From 8eb3cef8d2642da6b72179da73344a442461cb58 Mon Sep 17 00:00:00 2001 From: Ioana Radulescu Date: Wed, 28 Aug 2019 17:08:15 +0300 Subject: [PATCH] dpaa2-eth: Add pause frame support Starting with firmware version MC10.18.0, we have support for L2 flow control. Asymmetrical configuration (Rx or Tx only) is supported, but not pause frame autonegotioation. Pause frame configuration is done via ethtool. By default, we start with flow control enabled on both Rx and Tx. Changes are propagated to hardware through firmware commands, using two flags (PAUSE, ASYM_PAUSE) to specify Rx and Tx pause configuration, as follows: PAUSE | ASYM_PAUSE | Rx pause | Tx pause ---------------------------------------- 0 | 0 | disabled | disabled 0 | 1 | disabled | enabled 1 | 0 | enabled | enabled 1 | 1 | enabled | disabled The hardware can automatically send pause frames when the number of buffers in the pool goes below a predefined threshold. Due to this, flow control is incompatible with Rx frame queue taildrop (both mechanisms target the case when processing of ingress frames can't keep up with the Rx rate; for large frames, the number of buffers in the pool may never get low enough to trigger pause frames as long as taildrop is enabled). So we set pause frame generation and Rx FQ taildrop as mutually exclusive. Signed-off-by: Ioana Radulescu Reviewed-by: Andrew Lunn Signed-off-by: David S. Miller --- drivers/net/ethernet/freescale/dpaa2/dpaa2-eth.c | 80 +++++++++++++++++++--- drivers/net/ethernet/freescale/dpaa2/dpaa2-eth.h | 7 ++ .../net/ethernet/freescale/dpaa2/dpaa2-ethtool.c | 55 +++++++++++++++ drivers/net/ethernet/freescale/dpaa2/dpni-cmd.h | 3 +- drivers/net/ethernet/freescale/dpaa2/dpni.c | 40 ++++++++++- drivers/net/ethernet/freescale/dpaa2/dpni.h | 5 ++ 6 files changed, 177 insertions(+), 13 deletions(-) diff --git a/drivers/net/ethernet/freescale/dpaa2/dpaa2-eth.c b/drivers/net/ethernet/freescale/dpaa2/dpaa2-eth.c index 2c6f9b1..5402867 100644 --- a/drivers/net/ethernet/freescale/dpaa2/dpaa2-eth.c +++ b/drivers/net/ethernet/freescale/dpaa2/dpaa2-eth.c @@ -1208,9 +1208,37 @@ static void disable_ch_napi(struct dpaa2_eth_priv *priv) } } +static void dpaa2_eth_set_rx_taildrop(struct dpaa2_eth_priv *priv, bool enable) +{ + struct dpni_taildrop td = {0}; + int i, err; + + if (priv->rx_td_enabled == enable) + return; + + td.enable = enable; + td.threshold = DPAA2_ETH_TAILDROP_THRESH; + + for (i = 0; i < priv->num_fqs; i++) { + if (priv->fq[i].type != DPAA2_RX_FQ) + continue; + err = dpni_set_taildrop(priv->mc_io, 0, priv->mc_token, + DPNI_CP_QUEUE, DPNI_QUEUE_RX, 0, + priv->fq[i].flowid, &td); + if (err) { + netdev_err(priv->net_dev, + "dpni_set_taildrop() failed\n"); + break; + } + } + + priv->rx_td_enabled = enable; +} + static int link_state_update(struct dpaa2_eth_priv *priv) { struct dpni_link_state state = {0}; + bool tx_pause; int err; err = dpni_get_link_state(priv->mc_io, 0, priv->mc_token, &state); @@ -1220,6 +1248,14 @@ static int link_state_update(struct dpaa2_eth_priv *priv) return err; } + /* If Tx pause frame settings have changed, we need to update + * Rx FQ taildrop configuration as well. We configure taildrop + * only when pause frame generation is disabled. + */ + tx_pause = !!