211_ATTR_RESP_IE: (Re)association response information elements as + * sent by peer, for ROAM and successful CONNECT events. + * + * @NL80211_ATTR_PREV_BSSID: previous BSSID, to be used by in ASSOCIATE + * commands to specify using a reassociate frame + * + * @NL80211_ATTR_KEY: key information in a nested attribute with + * %NL80211_KEY_* sub-attributes + * @NL80211_ATTR_KEYS: array of keys for static WEP keys for connect() + * and join_ibss(), key information is in a nested attribute each + * with %NL80211_KEY_* sub-attributes + * + * @NL80211_ATTR_PID: Process ID of a network namespace. + * + * @NL80211_ATTR_GENERATION: Used to indicate consistent snapshots for + * dumps. This number increases whenever the object list being + * dumped changes, and as such userspace can verify that it has + * obtained a complete and consistent snapshot by verifying that + * all dump messages contain the same generation number. If it + * changed then the list changed and the dump should be repeated + * completely from scratch. + * + * @NL80211_ATTR_4ADDR: Use 4-address frames on a virtual interface + * + * @NL80211_ATTR_SURVEY_INFO: survey information about a channel, part of + * the survey response for %NL80211_CMD_GET_SURVEY, nested attribute + * containing info as possible, see &enum survey_info. + * + * @NL80211_ATTR_PMKID: PMK material for PMKSA caching. + * @NL80211_ATTR_MAX_NUM_PMKIDS: maximum number of PMKIDs a firmware can + * cache, a wiphy attribute. + * + * @NL80211_ATTR_DURATION: Duration of an operation in milliseconds, u32. + * @NL80211_ATTR_MAX_REMAIN_ON_CHANNEL_DURATION: Device attribute that + * specifies the maximum duration that can be requested with the + * remain-on-channel operation, in milliseconds, u32. + * + * @NL80211_ATTR_COOKIE: Generic 64-bit cookie to identify objects. + * + * @NL80211_ATTR_TX_RATES: Nested set of attributes + * (enum nl80211_tx_rate_attributes) describing TX rates per band. The + * enum nl80211_band value is used as the index (nla_type() of the nested + * data. If a band is not included, it will be configured to allow all + * rates based on negotiated supported rates information. This attribute + * is used with %NL80211_CMD_SET_TX_BITRATE_MASK. + * + * @NL80211_ATTR_FRAME_MATCH: A binary attribute which typically must contain + * at least one byte, currently used with @NL80211_CMD_REGISTER_FRAME. + * @NL80211_ATTR_FRAME_TYPE: A u16 indicating the frame type/subtype for the + * @NL80211_CMD_REGISTER_FRAME command. + * @NL80211_ATTR_TX_FRAME_TYPES: wiphy capability attribute, which is a + * nested attribute of %NL80211_ATTR_FRAME_TYPE attributes, containing + * information about which frame types can be transmitted with + * %NL80211_CMD_FRAME. + * @NL80211_ATTR_RX_FRAME_TYPES: wiphy capability attribute, which is a + * nested attribute of %NL80211_ATTR_FRAME_TYPE attributes, containing + * information about which frame types can be registered for RX. + * + * @NL80211_ATTR_ACK: Flag attribute indicating that the frame was + * acknowledged by the recipient. + * + * @NL80211_ATTR_CQM: connection quality monitor configuration in a + * nested attribute with %NL80211_ATTR_CQM_* sub-attributes. + * + * @NL80211_ATTR_LOCAL_STATE_CHANGE: Flag attribute to indicate that a command + * is requesting a local authentication/association state change without + * invoking actual management frame exchange. This can be used with + * NL80211_CMD_AUTHENTICATE, NL80211_CMD_DEAUTHENTICATE, + * NL80211_CMD_DISASSOCIATE. + * + * @NL80211_ATTR_AP_ISOLATE: (AP mode) Do not forward traffic between stations + * connected to this BSS. + * + * @NL80211_ATTR_WIPHY_TX_POWER_SETTING: Transmit power setting type. See + * &enum nl80211_tx_power_setting for possible values. + * @NL80211_ATTR_WIPHY_TX_POWER_LEVEL: Transmit power level in signed mBm units. + * This is used in association with @NL80211_ATTR_WIPHY_TX_POWER_SETTING + * for non-automatic settings. + * + * @NL80211_ATTR_SUPPORT_IBSS_RSN: The device supports IBSS RSN, which mostly + * means support for per-station GTKs. + * + * @NL80211_ATTR_WIPHY_ANTENNA_TX: Bitmap of allowed antennas for transmitting. + * This can be used to mask out antennas which are not attached or should + * not be used for transmitting. If an antenna is not selected in this + * bitmap the hardware is not allowed to transmit on this antenna. + * + * Each bit represents one antenna, starting with antenna 1 at the first + * bit. Depending on which antennas are selected in the bitmap, 802.11n + * drivers can derive which chainmasks to use (if all antennas belonging to + * a particular chain are disabled this chain should be disabled) and if + * a chain has diversity antennas wether diversity should be used or not. + * HT capabilities (STBC, TX Beamforming, Antenna selection) can be + * derived from the available chains after applying the antenna mask. + * Non-802.11n drivers can derive wether to use diversity or not. + * Drivers may reject configurations or RX/TX mask combinations they cannot + * support by returning -EINVAL. + * + * @NL80211_ATTR_WIPHY_ANTENNA_RX: Bitmap of allowed antennas for receiving. + * This can be used to mask out antennas which are not attached or should + * not be used for receiving. If an antenna is not selected in this bitmap + * the hardware should not be configured to receive on this antenna. + * For a more detailed description see @NL80211_ATTR_WIPHY_ANTENNA_TX. + * + * @NL80211_ATTR_WIPHY_ANTENNA_AVAIL_TX: Bitmap of antennas which are available + * for configuration as TX antennas via the above parameters. + * + * @NL80211_ATTR_WIPHY_ANTENNA_AVAIL_RX: Bitmap of antennas which are available + * for configuration as RX antennas via the above parameters. + * + * @NL80211_ATTR_MCAST_RATE: Multicast tx rate (in 100 kbps) for IBSS + * + * @NL80211_ATTR_OFFCHANNEL_TX_OK: For management frame TX, the frame may be + * transmitted on another channel when the channel given doesn't match + * the current channel. If the current channel doesn't match and this + * flag isn't set, the frame will be rejected. This is also used as an + * nl80211 capability flag. + * + * @NL80211_ATTR_BSS_HTOPMODE: HT operation mode (u16) + * + * @NL80211_ATTR_KEY_DEFAULT_TYPES: A nested attribute containing flags + * attributes, specifying what a key should be set as default as. + * See &enum nl80211_key_default_types. + * + * @NL80211_ATTR_MESH_SETUP: Optional mesh setup parameters. These cannot be + * changed once the mesh is active. + * @NL80211_ATTR_MESH_CONFIG: Mesh configuration parameters, a nested attribute + * containing attributes from &enum nl80211_meshconf_params. + * @NL80211_ATTR_SUPPORT_MESH_AUTH: Currently, this means the underlying driver + * allows auth frames in a mesh to be passed to userspace for processing via + * the @NL80211_MESH_SETUP_USERSPACE_AUTH flag. + * @NL80211_ATTR_STA_PLINK_STATE: The state of a mesh peer link as + * defined in &enum nl80211_plink_state. Used when userspace is + * driving the peer link management state machine. + * @NL80211_MESH_SETUP_USERSPACE_AMPE must be enabled. + * + * @NL80211_ATTR_WOWLAN_TRIGGERS_SUPPORTED: indicates, as part of the wiphy + * capabilities, the supported WoWLAN triggers + * @NL80211_ATTR_WOWLAN_TRIGGERS: used by %NL80211_CMD_SET_WOWLAN to + * indicate which WoW triggers should be enabled. This is also + * used by %NL80211_CMD_GET_WOWLAN to get the currently enabled WoWLAN + * triggers. + + * @NL80211_ATTR_SCHED_SCAN_INTERVAL: