From b4cdc8f61beb2a55c8c3d22dfcaf5f34a919fe9b Mon Sep 17 00:00:00 2001 From: Huang Shijie Date: Mon, 8 Jul 2013 17:14:18 +0800 Subject: [PATCH] serial: imx: add DMA support for imx6q We only enable the DMA support when the following are meet: [1] The uart port supports the hardware flow control(CTS/RTS). (Some uart port does not support the CTS/RTS.) [2] The application enables the CTS/RTS. [3] The Soc is imx6q. For the sdma's firmware limit, we do not support the DMA except the imx6q platform. [4] The uart is not used as a console. Signed-off-by: Huang Shijie Signed-off-by: Greg Kroah-Hartman --- drivers/tty/serial/imx.c | 405 ++++++++++++++++++++++++++++++++++++++++++++++- 1 file changed, 400 insertions(+), 5 deletions(-) diff --git a/drivers/tty/serial/imx.c b/drivers/tty/serial/imx.c index 79d1943..90655b8 100644 --- a/drivers/tty/serial/imx.c +++ b/drivers/tty/serial/imx.c @@ -48,9 +48,11 @@ #include #include #include +#include #include #include +#include /* Register definitions */ #define URXD0 0x0 /* Receiver Register */ @@ -82,6 +84,7 @@ #define UCR1_ADBR (1<<14) /* Auto detect baud rate */ #define UCR1_TRDYEN (1<<13) /* Transmitter ready interrupt enable */ #define UCR1_IDEN (1<<12) /* Idle condition interrupt */ +#define UCR1_ICD_REG(x) (((x) & 3) << 10) /* idle condition detect */ #define UCR1_RRDYEN (1<<9) /* Recv ready interrupt enable */ #define UCR1_RDMAEN (1<<8) /* Recv ready DMA enable */ #define UCR1_IREN (1<<7) /* Infrared interface enable */ @@ -90,6 +93,7 @@ #define UCR1_SNDBRK (1<<4) /* Send break */ #define UCR1_TDMAEN (1<<3) /* Transmitter ready DMA enable */ #define IMX1_UCR1_UARTCLKEN (1<<2) /* UART clock enabled, i.mx1 only */ +#define UCR1_ATDMAEN (1<<2) /* Aging DMA Timer Enable */ #define UCR1_DOZE (1<<1) /* Doze */ #define UCR1_UARTEN (1<<0) /* UART enabled */ #define UCR2_ESCI (1<<15) /* Escape seq interrupt enable */ @@ -125,6 +129,7 @@ #define UCR4_ENIRI (1<<8) /* Serial infrared interrupt enable */ #define UCR4_WKEN (1<<7) /* Wake interrupt enable */ #define UCR4_REF16 (1<<6) /* Ref freq 16 MHz */ +#define UCR4_IDDMAEN (1<<6) /* DMA IDLE Condition Detected */ #define UCR4_IRSC (1<<5) /* IR special case */ #define UCR4_TCEN (1<<3) /* Transmit complete interrupt enable */ #define UCR4_BKEN (1<<2) /* Break condition interrupt enable */ @@ -209,6 +214,19 @@ struct imx_port { struct clk *clk_ipg; struct clk *clk_per; const struct imx_uart_data *devdata; + + /* DMA fields */ + unsigned int dma_is_inited:1; + unsigned int dma_is_enabled:1; + unsigned int dma_is_rxing:1; + unsigned int dma_is_txing:1; + struct dma_chan *dma_chan_rx, *dma_chan_tx; + struct scatterlist rx_sgl, tx_sgl[2]; + void *rx_buf; + unsigned int rx_bytes, tx_bytes; + struct work_struct tsk_dma_rx, tsk_dma_tx; + unsigned int dma_tx_nents; + wait_queue_head_t dma_wait; }; struct imx_port_ucrs { @@ -399,6 +417,13 @@ static void imx_stop_tx(struct uart_port *port) return; } + /* + * We are maybe in the SMP context, so if the DMA TX thread is running + * on other cpu, we have to wait for it to finish. + */ + if (sport->dma_is_enabled && sport->dma_is_txing) + return; + temp = readl(sport->port.membase + UCR1); writel(temp & ~UCR1_TXMPTYEN, sport->port.membase + UCR1); } @@ -411,6 +436,13 @@ static void imx_stop_rx(struct uart_port *port) struct imx_port *sport = (struct imx_port *)port; unsigned long temp; + /* + * We are maybe in the SMP context, so if the DMA TX thread is running + * on other cpu, we have to wait for it to finish. + */ + if (sport->dma_is_enabled && sport->dma_is_rxing) + return; + temp = readl(sport->port.membase + UCR2); writel(temp & ~UCR2_RXEN, sport->port.membase + UCR2); } @@ -446,6 +478,95 @@ static inline void imx_transmit_buffer(struct imx_port *sport) imx_stop_tx(&sport->port); } +static void dma_tx_callback(void *data) +{ + struct imx_port *sport = data; + struct scatterlist *sgl = &sport->tx_sgl[0]; + struct circ_buf *xmit = &sport->port.state->xmit; + unsigned long flags; + + dma_unmap_sg(sport->port.dev, sgl, sport->dma_tx_nents, DMA_TO_DEVICE); + + sport->dma_is_txing = 0; + + /* update the stat */ + spin_lock_irqsave(&sport->port.lock, flags); + xmit->tail = (xmit->tail + sport->tx_bytes) & (UART_XMIT_SIZE - 1); + sport->port.icount.tx += sport->tx_bytes; + spin_unlock_irqrestore(&sport->port.lock, flags); + + dev_dbg(sport->port.dev, "we finish the TX DMA.\n"); + + if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS) + uart_write_wakeup(&sport->port); + + if (waitqueue_active(&sport->dma_wait)) { + wake_up(&sport->dma_wait); + dev_dbg(sport->port.dev, "exit in %s.\n", __func__); + return; + } + + schedule_work(&sport->tsk_dma_tx); +} + +static void dma_tx_work(struct work_struct *w) +{ + struct imx_port *sport = container_of(w, struct imx_port, tsk_dma_tx); + struct circ_buf *xmit = &sport->port.state->xmit; + struct scatterlist *sgl = sport->tx_sgl; + struct dma_async_tx_descriptor *desc; + struct dma_chan *chan = sport->dma_chan_tx; + struct device *dev = sport->port.dev; + enum dma_status status; + unsigned long flags; + int ret; + + status = chan->device->device_tx_status(chan, (dma_cookie_t)0, NULL); + if (DMA_IN_PROGRESS == status) + return; + + spin_lock_irqsave(&sport->port.lock, flags); + sport->tx_bytes = uart_circ_chars_pending(xmit); + if (sport->tx_bytes == 0) { + spin_unlock_irqrestore(&sport->port.lock, flags); + return; + } + + if (xmit->tail > xmit->head) { + sport->dma_tx_nents = 2; + sg_init_table(sgl, 2); + sg_set_buf(sgl, xmit->buf + xmit->tail, + UART_XMIT_SIZE - xmit->tail); + sg_set_buf(sgl + 1, xmit->buf, xmit->head); + } else { + sport->dma_tx_nents = 1; + sg_init_one(sgl, xmit->buf + xmit->tail, sport->tx_bytes); + } + spin_unlock_irqrestore(&sport->port.lock, flags); + + ret = dma_map_sg(dev, sgl, sport->dma_tx_nents, DMA_TO_DEVICE); + if (ret == 0) { + dev_err(dev, "DMA mapping error for TX.\n"); + return; + } + desc = dmaengine_prep_slave_sg(chan, sgl, sport->dma_tx_nents, + DMA_MEM_TO_DEV, DMA_PREP_INTERRUPT); + if (!desc) { + dev_err(dev, "We cannot prepare for the TX slave dma!\n"); + return; + } + desc->callback = dma_tx_callback; + desc->callback_param = sport; + + dev_dbg(dev, "TX: prepare to send %lu bytes by DMA.