From 6bde1ec10ff438170721624ca87b86fd25669b3b Mon Sep 17 00:00:00 2001 From: Masahiro Yamada Date: Wed, 6 Aug 2014 12:59:54 +0900 Subject: [PATCH] powerpc: mpc8xx: remove GEN860T, GEN806T_SC board support These boards have been orphaned for a while and old enough. Signed-off-by: Masahiro Yamada --- arch/powerpc/cpu/mpc8xx/Kconfig | 4 - board/gen860t/Kconfig | 11 - board/gen860t/MAINTAINERS | 7 - board/gen860t/Makefile | 8 - board/gen860t/README | 131 ------- board/gen860t/beeper.c | 183 ---------- board/gen860t/beeper.h | 13 - board/gen860t/flash.c | 628 --------------------------------- board/gen860t/fpga.c | 362 ------------------- board/gen860t/fpga.h | 26 -- board/gen860t/gen860t.c | 278 --------------- board/gen860t/ioport.c | 331 ------------------ board/gen860t/ioport.h | 26 -- board/gen860t/u-boot-flashenv.lds | 92 ----- board/gen860t/u-boot.lds | 87 ----- configs/GEN860T_SC_defconfig | 4 - configs/GEN860T_defconfig | 3 - doc/README.scrapyard | 1 + include/commproc.h | 21 -- include/configs/GEN860T.h | 712 -------------------------------------- include/status_led.h | 24 -- 21 files changed, 1 insertion(+), 2951 deletions(-) delete mode 100644 board/gen860t/Kconfig delete mode 100644 board/gen860t/MAINTAINERS delete mode 100644 board/gen860t/Makefile delete mode 100644 board/gen860t/README delete mode 100644 board/gen860t/beeper.c delete mode 100644 board/gen860t/beeper.h delete mode 100644 board/gen860t/flash.c delete mode 100644 board/gen860t/fpga.c delete mode 100644 board/gen860t/fpga.h delete mode 100644 board/gen860t/gen860t.c delete mode 100644 board/gen860t/ioport.c delete mode 100644 board/gen860t/ioport.h delete mode 100644 board/gen860t/u-boot-flashenv.lds delete mode 100644 board/gen860t/u-boot.lds delete mode 100644 configs/GEN860T_SC_defconfig delete mode 100644 configs/GEN860T_defconfig delete mode 100644 include/configs/GEN860T.h diff --git a/arch/powerpc/cpu/mpc8xx/Kconfig b/arch/powerpc/cpu/mpc8xx/Kconfig index f9e7472..d5cec1f 100644 --- a/arch/powerpc/cpu/mpc8xx/Kconfig +++ b/arch/powerpc/cpu/mpc8xx/Kconfig @@ -17,9 +17,6 @@ config TARGET_ESTEEM192E config TARGET_FLAGADM bool "Support FLAGADM" -config TARGET_GEN860T - bool "Support GEN860T" - config TARGET_HERMES bool "Support hermes" @@ -131,7 +128,6 @@ source "board/eltec/mhpc/Kconfig" source "board/emk/top860/Kconfig" source "board/esteem192e/Kconfig" source "board/flagadm/Kconfig" -source "board/gen860t/Kconfig" source "board/hermes/Kconfig" source "board/icu862/Kconfig" source "board/ip860/Kconfig" diff --git a/board/gen860t/Kconfig b/board/gen860t/Kconfig deleted file mode 100644 index 438f7cc..0000000 --- a/board/gen860t/Kconfig +++ /dev/null @@ -1,11 +0,0 @@ -if TARGET_GEN860T - -config SYS_BOARD - string - default "gen860t" - -config SYS_CONFIG_NAME - string - default "GEN860T" - -endif diff --git a/board/gen860t/MAINTAINERS b/board/gen860t/MAINTAINERS deleted file mode 100644 index c5d3da3..0000000 --- a/board/gen860t/MAINTAINERS +++ /dev/null @@ -1,7 +0,0 @@ -GEN860T BOARD -M: Keith Outwater -S: Orphan (since 2014-06) -F: board/gen860t/ -F: include/configs/GEN860T.h -F: configs/GEN860T_defconfig -F: configs/GEN860T_SC_defconfig diff --git a/board/gen860t/Makefile b/board/gen860t/Makefile deleted file mode 100644 index 86ae5e8..0000000 --- a/board/gen860t/Makefile +++ /dev/null @@ -1,8 +0,0 @@ -# -# (C) Copyright 2000-2006 -# Wolfgang Denk, DENX Software Engineering, wd@denx.de. -# -# SPDX-License-Identifier: GPL-2.0+ -# - -obj-y = gen860t.o flash.o beeper.o fpga.o ioport.o diff --git a/board/gen860t/README b/board/gen860t/README deleted file mode 100644 index 3ef8ae1..0000000 --- a/board/gen860t/README +++ /dev/null @@ -1,131 +0,0 @@ -This directory contains board specific code for a generic MPC860T based -embedded computer, called 