From b4e6153704dda5bef78dd59324205b5e61829499 Mon Sep 17 00:00:00 2001 From: Nicolas Pitre Date: Mon, 18 Feb 2013 23:11:30 -0500 Subject: [PATCH] ARM: mach-imx: move early resume code out of the .data section Building the kernel with allyesconfig fails because the i.mx early resume code located in the .data section is unable to fixup the bl relocation as the branch target gets too far away. The idea of having code in the .data section allows for easy access to nearby data using relative addressing while the MMU is off. However it is probably best to move the code back to the .text section where it belongs and fixup the data access instead. This solves the bl reloc issue (at least until this becomes a general problem) and simplifies the code as well. Signed-off-by: Nicolas Pitre Signed-off-by: Shawn Guo --- arch/arm/mach-imx/headsmp.S | 18 +++++++++--------- arch/arm/mach-imx/pm-imx6q.c | 15 --------------- 2 files changed, 9 insertions(+), 24 deletions(-) diff --git a/arch/arm/mach-imx/headsmp.S b/arch/arm/mach-imx/headsmp.S index 921fc15..a58c8b0 100644 --- a/arch/arm/mach-imx/headsmp.S +++ b/arch/arm/mach-imx/headsmp.S @@ -26,16 +26,16 @@ ENDPROC(v7_secondary_startup) #ifdef CONFIG_PM /* - * The following code is located into the .data section. This is to - * allow phys_l2x0_saved_regs to be accessed with a relative load - * as we are running on physical address here. + * The following code must assume it is running from physical address + * where absolute virtual addresses to the data section have to be + * turned into relative ones. */ - .data - .align #ifdef CONFIG_CACHE_L2X0 .macro pl310_resume - ldr r2, phys_l2x0_saved_regs + adr r0, l2x0_saved_regs_offset + ldr r2, [r0] + add r2, r2, r0 ldr r0, [r2, #L2X0_R_PHY_BASE] @ get physical base of l2x0 ldr r1, [r2, #L2X0_R_AUX_CTRL] @ get aux_ctrl value str r1, [r0, #L2X0_AUX_CTRL] @ restore aux_ctrl @@ -43,9 +43,9 @@ ENDPROC(v7_secondary_startup) str r1, [r0, #L2X0_CTRL] @ re-enable L2 .endm - .globl phys_l2x0_saved_regs -phys_l2x0_saved_regs: - .long 0 +l2x0_saved_regs_offset: + .word l2x0_saved_regs - . + #else .macro pl310_resume .endm diff --git a/arch/arm/mach-imx/pm-imx6q.c b/arch/arm/mach-imx/pm-imx6q.c index ee42d20..5faba7a 100644 --- a/arch/arm/mach-imx/pm-imx6q.c +++ b/arch/arm/mach-imx/pm-imx6q.c @@ -22,8 +22,6 @@ #include "common.h" #include "hardware.h" -extern unsigned long phys_l2x0_saved_regs; - static int imx6q_suspend_finish(unsigned long val) { cpu_do_idle(); @@ -57,18 +55,5 @@ static const struct platform_suspend_ops imx6q_pm_ops = { void __init imx6q_pm_init(void) { - /* - * The l2x0 core code provides an infrastucture to save and restore - * l2x0 registers across suspend/resume cycle. But because imx6q - * retains L2 content during suspend and needs to resume L2 before - * MMU is enabled, it can only utilize register saving support and - * have to take care of restoring on its own. So we save physical - * address of the data structure used by l2x0 core to save registers, - * and later restore the necessary ones in imx6q resume entry. - */ -#ifdef CONFIG_CACHE_L2X0 - phys_l2x0_saved_regs = __pa(&l2x0_saved_regs); -#endif - suspend_set_ops(&imx6q_pm_ops); } -- 2.7.4