\n", + uart_circ_chars_pending(xmit)); + /* fire it */ + sport->dma_is_txing = 1; + dmaengine_submit(desc); + dma_async_issue_pending(chan); + return; +} + /* * interrupts disabled on entry */ @@ -472,8 +593,10 @@ static void imx_start_tx(struct uart_port *port) temp |= UCR4_OREN; writel(temp, sport->port.membase + UCR4); - temp = readl(sport->port.membase + UCR1); - writel(temp | UCR1_TXMPTYEN, sport->port.membase + UCR1); + if (!sport->dma_is_enabled) { + temp = readl(sport->port.membase + UCR1); + writel(temp | UCR1_TXMPTYEN, sport->port.membase + UCR1); + } if (USE_IRDA(sport)) { temp = readl(sport->port.membase + UCR1); @@ -485,6 +608,15 @@ static void imx_start_tx(struct uart_port *port) writel(temp, sport->port.membase + UCR4); } + if (sport->dma_is_enabled) { + /* + * We may in the interrupt context, so arise a work_struct to + * do the real job. + */ + schedule_work(&sport->tsk_dma_tx); + return; + } + if (readl(sport->port.membase + uts_reg(sport)) & UTS_TXEMPTY) imx_transmit_buffer(sport); } @@ -600,6 +732,28 @@ out: return IRQ_HANDLED; } +/* + * If the RXFIFO is filled with some data, and then we + * arise a DMA operation to receive them. + */ +static void imx_dma_rxint(struct imx_port *sport) +{ + unsigned long temp; + + temp = readl(sport->port.membase + USR2); + if ((temp & USR2_RDR) && !sport->dma_is_rxing) { + sport->dma_is_rxing = 1; + + /* disable the `Recerver Ready Interrrupt` */ + temp = readl(sport->port.membase + UCR1); + temp &= ~(UCR1_RRDYEN); + writel(temp, sport->port.membase + UCR1); + + /* tell the DMA to receive the data. */ + schedule_work(&sport->tsk_dma_rx); + } +} + static irqreturn_t imx_int(int irq, void *dev_id) { struct imx_port *sport = dev_id; @@ -608,8 +762,12 @@ static irqreturn_t imx_int(int irq, void *dev_id) sts = readl(sport->port.membase + USR1); - if (sts & USR1_RRDY) - imx_rxint(irq, dev_id); + if (sts & USR1_RRDY) { + if (sport->dma_is_enabled) + imx_dma_rxint(sport); + else + imx_rxint(irq, dev_id); + } if (sts & USR1_TRDY && readl(sport->port.membase + UCR1) & UCR1_TXMPTYEN) @@ -666,7 +824,8 @@ static void imx_set_mctrl(struct uart_port *port, unsigned int mctrl) temp = readl(sport->port.membase + UCR2) & ~UCR2_CTS; if (mctrl & TIOCM_RTS) - temp |= UCR2_CTS; + if (!sport->dma_is_enabled) + temp |= UCR2_CTS; writel(temp, sport->port.membase + UCR2); } @@ -705,6 +864,226 @@ static int imx_setup_ufcr(struct imx_port *sport, unsigned int mode) return 0; } +#define RX_BUF_SIZE (PAGE_SIZE) +static int start_rx_dma(struct imx_port *sport); +static void dma_rx_work(struct work_struct *w) +{ + struct imx_port *sport = container_of(w, struct imx_port, tsk_dma_rx); + struct tty_port *port = &sport->port.state->port; + + if (sport->rx_bytes) { + tty_insert_flip_string(port, sport->rx_buf, sport->rx_bytes); + tty_flip_buffer_push(port); + sport->rx_bytes = 0; + } + + if (sport->dma_is_rxing) + start_rx_dma(sport); +} + +static void imx_rx_dma_done(struct imx_port *sport) +{ + unsigned long temp; + + /* Enable this interrupt when the RXFIFO is empty. */ + temp = readl(sport->port.membase + UCR1); + temp |= UCR1_RRDYEN; + writel(temp, sport->port.membase + UCR1); + + sport->dma_is_rxing = 0; + + /* Is