Interval between scheduled scan + * cycles, in msecs. + + * @NL80211_ATTR_SCHED_SCAN_MATCH: Nested attribute with one or more + * sets of attributes to match during scheduled scans. Only BSSs + * that match any of the sets will be reported. These are + * pass-thru filter rules. + * For a match to succeed, the BSS must match all attributes of a + * set. Since not every hardware supports matching all types of + * attributes, there is no guarantee that the reported BSSs are + * fully complying with the match sets and userspace needs to be + * able to ignore them by itself. + * Thus, the implementation is somewhat hardware-dependent, but + * this is only an optimization and the userspace application + * needs to handle all the non-filtered results anyway. + * If the match attributes don't make sense when combined with + * the values passed in @NL80211_ATTR_SCAN_SSIDS (eg. if an SSID + * is included in the probe request, but the match attributes + * will never let it go through), -EINVAL may be returned. + * If ommited, no filtering is done. + * + * @NL80211_ATTR_INTERFACE_COMBINATIONS: Nested attribute listing the supported + * interface combinations. In each nested item, it contains attributes + * defined in &enum nl80211_if_combination_attrs. + * @NL80211_ATTR_SOFTWARE_IFTYPES: Nested attribute (just like + * %NL80211_ATTR_SUPPORTED_IFTYPES) containing the interface types that + * are managed in software: interfaces of these types aren't subject to + * any restrictions in their number or combinations. + * + * @%NL80211_ATTR_REKEY_DATA: nested attribute containing the information + * necessary for GTK rekeying in the device, see &enum nl80211_rekey_data. + * + * @NL80211_ATTR_SCAN_SUPP_RATES: rates per to be advertised as supported in scan, + * nested array attribute containing an entry for each band, with the entry + * being a list of supported rates as defined by IEEE 802.11 7.3.2.2 but + * without the length restriction (at most %NL80211_MAX_SUPP_RATES). + * + * @NL80211_ATTR_HIDDEN_SSID: indicates whether SSID is to be hidden from Beacon + * and Probe Response (when response to wildcard Probe Request); see + * &enum nl80211_hidden_ssid, represented as a u32 + * + * @NL80211_ATTR_IE_PROBE_RESP: Information element(s) for Probe Response frame. + * This is used with %NL80211_CMD_NEW_BEACON and %NL80211_CMD_SET_BEACON to + * provide extra IEs (e.g., WPS/P2P IE) into Probe Response frames when the + * driver (or firmware) replies to Probe Request frames. + * @NL80211_ATTR_IE_ASSOC_RESP: Information element(s) for (Re)Association + * Response frames. This is used with %NL80211_CMD_NEW_BEACON and + * %NL80211_CMD_SET_BEACON to provide extra IEs (e.g., WPS/P2P IE) into + * (Re)Association Response frames when the driver (or firmware) replies to + * (Re)Association Request frames. + * + * @NL80211_ATTR_STA_WME: Nested attribute containing the wme configuration + * of the station, see &enum nl80211_sta_wme_attr. + * @NL80211_ATTR_SUPPORT_AP_UAPSD: the device supports uapsd when working + * as AP. + * + * @NL80211_ATTR_ROAM_SUPPORT: Indicates whether the firmware is capable of + * roaming to another AP in the same ESS if the signal lever is low. + * + * @NL80211_ATTR_PMKSA_CANDIDATE: Nested attribute containing the PMKSA caching + * candidate information, see &enum nl80211_pmksa_candidate_attr. + * + * @NL80211_ATTR_TX_NO_CCK_RATE: Indicates whether to use CCK rate or not + * for management frames transmission. In order to avoid p2p probe/action + * frames are being transmitted at CCK rate in 2GHz band, the user space + * applications use this attribute. + * This attribute is used with %NL80211_CMD_TRIGGER_SCAN and + * %NL80211_CMD_FRAME commands. + * + * @NL80211_ATTR_TDLS_ACTION: Low level TDLS action code (e.g. link setup + * request, link setup confirm, link teardown, etc.). Values are + * described in the TDLS (802.11z) specification. + * @NL80211_ATTR_TDLS_DIALOG_TOKEN: Non-zero token for uniquely identifying a + * TDLS conversation between two devices. + * @NL80211_ATTR_TDLS_OPERATION: High level TDLS operation; see + * &enum nl80211_tdls_operation, represented as a u8. + * @NL80211_ATTR_TDLS_SUPPORT: A flag indicating the device can operate + * as a TDLS peer sta. + * @NL80211_ATTR_TDLS_EXTERNAL_SETUP: The TDLS discovery/setup and teardown + * procedures should be performed by sending TDLS packets via + * %NL80211_CMD_TDLS_MGMT. Otherwise %NL80211_CMD_TDLS_OPER should be + * used for asking the driver to perform a TDLS operation. + * * @NL80211_ATTR_MAX: highest attribute number currently defined * @__NL80211_ATTR_AFTER_LAST: internal use */ enum nl80211_attrs { -/* don't change the order or add anything inbetween, this is ABI! */ +/* don't change the order or add anything between, this is ABI! */ NL80211_ATTR_UNSPEC, NL80211_ATTR_WIPHY, @@ -338,13 +1163,179 @@ enum nl80211_attrs { NL80211_ATTR_REG_ALPHA2, NL80211_ATTR_REG_RULES, - NL80211_ATTR_MESH_PARAMS, + NL80211_ATTR_MESH_CONFIG, NL80211_ATTR_BSS_BASIC_RATES, NL80211_ATTR_WIPHY_TXQ_PARAMS, NL80211_ATTR_WIPHY_FREQ, - NL80211_ATTR_WIPHY_SEC_CHAN_OFFSET, + NL80211_ATTR_WIPHY_CHANNEL_TYPE, + + NL80211_ATTR_KEY_DEFAULT_MGMT, + + NL80211_ATTR_MGMT_SUBTYPE, + NL80211_ATTR_IE, + + NL80211_ATTR_MAX_NUM_SCAN_SSIDS, + + NL80211_ATTR_SCAN_FREQUENCIES, + NL80211_ATTR_SCAN_SSIDS, + NL80211_ATTR_GENERATION, /* replaces old SCAN_GENERATION */ + NL80211_ATTR_BSS, + + NL80211_ATTR_REG_INITIATOR, + NL80211_ATTR_REG_TYPE, + + NL80211_ATTR_SUPPORTED_COMMANDS, + + NL80211_ATTR_FRAME, + NL80211_ATTR_SSID, + NL80211_ATTR_AUTH_TYPE, + NL80211_ATTR_REASON_CODE, + + NL80211_ATTR_KEY_TYPE, + + NL80211_ATTR_MAX_SCAN_IE_LEN, + NL80211_ATTR_CIPHER_SUITES, + + NL80211_ATTR_FREQ_BEFORE, + NL80211_ATTR_FREQ_AFTER, + + NL80211_ATTR_FREQ_FIXED, + + + NL80211_ATTR_WIPHY_RETRY_SHORT, + NL80211_ATTR_WIPHY_RETRY_LONG, + NL80211_ATTR_WIPHY_FRAG_THRESHOLD, + NL80211_ATTR_WIPHY_RTS_THRESHOLD, + + NL80211_ATTR_TIMED_OUT, + + NL80211_ATTR_USE_MFP, + + NL80211_ATTR_STA_FLAGS2, + + NL80211_ATTR_CONTROL_PORT, + + NL80211_ATTR_TESTDATA, + + NL80211_ATTR_PRIVACY, + + NL80211_ATTR_DISCONNECTED_BY_AP, + NL80211_ATTR_STATUS_CODE, + + NL80211_ATTR_CIPHER_SUITES_PAIRWISE, + NL80211_ATTR_CIPHER_SUITE_GROUP, + NL80211_ATTR_WPA_VERSIONS, + NL80211_ATTR_AKM_SUITES, + + NL80211_ATTR_REQ_IE, + NL80211_ATTR_RESP_IE, + + NL80211_ATTR_PREV_BSSID, + + NL80211_ATTR_KEY, + NL80211_ATTR_KEYS, + + NL80211_ATTR_PID, + + NL80211_ATTR_4ADDR, + + NL80211_ATTR_SURVEY_INFO, + + NL80211_ATTR_PMKID, + NL80211_ATTR_MAX_NUM_PMKIDS, + + NL80211_ATTR_DURATION, + + NL80211_ATTR_COOKIE, + + NL80211_ATTR_WIPHY_COVERAGE_CLASS, + + NL80211_ATTR_TX_RATES, + + NL80211_ATTR_FRAME_MATCH, + + NL80211_ATTR_ACK, + + NL80211_ATTR_PS_STATE, + + NL80211_ATTR_CQM, + + NL80211_ATTR_LOCAL_STATE_CHANGE, + + NL80211_ATTR_AP_ISOLATE, + + NL80211_ATTR_WIPHY_TX_POWER_SETTING, + NL80211_ATTR_WIPHY_TX_POWER_LEVEL, + + NL80211_ATTR_TX_FRAME_TYPES, + NL80211_ATTR_RX_FRAME_TYPES, + NL80211_ATTR_FRAME_TYPE, + + NL80211_ATTR_CONTROL_PORT_ETHERTYPE, + NL80211_ATTR_CONTROL_PORT_NO_ENCRYPT, + + NL80211_ATTR_SUPPORT_IBSS_RSN, + + NL80211_ATTR_WIPHY_ANTENNA_TX, + NL80211_ATTR_WIPHY_ANTENNA_RX, + + NL80211_ATTR_MCAST_RATE, + + NL80211_ATTR_OFFCHANNEL_TX_OK, + + NL80211_ATTR_BSS_HT_OPMODE, + + NL80211_ATTR_KEY_DEFAULT_TYPES, + + NL80211_ATTR_MAX_REMAIN_ON_CHANNEL_DURATION, + + NL80211_ATTR_MESH_SETUP, + + NL80211_ATTR_WIPHY_ANTENNA_AVAIL_TX, + NL80211_ATTR_WIPHY_ANTENNA_AVAIL_RX, + + NL80211_ATTR_SUPPORT_MESH_AUTH, + NL80211_ATTR_STA_PLINK_STATE, + + NL80211_ATTR_WOWLAN_TRIGGERS, + NL80211_ATTR_WOWLAN_TRIGGERS_SUPPORTED, + + NL80211_ATTR_SCHED_SCAN_INTERVAL, + + NL80211_ATTR_INTERFACE_COMBINATIONS, + NL80211_ATTR_SOFTWARE_IFTYPES, + + NL80211_ATTR_REKEY_DATA, + + NL80211_ATTR_MAX_NUM_SCHED_SCAN_SSIDS, + NL80211_ATTR_MAX_SCHED_SCAN_IE_LEN, + + NL80211_ATTR_SCAN_SUPP_RATES, + + NL80211_ATTR_HIDDEN_SSID, + + NL80211_ATTR_IE_PROBE_RESP, + NL80211_ATTR_IE_ASSOC_RESP, + + NL80211_ATTR_STA_WME, + NL80211_ATTR_SUPPORT_AP_UAPSD, + + NL80211_ATTR_ROAM_SUPPORT, + + NL80211_ATTR_SCHED_SCAN_MATCH, + NL80211_ATTR_MAX_MATCH_SETS, + + NL80211_ATTR_PMKSA_CANDIDATE, + + NL80211_ATTR_TX_NO_CCK_RATE, + + NL80211_ATTR_TDLS_ACTION, + NL80211_ATTR_TDLS_DIALOG_TOKEN, + NL80211_ATTR_TDLS_OPERATION, + NL80211_ATTR_TDLS_SUPPORT, + NL80211_ATTR_TDLS_EXTERNAL_SETUP, /* add