From e373cdbe50b5ce636e4d0893a5a1b761c7a4a452 Mon Sep 17 00:00:00 2001 From: Dave Stevenson Date: Mon, 5 Dec 2022 17:33:28 +0000 Subject: [PATCH] drm/bridge: Document the expected behaviour of DSI host controllers The exact behaviour of DSI host controllers is not specified, therefore define it. Signed-off-by: Dave Stevenson Reviewed-by: Laurent Pinchart Link: https://lore.kernel.org/r/20221205173328.1395350-7-dave.stevenson@raspberrypi.com Signed-off-by: Maxime Ripard --- Documentation/gpu/drm-kms-helpers.rst | 7 +++++ drivers/gpu/drm/drm_bridge.c | 39 +++++++++++++++++++++++++++ 2 files changed, 46 insertions(+) diff --git a/Documentation/gpu/drm-kms-helpers.rst b/Documentation/gpu/drm-kms-helpers.rst index a4860ffd6e86..b8ab05e42dbb 100644 --- a/Documentation/gpu/drm-kms-helpers.rst +++ b/Documentation/gpu/drm-kms-helpers.rst @@ -188,6 +188,13 @@ Bridge Helper Reference .. kernel-doc:: drivers/gpu/drm/drm_bridge.c :export: +MIPI-DSI bridge operation +------------------------- + +.. kernel-doc:: drivers/gpu/drm/drm_bridge.c + :doc: dsi bridge operations + + Bridge Connector Helper Reference --------------------------------- diff --git a/drivers/gpu/drm/drm_bridge.c b/drivers/gpu/drm/drm_bridge.c index 5f40c83b1b42..c3d69af02e79 100644 --- a/drivers/gpu/drm/drm_bridge.c +++ b/drivers/gpu/drm/drm_bridge.c @@ -153,6 +153,45 @@ * situation when probing. */ +/** + * DOC: dsi bridge operations + * + * DSI host interfaces are expected to be implemented as bridges rather than + * encoders, however there are a few aspects of their operation that need to + * be defined in order to provide a consistent interface. + * + * A DSI host should keep the PHY powered down until the pre_enable operation is + * called. All lanes are in an undefined idle state up to this point, and it + * must not be assumed that it is LP-11. + * pre_enable should initialise the PHY, set the data lanes to LP-11, and the + * clock lane to either LP-11 or HS depending on the mode_flag + * %MIPI_DSI_CLOCK_NON_CONTINUOUS. + * + * Ordinarily the downstream bridge DSI peripheral pre_enable will have been + * called before the DSI host. If the DSI peripheral requires LP-11 and/or + * the clock lane to be in HS mode prior to pre_enable, then it can set the + * &pre_enable_prev_first flag to request the pre_enable (and + * post_disable) order to be altered to enable the DSI host first. + * + * Either the CRTC being enabled, or the DSI host enable operation should switch + * the host to actively transmitting video on the data lanes. + * + * The reverse also applies. The DSI host disable operation or stopping the CRTC + * should stop transmitting video, and the data lanes should return to the LP-11 + * state. The DSI host &post_disable operation should disable the PHY. + * If the &pre_enable_prev_first flag is set, then the DSI peripheral's + * bridge &post_disable will be called before the DSI host's post_disable. + * + * Whilst it is valid to call &host_transfer prior to pre_enable or after + * post_disable, the exact state of the lanes is undefined at this point. The + * DSI host should initialise the interface, transmit the data, and then disable + * the interface again. + * + * Ultra Low Power State (ULPS) is not explicitly supported by DRM. If + * implemented, it therefore needs to be handled entirely within the DSI Host + * driver. + */ + static DEFINE_MUTEX(bridge_lock); static LIST_HEAD(bridge_list); -- 2.34.1