From bad4d335d7c1b6be43e22adf5c5a279a4f5035e5 Mon Sep 17 00:00:00 2001 From: Stefan Wahren Date: Tue, 7 Mar 2023 19:40:03 +0100 Subject: [PATCH] ARM: dts: imx28-duckbill: Convert to use label references These I2SE board files still use node name and unit address to reference parts from the imx28.dtsi . This causes a lot of redundancy. So use label references in order to make it easier to maintain. Signed-off-by: Stefan Wahren Cc: Michael Heimpold Signed-off-by: Shawn Guo --- arch/arm/boot/dts/imx28-duckbill-2.dts | 256 ++++++++++++++++----------------- arch/arm/boot/dts/imx28-duckbill.dts | 196 ++++++++++++------------- 2 files changed, 218 insertions(+), 234 deletions(-) diff --git a/arch/arm/boot/dts/imx28-duckbill-2.dts b/arch/arm/boot/dts/imx28-duckbill-2.dts index 23fd303..4e28212 100644 --- a/arch/arm/boot/dts/imx28-duckbill-2.dts +++ b/arch/arm/boot/dts/imx28-duckbill-2.dts @@ -18,138 +18,6 @@ reg = <0x40000000 0x08000000>; }; - apb@80000000 { - apbh@80000000 { - ssp0: spi@80010000 { - compatible = "fsl,imx28-mmc"; - pinctrl-names = "default"; - pinctrl-0 = <&mmc0_8bit_pins_a - &mmc0_cd_cfg &mmc0_sck_cfg>; - bus-width = <8>; - vmmc-supply = <®_3p3v>; - status = "okay"; - non-removable; - }; - - ssp2: spi@80014000 { - compatible = "fsl,imx28-mmc"; - pinctrl-names = "default"; - pinctrl-0 = <&mmc2_4bit_pins_b - &mmc2_cd_cfg &mmc2_sck_cfg_b>; - bus-width = <4>; - vmmc-supply = <®_3p3v>; - status = "okay"; - }; - - pinctrl@80018000 { - pinctrl-names = "default"; - pinctrl-0 = <&hog_pins_a>; - - hog_pins_a: hog@0 { - reg = <0>; - fsl,pinmux-ids = < - MX28_PAD_LCD_D17__GPIO_1_17 /* Revision detection */ - >; - fsl,drive-strength = ; - fsl,voltage = ; - fsl,pull-up = ; - }; - - mac0_phy_reset_pin: mac0-phy-reset@0 { - reg = <0>; - fsl,pinmux-ids = < - MX28_PAD_GPMI_ALE__GPIO_0_26 /* PHY Reset */ - >; - fsl,drive-strength = ; - fsl,voltage = ; - fsl,pull-up = ; - }; - - mac0_phy_int_pin: mac0-phy-int@0 { - reg = <0>; - fsl,pinmux-ids = < - MX28_PAD_GPMI_D07__GPIO_0_7 /* PHY Interrupt */ - >; - fsl,drive-strength = ; - fsl,voltage = ; - fsl,pull-up = ; - }; - - led_pins: leds@0 { - reg = <0>; - fsl,pinmux-ids = < - MX28_PAD_SAIF0_MCLK__GPIO_3_20 - MX28_PAD_SAIF0_LRCLK__GPIO_3_21 - >; - fsl,drive-strength = ; - fsl,voltage = ; - fsl,pull-up = ; - }; - }; - }; - - apbx@80040000 { - lradc@80050000 { - status = "okay"; - }; - - i2c0: i2c@80058000 { - pinctrl-names = "default"; - pinctrl-0 = <&i2c0_pins_a>; - status = "okay"; - }; - - auart0: serial@8006a000 { - pinctrl-names = "default"; - pinctrl-0 = <&auart0_2pins_a>; - status = "okay"; - }; - - duart: serial@80074000 { - pinctrl-names = "default"; - pinctrl-0 = <&duart_pins_a>; - status = "okay"; - }; - - usbphy0: usbphy@8007c000 { - status = "okay"; - }; - }; - }; - - ahb@80080000 { - usb0: usb@80080000 { - status = "okay"; - dr_mode = "peripheral"; - }; - - mac0: ethernet@800f0000 { - phy-mode = "rmii"; - pinctrl-names = "default"; - pinctrl-0 = <&mac0_pins_a>, <&mac0_phy_reset_pin>; - phy-supply = <®_3p3v>; - phy-reset-gpios = <&gpio0 26 GPIO_ACTIVE_LOW>; - phy-reset-duration = <25>; - phy-handle = <ðphy>; - status = "okay"; - - mdio { - #address-cells = <1>; - #size-cells = <0>; - - ethphy: ethernet-phy@0 { - compatible = "ethernet-phy-ieee802.3-c22"; - reg = <0>; - pinctrl-names = "default"; - pinctrl-0 = <&mac0_phy_int_pin>; - interrupt-parent = <&gpio0>; - interrupts = <7 IRQ_TYPE_EDGE_FALLING>; - max-speed = <100>; - }; - }; - }; - }; - reg_3p3v: regulator-3p3v { compatible = "regulator-fixed"; regulator-name = "3P3V"; @@ -176,3 +44,127 @@ }; }; }; + +&auart0 { + pinctrl-names = "default"; + pinctrl-0 = <&auart0_2pins_a>; + status = "okay"; +}; + +&duart { + pinctrl-names = "default"; + pinctrl-0 = <&duart_pins_a>; + status = "okay"; +}; + +&i2c0 { + pinctrl-names = "default"; + pinctrl-0 = <&i2c0_pins_a>; + status = "okay"; +}; + +&lradc { + status = "okay"; +}; + +&mac0 { + phy-mode = "rmii"; + pinctrl-names = "default"; + pinctrl-0 = <&mac0_pins_a>, <&mac0_phy_reset_pin>; + phy-supply = <®_3p3v>; + phy-reset-gpios = <&gpio0 26 GPIO_ACTIVE_LOW>; + phy-reset-duration = <25>; + phy-handle = <ðphy>; + status = "okay"; + + mdio { + #address-cells = <1>; + #size-cells = <0>; + + ethphy: ethernet-phy@0 { + compatible = "ethernet-phy-ieee802.3-c22"; + reg = <0>; + pinctrl-names = "default"; + pinctrl-0 = <&mac0_phy_int_pin>; + interrupt-parent = <&gpio0>; + interrupts = <7 IRQ_TYPE_EDGE_FALLING>; + max-speed = <100>; + }; + }; +}; + +&pinctrl { + pinctrl-names = "default"; + pinctrl-0 = <&hog_pins_a>; + + hog_pins_a: hog@0 { + reg = <0>; + fsl,pinmux-ids = < + MX28_PAD_LCD_D17__GPIO_1_17 /* Revision detection */ + >; + fsl,drive-strength = ; + fsl,voltage = ; + fsl,pull-up = ; + }; + + mac0_phy_reset_pin: mac0-phy-reset@0 { + reg = <0>; + fsl,pinmux-ids = < + MX28_PAD_GPMI_ALE__GPIO_0_26 /* PHY Reset */ + >; + fsl,drive-strength = ; + fsl,voltage = ; + fsl,pull-up = ; + }; + + mac0_phy_int_pin: mac0-phy-int@0 { + reg = <0>; + fsl,pinmux-ids = < + MX28_PAD_GPMI_D07__GPIO_0_7 /* PHY Interrupt */ + >; + fsl,drive-strength = ; + fsl,voltage = ; + fsl,pull-up = ; + }; + + led_pins: leds@0 { + reg = <0>; + fsl,pinmux-ids = < + MX28_PAD_SAIF0_MCLK__GPIO_3_20 + MX28_PAD_SAIF0_LRCLK__GPIO_3_21 + >; + fsl,drive-strength = ; + fsl,voltage = ; + fsl,pull-up = ; + }; +}; + +&ssp0 { + compatible = "fsl,imx28-mmc"; + pinctrl-names = "default"; + pinctrl-0 = <&mmc0_8bit_pins_a + &mmc0_cd_cfg &mmc0_sck_cfg>; + bus-width = <8>; + vmmc-supply = <®_3p3v>; + status = "okay"; + non-removable; +}; + +&ssp2 { + compatible = "fsl,imx28-mmc"; + pinctrl-names = "default"; + pinctrl-0 = <&mmc2_4bit_pins_b + &mmc2_cd_cfg &mmc2_sck_cfg_b>; + bus-width = <4>; + vmmc-supply = <®_3p3v>; + status = "okay"; +}; + +&usb0 { + status = "okay"; + dr_mode = "peripheral"; +}; + +&usbphy0 { + status = "okay"; +}; diff --git a/arch/arm/boot/dts/imx28-duckbill.dts b/arch/arm/boot/dts/imx28-duckbill.dts index c666afb..13ffd53 100644 --- a/arch/arm/boot/dts/imx28-duckbill.dts +++ b/arch/arm/boot/dts/imx28-duckbill.dts @@ -17,108 +17,6 @@ reg = <0x40000000 0x08000000>; }; - apb@80000000 { - apbh@80000000 { - ssp0: spi@80010000 { - compatible = "fsl,imx28-mmc"; - pinctrl-names = "default"; - pinctrl-0 = <&mmc0_4bit_pins_a - &mmc0_cd_cfg &mmc0_sck_cfg>; - bus-width = <4>; - vmmc-supply = <®_3p3v>; - status = "okay"; - }; - - ssp2: spi@80014000 { - compatible = "fsl,imx28-spi"; - pinctrl-names = "default"; - pinctrl-0 = <&spi2_pins_a>; - status = "okay"; - }; - - pinctrl@80018000 { - pinctrl-names = "default"; - pinctrl-0 = <&hog_pins_a>; - - hog_pins_a: hog@0 { - reg = <0>; - fsl,pinmux-ids = < - MX28_PAD_LCD_D17__GPIO_1_17 /* Revision detection */ - >; - fsl,drive-strength = ; - fsl,voltage = ; - fsl,pull-up = ; - }; - - mac0_phy_reset_pin: mac0-phy-reset@0 { - reg = <0>; - fsl,pinmux-ids = < - MX28_PAD_SSP0_DATA7__GPIO_2_7 /* PHY Reset */ - >; - fsl,drive-strength = ; - fsl,voltage = ; - fsl,pull-up = ; - }; - - led_pins: leds@0 { - reg = <0>; - fsl,pinmux-ids = < - MX28_PAD_AUART1_RX__GPIO_3_4 - MX28_PAD_AUART1_TX__GPIO_3_5 - >; - fsl,drive-strength = ; - fsl,voltage = ; - fsl,pull-up = ; - }; - }; - }; - - apbx@80040000 { - lradc@80050000 { - status = "okay"; - }; - - i2c0: i2c@80058000 { - pinctrl-names = "default"; - pinctrl-0 = <&i2c0_pins_a>; - status = "okay"; - }; - - auart0: serial@8006a000 { - pinctrl-names = "default"; - pinctrl-0 = <&auart0_2pins_a>; - status = "okay"; - }; - - duart: serial@80074000 { - pinctrl-names = "default"; - pinctrl-0 = <&duart_pins_a>; - status = "okay"; - }; - - usbphy0: usbphy@8007c000 { - status = "okay"; - }; - }; - }; - - ahb@80080000 { - usb0: usb@80080000 { - status = "okay"; - dr_mode = "peripheral"; - }; - - mac0: ethernet@800f0000 { - phy-mode = "rmii"; - pinctrl-names = "default"; - pinctrl-0 = <&mac0_pins_a>, <&mac0_phy_reset_pin>; - phy-supply = <®_3p3v>; - phy-reset-gpios = <&gpio2 7 GPIO_ACTIVE_LOW>; - phy-reset-duration = <25>; - status = "okay"; - }; - }; - reg_3p3v: regulator-3p3v { compatible = "regulator-fixed"; regulator-name = "3P3V"; @@ -145,3 +43,97 @@ }; }; }; + +&auart0 { + pinctrl-names = "default"; + pinctrl-0 = <&auart0_2pins_a>; + status = "okay"; +}; + +&duart { + pinctrl-names = "default"; + pinctrl-0 = <&duart_pins_a>; + status = "okay"; +}; + +&lradc { + status = "okay"; +}; + +&i2c0 { + pinctrl-names = "default"; + pinctrl-0 = <&i2c0_pins_a>; + status = "okay"; +}; + +&mac0 { + phy-mode = "rmii"; + pinctrl-names = "default"; + pinctrl-0 = <&mac0_pins_a>, <&mac0_phy_reset_pin>; + phy-supply = <®_3p3v>; + phy-reset-gpios = <&gpio2 7 GPIO_ACTIVE_LOW>; + phy-reset-duration = <25>; + status = "okay"; +}; + +&pinctrl { + pinctrl-names = "default"; + pinctrl-0 = <&hog_pins_a>; + + hog_pins_a: hog@0 { + reg = <0>; + fsl,pinmux-ids = < + MX28_PAD_LCD_D17__GPIO_1_17 /* Revision detection */ + >; + fsl,drive-strength = ; + fsl,voltage = ; + fsl,pull-up = ; + }; + + mac0_phy_reset_pin: mac0-phy-reset@0 { + reg = <0>; + fsl,pinmux-ids = < + MX28_PAD_SSP0_DATA7__GPIO_2_7 /* PHY Reset */ + >; + fsl,drive-strength = ; + fsl,voltage = ; + fsl,pull-up = ; + }; + + led_pins: leds@0 { + reg = <0>; + fsl,pinmux-ids = < + MX28_PAD_AUART1_RX__GPIO_3_4 + MX28_PAD_AUART1_TX__GPIO_3_5 + >; + fsl,drive-strength = ; + fsl,voltage = ; + fsl,pull-up = ; + }; +}; + +&ssp0 { + compatible = "fsl,imx28-mmc"; + pinctrl-names = "default"; + pinctrl-0 = <&mmc0_4bit_pins_a + &mmc0_cd_cfg &mmc0_sck_cfg>; + bus-width = <4>; + vmmc-supply = <®_3p3v>; + status = "okay"; +}; + +&ssp2 { + compatible = "fsl,imx28-spi"; + pinctrl-names = "default"; + pinctrl-0 = <&spi2_pins_a>; + status = "okay"; +}; + +&usb0 { + dr_mode = "peripheral"; + status = "okay"; +}; + +&usbphy0 { + status = "okay"; +}; -- 2.7.4