'GEN860T'. The design is generic in the sense that -common, readily available components are used and that the architecture of the -system is relatively straightforward: - - One eight bit wide boot (FLASH) memory - 32 bit main memory using SDRAM - DOC 2000+ - Ethernet PHY - Some I2C peripheral devices: Atmel AT24C256 EEPROM, Maxim DS1337 RTC. - Some other miscellaneous peripherals - -NOTE: There are references to a XIlinx FPGA and Mil-Std 1553 databus in this -port. I guess the computer is not as generic as I first said 8) However, -these extras can be safely ignored. - -Given the GEN860T files, it should be pretty easy to reverse engineer the -hardware configuration, if that's useful to you. Hopefully, this code will -be useful to someone as a basis for a port to a new system or as a head start -on a custom design. If you end up using any of this, I would appreciate -hearing from you, especially if you discover bugs or find ways to improve the -quality of this U-Boot port. - -Here are the salient features of the system: -Clock : 33.3 Mhz oscillator -Processor core frequency : 66.6 Mhz if in 1:2:1 mode; can also run 1:1 -Bus frequency : 33.3 Mhz - -Main memory: - Type : SDRAM - Width : 32 bits - Size : 64 mibibytes - Chip : Two Micron MT48LC16M16A2TG-7E - CS : MPC860T CS1*/UPMA - UPMA CONNECTIONS: - SDRAM A10 : GPLA0* - SDRAM CAS* : GPLA2* - SDRAM WE* : GPLA3* - SDRAM RAS* : GPLA4* - -Boot memory: - Type : FLASH - Width : 8 bits - Size : 16 mibibytes - Chip : One Intel 28F128J3A (StrataFlash) - CS : MPC860T CS0*/GPCM (this is the "boot" chip select) - -EEPROM memory: - Type : Serial I2C EEPROM - Width : 8 bits - Size : 32 kibibytes - Chip : One Atmel AT25C256 - CS : 0x50 (external I2C address pins on device are tied to GND) - -Filesystem memory: - Type : NAND FLASH (Toshiba) - Width : 8 bits (i.e. interface to DOC is 8 bits) - Size : 32 mibibytes - Chip : One DiskOnCHip Millenium Plus (DOC 2000+) - CS : MPC860T CS2*/GPCM - -Network support: - MAC : MPC86OT FEC (Fast Ethernet Controller) - PHY : Intel LXT971A - MII Addr: 0x0 (hardwired on the board) - MII IRQ : - -Console: - RS-232 on SMC1 (Maxim MAX3232 LVCMOS-RS232 level shifter) - -Real Time Clock: - Type : Low power, I2C interface - Chip : Maxim DS1337 - CS : Address 0x68 on I2C bus - - The MPC860T's internal RTC has a defect in Mask rev D that increases - the current drain on the KAPWR line to 10 mA. Since this is an - unreasonable amount of current draw for a RTC, and Motorola does not - plan to fix this in future mask revisions, a serial (I2C) RTC that - works has been included instead. NOTE that the DS1337 can be - configured to output a 32768 Hz clock while the main power is on. - This clock output has been routed to the MPC860T's EXTAL pin to allow - the internal RTC to be used. NOTE also that due to yet another - defect in the rev D mask, the RTC does not operate reliably when the - internal RTC divisor is set to use a 32768 Hz reference. So just use - the I2C RTC. - -Miscellaneous: - Xilinx Virtex FPGA on CS3*/GPCM. - Virtex FPGA slave SelectMap interface on cs4*/UPMB. - Mil-Std 1553 databus interface on CS5*/GPCM. - Audio sounder (beeper) with digital volume control connected to SPKROUT. - -SC variant: - A reduced-feature version of the GEN860T port is also supported: GEN860T_SC. - The 'SC' variant only provides support for the Virtex FPGA, SDRAM main - memory, EEPROM and flash memory. The system clock frequency is reduced - to 24 MHz. - -Issues: - The DOC 2000+ returns 0x40 as its device ID when probed using the method - desxribed in the DOC datasheet. Unfortunately, the U-Boot DOC driver - does not recognize this device. As of this writing, it seems that MTD - does not support the DOC 2000+ either. - -Status: - Everything appears to work except DOC support. As