From a6a22f82c90dab8966fc07bd7e798a0680803995 Mon Sep 17 00:00:00 2001 From: Icenowy Zheng Date: Thu, 2 Jul 2020 10:14:31 +0200 Subject: [PATCH] arm64: dts: sun50i-a64-pinephone: Enable LCD support on PinePhone PinePhone uses PWM backlight and a XBD599 LCD panel over DSI for display. Backlight levels curve was optimized by Martijn Braam using a lux meter. Add its device nodes. Signed-off-by: Icenowy Zheng Signed-off-by: Martijn Braam Signed-off-by: Ondrej Jirman Acked-by: Linus Walleij Link: https://lore.kernel.org/r/20200702081432.1727696-2-megous@megous.com Signed-off-by: Maxime Ripard --- .../dts/allwinner/sun50i-a64-pinephone-1.1.dts | 19 +++++++++++++ .../boot/dts/allwinner/sun50i-a64-pinephone.dtsi | 33 ++++++++++++++++++++++ 2 files changed, 52 insertions(+) diff --git a/arch/arm64/boot/dts/allwinner/sun50i-a64-pinephone-1.1.dts b/arch/arm64/boot/dts/allwinner/sun50i-a64-pinephone-1.1.dts index 06a775c..3e99a87 100644 --- a/arch/arm64/boot/dts/allwinner/sun50i-a64-pinephone-1.1.dts +++ b/arch/arm64/boot/dts/allwinner/sun50i-a64-pinephone-1.1.dts @@ -9,3 +9,22 @@ model = "Pine64 PinePhone Braveheart (1.1)"; compatible = "pine64,pinephone-1.1", "allwinner,sun50i-a64"; }; + +&backlight { + power-supply = <®_ldo_io0>; + /* + * PWM backlight circuit on this PinePhone revision was changed since + * 1.0, and the lowest PWM duty cycle that doesn't lead to backlight + * being off is around 20%. Duty cycle for the lowest brightness level + * also varries quite a bit between individual boards, so the lowest + * value here was chosen as a safe default. + */ + brightness-levels = < + 774 793 814 842 + 882 935 1003 1088 + 1192 1316 1462 1633 + 1830 2054 2309 2596 + 2916 3271 3664 4096>; + num-interpolated-steps = <50>; + default-brightness-level = <400>; +}; diff --git a/arch/arm64/boot/dts/allwinner/sun50i-a64-pinephone.dtsi b/arch/arm64/boot/dts/allwinner/sun50i-a64-pinephone.dtsi index cefda14..a89425a 100644 --- a/arch/arm64/boot/dts/allwinner/sun50i-a64-pinephone.dtsi +++ b/arch/arm64/boot/dts/allwinner/sun50i-a64-pinephone.dtsi @@ -16,6 +16,13 @@ serial0 = &uart0; }; + backlight: backlight { + compatible = "pwm-backlight"; + pwms = <&r_pwm 0 50000 PWM_POLARITY_INVERTED>; + enable-gpios = <&pio 7 10 GPIO_ACTIVE_HIGH>; /* PH10 */ + /* Backlight configuration differs per PinePhone revision. */ + }; + chosen { stdout-path = "serial0:115200n8"; }; @@ -84,6 +91,28 @@ status = "okay"; }; +&de { + status = "okay"; +}; + +&dphy { + status = "okay"; +}; + +&dsi { + vcc-dsi-supply = <®_dldo1>; + status = "okay"; + + panel@0 { + compatible = "xingbangda,xbd599"; + reg = <0>; + reset-gpios = <&pio 3 23 GPIO_ACTIVE_LOW>; /* PD23 */ + iovcc-supply = <®_dldo2>; + vcc-supply = <®_ldo_io0>; + backlight = <&backlight>; + }; +}; + &ehci0 { status = "okay"; }; @@ -188,6 +217,10 @@ */ }; +&r_pwm { + status = "okay"; +}; + &r_rsb { status = "okay"; -- 2.7.4