From f10aa369d5c2ccfc734e158c0a802009953e8c68 Mon Sep 17 00:00:00 2001 From: Boris Brezillon Date: Thu, 6 Dec 2018 11:41:17 +0100 Subject: [PATCH] mtd: spi-nor: Avoid forward declaration of internal functions Reorganize the code to kill forward declarations of spi_nor_match_id() macronix_quad_enable() and spi_nor_hwcaps_read2cmd(). Signed-off-by: Boris Brezillon Reviewed-by: Tudor Ambarus --- drivers/mtd/spi-nor/spi-nor.c | 616 +++++++++++++++++++++--------------------- 1 file changed, 305 insertions(+), 311 deletions(-) diff --git a/drivers/mtd/spi-nor/spi-nor.c b/drivers/mtd/spi-nor/spi-nor.c index 0a3c610..81270cb 100644 --- a/drivers/mtd/spi-nor/spi-nor.c +++ b/drivers/mtd/spi-nor/spi-nor.c @@ -289,8 +289,6 @@ struct flash_info { #define JEDEC_MFR(info) ((info)->id[0]) -static const struct flash_info *spi_nor_match_id(const char *name); - /* * Read the status register, returning its value in the location * Return the status register value. @@ -1395,7 +1393,247 @@ static int spi_nor_is_locked(struct mtd_info *mtd, loff_t ofs, uint64_t len) return ret; } -static int macronix_quad_enable(struct spi_nor *nor); +/* + * Write status Register and configuration register with 2 bytes + * The first byte will be written to the status register, while the + * second byte will be written to the configuration register. + * Return negative if error occurred. + */ +static int write_sr_cr(struct spi_nor *nor, u8 *sr_cr) +{ + int ret; + + write_enable(nor); + + ret = nor->write_reg(nor, SPINOR_OP_WRSR, sr_cr, 2); + if (ret < 0) { + dev_err(nor->dev, + "error while writing configuration register\n"); + return -EINVAL; + } + + ret = spi_nor_wait_till_ready(nor); + if (ret) { + dev_err(nor->dev, + "timeout while writing configuration register\n"); + return ret; + } + + return 0; +} + +/** + * macronix_quad_enable() - set QE bit in Status Register. + * @nor: pointer to a 'struct spi_nor' + * + * Set the Quad Enable (QE) bit in the Status Register. + * + * bit 6 of the Status Register is the QE bit for Macronix like QSPI memories. + * + * Return: 0 on success, -errno otherwise. + */ +static int macronix_quad_enable(struct spi_nor *nor) +{ + int ret, val; + + val = read_sr(nor); + if (val < 0) + return val; + if (val & SR_QUAD_EN_MX) + return 0; + + write_enable(nor); + + write_sr(nor, val | SR_QUAD_EN_MX); + + ret = spi_nor_wait_till_ready(nor); + if (ret) + return ret; + + ret = read_sr(nor); + if (!(ret > 0 && (ret & SR_QUAD_EN_MX))) { + dev_err(nor->dev, "Macronix Quad bit not set\n"); + return -EINVAL; + } + + return 0; +} + +/** + * spansion_quad_enable() - set QE bit in Configuraiton Register. + * @nor: pointer to a 'struct spi_nor' + * + * Set the Quad Enable (QE) bit in the Configuration Register. + * This function is kept for legacy purpose because it has been used for a + * long time without anybody complaining but it should be considered as + * deprecated and maybe buggy. + * First, this function doesn't care about the previous values of the Status + * and Configuration Registers when it sets the QE bit (bit 1) in the + * Configuration Register: all other bits are cleared, which may have unwanted + * side effects like removing some