the shutdown waiting for us? */ + if (waitqueue_active(&sport->dma_wait)) + wake_up(&sport->dma_wait); +} + +/* + * There are three kinds of RX DMA interrupts(such as in the MX6Q): + * [1] the RX DMA buffer is full. + * [2] the Aging timer expires(wait for 8 bytes long) + * [3] the Idle Condition Detect(enabled the UCR4_IDDMAEN). + * + * The [2] is trigger when a character was been sitting in the FIFO + * meanwhile [3] can wait for 32 bytes long when the RX line is + * on IDLE state and RxFIFO is empty. + */ +static void dma_rx_callback(void *data) +{ + struct imx_port *sport = data; + struct dma_chan *chan = sport->dma_chan_rx; + struct scatterlist *sgl = &sport->rx_sgl; + struct dma_tx_state state; + enum dma_status status; + unsigned int count; + + /* unmap it first */ + dma_unmap_sg(sport->port.dev, sgl, 1, DMA_FROM_DEVICE); + + status = chan->device->device_tx_status(chan, (dma_cookie_t)0, &state); + count = RX_BUF_SIZE - state.residue; + dev_dbg(sport->port.dev, "We get %d bytes.\n", count); + + if (count) { + sport->rx_bytes = count; + schedule_work(&sport->tsk_dma_rx); + } else + imx_rx_dma_done(sport); +} + +static int start_rx_dma(struct imx_port *sport) +{ + struct scatterlist *sgl = &sport->rx_sgl; + struct dma_chan *chan = sport->dma_chan_rx; + struct device *dev = sport->port.dev; + struct dma_async_tx_descriptor *desc; + int ret; + + sg_init_one(sgl, sport->rx_buf, RX_BUF_SIZE); + ret = dma_map_sg(dev, sgl, 1, DMA_FROM_DEVICE); + if (ret == 0) { + dev_err(dev, "DMA mapping error for RX.\n"); + return -EINVAL; + } + desc = dmaengine_prep_slave_sg(chan, sgl, 1, DMA_DEV_TO_MEM, + DMA_PREP_INTERRUPT); + if (!desc) { + dev_err(dev, "We cannot prepare for the RX slave dma!\n"); + return -EINVAL; + } + desc->callback = dma_rx_callback; + desc->callback_param = sport; + + dev_dbg(dev, "RX: prepare for the DMA.\n"); + dmaengine_submit(desc); + dma_async_issue_pending(chan); + return 0; +} + +static void imx_uart_dma_exit(struct imx_port *sport) +{ + if (sport->dma_chan_rx) { + dma_release_channel(sport->dma_chan_rx); + sport->dma_chan_rx = NULL; + + kfree(sport->rx_buf); + sport->rx_buf = NULL; + } + + if (sport->dma_chan_tx) { + dma_release_channel(sport->dma_chan_tx); + sport->dma_chan_tx = NULL; + } + + sport->dma_is_inited = 0; +} + +static int imx_uart_dma_init(struct imx_port *sport) +{ + struct dma_slave_config slave_config; + struct device *dev = sport->port.dev; + int ret; + + /* Prepare for RX : */ + sport->dma_chan_rx = dma_request_slave_channel(dev, "rx"); + if (!sport->dma_chan_rx) { + dev_dbg(dev, "cannot get the DMA channel.\n"); + ret = -EINVAL; + goto err; + } + + slave_config.direction = DMA_DEV_TO_MEM; + slave_config.src_addr = sport->port.mapbase + URXD0; + slave_config.src_addr_width = DMA_SLAVE_BUSWIDTH_1_BYTE; + slave_config.src_maxburst = RXTL; + ret = dmaengine_slave_config(sport->dma_chan_rx, &slave_config); + if (ret) { + dev_err(dev, "error in RX dma configuration.\n"); + goto err; + } + + sport->rx_buf = kzalloc(PAGE_SIZE, GFP_KERNEL); + if (!sport->rx_buf) { + dev_err(dev, "cannot alloc DMA buffer.