attributes here, update the policy in nl80211.c */ @@ -352,15 +1343,34 @@ enum nl80211_attrs { NL80211_ATTR_MAX = __NL80211_ATTR_AFTER_LAST - 1 }; +/* source-level API compatibility */ +#define NL80211_ATTR_SCAN_GENERATION NL80211_ATTR_GENERATION +#define NL80211_ATTR_MESH_PARAMS NL80211_ATTR_MESH_CONFIG + /* * Allow user space programs to use #ifdef on new attributes by defining them * here */ +#define NL80211_CMD_CONNECT NL80211_CMD_CONNECT #define NL80211_ATTR_HT_CAPABILITY NL80211_ATTR_HT_CAPABILITY #define NL80211_ATTR_BSS_BASIC_RATES NL80211_ATTR_BSS_BASIC_RATES #define NL80211_ATTR_WIPHY_TXQ_PARAMS NL80211_ATTR_WIPHY_TXQ_PARAMS #define NL80211_ATTR_WIPHY_FREQ NL80211_ATTR_WIPHY_FREQ -#define NL80211_ATTR_WIPHY_SEC_CHAN_OFFSET NL80211_ATTR_WIPHY_SEC_CHAN_OFFSET +#define NL80211_ATTR_WIPHY_CHANNEL_TYPE NL80211_ATTR_WIPHY_CHANNEL_TYPE +#define NL80211_ATTR_MGMT_SUBTYPE NL80211_ATTR_MGMT_SUBTYPE +#define NL80211_ATTR_IE NL80211_ATTR_IE +#define NL80211_ATTR_REG_INITIATOR NL80211_ATTR_REG_INITIATOR +#define NL80211_ATTR_REG_TYPE NL80211_ATTR_REG_TYPE +#define NL80211_ATTR_FRAME NL80211_ATTR_FRAME +#define NL80211_ATTR_SSID NL80211_ATTR_SSID +#define NL80211_ATTR_AUTH_TYPE NL80211_ATTR_AUTH_TYPE +#define NL80211_ATTR_REASON_CODE NL80211_ATTR_REASON_CODE +#define NL80211_ATTR_CIPHER_SUITES_PAIRWISE NL80211_ATTR_CIPHER_SUITES_PAIRWISE +#define NL80211_ATTR_CIPHER_SUITE_GROUP NL80211_ATTR_CIPHER_SUITE_GROUP +#define NL80211_ATTR_WPA_VERSIONS NL80211_ATTR_WPA_VERSIONS +#define NL80211_ATTR_AKM_SUITES NL80211_ATTR_AKM_SUITES +#define NL80211_ATTR_KEY NL80211_ATTR_KEY +#define NL80211_ATTR_KEYS NL80211_ATTR_KEYS #define NL80211_MAX_SUPP_RATES 32 #define NL80211_MAX_SUPP_REG_RULES 32 @@ -369,6 +1379,9 @@ enum nl80211_attrs { #define NL80211_TKIP_DATA_OFFSET_RX_MIC_KEY 24 #define NL80211_HT_CAPABILITY_LEN 26 +#define NL80211_MAX_NR_CIPHER_SUITES 5 +#define NL80211_MAX_NR_AKM_SUITES 2 + /** * enum nl80211_iftype - (virtual) interface types * @@ -376,12 +1389,16 @@ enum nl80211_attrs { * @NL80211_IFTYPE_ADHOC: independent BSS member * @NL80211_IFTYPE_STATION: managed BSS member * @NL80211_IFTYPE_AP: access point - * @NL80211_IFTYPE_AP_VLAN: VLAN interface for access points + * @NL80211_IFTYPE_AP_VLAN: VLAN interface for access points; VLAN interfaces + * are a bit special in that they must always be tied to a pre-existing + * AP type interface. * @NL80211_IFTYPE_WDS: wireless distribution interface * @NL80211_IFTYPE_MONITOR: monitor interface receiving all frames * @NL80211_IFTYPE_MESH_POINT: mesh point + * @NL80211_IFTYPE_P2P_CLIENT: P2P client + * @NL80211_IFTYPE_P2P_GO: P2P group owner * @NL80211_IFTYPE_MAX: highest interface type number currently defined - * @__NL80211_IFTYPE_AFTER_LAST: internal use + * @NUM_NL80211_IFTYPES: number of defined interface types * * These values are used with the %NL80211_ATTR_IFTYPE * to set the type of an interface. @@ -396,10 +1413,12 @@ enum nl80211_iftype { NL80211_IFTYPE_WDS, NL80211_IFTYPE_MONITOR, NL80211_IFTYPE_MESH_POINT, + NL80211_IFTYPE_P2P_CLIENT, + NL80211_IFTYPE_P2P_GO, /* keep last */ - __NL80211_IFTYPE_AFTER_LAST, - NL80211_IFTYPE_MAX = __NL80211_IFTYPE_AFTER_LAST - 1 + NUM_NL80211_IFTYPES, + NL80211_IFTYPE_MAX = NUM_NL80211_IFTYPES - 1 }; /** @@ -408,16 +1427,25 @@ enum nl80211_iftype { * Station flags. When a station is added to an AP interface, it is * assumed to be already associated (and hence authenticated.) * + * @__NL80211_STA_FLAG_INVALID: attribute number 0 is reserved * @NL80211_STA_FLAG_AUTHORIZED: station is authorized (802.1X) * @NL80211_STA_FLAG_SHORT_PREAMBLE: station is capable of receiving frames * with short barker preamble * @NL80211_STA_FLAG_WME: station is WME/QoS capable + * @NL80211_STA_FLAG_MFP: station uses management frame protection + * @NL80211_STA_FLAG_AUTHENTICATED: station is authenticated + * @NL80211_STA_FLAG_TDLS_PEER: station is a TDLS peer + * @NL80211_STA_FLAG_MAX: highest station flag number currently defined + * @__NL80211_STA_FLAG_AFTER_LAST: internal use */ enum nl80211_sta_flags { __NL80211_STA_FLAG_INVALID, NL80211_STA_FLAG_AUTHORIZED, NL80211_STA_FLAG_SHORT_PREAMBLE, NL80211_STA_FLAG_WME, + NL80211_STA_FLAG_MFP, + NL80211_STA_FLAG_AUTHENTICATED, + NL80211_STA_FLAG_TDLS_PEER, /* keep last */ __NL80211_STA_FLAG_AFTER_LAST, @@ -425,6 +1453,74 @@ enum nl80211_sta_flags { }; /** + * struct nl80211_sta_flag_update - station flags mask/set + * @mask: mask of station flags to set + * @set: which values to set them to + * + * Both mask and set contain bits as per &enum nl80211_sta_flags. + */ +struct nl80211_sta_flag_update { + __u32 mask; + __u32 set; +} __attribute__((packed)); + +/** + * enum nl80211_rate_info - bitrate information + * + * These attribute types are used with %NL80211_STA_INFO_TXRATE + * when getting information about the bitrate of a station. + * + * @__NL80211_RATE_INFO_INVALID: attribute number 0 is reserved + * @NL80211_RATE_INFO_BITRATE: total bitrate (u16, 100kbit/s) + * @NL80211_RATE_INFO_MCS: mcs index for 802.11n (u8) + * @NL80211_RATE_INFO_40_MHZ_WIDTH: 40 Mhz dualchannel bitrate + * @NL80211_RATE_INFO_SHORT_GI: 400ns guard interval + * @NL80211_RATE_INFO_MAX: highest rate_info number currently defined + * @__NL80211_RATE_INFO_AFTER_LAST: internal use + */ +enum nl80211_rate_info { + __NL80211_RATE_INFO_INVALID, + NL80211_RATE_INFO_BITRATE, + NL80211_RATE_INFO_MCS, + NL80211_RATE_INFO_40_MHZ_WIDTH, + NL80211_RATE_INFO_SHORT_GI, + + /* keep last */ + __NL80211_RATE_INFO_AFTER_LAST, + NL80211_RATE_INFO_MAX = __NL80211_RATE_INFO_AFTER_LAST - 1 +}; + +/** + * enum nl80211_sta_bss_param - BSS information collected by STA + * + * These attribute types are used with %NL80211_STA_INFO_BSS_PARAM + * when getting information about the bitrate of a station. + * + * @__NL80211_STA_BSS_PARAM_INVALID: attribute number 0 is reserved + * @NL80211_STA_BSS_PARAM_CTS_PROT: whether CTS protection is enabled (flag) + * @NL80211_STA_BSS_PARAM_SHORT_PREAMBLE: whether short preamble is enabled + * (flag) + * @NL80211_STA_BSS_PARAM_SHORT_SLOT_TIME: whether short slot time is enabled + * (flag) + * @NL80211_STA_BSS_PARAM_DTIM_PERIOD: DTIM period for beaconing (u8) + * @NL80211_STA_BSS_PARAM_BEACON_INTERVAL: Beacon interval (u16) + * @NL80211_STA_BSS_PARAM_MAX: highest sta_bss_param number currently defined + * @__NL80211_STA_BSS_PARAM_AFTER_LAST: internal use + */ +enum nl80211_sta_bss_param { + __NL80211_STA_BSS_PARAM_INVALID, + NL80211_STA_BSS_PARAM_CTS_PROT, + NL80211_STA_BSS_PARAM_SHORT_PREAMBLE, + NL80211_STA_BSS_PARAM_SHORT_SLOT_TIME, + NL80211_STA_BSS_PARAM_DTIM_PERIOD, + NL80211_STA_BSS_PARAM_BEACON_INTERVAL, + + /* keep