From c57c7980ffe6e04a99b5f401a663426d7144f392 Mon Sep 17 00:00:00 2001 From: Stefan Roese Date: Thu, 11 Aug 2005 17:56:56 +0200 Subject: [PATCH] Add NAND FLASH support for AMCC Bamboo 440EP eval board Patch by Stefan Roese, 11 Aug 2005 --- CHANGELOG | 3 + board/amcc/bamboo/bamboo.c | 122 ++++++++++++++++++++++++++++++++------- board/amcc/bamboo/flash.c | 11 +++- board/amcc/bamboo/init.S | 24 +++++--- cpu/ppc4xx/440gx_enet.c | 8 +-- include/configs/bamboo.h | 138 +++++++++++++++++++++++++++++++++++---------- 6 files changed, 242 insertions(+), 64 deletions(-) diff --git a/CHANGELOG b/CHANGELOG index beff987..62d8a09 100644 --- a/CHANGELOG +++ b/CHANGELOG @@ -2,6 +2,9 @@ Changes for U-Boot 1.1.3: ====================================================================== +* Add NAND FLASH support for AMCC Bamboo 440EP eval board + Patch by Stefan Roese, 11 Aug 2005 + * Fix CompactFlash problem on HMI1001 board * Make new "mtdparts" code build with older compilers diff --git a/board/amcc/bamboo/bamboo.c b/board/amcc/bamboo/bamboo.c index 0d5ab71..d02add5 100644 --- a/board/amcc/bamboo/bamboo.c +++ b/board/amcc/bamboo/bamboo.c @@ -29,6 +29,7 @@ void ext_bus_cntlr_init(void); void configure_ppc440ep_pins(void); +int is_nand_selected(void); gpio_param_s gpio_tab[GPIO_GROUP_MAX][GPIO_MAX]; #if 0 @@ -132,10 +133,10 @@ gpio_param_s gpio_tab[GPIO_GROUP_MAX][GPIO_MAX]; EBC0_BNCR_BW_8BIT #define EBC0_BNCR_SMALL_FLASH_CS4 \ - EBC0_BNCR_BAS_ENCODE(0x87800000) | \ - EBC0_BNCR_BS_8MB | \ + EBC0_BNCR_BAS_ENCODE(0x87F00000) | \ + EBC0_BNCR_BS_1MB | \ EBC0_BNCR_BU_RW | \ - EBC0_BNCR_BW_16BIT + EBC0_BNCR_BW_8BIT /* Large Flash or SRAM */ #define EBC0_BNAP_LARGE_FLASH_OR_SRAM \ @@ -273,6 +274,87 @@ int board_early_init_f(void) return 0; } +#if (CONFIG_COMMANDS & CFG_CMD_NAND) +#include +extern struct nand_chip nand_dev_desc[CFG_MAX_NAND_DEVICE]; + +/*----------------------------------------------------------------------------+ + | nand_reset. + | Reset Nand flash + | This routine will abort previous cmd + +----------------------------------------------------------------------------*/ +int nand_reset(ulong addr) +{ + int wait=0, stat=0; + + out8(addr + NAND_CMD_REG, NAND0_CMD_RESET); + out8(addr + NAND_CMD_REG, NAND0_CMD_READ_STATUS); + + while ((stat != 0xc0) && (wait != 0xffff)) { + stat = in8(addr + NAND_DATA_REG); + wait++; + } + + if (stat == 0xc0) { + return 0; + } else { + printf("NAND Reset timeout.\n"); + return -1; + } +} + +void board_nand_set_device(int cs, ulong addr) +{ + /* Set NandFlash Core Configuration Register */ + out32(addr + NAND_CCR_REG, 0x00001000 | (cs << 24)); + + switch (cs) { + case 1: + /* ------- + * NAND0 + * ------- + * K9F1208U0A : 4 addr cyc, 1 col + 3 Row + * Set NDF1CR - Enable External CS1 in NAND FLASH controller + */ + out32(addr + NAND_CR1_REG, 0x80002222); + break; + + case 2: + /* ------- + * NAND1 + * ------- + * K9K2G0B : 5 addr cyc, 2 col + 3 Row + * Set NDF2CR : Enable External CS2 in NAND FLASH controller + */ + out32(addr + NAND_CR2_REG, 0xC0007777); + break; + } + + /* Perform Reset Command */ + if (nand_reset(addr) != 0) + return; +} + +void nand_init(void) +{ + board_nand_set_device(1, CFG_NAND_ADDR); + + nand_probe(CFG_NAND_ADDR); + if (nand_dev_desc[0].ChipID != NAND_ChipID_UNKNOWN) { + print_size(nand_dev_desc[0].totlen, "\n"); + } + +#if 0 /* NAND1 not supported yet */ + board_nand_set_device(2, CFG_NAND2_ADDR); + + nand_probe(CFG_NAND2_ADDR); + if (nand_dev_desc[0].ChipID != NAND_ChipID_UNKNOWN) { + print_size(nand_dev_desc[0].totlen, "\n"); + } +#endif +} +#endif /* (CONFIG_COMMANDS & CFG_CMD_NAND) */ + int checkboard(void) { sys_info_t sysinfo; @@ -585,7 +667,11 @@ int is_powerpc440ep_pass1(void) +----------------------------------------------------------------------------*/ int is_nand_selected(void) { - return FALSE; /* test-only */ +#ifdef CONFIG_BAMBOO_NAND + return TRUE; +#else + return FALSE; +#endif } /*----------------------------------------------------------------------------+ @@ -829,12 +915,8 @@ void ext_bus_cntlr_init(void) /* NAND Flash */ ebc0_cs1_bnap_value = EBC0_BNAP_NAND_FLASH; ebc0_cs1_bncr_value = EBC0_BNCR_NAND_FLASH_CS1; - /*ebc0_cs2_bnap_value = EBC0_BNAP_NAND_FLASH; - ebc0_cs2_bncr_value = EBC0_BNCR_NAND_FLASH_CS2; - ebc0_cs3_bnap_value = EBC0_BNAP_NAND_FLASH; - ebc0_cs3_bncr_value = EBC0_BNCR_NAND_FLASH_CS3;*/ - ebc0_cs2_bnap_value = 0; - ebc0_cs2_bncr_value = 0; + ebc0_cs2_bnap_value = EBC0_BNAP_NAND_FLASH; + ebc0_cs2_bncr_value = EBC0_BNCR_NAND_FLASH_CS2; ebc0_cs3_bnap_value = 0; ebc0_cs3_bncr_value = 0; } else { @@ -985,7 +1067,7 @@ void ext_bus_cntlr_init(void) +----------------------------------------------------------------------------*/ uart_config_nb_t get_uart_configuration(void) { - return (L4); /* test-only */ + return (L4); } /*----------------------------------------------------------------------------+ @@ -1132,8 +1214,7 @@ void ndfc_selection_in_fpga(void) fpga_selection_1_reg = in8(FPGA_SELECTION_1_REG) &~FPGA_SEL_1_REG_NF_SELEC_MASK; fpga_selection_1_reg |= FPGA_SEL_1_REG_NF0_SEL_BY_NFCS1; - /*fpga_selection_1_reg |= FPGA_SEL_1_REG_NF1_SEL_BY_NFCS2; */ - /*fpga_selection_1_reg |= FPGA_SEL_1_REG_NF1_SEL_BY_NFCS3; */ + fpga_selection_1_reg |= FPGA_SEL_1_REG_NF1_SEL_BY_NFCS2; out8(FPGA_SELECTION_1_REG,fpga_selection_1_reg); } @@ -1725,11 +1806,15 @@ void force_bup_core_selection(core_selection_t *core_select_P, config_validity_t *(core_select_P+UIC_0_3) = CORE_SELECTED; *(core_select_P+UIC_4_9) = CORE_SELECTED; - *(core_select_P+SCP_CORE) = CORE_SELECTED; - *(core_select_P+DMA_CHANNEL_CD) = CORE_SELECTED; - *(core_select_P+PACKET_REJ_FUNC_AVAIL) = CORE_SELECTED; + *(core_select_P+SCP_CORE) = CORE_SELECTED; + *(core_select_P+DMA_CHANNEL_CD) = CORE_SELECTED; + *(core_select_P+PACKET_REJ_FUNC_AVAIL) = CORE_SELECTED; *(core_select_P+USB1_DEVICE) = CORE_SELECTED; + if (is_nand_selected()) { + *(core_select_P+NAND_FLASH) = CORE_SELECTED; + } + *config_val_P = CONFIG_IS_VALID; } @@ -1901,9 +1986,8 @@ void configure_ppc440ep_pins(void) SDR0_CUST0_NDFC_ENABLE | SDR0_CUST0_NDFC_BW_8_BIT | SDR0_CUST0_NDFC_ARE_MASK | - SDR0_CUST0_CHIPSELGAT_EN1 ); - /*SDR0_CUST0_CHIPSELGAT_EN2 ); */ - /*SDR0_CUST0_CHIPSELGAT_EN3 ); */ + SDR0_CUST0_CHIPSELGAT_EN1 | + SDR0_CUST0_CHIPSELGAT_EN2); ndfc_selection_in_fpga(); } diff --git a/board/amcc/bamboo/flash.c b/board/amcc/bamboo/flash.c index 97a4b98..a30ab7a 100644 --- a/board/amcc/bamboo/flash.c +++ b/board/amcc/bamboo/flash.c @@ -50,15 +50,16 @@ flash_info_t flash_info[CFG_MAX_FLASH_BANKS]; /* info for FLASH chips */ /* * Mark big flash bank (16 bit instead of 8 bit access) in address with bit 0 */ -static unsigned long flash_addr_table[8][CFG_MAX_FLASH_BANKS] = { +static unsigned long flash_addr_table[][CFG_MAX_FLASH_BANKS] = { {0x87800001, 0xFFF00000, 0xFFF80000}, /* 0:boot from small flash */ {0x00000000, 0x00000000, 0x00000000}, /* 1:boot from pci 66 */ {0x00000000, 0x00000000, 0x00000000}, /* 2:boot from nand flash */ - {0x87800000, 0x87880000, 0xFF800001}, /* 3:boot from big flash 33*/ - {0x87800000, 0x87880000, 0xFF800001}, /* 4:boot from big flash 66*/ + {0x87F00000, 0x87F80000, 0xFFC00001}, /* 3:boot from big flash 33*/ + {0x87F00000, 0x87F80000, 0xFFC00001}, /* 4:boot from big flash 66*/ {0x00000000, 0x00000000, 0x00000000}, /* 5:boot from */ {0x00000000, 0x00000000, 0x00000000}, /* 6:boot from pci 66 */ {0x00000000, 0x00000000, 0x00000000}, /* 7:boot from */ + {0x87C00001, 0xFFF00000, 0xFFF80000}, /* 0:boot from small flash */ }; /* @@ -117,6 +118,10 @@ unsigned long flash_init(void) index = 2; break; } + } else if (index == 0) { + if (in8(FPGA_SETTING_REG) & FPGA_SET_REG_OP_CODE_FLASH_ABOVE) { + index = 8; /* sram below op code flash -> new index 8 */ + } } DEBUGF("\n"); diff --git a/board/amcc/bamboo/init.S b/board/amcc/bamboo/init.S index 9070293..7820107 100644 --- a/board/amcc/bamboo/init.S +++ b/board/amcc/bamboo/init.S @@ -86,14 +86,20 @@ tlbtab: tlbtab_start - /* - 0xf0000000 must be first, before relocation SA_I must be off to use the - dcache as stack. It is patched after relocation to enable SA_I - */ - tlbentry( 0xf0000000, SZ_256M, 0xf0000000, 0, AC_R|AC_W|AC_X|SA_G/*|SA_I*/) - tlbentry( CFG_SDRAM_BASE, SZ_256M, 0x00000000, 0, AC_R|AC_W|AC_X|SA_G|SA_I ) - tlbentry( CFG_PCI_BASE, SZ_256M, 0xE0000000, 0, AC_R|AC_W|SA_G|SA_I ) - tlbentry( CFG_NVRAM_BASE_ADDR, SZ_256M, 0x80000000, 0, AC_R|AC_W|AC_X|SA_W|SA_I ) + + /* + * BOOT_CS (FLASH) must be first. Before relocation SA_I can be off to use the + * speed up boot process. It is patched after relocation to enable SA_I + */ + tlbentry( CFG_BOOT_BASE_ADDR, SZ_256M, CFG_BOOT_BASE_ADDR, 0, AC_R|AC_W|AC_X|SA_G/*|SA_I*/) + + /* TLB-entry for init-ram in dcache (SA_I must be turned off!) */ + tlbentry( CFG_INIT_RAM_ADDR, SZ_64K, CFG_INIT_RAM_ADDR, 0, AC_R|AC_W|AC_X|SA_G ) + + tlbentry( CFG_SDRAM_BASE, SZ_256M, CFG_SDRAM_BASE, 0, AC_R|AC_W|AC_X|SA_G|SA_I ) + tlbentry( CFG_PCI_BASE, SZ_256M, CFG_PCI_BASE, 0, AC_R|AC_W|SA_G|SA_I ) + tlbentry( CFG_NVRAM_BASE_ADDR, SZ_256M, CFG_NVRAM_BASE_ADDR, 