(state.options & DPNI_LINK_OPT_PAUSE) ^ + !!(state.options & DPNI_LINK_OPT_ASYM_PAUSE); + dpaa2_eth_set_rx_taildrop(priv, !tx_pause); + /* Chech link state; speed / duplex changes are not treated yet */ if (priv->link_state.up == state.up) goto out; @@ -2445,6 +2481,33 @@ static void set_enqueue_mode(struct dpaa2_eth_priv *priv) priv->enqueue = dpaa2_eth_enqueue_fq; } +static int set_pause(struct dpaa2_eth_priv *priv) +{ + struct device *dev = priv->net_dev->dev.parent; + struct dpni_link_cfg link_cfg = {0}; + int err; + + /* Get the default link options so we don't override other flags */ + err = dpni_get_link_cfg(priv->mc_io, 0, priv->mc_token, &link_cfg); + if (err) { + dev_err(dev, "dpni_get_link_cfg() failed\n"); + return err; + } + + /* By default, enable both Rx and Tx pause frames */ + link_cfg.options |= DPNI_LINK_OPT_PAUSE; + link_cfg.options &= ~DPNI_LINK_OPT_ASYM_PAUSE; + err = dpni_set_link_cfg(priv->mc_io, 0, priv->mc_token, &link_cfg); + if (err) { + dev_err(dev, "dpni_set_link_cfg() failed\n"); + return err; + } + + priv->link_state.options = link_cfg.options; + + return 0; +} + /* Configure the DPNI object this interface is associated with */ static int setup_dpni(struct fsl_mc_device *ls_dev) { @@ -2500,6 +2563,13 @@ static int setup_dpni(struct fsl_mc_device *ls_dev) set_enqueue_mode(priv); + /* Enable pause frame support */ + if (dpaa2_eth_has_pause_support(priv)) { + err = set_pause(priv); + if (err) + goto close; + } + priv->cls_rules = devm_kzalloc(dev, sizeof(struct dpaa2_eth_cls_rule) * dpaa2_eth_fs_count(priv), GFP_KERNEL); if (!priv->cls_rules) @@ -2531,7 +2601,6 @@ static int setup_rx_flow(struct dpaa2_eth_priv *priv, struct device *dev = priv->net_dev->dev.parent; struct dpni_queue queue; struct dpni_queue_id qid; - struct dpni_taildrop td; int err; err = dpni_get_queue(priv->mc_io, 0, priv->mc_token, @@ -2556,15 +2625,6 @@ static int setup_rx_flow(struct dpaa2_eth_priv *priv, return err; } - td.enable = 1; - td.threshold = DPAA2_ETH_TAILDROP_THRESH; - err = dpni_set_taildrop(priv->mc_io, 0, priv->mc_token, DPNI_CP_QUEUE, - DPNI_QUEUE_RX, 0, fq->flowid, &td); - if (err) { - dev_err(dev, "dpni_set_threshold() failed\n"); - return err; - } - /* xdp_rxq setup */ err = xdp_rxq_info_reg(&fq->channel->xdp_rxq, priv->net_dev, fq->flowid); diff --git a/drivers/net/ethernet/freescale/dpaa2/dpaa2-eth.h b/drivers/net/ethernet/freescale/dpaa2/dpaa2-eth.h index 9af18c2..8a0e65b 100644 --- a/drivers/net/ethernet/freescale/dpaa2/dpaa2-eth.h +++ b/drivers/net/ethernet/freescale/dpaa2/dpaa2-eth.h @@ -392,6 +392,7 @@ struct dpaa2_eth_priv { struct dpaa2_eth_drv_stats __percpu *percpu_extras; u16 mc_token; + u8 rx_td_enabled; struct