last */ + __NL80211_STA_BSS_PARAM_AFTER_LAST, + NL80211_STA_BSS_PARAM_MAX = __NL80211_STA_BSS_PARAM_AFTER_LAST - 1 +}; + +/** * enum nl80211_sta_info - station information * * These attribute types are used with %NL80211_ATTR_STA_INFO @@ -434,6 +1530,24 @@ enum nl80211_sta_flags { * @NL80211_STA_INFO_INACTIVE_TIME: time since last activity (u32, msecs) * @NL80211_STA_INFO_RX_BYTES: total received bytes (u32, from this station) * @NL80211_STA_INFO_TX_BYTES: total transmitted bytes (u32, to this station) + * @NL80211_STA_INFO_SIGNAL: signal strength of last received PPDU (u8, dBm) + * @NL80211_STA_INFO_TX_BITRATE: current unicast tx rate, nested attribute + * containing info as possible, see &enum nl80211_rate_info + * @NL80211_STA_INFO_RX_PACKETS: total received packet (u32, from this station) + * @NL80211_STA_INFO_TX_PACKETS: total transmitted packets (u32, to this + * station) + * @NL80211_STA_INFO_TX_RETRIES: total retries (u32, to this station) + * @NL80211_STA_INFO_TX_FAILED: total failed packets (u32, to this station) + * @NL80211_STA_INFO_SIGNAL_AVG: signal strength average (u8, dBm) + * @NL80211_STA_INFO_LLID: the station's mesh LLID + * @NL80211_STA_INFO_PLID: the station's mesh PLID + * @NL80211_STA_INFO_PLINK_STATE: peer link state for the station + * (see %enum nl80211_plink_state) + * @NL80211_STA_INFO_RX_BITRATE: last unicast data frame rx rate, nested + * attribute, like NL80211_STA_INFO_TX_BITRATE. + * @NL80211_STA_INFO_BSS_PARAM: current station's view of BSS, nested attribute + * containing info as possible, see &enum nl80211_sta_bss_param + * @NL80211_STA_INFO_CONNECTED_TIME: time since the station is last connected * @__NL80211_STA_INFO_AFTER_LAST: internal * @NL80211_STA_INFO_MAX: highest possible station info attribute */ @@ -445,6 +1559,16 @@ enum nl80211_sta_info { NL80211_STA_INFO_LLID, NL80211_STA_INFO_PLID, NL80211_STA_INFO_PLINK_STATE, + NL80211_STA_INFO_SIGNAL, + NL80211_STA_INFO_TX_BITRATE, + NL80211_STA_INFO_RX_PACKETS, + NL80211_STA_INFO_TX_PACKETS, + NL80211_STA_INFO_TX_RETRIES, + NL80211_STA_INFO_TX_FAILED, + NL80211_STA_INFO_SIGNAL_AVG, + NL80211_STA_INFO_RX_BITRATE, + NL80211_STA_INFO_BSS_PARAM, + NL80211_STA_INFO_CONNECTED_TIME, /* keep last */ __NL80211_STA_INFO_AFTER_LAST, @@ -456,14 +1580,14 @@ enum nl80211_sta_info { * * @NL80211_MPATH_FLAG_ACTIVE: the mesh path is active * @NL80211_MPATH_FLAG_RESOLVING: the mesh path discovery process is running - * @NL80211_MPATH_FLAG_DSN_VALID: the mesh path contains a valid DSN + * @NL80211_MPATH_FLAG_SN_VALID: the mesh path contains a valid SN * @NL80211_MPATH_FLAG_FIXED: the mesh path has been manually set * @NL80211_MPATH_FLAG_RESOLVED: the mesh path discovery process succeeded */ enum nl80211_mpath_flags { NL80211_MPATH_FLAG_ACTIVE = 1<<0, NL80211_MPATH_FLAG_RESOLVING = 1<<1, - NL80211_MPATH_FLAG_DSN_VALID = 1<<2, + NL80211_MPATH_FLAG_SN_VALID = 1<<2, NL80211_MPATH_FLAG_FIXED = 1<<3, NL80211_MPATH_FLAG_RESOLVED = 1<<4, }; @@ -475,19 +1599,22 @@ enum nl80211_mpath_flags { * information about a mesh path. * * @__NL80211_MPATH_INFO_INVALID: attribute number 0 is reserved - * @NL80211_ATTR_MPATH_FRAME_QLEN: number of queued frames for this destination - * @NL80211_ATTR_MPATH_DSN: destination sequence number - * @NL80211_ATTR_MPATH_METRIC: metric (cost) of this mesh path - * @NL80211_ATTR_MPATH_EXPTIME: expiration time for the path, in msec from now - * @NL80211_ATTR_MPATH_FLAGS: mesh path flags, enumerated in + * @NL80211_MPATH_INFO_FRAME_QLEN: number of queued frames for this destination + * @NL80211_MPATH_INFO_SN: destination sequence number + * @NL80211_MPATH_INFO_METRIC: metric (cost) of this mesh path + * @NL80211_MPATH_INFO_EXPTIME: expiration time for the path, in msec from now + * @NL80211_MPATH_INFO_FLAGS: mesh path flags, enumerated in * &enum nl80211_mpath_flags; - * @NL80211_ATTR_MPATH_DISCOVERY_TIMEOUT: total path discovery timeout, in msec - * @NL80211_ATTR_MPATH_DISCOVERY_RETRIES: mesh path discovery retries + * @NL80211_MPATH_INFO_DISCOVERY_TIMEOUT: total path discovery timeout, in msec + * @NL80211_MPATH_INFO_DISCOVERY_RETRIES: mesh path discovery retries + * @NL80211_MPATH_INFO_MAX: highest mesh path information attribute number + * currently defind + * @__NL80211_MPATH_INFO_AFTER_LAST: internal use */ enum nl80211_mpath_info { __NL80211_MPATH_INFO_INVALID, NL80211_MPATH_INFO_FRAME_QLEN, - NL80211_MPATH_INFO_DSN, + NL80211_MPATH_INFO_SN, NL80211_MPATH_INFO_METRIC, NL80211_MPATH_INFO_EXPTIME, NL80211_MPATH_INFO_FLAGS, @@ -511,6 +1638,8 @@ enum nl80211_mpath_info { * @NL80211_BAND_ATTR_HT_CAPA: HT capabilities, as in the HT information IE * @NL80211_BAND_ATTR_HT_AMPDU_FACTOR: A-MPDU factor, as in 11n * @NL80211_BAND_ATTR_HT_AMPDU_DENSITY: A-MPDU density, as in 11n + * @NL80211_BAND_ATTR_MAX: highest band attribute currently defined + * @__NL80211_BAND_ATTR_AFTER_LAST: internal use */ enum nl80211_band_attr { __NL80211_BAND_ATTR_INVALID, @@ -531,6 +1660,7 @@ enum nl80211_band_attr { /** * enum nl80211_frequency_attr - frequency attributes + * @__NL80211_FREQUENCY_ATTR_INVALID: attribute number 0 is reserved * @NL80211_FREQUENCY_ATTR_FREQ: Frequency in MHz * @NL80211_FREQUENCY_ATTR_DISABLED: Channel is disabled in current * regulatory domain. @@ -542,6 +1672,9 @@ enum nl80211_band_attr { * on this channel in current regulatory domain. * @NL80211_FREQUENCY_ATTR_MAX_TX_POWER: Maximum transmission power in mBm * (100 * dBm). + * @NL80211_FREQUENCY_ATTR_MAX: highest frequency attribute number + * currently defined + * @__NL80211_FREQUENCY_ATTR_AFTER_LAST: internal use */ enum nl80211_frequency_attr { __NL80211_FREQUENCY_ATTR_INVALID, @@ -561,9 +1694,13 @@ enum nl80211_frequency_attr { /** * enum nl80211_bitrate_attr - bitrate attributes + * @__NL80211_BITRATE_ATTR_INVALID: attribute number 0 is reserved * @NL80211_BITRATE_ATTR_RATE: Bitrate in units of 100 kbps * @NL80211_BITRATE_ATTR_2GHZ_SHORTPREAMBLE: Short preamble supported * in 2.4 GHz band. + * @NL80211_BITRATE_ATTR_MAX: highest bitrate attribute number + * currently defined + * @__NL80211_BITRATE_ATTR_AFTER_LAST: internal use */ enum nl80211_bitrate_attr { __NL80211_BITRATE_ATTR_INVALID, @@ -576,7 +1713,54 @@ enum nl80211_bitrate_attr { }; /** + * enum nl80211_initiator - Indicates the initiator of a reg domain request + * @NL80211_REGDOM_SET_BY_CORE: Core queried CRDA for a dynamic world + * regulatory domain. + * @NL80211_REGDOM_SET_BY_USER: User asked the wireless core to set the + * regulatory domain. + * @NL80211_REGDOM_SET_BY_DRIVER: a wireless drivers has hinted to the + * wireless core it thinks its knows the regulatory domain we should be in. + * @NL80211_REGDOM_SET_BY_COUNTRY_IE: the wireless core has received an + * 802.11 country information element with regulatory information it + * thinks we should consider. cfg80211 only processes the country + * code from the IE, and relies on the regulatory domain information + * structure passed by userspace (CRDA) from our wireless-regdb. + * If a channel is enabled but the country code indicates it should + * be disabled we disable the channel and re-enable it upon disassociation. + */ +enum nl80211_reg_initiator { + NL80211_REGDOM_SET_BY_CORE, + NL80211_REGDOM_SET_BY_USER, + NL80211_REGDOM_SET_BY_DRIVER, + NL80211_REGDOM_SET_BY_COUNTRY_IE, +}; + +/** + * enum nl80211_reg_type - specifies the type of regulatory domain + * @NL80211_REGDOM_TYPE_COUNTRY: the regulatory domain set is one that pertains + * to a specific country. When this is set you can count on the + * ISO / IEC 3166 alpha2 country code being valid. + * @NL80211_REGDOM_TYPE_WORLD: the regulatory set domain is the world regulatory + * domain. + * @NL80211_REGDOM_TYPE_CUSTOM_WORLD: the regulatory domain set is a custom + * driver specific world regulatory domain. These do not apply system-wide + * and are only applicable to the individual devices which have requested + * them to be applied. + * @NL80211_REGDOM_TYPE_INTERSECTION: the regulatory domain set is the product + * of an intersection between two regulatory domains -- the previously + * set regulatory domain on the system and the last accepted regulatory + * domain request to be processed. + */ +enum nl80211_reg_type { + NL80211_REGDOM_TYPE_COUNTRY, + NL80211_REGDOM_TYPE_WORLD, + NL80211_REGDOM_TYPE_CUSTOM_WORLD, + NL80211_REGDOM_TYPE_INTERSECTION, +}; + +/** * enum nl80211_reg_rule_attr - regulatory rule attributes + * @__NL80211_REG_RULE_ATTR_INVALID: attribute number 0 is reserved * @NL80211_ATTR_REG_RULE_FLAGS: a set of flags which specify additional * considerations for a given frequency range. These are the * &enum nl80211_reg_rule_flags. @@ -593,6 +1777,9 @@ enum nl80211_bitrate_attr { * If you don't have one then don't send this. * @NL80211_ATTR_POWER_RULE_MAX_EIRP: the maximum allowed EIRP for * a given frequency range. The value is in mBm (100 * dBm). + * @NL80211_REG_RULE_ATTR_MAX: highest regulatory rule attribute number + * currently defined + * @__NL80211_REG_RULE_ATTR_AFTER_LAST: internal use */ enum nl80211_reg_rule_attr { __NL80211_REG_RULE_ATTR_INVALID, @@ -611,6 +1798,26 @@ enum nl80211_reg_rule_attr { }; /** + * enum nl80211_sched_scan_match_attr - scheduled scan match attributes + * @__NL80211_SCHED_SCAN_MATCH_ATTR_INVALID: attribute number 0 is reserved + * @NL80211_SCHED_SCAN_MATCH_ATTR_SSID: SSID to be used for matching, + * only report BSS with matching SSID. + * @NL80211_SCHED_SCAN_MATCH_ATTR_MAX: highest scheduled scan filter + * attribute number currently defined + * @__NL80211_SCHED_SCAN_MATCH_ATTR_AFTER_LAST: internal use + */ +enum nl80211_sched_scan_match_attr { + __NL80211_SCHED_SCAN_MATCH_ATTR_INVALID, + + NL80211_ATTR_SCHED_SCAN_MATCH_SSID, + + /* keep last */ + __NL80211_SCHED_SCAN_MATCH_ATTR_AFTER_LAST, + NL80211_SCHED_SCAN_MATCH_ATTR_MAX = + __NL80211_SCHED_SCAN_MATCH_ATTR_AFTER_LAST - 1 +}; + +/** * enum nl80211_reg_rule_flags - regulatory rule flags * * @NL80211_RRF_NO_OFDM: OFDM modulation not allowed @@ -636,6 +1843,46 @@ enum nl80211_reg_rule_flags { }; /** + * enum nl80211_survey_info - survey information + * + * These attribute types are used with %NL80211_ATTR_SURVEY_INFO + * when getting information about a survey. + * + * @__NL80211_SURVEY_INFO_INVALID: attribute number 0 is reserved + * @NL80211_SURVEY_INFO_FREQUENCY: center frequency of channel + * @NL80211_SURVEY_INFO_NOISE: noise level of channel (u8, dBm) + * @NL80211_SURVEY_INFO_IN_USE: channel is currently being used + * @NL80211_SURVEY_INFO_CHANNEL_TIME: amount of time (in ms) that the radio + * spent on this channel + * @NL80211_SURVEY_INFO_CHANNEL_TIME_BUSY: amount of the time the primary + * channel was sensed busy (either due to activity or energy detect) + * @NL80211_SURVEY_INFO_CHANNEL_TIME_EXT_BUSY: amount of time the extension + * channel was sensed busy + * @NL80211_SURVEY_INFO_CHANNEL_TIME_RX: amount of time the radio spent + * receiving data + * @NL80211_SURVEY_INFO_CHANNEL_TIME_TX: amount of time the radio spent + * transmitting data + * @NL80211_SURVEY_INFO_MAX: highest survey info attribute number + * currently defined + * @__NL80211_SURVEY_INFO_AFTER_LAST: internal use + */ +enum nl80211_survey_info { + __NL80211_SURVEY_INFO_INVALID, + NL80211_SURVEY_INFO_FREQUENCY, + NL80211_SURVEY_INFO_NOISE, + NL80211_SURVEY_INFO_IN_USE, + NL80211_SURVEY_INFO_CHANNEL_TIME, + NL80211_SURVEY_INFO_CHANNEL_TIME_BUSY, + NL80211_SURVEY_INFO_CHANNEL_TIME_EXT_BUSY, + NL80211_SURVEY_INFO_CHANNEL_TIME_RX, + NL80211_SURVEY_INFO_CHANNEL_TIME_TX, + + /* keep last */ + __NL80211_SURVEY_INFO_AFTER_LAST, + NL80211_SURVEY_INFO_MAX = __NL80211_SURVEY_INFO_AFTER_LAST - 1 +}; + +/** * enum nl80211_mntr_flags - monitor configuration flags * * Monitor configuration flags. @@ -668,14 +1915,15 @@ enum nl80211_mntr_flags { /** * enum nl80211_meshconf_params - mesh configuration parameters * - * Mesh configuration parameters + * Mesh configuration parameters. These can be changed while the mesh is + * active. * * @__NL80211_MESHCONF_INVALID: internal use * * @NL80211_MESHCONF_RETRY_TIMEOUT: specifies the initial retry timeout in * millisecond units, used by the Peer Link Open message * - * @NL80211_MESHCONF_CONFIRM_TIMEOUT: specifies the inital confirm timeout, in + * @NL80211_MESHCONF_CONFIRM_TIMEOUT: specifies the initial confirm timeout, in * millisecond units, used by the peer link management to close a peer link * * @NL80211_MESHCONF_HOLDING_TIMEOUT: specifies the holding timeout, in @@ -715,6 +1963,18 @@ enum nl80211_mntr_flags { * @NL80211_MESHCONF_HWMP_NET_DIAM_TRVS_TIME: The interval of time (in TUs) * that it takes for an HWMP information element to propagate across the mesh * + * @NL80211_MESHCONF_HWMP_ROOTMODE: whether root mode is enabled or not + * + * @NL80211_MESHCONF_ELEMENT_TTL: specifies the value of TTL field set at a + * source mesh point for path selection elements. + * + * @NL80211_MESHCONF_HWMP_RANN_INTERVAL: The interval of time (in TUs) between + * root announcements are transmitted. + * + * @NL80211_MESHCONF_GATE_ANNOUNCEMENTS: Advertise that this mesh station has + * access to a broader network beyond the MBSS. This is done via Root + * Announcement frames. + * * @NL80211_MESHCONF_ATTR_MAX: highest possible mesh configuration attribute * * @__NL80211_MESHCONF_ATTR_AFTER_LAST: internal use @@ -734,6 +1994,10 @@ enum nl80211_meshconf_params { NL80211_MESHCONF_HWMP_ACTIVE_PATH_TIMEOUT, NL80211_MESHCONF_HWMP_PREQ_MIN_INTERVAL, NL80211_MESHCONF_HWMP_NET_DIAM_TRVS_TIME, + NL80211_MESHCONF_HWMP_ROOTMODE, + NL80211_MESHCONF_ELEMENT_TTL, + NL80211_MESHCONF_HWMP_RANN_INTERVAL, + NL80211_MESHCONF_GATE_ANNOUNCEMENTS, /* keep last */ __NL80211_MESHCONF_ATTR_AFTER_LAST, @@ -741,6 +2005,54 @@ enum nl80211_meshconf_params { }; /** + * enum nl80211_mesh_setup_params - mesh setup parameters + * + * Mesh setup parameters. These are used to start/join a mesh and cannot be + * changed while the mesh is active. + * + * @__NL80211_MESH_SETUP_INVALID: Internal use + * + * @NL80211_MESH_SETUP_ENABLE_VENDOR_PATH_SEL: Enable this option to use a + * vendor specific path selection algorithm or disable it to use the default + * HWMP. + * + * @NL80211_MESH_SETUP_ENABLE_VENDOR_METRIC: Enable this option to use a + * vendor specific path metric or disable it to use the default Airtime + * metric. + * + * @NL80211_MESH_SETUP_IE: Information elements for this mesh, for instance, a + * robust security network ie, or a vendor specific information element that + * vendors will use to identify the path selection methods and metrics in use. + * + * @NL80211_MESH_SETUP_USERSPACE_AUTH: Enable this option if an authentication + * daemon will be authenticating mesh candidates. + * + * @NL80211_MESH_SETUP_USERSPACE_AMPE: Enable this option if an authentication + * daemon will be securing peer link frames. AMPE is a secured version of Mesh + * Peering Management (MPM) and is