From c019c18da10dae244308f584707804d0c148fe0b Mon Sep 17 00:00:00 2001 From: Lukas Wunner Date: Thu, 12 Oct 2017 12:40:10 +0200 Subject: [PATCH] dt-bindings: gpio: max3191x: Document new driver Add device tree bindings for Maxim MAX3191x industrial serializer. Cc: Mathias Duckeck Signed-off-by: Lukas Wunner Acked-by: Rob Herring Signed-off-by: Linus Walleij --- .../devicetree/bindings/gpio/gpio-max3191x.txt | 59 ++++++++++++++++++++++ 1 file changed, 59 insertions(+) create mode 100644 Documentation/devicetree/bindings/gpio/gpio-max3191x.txt diff --git a/Documentation/devicetree/bindings/gpio/gpio-max3191x.txt b/Documentation/devicetree/bindings/gpio/gpio-max3191x.txt new file mode 100644 index 0000000..b3a6444 --- /dev/null +++ b/Documentation/devicetree/bindings/gpio/gpio-max3191x.txt @@ -0,0 +1,59 @@ +GPIO driver for Maxim MAX3191x industrial serializer + +Required properties: + - compatible: Must be one of: + "maxim,max31910" + "maxim,max31911" + "maxim,max31912" + "maxim,max31913" + "maxim,max31953" + "maxim,max31963" + - reg: Chip select number. + - gpio-controller: Marks the device node as a GPIO controller. + - #gpio-cells: Should be two. For consumer use see gpio.txt. + +Optional properties: + - #daisy-chained-devices: + Number of chips in the daisy-chain (default is 1). + - maxim,modesel-gpios: GPIO pins to configure modesel of each chip. + The number of GPIOs must equal "#daisy-chained-devices" + (if each chip is driven by a separate pin) or 1 + (if all chips are wired to the same pin). + - maxim,fault-gpios: GPIO pins to read fault of each chip. + The number of GPIOs must equal "#daisy-chained-devices" + or 1. + - maxim,db0-gpios: GPIO pins to configure debounce of each chip. + The number of GPIOs must equal "#daisy-chained-devices" + or 1. + - maxim,db1-gpios: GPIO pins to configure debounce of each chip. + The number of GPIOs must equal "maxim,db0-gpios". + - maxim,modesel-8bit: Boolean whether the modesel pin of the chips is + pulled high (8-bit mode). Use this if the modesel pin + is hardwired and consequently "maxim,modesel-gpios" + cannot be specified. By default if neither this nor + "maxim,modesel-gpios" is given, the driver assumes + that modesel is pulled low (16-bit mode). + - maxim,ignore-undervoltage: + Boolean whether to ignore undervoltage alarms signaled + by the "maxim,fault-gpios" or by the status byte + (in 16-bit mode). Use this if the chips are powered + through 5VOUT instead of VCC24V, in which case they + will constantly signal undervoltage. + +For other required and optional properties of SPI slave nodes please refer to +../spi/spi-bus.txt. + +Example: + gpio@0 { + compatible = "maxim,max31913"; + reg = <0>; + gpio-controller; + #gpio-cells = <2>; + + maxim,modesel-gpios = <&gpio2 23>; + maxim,fault-gpios = <&gpio2 24 GPIO_ACTIVE_LOW>; + maxim,db0-gpios = <&gpio2 25>; + maxim,db1-gpios = <&gpio2 26>; + + spi-max-frequency = <25000000>; + }; -- 2.7.4