0, AC_R|AC_W|AC_X|SA_W|SA_I ) + tlbentry( CFG_NAND_ADDR, SZ_256M, CFG_NAND_ADDR, 0, AC_R|AC_W|AC_X|SA_W|SA_I ) /* PCI */ tlbentry( CFG_PCI_MEMBASE, SZ_256M, CFG_PCI_MEMBASE, 0, AC_R|AC_W|SA_G|SA_I ) @@ -102,6 +108,6 @@ tlbtab: tlbentry( CFG_PCI_MEMBASE3, SZ_256M, CFG_PCI_MEMBASE3, 0, AC_R|AC_W|SA_G|SA_I ) /* USB 2.0 Device */ - tlbentry( CFG_USB_DEVICE, SZ_1K, 0x50000000, 0, AC_R|AC_W|SA_G|SA_I ) + tlbentry( CFG_USB_DEVICE, SZ_1K, CFG_USB_DEVICE, 0, AC_R|AC_W|SA_G|SA_I ) tlbtab_end diff --git a/cpu/ppc4xx/440gx_enet.c b/cpu/ppc4xx/440gx_enet.c index 63227fa..68cbf34 100644 --- a/cpu/ppc4xx/440gx_enet.c +++ b/cpu/ppc4xx/440gx_enet.c @@ -375,8 +375,8 @@ static int ppc_440x_eth_init (struct eth_device *dev, bd_t * bis) out32 (RGMII_FER, ((RGMII_FER_RGMII << RGMII_FER_V (2)) | (RGMII_FER_RGMII << RGMII_FER_V (3)))); } - #endif + out32 (ZMII_SSR, ZMII_SSR_SP << ZMII_SSR_V(devnum)); __asm__ volatile ("eieio"); @@ -521,13 +521,13 @@ static int ppc_440x_eth_init (struct eth_device *dev, bd_t * bis) } mtsdr(sdr_mfr, reg); #endif + /* Set ZMII/RGMII speed according to the phy link speed */ reg = in32 (ZMII_SSR); if ( (speed == 100) || (speed == 1000) ) out32 (ZMII_SSR, reg | (ZMII_SSR_SP << ZMII_SSR_V (devnum))); else - out32 (ZMII_SSR, - reg & (~(ZMII_SSR_SP << ZMII_SSR_V (devnum)))); + out32 (ZMII_SSR, reg & (~(ZMII_SSR_SP << ZMII_SSR_V (devnum)))); if ((devnum == 2) || (devnum == 3)) { if (speed == 1000) @@ -672,7 +672,7 @@ static int ppc_440x_eth_init (struct eth_device *dev, bd_t * bis) /* set RX buffer size */ mtdcr (malrcbs3, ENET_MAX_MTU_ALIGNED / 16); break; -#endif /*CONFIG_440GX */ +#endif /* CONFIG_440GX */ case 0: default: /* setup MAL tx & rx channel pointers */ diff --git a/include/configs/bamboo.h b/include/configs/bamboo.h index 88bbadf..64ea6be 100644 --- a/include/configs/bamboo.h +++ b/include/configs/bamboo.h @@ -32,11 +32,18 @@ *----------------------------------------------------------------------*/ #define CONFIG_BAMBOO 1 /* Board is BAMBOO */ #define CONFIG_440EP 1 /* Specific PPC440EP support */ - #define CONFIG_4xx 1 /* ... PPC4xx family */ -#define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_early_init_f */ #define CONFIG_SYS_CLK_FREQ 33333333 /* external freq to pll */ +#define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_early_init_f */ + +/* + * Please note that, if NAND support is enabled, the 2nd ethernet port + * can't be used because of pin multiplexing. So, if you want to use the + * 2nd ethernet port you have to "undef" the following define. + */ +#define CONFIG_BAMBOO_NAND 1 /* enable nand flash support */ + /*----------------------------------------------------------------------- * Base addresses -- Note these are effective addresses where the * actual resources get mapped (not physical addresses) @@ -58,13 +65,15 @@ #define CFG_USB_DEVICE 0x50000000 #define CFG_NVRAM_BASE_ADDR 0x80000000 -#define CFG_BCSR_BASE (CFG_NVRAM_BASE_ADDR | 0x2000) +#define CFG_BOOT_BASE_ADDR 0xf0000000 +#define CFG_NAND_ADDR 