\n"); + ret = -ENOMEM; + goto err; + } + sport->rx_bytes = 0; + + /* Prepare for TX : */ + sport->dma_chan_tx = dma_request_slave_channel(dev, "tx"); + if (!sport->dma_chan_tx) { + dev_err(dev, "cannot get the TX DMA channel!\n"); + ret = -EINVAL; + goto err; + } + + slave_config.direction = DMA_MEM_TO_DEV; + slave_config.dst_addr = sport->port.mapbase + URTX0; + slave_config.dst_addr_width = DMA_SLAVE_BUSWIDTH_1_BYTE; + slave_config.dst_maxburst = TXTL; + ret = dmaengine_slave_config(sport->dma_chan_tx, &slave_config); + if (ret) { + dev_err(dev, "error in TX dma configuration."); + goto err; + } + + sport->dma_is_inited = 1; + + return 0; +err: + imx_uart_dma_exit(sport); + return ret; +} + +static void imx_enable_dma(struct imx_port *sport) +{ + unsigned long temp; + struct tty_port *port = &sport->port.state->port; + + port->low_latency = 1; + INIT_WORK(&sport->tsk_dma_tx, dma_tx_work); + INIT_WORK(&sport->tsk_dma_rx, dma_rx_work); + init_waitqueue_head(&sport->dma_wait); + + /* set UCR1 */ + temp = readl(sport->port.membase + UCR1); + temp |= UCR1_RDMAEN | UCR1_TDMAEN | UCR1_ATDMAEN | + /* wait for 32 idle frames for IDDMA interrupt */ + UCR1_ICD_REG(3); + writel(temp, sport->port.membase + UCR1); + + /* set UCR4 */ + temp = readl(sport->port.membase + UCR4); + temp |= UCR4_IDDMAEN; + writel(temp, sport->port.membase + UCR4); + + sport->dma_is_enabled = 1; +} + +static void imx_disable_dma(struct imx_port *sport) +{ + unsigned long temp; + struct tty_port *port = &sport->port.state->port; + + /* clear UCR1 */ + temp = readl(sport->port.membase + UCR1); + temp &= ~(UCR1_RDMAEN | UCR1_TDMAEN | UCR1_ATDMAEN); + writel(temp, sport->port.membase + UCR1); + + /* clear UCR2 */ + temp = readl(sport->port.membase + UCR2); + temp &= ~(UCR2_CTSC | UCR2_CTS); + writel(temp, sport->port.membase + UCR2); + + /* clear UCR4 */ + temp = readl(sport->port.membase + UCR4); + temp &= ~UCR4_IDDMAEN; + writel(temp, sport->port.membase + UCR4); + + sport->dma_is_enabled = 0; + port->low_latency = 0; +} + /* half the RX buffer size */ #define CTSTL 16 @@ -869,6 +1248,15 @@ static void imx_shutdown(struct uart_port *port) unsigned long temp; unsigned long flags; + if (sport->dma_is_enabled) { + /* We have to wait for the DMA to finish. */ + wait_event(sport->dma_wait, + !sport->dma_is_rxing && !sport->dma_is_txing); + imx_stop_rx(port); + imx_disable_dma(sport); + imx_uart_dma_exit(sport); + } + spin_lock_irqsave(&sport->port.lock, flags); temp = readl(sport->port.membase + UCR2); temp &= ~(UCR2_TXEN); @@ -955,6 +1343,11 @@ imx_set_termios(struct uart_port *port, struct ktermios *termios, if (sport->have_rtscts) { ucr2 &= ~UCR2_IRTS; ucr2 |= UCR2_CTSC; + + /* Can we enable the DMA support? */ + if (is_imx6q_uart(sport) && !uart_console(port) + && !sport->dma_is_inited) + imx_uart_dma_init(sport); } else { termios->c_cflag &= ~CRTSCTS; } @@ -1073,6 +1466,8 @@ imx_set_termios(struct uart_port *port, struct ktermios *termios, if (UART_ENABLE_MS(&sport->port, termios->c_cflag)) imx_enable_ms(&sport->port); + if (sport->dma_is_inited && !sport->dma_is_enabled) + imx_enable_dma(sport); spin_unlock_irqrestore(&sport->port.lock, flags); } -- 2.7.4