dpni_link_state link_state; bool do_link_poll; @@ -476,6 +477,12 @@ enum dpaa2_eth_rx_dist { #define DPAA2_ETH_DIST_L4DST BIT(8) #define DPAA2_ETH_DIST_ALL (~0ULL) +#define DPNI_PAUSE_VER_MAJOR 7 +#define DPNI_PAUSE_VER_MINOR 13 +#define dpaa2_eth_has_pause_support(priv) \ + (dpaa2_eth_cmp_dpni_ver((priv), DPNI_PAUSE_VER_MAJOR, \ + DPNI_PAUSE_VER_MINOR) >= 0) + static inline unsigned int dpaa2_eth_needed_headroom(struct dpaa2_eth_priv *priv, struct sk_buff *skb) diff --git a/drivers/net/ethernet/freescale/dpaa2/dpaa2-ethtool.c b/drivers/net/ethernet/freescale/dpaa2/dpaa2-ethtool.c index fb17042..93076fe 100644 --- a/drivers/net/ethernet/freescale/dpaa2/dpaa2-ethtool.c +++ b/drivers/net/ethernet/freescale/dpaa2/dpaa2-ethtool.c @@ -88,6 +88,59 @@ dpaa2_eth_get_link_ksettings(struct net_device *net_dev, return 0; } +static void dpaa2_eth_get_pauseparam(struct net_device *net_dev, + struct ethtool_pauseparam *pause) +{ + struct dpaa2_eth_priv *priv = netdev_priv(net_dev); + u64 link_options = priv->link_state.options; + + pause->rx_pause = !!(link_options & DPNI_LINK_OPT_PAUSE); + pause->tx_pause = pause->rx_pause ^ + !!(link_options & DPNI_LINK_OPT_ASYM_PAUSE); + pause->autoneg = AUTONEG_DISABLE; +} + +static int dpaa2_eth_set_pauseparam(struct net_device *net_dev, + struct ethtool_pauseparam *pause) +{ + struct dpaa2_eth_priv *priv = netdev_priv(net_dev); + struct dpni_link_cfg cfg = {0}; + int err; + + if (!dpaa2_eth_has_pause_support(priv)) { + netdev_info(net_dev, "No pause frame support for DPNI version < %d.%d\n", + DPNI_PAUSE_VER_MAJOR, DPNI_PAUSE_VER_MINOR); + return -EOPNOTSUPP; + } + + if (pause->autoneg) + return -EOPNOTSUPP; + + cfg.rate = priv->link_state.rate; + cfg.options = priv->link_state.options; + if (pause->rx_pause) + cfg.options |= DPNI_LINK_OPT_PAUSE; + else + cfg.options &= ~DPNI_LINK_OPT_PAUSE; + if (!!pause->rx_pause ^ !!pause->tx_pause) + cfg.options |= DPNI_LINK_OPT_ASYM_PAUSE; + else + cfg.options &= ~DPNI_LINK_OPT_ASYM_PAUSE; + + if (cfg.options == priv->link_state.options) + return 0; + + err = dpni_set_link_cfg(priv->mc_io, 0, priv->mc_token, &cfg); + if (err) { + netdev_err(net_dev, "dpni_set_link_state failed\n"); + return err; + } + + priv->link_state.options = cfg.options; + + return 0; +} + static void dpaa2_eth_get_strings(struct net_device *netdev, u32 stringset, u8 *data) { @@ -664,6 +717,8 @@ const struct ethtool_ops dpaa2_ethtool_ops = { .get_drvinfo = dpaa2_eth_get_drvinfo, .get_link = ethtool_op_get_link, .get_link_ksettings = dpaa2_eth_get_link_ksettings, + .get_pauseparam = dpaa2_eth_get_pauseparam, + .set_pauseparam = dpaa2_eth_set_pauseparam, .get_sset_count = dpaa2_eth_get_sset_count, .get_ethtool_stats = dpaa2_eth_get_ethtool_stats, .get_strings = dpaa2_eth_get_strings, diff --git a/drivers/net/ethernet/freescale/dpaa2/dpni-cmd.h b/drivers/net/ethernet/freescale/dpaa2/dpni-cmd.h index 7b44d7d..d9b6918 100644 --- a/drivers/net/ethernet/freescale/dpaa2/dpni-cmd.h +++ b/drivers/net/ethernet/freescale/dpaa2/dpni-cmd.h @@ -84,6 +84,7 @@ #define DPNI_CMDID_SET_RX_FS_DIST DPNI_CMD(0x273) #define DPNI_CMDID_SET_RX_HASH_DIST DPNI_CMD(0x274) +#define DPNI_CMDID_GET_LINK_CFG DPNI_CMD(0x278) /* Macros for accessing command fields smaller than 1byte */ #define DPNI_MASK(field) \ @@ -284,7 +285,7 @@ struct dpni_rsp_get_statistics { __le64 counter[DPNI_STATISTICS_CNT]; }; -struct dpni_cmd_set_link_cfg { +struct dpni_cmd_link_cfg { /* cmd word 0 */ __le64 pad0; /* cmd word 1 */ diff --git a/drivers/net/ethernet/freescale/dpaa2/dpni.c b/drivers/net/ethernet/freescale/dpaa2/dpni.c index 220dfc8..05e3089 100644 --- a/drivers/net/ethernet/freescale/dpaa2/dpni.c +++ b/drivers/net/ethernet/freescale/dpaa2/dpni.c @@ -838,13 +838,13 @@ int dpni_set_link_cfg(struct fsl_mc_io *mc_io, const struct dpni_link_cfg *cfg) { struct fsl_mc_command cmd = { 0 }; - struct dpni_cmd_set_link_cfg *cmd_params; + struct dpni_cmd_link_cfg *cmd_params; /* prepare command */ cmd.header = mc_encode_cmd_header(DPNI_CMDID_SET_LINK_CFG, cmd_flags, token); - cmd_params = (struct dpni_cmd_set_link_cfg *)cmd.params; + cmd_params = (struct dpni_cmd_link_cfg *)cmd.params; cmd_params->rate = cpu_to_le32(cfg->rate); cmd_params->options = cpu_to_le64(cfg->options); @@ -853,6 +853,42 @@ int dpni_set_link_cfg(struct fsl_mc_io *mc_io, } /** + * dpni_get_link_cfg() - return the link configuration + * @mc_io: Pointer to MC portal's I/O object + * @cmd_flags: Command flags; one or more of 'MC_CMD_FLAG_' + * @token: Token of DPNI object + * @cfg: Link configuration from dpni object + * + * Return: '0' on Success; Error code otherwise. + */ +int dpni_get_link_cfg(struct fsl_mc_io *mc_io, + u32 cmd_flags, + u16 token, + struct dpni_link_cfg *cfg) +{ + struct fsl_mc_command cmd = { 0 }; + struct dpni_cmd_link_cfg *rsp_params; + int err; + + /* prepare command */ + cmd.header = mc_encode_cmd_header(DPNI_CMDID_GET_LINK_CFG, + cmd_flags, + token); + + /* send command to mc*/ + err = mc_send_command(mc_io, &cmd); + if (err) + return err; + + /* retrieve response parameters */ + rsp_params = (struct dpni_cmd_link_cfg *)cmd.params; + cfg->rate = le32_to_cpu(rsp_params->rate); + cfg->options = le64_to_cpu(rsp_params->options); + + return err; +} + +/** * dpni_get_link_state() - Return the link state (either up or down) * @mc_io: Pointer to MC portal's I/O object * @cmd_flags: Command flags; one or more of 'MC_CMD_FLAG_' diff --git a/drivers/net/ethernet/freescale/dpaa2/dpni.h b/drivers/net/ethernet/freescale/dpaa2/dpni.h index a521242..3e8fc6c 100644 --- a/drivers/net/ethernet/freescale/dpaa2/dpni.h +++ b/drivers/net/ethernet/freescale/dpaa2/dpni.h @@ -485,6 +485,11 @@ int dpni_set_link_cfg(struct fsl_mc_io *mc_io, u16 token, const struct dpni_link_cfg *cfg); +int dpni_get_link_cfg(struct fsl_mc_io *mc_io, + u32 cmd_flags, + u16 token, + struct dpni_link_cfg *cfg); + /** * struct dpni_link_state - Structure representing DPNI link state * @rate: Rate -- 2.7.4