block protections. + * Secondly, it uses the Read Configuration Register (35h) instruction though + * some very old and few memories don't support this instruction. If a pull-up + * resistor is present on the MISO/IO1 line, we might still be able to pass the + * "read back" test because the QSPI memory doesn't recognize the command, + * so leaves the MISO/IO1 line state unchanged, hence read_cr() returns 0xFF. + * + * bit 1 of the Configuration Register is the QE bit for Spansion like QSPI + * memories. + * + * Return: 0 on success, -errno otherwise. + */ +static int spansion_quad_enable(struct spi_nor *nor) +{ + u8 sr_cr[2] = {0, CR_QUAD_EN_SPAN}; + int ret; + + ret = write_sr_cr(nor, sr_cr); + if (ret) + return ret; + + /* read back and check it */ + ret = read_cr(nor); + if (!(ret > 0 && (ret & CR_QUAD_EN_SPAN))) { + dev_err(nor->dev, "Spansion Quad bit not set\n"); + return -EINVAL; + } + + return 0; +} + +/** + * spansion_no_read_cr_quad_enable() - set QE bit in Configuration Register. + * @nor: pointer to a 'struct spi_nor' + * + * Set the Quad Enable (QE) bit in the Configuration Register. + * This function should be used with QSPI memories not supporting the Read + * Configuration Register (35h) instruction. + * + * bit 1 of the Configuration Register is the QE bit for Spansion like QSPI + * memories. + * + * Return: 0 on success, -errno otherwise. + */ +static int spansion_no_read_cr_quad_enable(struct spi_nor *nor) +{ + u8 sr_cr[2]; + int ret; + + /* Keep the current value of the Status Register. */ + ret = read_sr(nor); + if (ret < 0) { + dev_err(nor->dev, "error while reading status register\n"); + return -EINVAL; + } + sr_cr[0] = ret; + sr_cr[1] = CR_QUAD_EN_SPAN; + + return write_sr_cr(nor, sr_cr); +} + +/** + * spansion_read_cr_quad_enable() - set QE bit in Configuration Register. + * @nor: pointer to a 'struct spi_nor' + * + * Set the Quad Enable (QE) bit in the Configuration Register. + * This function should be used with QSPI memories supporting the Read + * Configuration Register (35h) instruction. + * + * bit 1 of the Configuration Register is the QE bit for Spansion like QSPI + * memories. + * + * Return: 0 on success, -errno otherwise. + */ +static int spansion_read_cr_quad_enable(struct spi_nor *nor) +{ + struct device *dev = nor->dev; + u8 sr_cr[2]; + int ret; + + /* Check current Quad Enable bit value. */ + ret = read_cr(nor); + if (ret < 0) { + dev_err(dev, "error while reading configuration register\n"); + return -EINVAL; + } + + if (ret & CR_QUAD_EN_SPAN) + return 0; + + sr_cr[1] = ret | CR_QUAD_EN_SPAN; + + /* Keep the current value of the Status Register. */ + ret = read_sr(nor); + if (ret < 0) { + dev_err(dev, "error while reading status register\n"); + return -EINVAL; + } + sr_cr[0] = ret; + + ret = write_sr_cr(nor, sr_cr); + if (ret) + return ret; + + /* Read back and check it. */ + ret = read_cr(nor); + if (!