implemented with the assistance of a + * userspace daemon. When this flag is set, the kernel will send peer + * management frames to a userspace daemon that will implement AMPE + * functionality (security capabilities selection, key confirmation, and key + * management). When the flag is unset (default), the kernel can autonomously + * complete (unsecured) mesh peering without the need of a userspace daemon. + * + * @NL80211_MESH_SETUP_ATTR_MAX: highest possible mesh setup attribute number + * @__NL80211_MESH_SETUP_ATTR_AFTER_LAST: Internal use + */ +enum nl80211_mesh_setup_params { + __NL80211_MESH_SETUP_INVALID, + NL80211_MESH_SETUP_ENABLE_VENDOR_PATH_SEL, + NL80211_MESH_SETUP_ENABLE_VENDOR_METRIC, + NL80211_MESH_SETUP_IE, + NL80211_MESH_SETUP_USERSPACE_AUTH, + NL80211_MESH_SETUP_USERSPACE_AMPE, + + /* keep last */ + __NL80211_MESH_SETUP_ATTR_AFTER_LAST, + NL80211_MESH_SETUP_ATTR_MAX = __NL80211_MESH_SETUP_ATTR_AFTER_LAST - 1 +}; + +/** * enum nl80211_txq_attr - TX queue parameter attributes * @__NL80211_TXQ_ATTR_INVALID: Attribute number 0 is reserved * @NL80211_TXQ_ATTR_QUEUE: TX queue identifier (NL80211_TXQ_Q_*) @@ -774,10 +2086,566 @@ enum nl80211_txq_q { NL80211_TXQ_Q_BK }; -enum nl80211_sec_chan_offset { - NL80211_SEC_CHAN_NO_HT /* No HT */, - NL80211_SEC_CHAN_DISABLED /* HT20 only */, - NL80211_SEC_CHAN_BELOW /* HT40- */, - NL80211_SEC_CHAN_ABOVE /* HT40+ */ +enum nl80211_channel_type { + NL80211_CHAN_NO_HT, + NL80211_CHAN_HT20, + NL80211_CHAN_HT40MINUS, + NL80211_CHAN_HT40PLUS }; + +/** + * enum nl80211_bss - netlink attributes for a BSS + * + * @__NL80211_BSS_INVALID: invalid + * @NL80211_BSS_BSSID: BSSID of the BSS (6 octets) + * @NL80211_BSS_FREQUENCY: frequency in MHz (u32) + * @NL80211_BSS_TSF: TSF of the received probe response/beacon (u64) + * @NL80211_BSS_BEACON_INTERVAL: beacon interval of the (I)BSS (u16) + * @NL80211_BSS_CAPABILITY: capability field (CPU order, u16) + * @NL80211_BSS_INFORMATION_ELEMENTS: binary attribute containing the + * raw information elements from the probe response/beacon (bin); + * if the %NL80211_BSS_BEACON_IES attribute is present, the IEs here are + * from a Probe Response frame; otherwise they are from a Beacon frame. + * However, if the driver does not indicate the source of the IEs, these + * IEs may be from either frame subtype. + * @NL80211_BSS_SIGNAL_MBM: signal strength of probe response/beacon + * in mBm (100 * dBm) (s32) + * @NL80211_BSS_SIGNAL_UNSPEC: signal strength of the probe response/beacon + * in unspecified units, scaled to 0..100 (u8) + * @NL80211_BSS_STATUS: status, if this BSS is "used" + * @NL80211_BSS_SEEN_MS_AGO: age of this BSS entry in ms + * @NL80211_BSS_BEACON_IES: binary attribute containing the raw information + * elements from a Beacon frame (bin); not present if no Beacon frame has + * yet been received + * @__NL80211_BSS_AFTER_LAST: internal + * @NL80211_BSS_MAX: highest BSS attribute + */ +enum nl80211_bss { + __NL80211_BSS_INVALID, + NL80211_BSS_BSSID, + NL80211_BSS_FREQUENCY, + NL80211_BSS_TSF, + NL80211_BSS_BEACON_INTERVAL, + NL80211_BSS_CAPABILITY, + NL80211_BSS_INFORMATION_ELEMENTS, + NL80211_BSS_SIGNAL_MBM, + NL80211_BSS_SIGNAL_UNSPEC, + NL80211_BSS_STATUS, + NL80211_BSS_SEEN_MS_AGO, + NL80211_BSS_BEACON_IES, + + /* keep last */ + __NL80211_BSS_AFTER_LAST, + NL80211_BSS_MAX = __NL80211_BSS_AFTER_LAST - 1 +}; + +/** + * enum nl80211_bss_status - BSS "status" + * @NL80211_BSS_STATUS_AUTHENTICATED: Authenticated with this BSS. + * @NL80211_BSS_STATUS_ASSOCIATED: Associated with this BSS. + * @NL80211_BSS_STATUS_IBSS_JOINED: Joined to this IBSS. + * + * The BSS status is a BSS attribute in scan dumps, which + * indicates the status the interface has wrt. this BSS. + */ +enum nl80211_bss_status { + NL80211_BSS_STATUS_AUTHENTICATED, + NL80211_BSS_STATUS_ASSOCIATED, + NL80211_BSS_STATUS_IBSS_JOINED, +}; + +/** + * enum nl80211_auth_type - AuthenticationType + * + * @NL80211_AUTHTYPE_OPEN_SYSTEM: Open System authentication + * @NL80211_AUTHTYPE_SHARED_KEY: Shared Key authentication (WEP only) + * @NL80211_AUTHTYPE_FT: Fast BSS Transition (IEEE 802.11r) + * @NL80211_AUTHTYPE_NETWORK_EAP: Network EAP (some Cisco APs and mainly LEAP) + * @__NL80211_AUTHTYPE_NUM: internal + * @NL80211_AUTHTYPE_MAX: maximum valid auth algorithm + * @NL80211_AUTHTYPE_AUTOMATIC: determine automatically (if necessary by + * trying multiple times); this is invalid in netlink -- leave out + * the attribute for this on CONNECT commands. + */ +enum nl80211_auth_type { + NL80211_AUTHTYPE_OPEN_SYSTEM, + NL80211_AUTHTYPE_SHARED_KEY, + NL80211_AUTHTYPE_FT, + NL80211_AUTHTYPE_NETWORK_EAP, + + /* keep last */ + __NL80211_AUTHTYPE_NUM, + NL80211_AUTHTYPE_MAX = __NL80211_AUTHTYPE_NUM - 1, + NL80211_AUTHTYPE_AUTOMATIC +}; + +/** + * enum nl80211_key_type - Key Type + * @NL80211_KEYTYPE_GROUP: Group (broadcast/multicast) key + * @NL80211_KEYTYPE_PAIRWISE: Pairwise (unicast/individual) key + * @NL80211_KEYTYPE_PEERKEY: PeerKey (DLS) + * @NUM_NL80211_KEYTYPES: number of defined key types + */ +enum nl80211_key_type { + NL80211_KEYTYPE_GROUP, + NL80211_KEYTYPE_PAIRWISE, + NL80211_KEYTYPE_PEERKEY, + + NUM_NL80211_KEYTYPES +}; + +/** + * enum nl80211_mfp - Management frame protection state + * @NL80211_MFP_NO: Management frame protection not used + * @NL80211_MFP_REQUIRED: Management frame protection required + */ +enum nl80211_mfp { + NL80211_MFP_NO, + NL80211_MFP_REQUIRED, +}; + +enum nl80211_wpa_versions { + NL80211_WPA_VERSION_1 = 1 << 0, + NL80211_WPA_VERSION_2 = 1 << 1, +}; + +/** + * enum nl80211_key_default_types - key default types + * @__NL80211_KEY_DEFAULT_TYPE_INVALID: invalid + * @NL80211_KEY_DEFAULT_TYPE_UNICAST: key should be used as default + * unicast key + * @NL80211_KEY_DEFAULT_TYPE_MULTICAST: key should be used as default + * multicast key + * @NUM_NL80211_KEY_DEFAULT_TYPES: number of default types + */ +enum nl80211_key_default_types { + __NL80211_KEY_DEFAULT_TYPE_INVALID, + NL80211_KEY_DEFAULT_TYPE_UNICAST, + NL80211_KEY_DEFAULT_TYPE_MULTICAST, + + NUM_NL80211_KEY_DEFAULT_TYPES +}; + +/** + * enum nl80211_key_attributes - key attributes + * @__NL80211_KEY_INVALID: invalid + * @NL80211_KEY_DATA: (temporal) key data; for TKIP this consists of + * 16 bytes encryption key followed by 8 bytes each for TX and RX MIC + * keys + * @NL80211_KEY_IDX: key ID (u8, 0-3) + * @NL80211_KEY_CIPHER: key cipher suite (u32, as defined by IEEE 802.11 + * section 7.3.2.25.1, e.g. 0x000FAC04) + * @NL80211_KEY_SEQ: transmit key sequence number (IV/PN) for TKIP and + * CCMP keys, each six bytes in little endian + * @NL80211_KEY_DEFAULT: flag indicating default key + * @NL80211_KEY_DEFAULT_MGMT: flag indicating default management key + * @NL80211_KEY_TYPE: the key type from enum nl80211_key_type, if not + * specified the default depends on whether a MAC address was + * given with the command using the key or not (u32) + * @NL80211_KEY_DEFAULT_TYPES: A nested attribute containing flags + * attributes, specifying what a key should be set as default as. + * See &enum nl80211_key_default_types. + * @__NL80211_KEY_AFTER_LAST: internal + * @NL80211_KEY_MAX: highest key attribute + */ +enum nl80211_key_attributes { + __NL80211_KEY_INVALID, + NL80211_KEY_DATA, + NL80211_KEY_IDX, + NL80211_KEY_CIPHER, + NL80211_KEY_SEQ, + NL80211_KEY_DEFAULT, + NL80211_KEY_DEFAULT_MGMT, + NL80211_KEY_TYPE, + NL80211_KEY_DEFAULT_TYPES, + + /* keep last */ + __NL80211_KEY_AFTER_LAST, + NL80211_KEY_MAX = __NL80211_KEY_AFTER_LAST - 1 +}; + +/** + * enum nl80211_tx_rate_attributes - TX rate set attributes + * @__NL80211_TXRATE_INVALID: invalid + * @NL80211_TXRATE_LEGACY: Legacy (non-MCS) rates allowed for TX rate selection + * in an array of rates as defined in IEEE 802.11 7.3.2.2 (u8 values with + * 1 = 500 kbps) but without the IE length restriction (at most + * %NL80211_MAX_SUPP_RATES in a single array). + * @__NL80211_TXRATE_AFTER_LAST: internal + * @NL80211_TXRATE_MAX: highest TX rate attribute + */ +enum nl80211_tx_rate_attributes { + __NL80211_TXRATE_INVALID, + NL80211_TXRATE_LEGACY, + + /* keep last */ + __NL80211_TXRATE_AFTER_LAST, + NL80211_TXRATE_MAX = __NL80211_TXRATE_AFTER_LAST - 1 +}; + +/** + * enum nl80211_band - Frequency band + * @NL80211_BAND_2GHZ: 2.4 GHz ISM band + * @NL80211_BAND_5GHZ: around 5 GHz band (4.9 - 5.7 GHz) + */ +enum nl80211_band { + NL80211_BAND_2GHZ, + NL80211_BAND_5GHZ, +}; + +enum nl80211_ps_state { + NL80211_PS_DISABLED, + NL80211_PS_ENABLED, +}; + +/** + * enum nl80211_attr_cqm - connection quality monitor attributes + * @__NL80211_ATTR_CQM_INVALID: invalid + * @NL80211_ATTR_CQM_RSSI_THOLD: RSSI threshold in dBm. This value specifies + * the threshold for the RSSI level at which an event will be sent. Zero + * to disable. + * @NL80211_ATTR_CQM_RSSI_HYST: RSSI hysteresis in dBm. This value specifies + * the minimum amount the RSSI level must change after an event before a + * new event may be issued (to reduce effects of RSSI oscillation). + * @NL80211_ATTR_CQM_RSSI_THRESHOLD_EVENT: RSSI threshold event + * @NL80211_ATTR_CQM_PKT_LOSS_EVENT: a u32 value indicating that this many + * consecutive packets were not acknowledged by the peer + * @__NL80211_ATTR_CQM_AFTER_LAST: internal + * @NL80211_ATTR_CQM_MAX: highest key attribute + */ +enum nl80211_attr_cqm { + __NL80211_ATTR_CQM_INVALID, + NL80211_ATTR_CQM_RSSI_THOLD, + NL80211_ATTR_CQM_RSSI_HYST, + NL80211_ATTR_CQM_RSSI_THRESHOLD_EVENT, + NL80211_ATTR_CQM_PKT_LOSS_EVENT, + + /* keep last */ + __NL80211_ATTR_CQM_AFTER_LAST, + NL80211_ATTR_CQM_MAX = __NL80211_ATTR_CQM_AFTER_LAST - 1 +}; + +/** + * enum nl80211_cqm_rssi_threshold_event - RSSI threshold event + * @NL80211_CQM_RSSI_THRESHOLD_EVENT_LOW: The RSSI level is lower than the + * configured threshold + * @NL80211_CQM_RSSI_THRESHOLD_EVENT_HIGH: The RSSI is higher than the + * configured threshold + */ +enum nl80211_cqm_rssi_threshold_event { + NL80211_CQM_RSSI_THRESHOLD_EVENT_LOW, + NL80211_CQM_RSSI_THRESHOLD_EVENT_HIGH, +}; + + +/** + * enum nl80211_tx_power_setting - TX power adjustment + * @NL80211_TX_POWER_AUTOMATIC: automatically determine transmit power + * @NL80211_TX_POWER_LIMITED: limit TX power by the mBm parameter + * @NL80211_TX_POWER_FIXED: fix TX power to the mBm parameter + */ +enum nl80211_tx_power_setting { + NL80211_TX_POWER_AUTOMATIC, + NL80211_TX_POWER_LIMITED, + NL80211_TX_POWER_FIXED, +}; + +/** + * enum nl80211_wowlan_packet_pattern_attr - WoWLAN packet pattern attribute + * @__NL80211_WOWLAN_PKTPAT_INVALID: invalid number for nested attribute + * @NL80211_WOWLAN_PKTPAT_PATTERN: the pattern, values where the mask has + * a zero bit are ignored + * @NL80211_WOWLAN_PKTPAT_MASK: pattern mask, must be long enough to have + * a bit for each byte in the pattern. The lowest-order bit corresponds + * to the first byte of the pattern, but the bytes of the pattern are + * in a little-endian-like format, i.e. the 9th byte of the pattern + * corresponds to the lowest-order bit in the second byte of the mask. + * For example: The match 00:xx:00:00:xx:00:00:00:00:xx:xx:xx (where + * xx indicates "don't care") would be represented by a pattern of + * twelve zero bytes, and a mask of "0xed,0x07". + * Note that the pattern matching is done as though frames were not + * 802.11 frames but 802.3 frames, i.e. the frame is fully unpacked + * first (including SNAP header unpacking) and then matched. + * @NUM_NL80211_WOWLAN_PKTPAT: number of attributes + * @MAX_NL80211_WOWLAN_PKTPAT: max attribute number + */ +enum nl80211_wowlan_packet_pattern_attr { + __NL80211_WOWLAN_PKTPAT_INVALID, + NL80211_WOWLAN_PKTPAT_MASK, + NL80211_WOWLAN_PKTPAT_PATTERN, + + NUM_NL80211_WOWLAN_PKTPAT, + MAX_NL80211_WOWLAN_PKTPAT = NUM_NL80211_WOWLAN_PKTPAT - 1, +}; + +/** + * struct nl80211_wowlan_pattern_support - pattern support information + * @max_patterns: maximum number of patterns supported + * @min_pattern_len: minimum length of each pattern + * @max_pattern_len: maximum length of each pattern + * + * This struct is carried in %NL80211_WOWLAN_TRIG_PKT_PATTERN when + * that is part of %NL80211_ATTR_WOWLAN_TRIGGERS_SUPPORTED in the + * capability information given by the kernel to userspace. + */ +struct nl80211_wowlan_pattern_support { + __u32 max_patterns; + __u32 min_pattern_len; + __u32 max_pattern_len; +} __attribute__((packed)); + +/** + * enum nl80211_wowlan_triggers - WoWLAN trigger definitions + * @__NL80211_WOWLAN_TRIG_INVALID: invalid number for nested attributes + * @NL80211_WOWLAN_TRIG_ANY: wake up on any activity, do not really put + * the chip into a special state -- works best with chips that have + * support for low-power operation already (flag) + * @NL80211_WOWLAN_TRIG_DISCONNECT: wake up on disconnect, the way disconnect + * is detected is implementation-specific (flag) + * @NL80211_WOWLAN_TRIG_MAGIC_PKT: wake up on magic packet (6x 0xff, followed + * by 16 repetitions of MAC addr, anywhere in payload) (flag) + * @NL80211_WOWLAN_TRIG_PKT_PATTERN: wake up on the specified packet patterns + * which are passed in an array of nested attributes, each nested attribute + * defining a with attributes from &struct nl80211_wowlan_trig_pkt_pattern. + * Each pattern defines a wakeup packet. The matching is done on the MSDU, + * i.e. as though the packet was an 802.3 packet, so the pattern matching + * is done after the packet is converted to the MSDU. + * + * In %NL80211_ATTR_WOWLAN_TRIGGERS_SUPPORTED, it is a binary attribute + * carrying a &struct nl80211_wowlan_pattern_support. + * @NL80211_WOWLAN_TRIG_GTK_REKEY_SUPPORTED: Not a real trigger, and cannot be + * used when setting, used only to indicate that GTK rekeying is supported + * by the device (flag) + * @NL80211_WOWLAN_TRIG_GTK_REKEY_FAILURE: wake up on GTK rekey failure (if + * done by the device) (flag) + * @NL80211_WOWLAN_TRIG_EAP_IDENT_REQUEST: wake up on EAP Identity Request + * packet (flag) + * @NL80211_WOWLAN_TRIG_4WAY_HANDSHAKE: wake up on 4-way handshake (flag) + * @NL80211_WOWLAN_TRIG_RFKILL_RELEASE: wake up when rfkill is released + * (on devices that have rfkill in the device) (flag) + * @NUM_NL80211_WOWLAN_TRIG: number of wake on wireless triggers + * @MAX_NL80211_WOWLAN_TRIG: highest wowlan trigger attribute number + */ +enum nl80211_wowlan_triggers { + __NL80211_WOWLAN_TRIG_INVALID, + NL80211_WOWLAN_TRIG_ANY, + NL80211_WOWLAN_TRIG_DISCONNECT, + NL80211_WOWLAN_TRIG_MAGIC_PKT, + NL80211_WOWLAN_TRIG_PKT_PATTERN, + NL80211_WOWLAN_TRIG_GTK_REKEY_SUPPORTED, + NL80211_WOWLAN_TRIG_GTK_REKEY_FAILURE, + NL80211_WOWLAN_TRIG_EAP_IDENT_REQUEST, + NL80211_WOWLAN_TRIG_4WAY_HANDSHAKE, + NL80211_WOWLAN_TRIG_RFKILL_RELEASE, + + /* keep last */ + NUM_NL80211_WOWLAN_TRIG, + MAX_NL80211_WOWLAN_TRIG = NUM_NL80211_WOWLAN_TRIG - 1 +}; + +/** + * enum nl80211_iface_limit_attrs - limit attributes + * @NL80211_IFACE_LIMIT_UNSPEC: (reserved) + * @NL80211_IFACE_LIMIT_MAX: maximum number of interfaces that + * can be chosen from this set of interface