of this writing, - David Woodhouse has stated on the MTD mailing list that he has no - knowledge of the DOC Millineum Plus and therfore there is no support - in MTD for this device. I wish I had known this sooner :( - -The GEN860T board specific files and configuration is based on the work -of others who have contributed to U-Boot. The copyright and license notices -of these authors have been retained wherever their code has been reused. -All new code to support the GEN860T board is: - - (C) Copyright 2001-2003 - Keith Outwater (keith_outwater@mvis.com) - -and the following license applies: - -SPDX-License-Identifier: GPL-2.0+ - -Thanks to Wolfgang Denk for a great software package and to everyone -who contributed to its development. - -Keith Outwater -Sr. Staff Engineer -Microvision, Inc. - - diff --git a/board/gen860t/beeper.c b/board/gen860t/beeper.c deleted file mode 100644 index 0bebca9..0000000 --- a/board/gen860t/beeper.c +++ /dev/null @@ -1,183 +0,0 @@ -/* - * (C) Copyright 2002 - * Keith Outwater, keith_outwater@mvis.com - * - * SPDX-License-Identifier: GPL-2.0+ - */ - -#include -#include -#include -#include - -/* - * Basic beeper support for the GEN860T board. The GEN860T includes - * an audio sounder driven by a Phillips TDA8551 amplifier. The - * TDA8551 features a digital volume control which uses a "trinary" - * input (high/high-Z/low) to set volume. The 860's SPKROUT pin - * drives the amplifier input. - */ - -/* - * Initialize beeper-related hardware. Initialize timer 1 for use with - * the beeper. Use 66 MHz internal clock with prescale of 33 to get - * 1 uS period per count. - * FIXME: we should really compute the prescale based on the reported - * core clock frequency. - */ -void init_beeper (void) -{ - volatile immap_t *immap = (immap_t *) CONFIG_SYS_IMMR; - - immap->im_cpmtimer.cpmt_tgcr &= ~TGCR_RST1 | TGCR_STP1; - immap->im_cpmtimer.cpmt_tmr1 = ((33 << TMR_PS_SHIFT) & TMR_PS_MSK) - | TMR_OM | TMR_FRR | TMR_ICLK_IN_GEN; - immap->im_cpmtimer.cpmt_tcn1 = 0; - immap->im_cpmtimer.cpmt_ter1 = 0xffff; - immap->im_cpmtimer.cpmt_tgcr |= TGCR_RST1; -} - -/* - * Set beeper frequency. Max allowed frequency is 2.5 KHz. This limit - * is mostly arbitrary, but the beeper isn't really much good beyond this - * frequency. - */ -void set_beeper_frequency (uint frequency) -{ -#define FREQ_LIMIT 2500 - - volatile immap_t *immap = (immap_t *) CONFIG_SYS_IMMR; - - /* - * Compute timer ticks given desired frequency. The timer is set up - * to count 0.5 uS per tick and it takes two ticks per cycle (Hz). - */ - if (frequency > FREQ_LIMIT) - frequency = FREQ_LIMIT; - frequency = 1000000 / frequency; - immap->im_cpmtimer.cpmt_trr1 = (ushort) frequency; -} - -/* - * Turn the beeper on - */ -void beeper_on (void) -{ - volatile immap_t *immap = (immap_t *) CONFIG_SYS_IMMR; - - immap->im_cpmtimer.cpmt_tgcr &= ~TGCR_STP1; -} - -/* - * Turn the beeper off - */ -void beeper_off (void) -{ - volatile immap_t *immap = (immap_t *) CONFIG_SYS_IMMR; - - immap->im_cpmtimer.cpmt_tgcr |= TGCR_STP1; -} - -/* - * Increase or decrease the beeper volume. Volume can be set - * from off to full in 64 steps. To increase volume, the output - * pin is actively driven high, then returned to tristate. - * To decrease volume, output a low on the port pin (no need to - * change pin mode to tristate) then output a high to go back to - * tristate. - */ -void set_beeper_volume (int steps) -{ - volatile immap_t *immap = (immap_t *) CONFIG_SYS_IMMR; - int i; - - if (steps >= 0) { - for (i = 0; i < (steps >= 64 ? 