(ret > 0 && (ret & CR_QUAD_EN_SPAN))) { + dev_err(nor->dev, "Spansion Quad bit not set\n"); + return -EINVAL; + } + + return 0; +} + +/** + * sr2_bit7_quad_enable() - set QE bit in Status Register 2. + * @nor: pointer to a 'struct spi_nor' + * + * Set the Quad Enable (QE) bit in the Status Register 2. + * + * This is one of the procedures to set the QE bit described in the SFDP + * (JESD216 rev B) specification but no manufacturer using this procedure has + * been identified yet, hence the name of the function. + * + * Return: 0 on success, -errno otherwise. + */ +static int sr2_bit7_quad_enable(struct spi_nor *nor) +{ + u8 sr2; + int ret; + + /* Check current Quad Enable bit value. */ + ret = nor->read_reg(nor, SPINOR_OP_RDSR2, &sr2, 1); + if (ret) + return ret; + if (sr2 & SR2_QUAD_EN_BIT7) + return 0; + + /* Update the Quad Enable bit. */ + sr2 |= SR2_QUAD_EN_BIT7; + + write_enable(nor); + + ret = nor->write_reg(nor, SPINOR_OP_WRSR2, &sr2, 1); + if (ret < 0) { + dev_err(nor->dev, "error while writing status register 2\n"); + return -EINVAL; + } + + ret = spi_nor_wait_till_ready(nor); + if (ret < 0) { + dev_err(nor->dev, "timeout while writing status register 2\n"); + return ret; + } + + /* Read back and check it. */ + ret = nor->read_reg(nor, SPINOR_OP_RDSR2, &sr2, 1); + if (!(ret > 0 && (sr2 & SR2_QUAD_EN_BIT7))) { + dev_err(nor->dev, "SR2 Quad bit not set\n"); + return -EINVAL; + } + + return 0; +} /* Used when the "_ext_id" is two bytes at most */ #define INFO(_jedec_id, _ext_id, _sector_size, _n_sectors, _flags) \ @@ -2002,249 +2240,7 @@ write_err: return ret; } -/** - * macronix_quad_enable() - set QE bit in Status Register. - * @nor: pointer to a 'struct spi_nor' - * - * Set the Quad Enable (QE) bit in the Status Register. - * - * bit 6 of the Status Register is the QE bit for Macronix like QSPI memories. - * - * Return: 0 on success, -errno otherwise. - */ -static int macronix_quad_enable(struct spi_nor *nor) -{ - int ret, val; - - val = read_sr(nor); - if (val < 0) - return val; - if (val & SR_QUAD_EN_MX) - return 0; - - write_enable(nor); - - write_sr(nor, val | SR_QUAD_EN_MX); - - ret = spi_nor_wait_till_ready(nor); - if (ret) - return ret; - - ret = read_sr(nor); - if (!(ret > 0 && (ret & SR_QUAD_EN_MX))) { - dev_err(nor->dev, "Macronix Quad bit not set\n"); - return -EINVAL; - } - - return 0; -} - -/* - * Write status Register and configuration register with 2 bytes - * The first byte will be written to the status register, while the - * second byte will be written to the configuration register. - * Return negative if error occurred. - */ -static int write_sr_cr(struct spi_nor *nor, u8 *sr_cr) -{ - int ret; - - write_enable(nor); - - ret = nor->write_reg(nor, SPINOR_OP_WRSR, sr_cr, 2); - if (ret < 0) { - dev_err(nor->dev, - "error while writing configuration register\n"); - return -EINVAL; - } - - ret = spi_nor_wait_till_ready(nor); - if (ret) { - dev_err(nor->dev, - "timeout while writing configuration register\n"); - return ret; - } - - return 0; -} - -/** - * spansion_quad_enable() - set QE bit in Configuraiton Register. - * @nor: pointer to a 'struct spi_nor' - * - * Set the Quad Enable (QE) bit in the Configuration Register. - * This function is kept for legacy purpose because it has been used for a - * long time without anybody complaining but it should be considered as - * deprecated and maybe buggy. - * First, this function doesn't care about the previous values of the Status - * and Configuration Registers when it sets the QE bit (bit 1) in the - * Configuration Register: all other bits are cleared, which may have unwanted - * side effects like removing some block protections. - * Secondly, it uses the Read Configuration Register (35h) instruction though - * some very old and few memories don't support this instruction. If a pull-up - * resistor is present on the MISO/IO1 line, we might still be able to pass the - * "read back" test because the QSPI memory doesn't recognize the command, - * so leaves the MISO/IO1 line state unchanged, hence read_cr() returns 0xFF. - * - * bit 1 of the Configuration Register is the QE bit for Spansion like QSPI - * memories. - * - * Return: 0 on success, -errno otherwise. - */ -static int spansion_quad_enable(struct spi_nor *nor) -{ - u8 sr_cr[2] = {0, CR_QUAD_EN_SPAN}; - int ret; - - ret = write_sr_cr(nor, sr_cr); - if (ret) - return ret; - - /* read back and check it */ - ret = read_cr(nor); - if (!(ret > 0 && (ret & CR_QUAD_EN_SPAN))) { - dev_err(nor->dev, "Spansion Quad bit not set\n"); - return -EINVAL; - } - - return 0; -} - -/** - * spansion_no_read_cr_quad_enable() - set QE bit in Configuration Register. - * @nor: pointer to a 'struct spi_nor' - * - * Set the Quad Enable (QE) bit in the Configuration Register. - * This function should be used with QSPI memories not supporting the Read - * Configuration Register (35h) instruction. - * - * bit 1 of the Configuration Register is the QE bit for Spansion like QSPI - * memories. - * - * Return: 0 on success, -errno otherwise. - */ -static int spansion_no_read_cr_quad_enable(struct spi_nor *nor) -{ - u8 sr_cr[2]; - int ret; - - /* Keep the current value of the Status Register. */ - ret = read_sr(nor); - if (ret < 0) { - dev_err(nor->dev, "error while reading status register\n"); - return -EINVAL; - } - sr_cr[0] = ret; - sr_cr[1] = CR_QUAD_EN_SPAN; - - return write_sr_cr(nor, sr_cr); -} - -/** - * spansion_read_cr_quad_enable() - set QE bit in Configuration Register. - * @nor: pointer to a 'struct spi_nor' - * - * Set the Quad Enable (QE) bit in the Configuration Register. - * This function should be used with QSPI memories supporting the Read - * Configuration Register (35h) instruction. - * - * bit 1 of the Configuration Register is the QE bit for Spansion like QSPI - * memories. - * - * Return: 0 on success, -errno otherwise. - */ -static int spansion_read_cr_quad_enable(struct spi_nor *nor) -{ - struct device *dev = nor->dev; - u8 sr_cr[2]; - int ret; - - /* Check current Quad Enable bit value. */ - ret = read_cr(nor); - if (ret < 0) { - dev_err(dev, "error while reading configuration register\n"); - return -EINVAL; - } - - if (ret & CR_QUAD_EN_SPAN) - return 0; - - sr_cr[1] = ret | CR_QUAD_EN_SPAN; - - /* Keep the current value of the Status Register. */ - ret = read_sr(nor); - if (ret < 0) { - dev_err(dev, "error while reading status register\n"); - return -EINVAL; - } - sr_cr[0] = ret; - - ret = write_sr_cr(nor, sr_cr); - if (ret) - return ret; - - /* Read back and check it. */ - ret = read_cr(nor); - if (!