types (u32) + * @NL80211_IFACE_LIMIT_TYPES: nested attribute containing a + * flag attribute for each interface type in this set + * @NUM_NL80211_IFACE_LIMIT: number of attributes + * @MAX_NL80211_IFACE_LIMIT: highest attribute number + */ +enum nl80211_iface_limit_attrs { + NL80211_IFACE_LIMIT_UNSPEC, + NL80211_IFACE_LIMIT_MAX, + NL80211_IFACE_LIMIT_TYPES, + + /* keep last */ + NUM_NL80211_IFACE_LIMIT, + MAX_NL80211_IFACE_LIMIT = NUM_NL80211_IFACE_LIMIT - 1 +}; + +/** + * enum nl80211_if_combination_attrs -- interface combination attributes + * + * @NL80211_IFACE_COMB_UNSPEC: (reserved) + * @NL80211_IFACE_COMB_LIMITS: Nested attributes containing the limits + * for given interface types, see &enum nl80211_iface_limit_attrs. + * @NL80211_IFACE_COMB_MAXNUM: u32 attribute giving the total number of + * interfaces that can be created in this group. This number doesn't + * apply to interfaces purely managed in software, which are listed + * in a separate attribute %NL80211_ATTR_INTERFACES_SOFTWARE. + * @NL80211_IFACE_COMB_STA_AP_BI_MATCH: flag attribute specifying that + * beacon intervals within this group must be all the same even for + * infrastructure and AP/GO combinations, i.e. the GO(s) must adopt + * the infrastructure network's beacon interval. + * @NL80211_IFACE_COMB_NUM_CHANNELS: u32 attribute specifying how many + * different channels may be used within this group. + * @NUM_NL80211_IFACE_COMB: number of attributes + * @MAX_NL80211_IFACE_COMB: highest attribute number + * + * Examples: + * limits = [ #{STA} <= 1, #{AP} <= 1 ], matching BI, channels = 1, max = 2 + * => allows an AP and a STA that must match BIs + * + * numbers = [ #{AP, P2P-GO} <= 8 ], channels = 1, max = 8 + * => allows 8 of AP/GO + * + * numbers = [ #{STA} <= 2 ], channels = 2, max = 2 + * => allows two STAs on different channels + * + * numbers = [ #{STA} <= 1, #{P2P-client,P2P-GO} <= 3 ], max = 4 + * => allows a STA plus three P2P interfaces + * + * The list of these four possiblities could completely be contained + * within the %NL80211_ATTR_INTERFACE_COMBINATIONS attribute to indicate + * that any of these groups must match. + * + * "Combinations" of just a single interface will not be listed here, + * a single interface of any valid interface type is assumed to always + * be possible by itself. This means that implicitly, for each valid + * interface type, the following group always exists: + * numbers = [ #{} <= 1 ], channels = 1, max = 1 + */ +enum nl80211_if_combination_attrs { + NL80211_IFACE_COMB_UNSPEC, + NL80211_IFACE_COMB_LIMITS, + NL80211_IFACE_COMB_MAXNUM, + NL80211_IFACE_COMB_STA_AP_BI_MATCH, + NL80211_IFACE_COMB_NUM_CHANNELS, + + /* keep last */ + NUM_NL80211_IFACE_COMB, + MAX_NL80211_IFACE_COMB = NUM_NL80211_IFACE_COMB - 1 +}; + + +/** + * enum nl80211_plink_state - state of a mesh peer link finite state machine + * + * @NL80211_PLINK_LISTEN: initial state, considered the implicit + * state of non existant mesh peer links + * @NL80211_PLINK_OPN_SNT: mesh plink open frame has been sent to + * this mesh peer + * @NL80211_PLINK_OPN_RCVD: mesh plink open frame has been received + * from this mesh peer + * @NL80211_PLINK_CNF_RCVD: mesh plink confirm frame has been + * received from this mesh peer + * @NL80211_PLINK_ESTAB: mesh peer link is established + * @NL80211_PLINK_HOLDING: mesh peer link is being closed or cancelled + * @NL80211_PLINK_BLOCKED: all frames transmitted from this mesh + * plink are discarded + * @NUM_NL80211_PLINK_STATES: number of peer link states + * @MAX_NL80211_PLINK_STATES: highest numerical value of plink states + */ +enum nl80211_plink_state { + NL80211_PLINK_LISTEN, + NL80211_PLINK_OPN_SNT, + NL80211_PLINK_OPN_RCVD, + NL80211_PLINK_CNF_RCVD, + NL80211_PLINK_ESTAB, + NL80211_PLINK_HOLDING, + NL80211_PLINK_BLOCKED, + + /* keep last */ + NUM_NL80211_PLINK_STATES, + MAX_NL80211_PLINK_STATES = NUM_NL80211_PLINK_STATES - 1 +}; + +#define NL80211_KCK_LEN 16 +#define NL80211_KEK_LEN 16 +#define NL80211_REPLAY_CTR_LEN 8 + +/** + * enum nl80211_rekey_data - attributes for GTK rekey offload + * @__NL80211_REKEY_DATA_INVALID: invalid number for nested attributes + * @NL80211_REKEY_DATA_KEK: key encryption key (binary) + * @NL80211_REKEY_DATA_KCK: key confirmation key (binary) + * @NL80211_REKEY_DATA_REPLAY_CTR: replay counter (binary) + * @NUM_NL80211_REKEY_DATA: number of rekey attributes (internal) + * @MAX_NL80211_REKEY_DATA: highest rekey attribute (internal) + */ +enum nl80211_rekey_data { + __NL80211_REKEY_DATA_INVALID, + NL80211_REKEY_DATA_KEK, + NL80211_REKEY_DATA_KCK, + NL80211_REKEY_DATA_REPLAY_CTR, + + /* keep last */ + NUM_NL80211_REKEY_DATA, + MAX_NL80211_REKEY_DATA = NUM_NL80211_REKEY_DATA - 1 +}; + +/** + * enum nl80211_hidden_ssid - values for %NL80211_ATTR_HIDDEN_SSID + * @NL80211_HIDDEN_SSID_NOT_IN_USE: do not hide SSID (i.e., broadcast it in + * Beacon frames) + * @NL80211_HIDDEN_SSID_ZERO_LEN: hide SSID by using zero-length SSID element + * in Beacon frames + * @NL80211_HIDDEN_SSID_ZERO_CONTENTS: hide SSID by using correct length of SSID + * element in Beacon frames but zero out each byte in the SSID + */ +enum nl80211_hidden_ssid { + NL80211_HIDDEN_SSID_NOT_IN_USE, + NL80211_HIDDEN_SSID_ZERO_LEN, + NL80211_HIDDEN_SSID_ZERO_CONTENTS +}; + +/** + * enum nl80211_sta_wme_attr - station WME attributes + * @__NL80211_STA_WME_INVALID: invalid number for nested attribute + * @NL80211_STA_WME_UAPSD_QUEUES: bitmap of uapsd queues. the format + * is the same as the AC bitmap in the QoS info field. + * @NL80211_STA_WME_MAX_SP: max service period. the format is the same + * as the MAX_SP field in the QoS info field (but already shifted down). + * @__NL80211_STA_WME_AFTER_LAST: internal + * @NL80211_STA_WME_MAX: highest station WME attribute + */ +enum nl80211_sta_wme_attr { + __NL80211_STA_WME_INVALID, + NL80211_STA_WME_UAPSD_QUEUES, + NL80211_STA_WME_MAX_SP, + + /* keep last */ + __NL80211_STA_WME_AFTER_LAST, + NL80211_STA_WME_MAX = __NL80211_STA_WME_AFTER_LAST - 1 +}; + +/** + * enum nl80211_pmksa_candidate_attr - attributes for PMKSA caching candidates + * @__NL80211_PMKSA_CANDIDATE_INVALID: invalid number for nested attributes + * @NL80211_PMKSA_CANDIDATE_INDEX: candidate index (u32; the smaller, the higher + * priority) + * @NL80211_PMKSA_CANDIDATE_BSSID: candidate BSSID (6 octets) + * @NL80211_PMKSA_CANDIDATE_PREAUTH: RSN pre-authentication supported (flag) + * @NUM_NL80211_PMKSA_CANDIDATE: number of PMKSA caching candidate attributes + * (internal) + * @MAX_NL80211_PMKSA_CANDIDATE: highest PMKSA caching candidate attribute + * (internal) + */ +enum nl80211_pmksa_candidate_attr { + __NL80211_PMKSA_CANDIDATE_INVALID, + NL80211_PMKSA_CANDIDATE_INDEX, + NL80211_PMKSA_CANDIDATE_BSSID, + NL80211_PMKSA_CANDIDATE_PREAUTH, + + /* keep last */ + NUM_NL80211_PMKSA_CANDIDATE, + MAX_NL80211_PMKSA_CANDIDATE = NUM_NL80211_PMKSA_CANDIDATE - 1 +}; + +/** + * enum nl80211_tdls_operation - values for %NL80211_ATTR_TDLS_OPERATION + * @NL80211_TDLS_DISCOVERY_REQ: Send a TDLS discovery request + * @NL80211_TDLS_SETUP: Setup TDLS link + * @NL80211_TDLS_TEARDOWN: Teardown a TDLS link which is already established + * @NL80211_TDLS_ENABLE_LINK: Enable TDLS link + * @NL80211_TDLS_DISABLE_LINK: Disable TDLS link + */ +enum nl80211_tdls_operation { + NL80211_TDLS_DISCOVERY_REQ, + NL80211_TDLS_SETUP, + NL80211_TDLS_TEARDOWN, + NL80211_TDLS_ENABLE_LINK, + NL80211_TDLS_DISABLE_LINK, +}; + #endif /* __LINUX_NL80211_H */ -- 2.7.4