0x90000000 +#define CFG_NAND2_ADDR 0x94000000 /*----------------------------------------------------------------------- * Initial RAM & stack pointer (placed in SDRAM) *----------------------------------------------------------------------*/ -#define CFG_INIT_RAM_ADDR 0xf0000000 /* DCache */ -#define CFG_INIT_RAM_END 0x1000 +#define CFG_INIT_RAM_ADDR 0x70000000 /* DCache */ +#define CFG_INIT_RAM_END (8 << 10) #define CFG_GBL_DATA_SIZE 256 /* num bytes initial data */ #define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE) #define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET @@ -88,7 +97,7 @@ * The DS1558 code assumes this condition * *----------------------------------------------------------------------*/ -#define CFG_NVRAM_SIZE (0x2000 - 0x10) /* NVRAM size(8k)- RTC regs */ +#define CFG_NVRAM_SIZE (0x2000 - 0x10) /* NVRAM size(8k)- RTC regs */ #define CONFIG_RTC_DS1556 1 /* DS1556 RTC */ /*----------------------------------------------------------------------- @@ -118,22 +127,81 @@ #define CFG_FLASH_ADDR1 0x2aa #define CFG_FLASH_WORD_SIZE unsigned char -#define CFG_FLASH_2ND_16BIT_DEV 1 /* bamboo has 8 and 16bit device */ -#define CFG_FLASH_2ND_ADDR 0x87800000 /* bamboo has 8 and 16bit device */ +#define CFG_FLASH_2ND_16BIT_DEV 1 /* bamboo has 8 and 16bit device */ +#define CFG_FLASH_2ND_ADDR 0x87800000 /* bamboo has 8 and 16bit device */ #ifdef CFG_ENV_IS_IN_FLASH #define CFG_ENV_SECT_SIZE 0x10000 /* size of one complete sector */ #define CFG_ENV_ADDR (CFG_MONITOR_BASE-CFG_ENV_SECT_SIZE) -#define CFG_ENV_SIZE 0x4000 /* Total Size of Environment Sector */ +#define CFG_ENV_SIZE 0x2000 /* Total Size of Environment Sector */ -#if 0 /* test-only */ /* Address and size of Redundant Environment Sector */ #define CFG_ENV_ADDR_REDUND (CFG_ENV_ADDR-CFG_ENV_SECT_SIZE) #define CFG_ENV_SIZE_REDUND (CFG_ENV_SIZE) -#endif #endif /* CFG_ENV_IS_IN_FLASH */ /*----------------------------------------------------------------------- + * NAND-FLASH related + *----------------------------------------------------------------------*/ +#define NAND_CMD_REG (0x00) /* NandFlash Command Register */ +#define NAND_ADDR_REG (0x04) /* NandFlash Address Register */ +#define NAND_DATA_REG (0x08) /* NandFlash Data Register */ +#define NAND_ECC0_REG (0x10) /* NandFlash ECC Register0 */ +#define NAND_ECC1_REG (0x14) /* NandFlash ECC Register1 */ +#define NAND_ECC2_REG (0x18) /* NandFlash ECC Register2 */ +#define NAND_ECC3_REG (0x1C) /* NandFlash ECC Register3 */ +#define NAND_ECC4_REG (0x20) /* NandFlash ECC Register4 */ +#define NAND_ECC5_REG (0x24) /* NandFlash ECC Register5 */ +#define NAND_ECC6_REG (0x28) /* NandFlash ECC Register6 */ +#define NAND_ECC7_REG (0x2C) /* NandFlash ECC Register7 */ +#define NAND_CR0_REG (0x30) /* NandFlash Device Bank0 Config Register */ +#define NAND_CR1_REG (0x34) /* NandFlash Device Bank1 Config Register */ +#define NAND_CR2_REG (0x38) /* NandFlash Device Bank2 Config Register */ +#define NAND_CR3_REG (0x3C) /* NandFlash Device Bank3 