From 75f2d3eac93277fa022b2fbe51257e856575e757 Mon Sep 17 00:00:00 2001 From: Ben Hutchings Date: Wed, 7 May 2008 12:55:13 +0100 Subject: [PATCH] [netdrvr] sfc: Add phy_flash_cfg module parameter and implementation The 10Xpress PHY supports flash upgrades through MDIO, but needs to be put in upgrade mode at power-up. This adds a module parameter and other logic to support that. Signed-off-by: Ben Hutchings Signed-off-by: Jeff Garzik --- drivers/net/sfc/boards.h | 2 ++ drivers/net/sfc/falcon_xmac.c | 4 ++++ drivers/net/sfc/sfe4001.c | 14 ++++++++++++++ drivers/net/sfc/tenxpress.c | 10 ++++++---- 4 files changed, 26 insertions(+), 4 deletions(-) diff --git a/drivers/net/sfc/boards.h b/drivers/net/sfc/boards.h index f56341d..695764d 100644 --- a/drivers/net/sfc/boards.h +++ b/drivers/net/sfc/boards.h @@ -22,5 +22,7 @@ enum efx_board_type { extern int efx_set_board_info(struct efx_nic *efx, u16 revision_info); extern int sfe4001_poweron(struct efx_nic *efx); extern void sfe4001_poweroff(struct efx_nic *efx); +/* Are we putting the PHY into flash config mode */ +extern unsigned int sfe4001_phy_flash_cfg; #endif diff --git a/drivers/net/sfc/falcon_xmac.c b/drivers/net/sfc/falcon_xmac.c index aa7521b..d99efe2 100644 --- a/drivers/net/sfc/falcon_xmac.c +++ b/drivers/net/sfc/falcon_xmac.c @@ -69,6 +69,10 @@ static int falcon_reset_xmac(struct efx_nic *efx) udelay(10); } + /* This often fails when DSP is disabled, ignore it */ + if (sfe4001_phy_flash_cfg != 0) + return 0; + EFX_ERR(efx, "timed out waiting for XMAC core reset\n"); return -ETIMEDOUT; } diff --git a/drivers/net/sfc/sfe4001.c b/drivers/net/sfc/sfe4001.c index 11fa9fb..725d1a5 100644 --- a/drivers/net/sfc/sfe4001.c +++ b/drivers/net/sfc/sfe4001.c @@ -130,6 +130,15 @@ void sfe4001_poweroff(struct efx_nic *efx) (void) efx_i2c_read(i2c, MAX6647, RSL, &in, 1); } +/* The P0_EN_3V3X line on SFE4001 boards (from A2 onward) is connected + * to the FLASH_CFG_1 input on the DSP. We must keep it high at power- + * up to allow writing the flash (done through MDIO from userland). + */ +unsigned int sfe4001_phy_flash_cfg; +module_param_named(phy_flash_cfg, sfe4001_phy_flash_cfg, uint, 0444); +MODULE_PARM_DESC(phy_flash_cfg, + "Force PHY to enter flash configuration mode"); + /* This board uses an I2C expander to provider power to the PHY, which needs to * be turned on before the PHY can be used. * Context: Process context, rtnl lock held @@ -203,6 +212,8 @@ int sfe4001_poweron(struct efx_nic *efx) out = 0xff & ~((1 << P0_EN_1V2_LBN) | (1 << P0_EN_2V5_LBN) | (1 << P0_EN_3V3X_LBN) | (1 << P0_EN_5V_LBN) | (1 << P0_X_TRST_LBN)); + if (sfe4001_phy_flash_cfg) + out |= 1 << P0_EN_3V3X_LBN; rc = efx_i2c_write(i2c, PCA9539, P0_OUT, &out, 1); if (rc) @@ -226,6 +237,9 @@ int sfe4001_poweron(struct efx_nic *efx) if (in & (1 << P1_AFE_PWD_LBN)) goto done; + /* DSP doesn't look powered in flash config mode */ + if (sfe4001_phy_flash_cfg) + goto done; } while (++count < 20); EFX_INFO(efx, "timed out waiting for power\n"); diff --git a/drivers/net/sfc/tenxpress.c b/drivers/net/sfc/tenxpress.c index a2e9f79..d8df031 100644 --- a/drivers/net/sfc/tenxpress.c +++ b/drivers/net/sfc/tenxpress.c @@ -199,10 +199,12 @@ static int tenxpress_phy_init(struct efx_nic *efx) tenxpress_set_state(efx, TENXPRESS_STATUS_NORMAL); - rc = mdio_clause45_wait_reset_mmds(efx, - TENXPRESS_REQUIRED_DEVS); - if (rc < 0) - goto fail; + if (!sfe4001_phy_flash_cfg) { + rc = mdio_clause45_wait_reset_mmds(efx, + TENXPRESS_REQUIRED_DEVS); + if (rc < 0) + goto fail; + } rc = mdio_clause45_check_mmds(efx, TENXPRESS_REQUIRED_DEVS, 0); if (rc < 0) -- 2.7.4