From f7c32e8ece7fefd950382a7522aff9939a218b91 Mon Sep 17 00:00:00 2001 From: Stefan Roese Date: Wed, 27 Apr 2016 09:10:42 +0200 Subject: [PATCH] arm: spear: x600: Add support for Micrel KSZ9031 PHY As the old ethernet PHY is not available any more, the x600 board has been redesigned with the Micrel KSZ9031 PHY. This patch adds support to autodetect the PHY and configure the Micrel PHY correctly. Signed-off-by: Stefan Roese --- board/spear/x600/x600.c | 80 ++++++++++++++++++++++++++++++++++++------------- include/configs/x600.h | 2 ++ 2 files changed, 61 insertions(+), 21 deletions(-) diff --git a/board/spear/x600/x600.c b/board/spear/x600/x600.c index b8edfcd..f8e9fdd 100644 --- a/board/spear/x600/x600.c +++ b/board/spear/x600/x600.c @@ -8,6 +8,7 @@ */ #include +#include #include #include #include @@ -69,27 +70,64 @@ void board_nand_init(void) int board_phy_config(struct phy_device *phydev) { - /* Extended PHY control 1, select GMII */ - phy_write(phydev, MDIO_DEVAD_NONE, 23, 0x0020); - - /* Software reset necessary after GMII mode selction */ - phy_reset(phydev); - - /* Enable extended page register access */ - phy_write(phydev, MDIO_DEVAD_NONE, 31, 0x0001); - - /* 17e: Enhanced LED behavior, needs to be written twice */ - phy_write(phydev, MDIO_DEVAD_NONE, 17, 0x09ff); - phy_write(phydev, MDIO_DEVAD_NONE, 17, 0x09ff); - - /* 16e: Enhanced LED method select */ - phy_write(phydev, MDIO_DEVAD_NONE, 16, 0xe0ea); - - /* Disable extended page register access */ - phy_write(phydev, MDIO_DEVAD_NONE, 31, 0x0000); - - /* Enable clock output pin */ - phy_write(phydev, MDIO_DEVAD_NONE, 18, 0x0049); + unsigned short id1, id2; + + /* check whether KSZ9031 or AR8035 has to be configured */ + id1 = phy_read(phydev, MDIO_DEVAD_NONE, 2); + id2 = phy_read(phydev, MDIO_DEVAD_NONE, 3); + + if ((id1 == 0x22) && ((id2 & 0xFFF0) == 0x1620)) { + /* PHY configuration for Micrel KSZ9031 */ + printf("PHY KSZ9031 detected - "); + + phy_write(phydev, MDIO_DEVAD_NONE, MII_CTRL1000, 0x1c00); + + /* control data pad skew - devaddr = 0x02, register = 0x04 */ + ksz9031_phy_extended_write(phydev, 0x02, + MII_KSZ9031_EXT_RGMII_CTRL_SIG_SKEW, + MII_KSZ9031_MOD_DATA_NO_POST_INC, + 0x0000); + /* rx data pad skew - devaddr = 0x02, register = 0x05 */ + ksz9031_phy_extended_write(phydev, 0x02, + MII_KSZ9031_EXT_RGMII_RX_DATA_SKEW, + MII_KSZ9031_MOD_DATA_NO_POST_INC, + 0x0000); + /* tx data pad skew - devaddr = 0x02, register = 0x05 */ + ksz9031_phy_extended_write(phydev, 0x02, + MII_KSZ9031_EXT_RGMII_TX_DATA_SKEW, + MII_KSZ9031_MOD_DATA_NO_POST_INC, + 0x0000); + /* gtx and rx clock pad skew - devaddr = 0x02, reg = 0x08 */ + ksz9031_phy_extended_write(phydev, 0x02, + MII_KSZ9031_EXT_RGMII_CLOCK_SKEW, + MII_KSZ9031_MOD_DATA_NO_POST_INC, + 0x03FF); + } else { + /* PHY configuration for Vitesse VSC8641 */ + printf("PHY VSC8641 detected - "); + + /* Extended PHY control 1, select GMII */ + phy_write(phydev, MDIO_DEVAD_NONE, 23, 0x0020); + + /* Software reset necessary after GMII mode selction */ + phy_reset(phydev); + + /* Enable extended page register access */ + phy_write(phydev, MDIO_DEVAD_NONE, 31, 0x0001); + + /* 17e: Enhanced LED behavior, needs to be written twice */ + phy_write(phydev, MDIO_DEVAD_NONE, 17, 0x09ff); + phy_write(phydev, MDIO_DEVAD_NONE, 17, 0x09ff); + + /* 16e: Enhanced LED method select */ + phy_write(phydev, MDIO_DEVAD_NONE, 16, 0xe0ea); + + /* Disable extended page register access */ + phy_write(phydev, MDIO_DEVAD_NONE, 31, 0x0000); + + /* Enable clock output pin */ + phy_write(phydev, MDIO_DEVAD_NONE, 18, 0x0049); + } if (phydev->drv->config) phydev->drv->config(phydev); diff --git a/include/configs/x600.h b/include/configs/x600.h index 5fdd2be..07c8abe 100644 --- a/include/configs/x600.h +++ b/include/configs/x600.h @@ -80,6 +80,8 @@ #define CONFIG_PHY_RESET_DELAY 10000 /* in usec */ #define CONFIG_PHY_ADDR 0 /* PHY address */ #define CONFIG_PHY_GIGE /* Include GbE speed/duplex detection */ +#define CONFIG_PHY_MICREL +#define CONFIG_PHY_MICREL_KSZ9031 #define CONFIG_SPEAR_GPIO -- 2.7.4