Config Register */ +#define NAND_CCR_REG (0x40) /* NandFlash Core Configuration Register */ +#define NAND_STAT_REG (0x44) /* NandFlash Device Status Register */ +#define NAND_HWCTL_REG (0x48) /* NandFlash Direct Hwd Control Register */ +#define NAND_REVID_REG (0x50) /* NandFlash Core Revision Id Register */ + +/* Nand Flash K9F1208U0A Command Set => Nand Flash 0 */ +#define NAND0_CMD_READ1_HALF1 0x00 /* Starting addr for 1rst half of registers */ +#define NAND0_CMD_READ1_HALF2 0x01 /* Starting addr for 2nd half of registers */ +#define NAND0_CMD_READ2 0x50 +#define NAND0_CMD_READ_ID 0x90 +#define NAND0_CMD_READ_STATUS 0x70 +#define NAND0_CMD_RESET 0xFF +#define NAND0_CMD_PAGE_PROG 0x80 +#define NAND0_CMD_PAGE_PROG_TRUE 0x10 +#define NAND0_CMD_PAGE_PROG_DUMMY 0x11 +#define NAND0_CMD_BLOCK_ERASE 0x60 +#define NAND0_CMD_BLOCK_ERASE_END 0xD0 + +#define CFG_MAX_NAND_DEVICE 1 /* Max number of NAND devices */ +#define SECTORSIZE 512 + +#define ADDR_COLUMN 1 +#define ADDR_PAGE 2 +#define ADDR_COLUMN_PAGE 3 + +#define NAND_ChipID_UNKNOWN 0x00 +#define NAND_MAX_FLOORS 1 +#define NAND_MAX_CHIPS 1 + +#define WRITE_NAND_COMMAND(d, adr) do {*(volatile u8 *)((ulong)adr+NAND_CMD_REG) = d;} while(0) +#define WRITE_NAND_ADDRESS(d, adr) do {*(volatile u8 *)((ulong)adr+NAND_ADDR_REG) = d;} while(0) +#define WRITE_NAND(d, adr) do {*(volatile u8 *)((ulong)adr+NAND_DATA_REG) = d;} while(0) +#define READ_NAND(adr) (*(volatile u8 *)((ulong)adr+NAND_DATA_REG)) +#define NAND_WAIT_READY(nand) while (!(*(volatile u8 *)((ulong)nand->IO_ADDR+NAND_STAT_REG) & 0x01)) + +/* not needed with 440EP NAND controller */ +#define NAND_CTL_CLRALE(nandptr) +#define NAND_CTL_SETALE(nandptr) +#define NAND_CTL_CLRCLE(nandptr) +#define NAND_CTL_SETCLE(nandptr) +#define NAND_DISABLE_CE(nand) +#define NAND_ENABLE_CE(nand) + +/*----------------------------------------------------------------------- * DDR SDRAM *----------------------------------------------------------------------------- */ #define CONFIG_SPD_EEPROM /* Use SPD EEPROM for setup */ @@ -206,10 +274,14 @@ #define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ #define CONFIG_MII 1 /* MII PHY management */ -#define CONFIG_NET_MULTI 1 /* required for netconsole */ #define CONFIG_PHY_ADDR 0 /* PHY address, See schematics */ + +#ifndef CONFIG_BAMBOO_NAND +#define CONFIG_NET_MULTI 1 /* required for netconsole */ #define CONFIG_PHY1_ADDR 1 #define CONFIG_HAS_ETH1 1 /* add support for "eth1addr" */ +#endif /* CONFIG_BAMBOO_NAND */ + #define CONFIG_NO_PHY_RESET 1 /* no PHY reset on bamboo!!! */ #define CFG_RX_ETH_BUFFER 32 /* Number of ethernet rx buffers & descriptors */ @@ -228,8 +300,15 @@ #define USB_2_0_DEVICE #endif /*CONFIG_440EP*/ +#ifdef CONFIG_BAMBOO_NAND +#define _CFG_CMD_NAND CFG_CMD_NAND +#else +#define _CFG_CMD_NAND 0 +#endif /* CONFIG_BAMBOO_NAND */ + #define CONFIG_COMMANDS (CONFIG_CMD_DFL | \ CFG_CMD_ASKENV | \ + CFG_CMD_EEPROM | \ CFG_CMD_DATE | \ CFG_CMD_DHCP | \ CFG_CMD_DIAG | \ @@ -244,6 +323,7 @@ CFG_CMD_REGINFO | \ CFG_CMD_SDRAM | \ CFG_CMD_USB | \ + _CFG_CMD_NAND | \ CFG_CMD_SNTP ) /* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */ @@ -253,42 +333,42 @@ * Miscellaneous configurable options */ #define CFG_LONGHELP /* undef to save memory */ -#define CFG_PROMPT "=> " /* Monitor Command Prompt */ +#define CFG_PROMPT "=> " /* Monitor Command Prompt */ #if (CONFIG_COMMANDS & CFG_CMD_KGDB) -#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */ +#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */ #else -#define CFG_CBSIZE 256 /* Console I/O Buffer Size */ +#define CFG_CBSIZE 256 /* Console I/O Buffer Size */ #endif -#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */ -#define CFG_MAXARGS 16 /* max number of command args */ -#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */ +#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */ +#define CFG_MAXARGS 16 /* max number of command args */ +#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */ -#define CFG_MEMTEST_START 0x0400000 /* memtest works on */ -#define CFG_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */ +#define CFG_MEMTEST_START 0x0400000 /* memtest works on */ +#define CFG_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */ #define CFG_LOAD_ADDR 0x100000 /* default load address */ -#define CFG_EXTBDINFO 1 /* To use extended board_into (bd_t) */ -#define CONFIG_LYNXKDI 1 /* support kdi files */ +#define CFG_EXTBDINFO 1 /* To use extended board_into (bd_t) */ +#define CONFIG_LYNXKDI 1 /* support kdi files */ -#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */ +#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */ /*----------------------------------------------------------------------- * PCI stuff *----------------------------------------------------------------------- */ /* General PCI */ -#define CONFIG_PCI /* include pci support */ -#undef CONFIG_PCI_PNP /* do (not) pci plug-and-play */ +#define CONFIG_PCI /* include pci support */ +#undef CONFIG_PCI_PNP /* do (not) pci plug-and-play */ #define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */ -#define CFG_PCI_TARGBASE 0x80000000 /* PCIaddr mapped to CFG_PCI_MEMBASE */ +#define CFG_PCI_TARGBASE 0x80000000 /* PCIaddr mapped to CFG_PCI_MEMBASE*/ /* Board-specific PCI */ #define CFG_PCI_PRE_INIT /* enable board pci_pre_init() */ #define CFG_PCI_TARGET_INIT #define CFG_PCI_MASTER_INIT -#define CFG_PCI_SUBSYS_VENDORID 0x1014 /* IBM */ -#define CFG_PCI_SUBSYS_ID 0xcafe /* Whatever */ +#define CFG_PCI_SUBSYS_VENDORID 0x10e8 /* AMCC */ +#define CFG_PCI_SUBSYS_ID 0xcafe /* Whatever */ /* * For booting Linux, the board info and command line data @@ -300,7 +380,7 @@ /*----------------------------------------------------------------------- * Cache Configuration */ -#define CFG_DCACHE_SIZE 32768 /* For IBM 440 CPUs */ +#define CFG_DCACHE_SIZE (32<<10) /* For IBM 440 CPUs */ #define CFG_CACHELINE_SIZE 32 /* ... */ #if (CONFIG_COMMANDS & CFG_CMD_KGDB) #define CFG_CACHELINE_SHIFT 5 /* log base 2 of the above value */ -- 2.7.4