(ret > 0 && (ret & CR_QUAD_EN_SPAN))) { - dev_err(nor->dev, "Spansion Quad bit not set\n"); - return -EINVAL; - } - - return 0; -} - -/** - * sr2_bit7_quad_enable() - set QE bit in Status Register 2. - * @nor: pointer to a 'struct spi_nor' - * - * Set the Quad Enable (QE) bit in the Status Register 2. - * - * This is one of the procedures to set the QE bit described in the SFDP - * (JESD216 rev B) specification but no manufacturer using this procedure has - * been identified yet, hence the name of the function. - * - * Return: 0 on success, -errno otherwise. - */ -static int sr2_bit7_quad_enable(struct spi_nor *nor) -{ - u8 sr2; - int ret; - - /* Check current Quad Enable bit value. */ - ret = nor->read_reg(nor, SPINOR_OP_RDSR2, &sr2, 1); - if (ret) - return ret; - if (sr2 & SR2_QUAD_EN_BIT7) - return 0; - - /* Update the Quad Enable bit. */ - sr2 |= SR2_QUAD_EN_BIT7; - - write_enable(nor); - - ret = nor->write_reg(nor, SPINOR_OP_WRSR2, &sr2, 1); - if (ret < 0) { - dev_err(nor->dev, "error while writing status register 2\n"); - return -EINVAL; - } - - ret = spi_nor_wait_till_ready(nor); - if (ret < 0) { - dev_err(nor->dev, "timeout while writing status register 2\n"); - return ret; - } - - /* Read back and check it. */ - ret = nor->read_reg(nor, SPINOR_OP_RDSR2, &sr2, 1); - if (!(ret > 0 && (sr2 & SR2_QUAD_EN_BIT7))) { - dev_err(nor->dev, "SR2 Quad bit not set\n"); - return -EINVAL; - } - - return 0; -} - -static int spi_nor_check(struct spi_nor *nor) +static int spi_nor_check(struct spi_nor *nor) { if (!nor->dev || !nor->read || !nor->write || !nor->read_reg || !nor->write_reg) { @@ -2318,6 +2314,57 @@ spi_nor_set_pp_settings(struct spi_nor_pp_command *pp, pp->proto = proto; } +static int spi_nor_hwcaps2cmd(u32 hwcaps, const int table[][2], size_t size) +{ + size_t i; + + for (i = 0; i < size; i++) + if (table[i][0] == (int)hwcaps) + return table[i][1]; + + return -EINVAL; +} + +static int spi_nor_hwcaps_read2cmd(u32 hwcaps) +{ + static const int hwcaps_read2cmd[][2] = { + { SNOR_HWCAPS_READ, SNOR_CMD_READ }, + { SNOR_HWCAPS_READ_FAST, SNOR_CMD_READ_FAST }, + { SNOR_HWCAPS_READ_1_1_1_DTR, SNOR_CMD_READ_1_1_1_DTR }, + { SNOR_HWCAPS_READ_1_1_2, SNOR_CMD_READ_1_1_2 }, + { SNOR_HWCAPS_READ_1_2_2, SNOR_CMD_READ_1_2_2 }, + { SNOR_HWCAPS_READ_2_2_2, SNOR_CMD_READ_2_2_2 }, + { SNOR_HWCAPS_READ_1_2_2_DTR, SNOR_CMD_READ_1_2_2_DTR }, + { SNOR_HWCAPS_READ_1_1_4, SNOR_CMD_READ_1_1_4 }, + { SNOR_HWCAPS_READ_1_4_4, SNOR_CMD_READ_1_4_4 }, + { SNOR_HWCAPS_READ_4_4_4, SNOR_CMD_READ_4_4_4 }, + { SNOR_HWCAPS_READ_1_4_4_DTR, SNOR_CMD_READ_1_4_4_DTR }, + { SNOR_HWCAPS_READ_1_1_8, SNOR_CMD_READ_1_1_8 }, + { SNOR_HWCAPS_READ_1_8_8, SNOR_CMD_READ_1_8_8 }, + { SNOR_HWCAPS_READ_8_8_8, SNOR_CMD_READ_8_8_8 }, + { SNOR_HWCAPS_READ_1_8_8_DTR, SNOR_CMD_READ_1_8_8_DTR }, + }; + + return spi_nor_hwcaps2cmd(hwcaps, hwcaps_read2cmd, + ARRAY_SIZE(hwcaps_read2cmd)); +} + +static int spi_nor_hwcaps_pp2cmd(u32 hwcaps) +{ + static const int hwcaps_pp2cmd[][2] = { + { SNOR_HWCAPS_PP, SNOR_CMD_PP }, + { SNOR_HWCAPS_PP_1_1_4, SNOR_CMD_PP_1_1_4 }, + { SNOR_HWCAPS_PP_1_4_4, SNOR_CMD_PP_1_4_4 }, + { SNOR_HWCAPS_PP_4_4_4, SNOR_CMD_PP_4_4_4 }, + { SNOR_HWCAPS_PP_1_1_8, SNOR_CMD_PP_1_1_8 }, + { SNOR_HWCAPS_PP_1_8_8, SNOR_CMD_PP_1_8_8 }, + { SNOR_HWCAPS_PP_8_8_8, SNOR_CMD_PP_8_8_8 }, + }; + + return spi_nor_hwcaps2cmd(hwcaps, hwcaps_pp2cmd, + ARRAY_SIZE(hwcaps_pp2cmd)); +} + /* * Serial Flash Discoverable Parameters (SFDP) parsing. */ @@ -2527,8 +2574,6 @@ static const struct sfdp_bfpt_erase sfdp_bfpt_erases[] = { {BFPT_DWORD(9), 16}, }; -static int spi_nor_hwcaps_read2cmd(u32 hwcaps); - /** * spi_nor_set_erase_type() - set a SPI NOR erase type * @erase: pointer to a structure that describes a SPI NOR erase type @@ -3435,57 +3480,6 @@ static int spi_nor_init_params(struct spi_nor *nor, return 0; } -static int spi_nor_hwcaps2cmd(u32 hwcaps, const int table[][2], size_t size) -{ - size_t i; - - for (i = 0; i < size; i++) - if (table[i][0] == (int)hwcaps) - return table[i][1]; - - return -EINVAL; -} - -static int spi_nor_hwcaps_read2cmd(u32 hwcaps) -{ - static const int hwcaps_read2cmd[][2] = { - { SNOR_HWCAPS_READ, SNOR_CMD_READ }, - { SNOR_HWCAPS_READ_FAST, SNOR_CMD_READ_FAST }, - { SNOR_HWCAPS_READ_1_1_1_DTR, SNOR_CMD_READ_1_1_1_DTR }, - { SNOR_HWCAPS_READ_1_1_2, SNOR_CMD_READ_1_1_2 }, - { SNOR_HWCAPS_READ_1_2_2, SNOR_CMD_READ_1_2_2 }, - { SNOR_HWCAPS_READ_2_2_2, SNOR_CMD_READ_2_2_2 }, - { SNOR_HWCAPS_READ_1_2_2_DTR, SNOR_CMD_READ_1_2_2_DTR }, - { SNOR_HWCAPS_READ_1_1_4, SNOR_CMD_READ_1_1_4 }, - { SNOR_HWCAPS_READ_1_4_4, SNOR_CMD_READ_1_4_4 }, - { SNOR_HWCAPS_READ_4_4_4, SNOR_CMD_READ_4_4_4 }, - { SNOR_HWCAPS_READ_1_4_4_DTR, SNOR_CMD_READ_1_4_4_DTR }, - { SNOR_HWCAPS_READ_1_1_8, SNOR_CMD_READ_1_1_8 }, - { SNOR_HWCAPS_READ_1_8_8, SNOR_CMD_READ_1_8_8 }, - { SNOR_HWCAPS_READ_8_8_8, SNOR_CMD_READ_8_8_8 }, - { SNOR_HWCAPS_READ_1_8_8_DTR, SNOR_CMD_READ_1_8_8_DTR }, - }; - - return spi_nor_hwcaps2cmd(hwcaps, hwcaps_read2cmd, - ARRAY_SIZE(hwcaps_read2cmd)); -} - -static int spi_nor_hwcaps_pp2cmd(u32 hwcaps) -{ - static const int hwcaps_pp2cmd[][2] = { - { SNOR_HWCAPS_PP, SNOR_CMD_PP }, - { SNOR_HWCAPS_PP_1_1_4, SNOR_CMD_PP_1_1_4 }, - { SNOR_HWCAPS_PP_1_4_4, SNOR_CMD_PP_1_4_4 }, - { SNOR_HWCAPS_PP_4_4_4, SNOR_CMD_PP_4_4_4 }, - { SNOR_HWCAPS_PP_1_1_8, SNOR_CMD_PP_1_1_8 }, - { SNOR_HWCAPS_PP_1_8_8, SNOR_CMD_PP_1_8_8 }, - { SNOR_HWCAPS_PP_8_8_8, SNOR_CMD_PP_8_8_8 }, - }; - - return spi_nor_hwcaps2cmd(hwcaps, hwcaps_pp2cmd, - ARRAY_SIZE(hwcaps_pp2cmd)); -} - static int spi_nor_select_read(struct spi_nor *nor, const struct spi_nor_flash_parameter *params, u32 shared_hwcaps) @@ -3762,6 +3756,18 @@ void spi_nor_restore(struct spi_nor *nor) } EXPORT_SYMBOL_GPL(spi_nor_restore); +static const struct flash_info *spi_nor_match_id(const char *name) +{ + const struct flash_info *id = spi_nor_ids; + + while (id->name) { + if (!strcmp(name, id->name)) + return id; + id++; + } + return NULL; +} + int spi_nor_scan(struct spi_nor *nor, const char *name, const struct spi_nor_hwcaps *hwcaps) { @@ -3965,18 +3971,6 @@ int spi_nor_scan(struct spi_nor *nor, const char *name, } EXPORT_SYMBOL_GPL(spi_nor_scan); -static const struct flash_info *spi_nor_match_id(const char *name) -{ - const struct flash_info *id = spi_nor_ids; - - while (id->name) { - if (!strcmp(name, id->name)) - return id; - id++; - } - return NULL; -} - MODULE_LICENSE("GPL"); MODULE_AUTHOR("Huang Shijie "); MODULE_AUTHOR("Mike Lavender"); -- 2.7.4