64 : steps); i++) { - immap->im_cpm.cp_pbodr &= ~(0x80000000 >> 19); - udelay (1); - immap->im_cpm.cp_pbodr |= (0x80000000 >> 19); - udelay (1); - } - } else { - for (i = 0; i > (steps <= -64 ? -64 : steps); i--) { - immap->im_cpm.cp_pbdat &= ~(0x80000000 >> 19); - udelay (1); - immap->im_cpm.cp_pbdat |= (0x80000000 >> 19); - udelay (1); - } - } -} - -/* - * Check the environment to see if the beeper needs beeping. - * Controlled by a sequence of the form: - * freq/delta volume/on time/off time;... where: - * freq = frequency in Hz (0 - 2500) - * delta volume = volume steps up or down (-64 <= vol <= 64) - * on time = time in mS - * off time = time in mS - * - * Return 1 on success, 0 on failure - */ -int do_beeper (char *sequence) -{ -#define DELIMITER ';' - - int args[4]; - int i; - int val; - char *p = sequence; - char *tp; - - /* - * Parse the control sequence. This is a really simple parser - * without any real error checking. You can probably blow it - * up really easily. - */ - if (*p == '\0' || !isdigit (*p)) { - printf ("%s:%d: null or invalid string (%s)\n", - __FILE__, __LINE__, p); - return 0; - } - - i = 0; - while (*p != '\0') { - while (*p != DELIMITER) { - if (i > 3) - i = 0; - val = (int) simple_strtol (p, &tp, 0); - if (tp == p) { - printf ("%s:%d: no digits or bad format\n", - __FILE__, __LINE__); - return 0; - } else { - args[i] = val; - } - - i++; - if (*tp == DELIMITER) - p = tp; - else - p = ++tp; - } - p++; - - /* - * Well, we got something that has a chance of being correct - */ -#if 0 - for (i = 0; i < 4; i++) { - printf ("%s:%d:arg %d = %d\n", __FILE__, __LINE__, i, - args[i]); - } - printf ("\n"); -#endif - set_beeper_frequency (args[0]); - set_beeper_volume (args[1]); - beeper_on (); - udelay (1000 * args[2]); - beeper_off (); - udelay (1000 * args[3]); - } - return 1; -} diff --git a/board/gen860t/beeper.h b/board/gen860t/beeper.h deleted file mode 100644 index 0734fca..0000000 --- a/board/gen860t/beeper.h +++ /dev/null @@ -1,13 +0,0 @@ -/* - * (C) Copyright 2002 - * Keith Outwater, keith_outwater@mvis.com - * - * SPDX-License-Identifier: GPL-2.0+ - */ - -void init_beeper(void); -void set_beeper_frequency(uint frequency); -void beeper_on(void); -void beeper_off(void); -void set_beeper_volume(int steps); -int do_beeper(char *sequence); diff --git a/board/gen860t/flash.c b/board/gen860t/flash.c deleted file mode 100644 index ca1ed3d..0000000 --- a/board/gen860t/flash.c +++ /dev/null @@ -1,628 +0,0 @@ -/* - * (C) Copyright 2001 - * Wolfgang Denk, DENX Software Engineering, wd@denx.de. - * Keith Outwater, keith_outwater@mvsi.com - * - * SPDX-License-Identifier: GPL-2.0+ - */ - -#include -#include - -#if defined(CONFIG_ENV_IS_IN_FLASH) -# ifndef CONFIG_ENV_ADDR -# define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + CONFIG_ENV_OFFSET) -# endif -# ifndef CONFIG_ENV_SIZE -# define CONFIG_ENV_SIZE CONFIG_ENV_SECT_SIZE -# endif -# ifndef CONFIG_ENV_SECT_SIZE -# define CONFIG_ENV_SECT_SIZE CONFIG_ENV_SIZE -# endif -#endif - -/* - * Use buffered writes to flash by default - they are about 32x faster than - * single byte writes. - */ -#ifndef CONFIG_SYS_GEN860T_FLASH_USE_WRITE_BUFFER -#define CONFIG_SYS_GEN860T_FLASH_USE_WRITE_BUFFER -#endif - -/* - * Max time to wait (in mS) for flash device to allocate a write buffer. - */ -#ifndef CONFIG_SYS_FLASH_ALLOC_BUFFER_TOUT -#define CONFIG_SYS_FLASH_ALLOC_BUFFER_TOUT 100 -#endif - -/* - * These functions support a single Intel StrataFlash device (28F128J3A) - * in byte mode only!. The flash routines are very basic and simple - * since there isn't really any remapping necessary. - */ - -/* - * Intel SCS (Scalable Command Set) command definitions - * (taken from 28F128J3A datasheet) - */ -#define SCS_READ_CMD 0xff -#define SCS_READ_ID_CMD 0x90 -#define SCS_QUERY_CMD 0x98 -#define SCS_READ_STATUS_CMD 0x70 -#define SCS_CLEAR_STATUS_CMD 0x50 -#define SCS_WRITE_BUF_CMD 0xe8 -#define SCS_PROGRAM_CMD 0x40 -#define SCS_BLOCK_ERASE_CMD 0x20 -#define SCS_BLOCK_ERASE_RESUME_CMD 0xd0 -#define SCS_PROGRAM_RESUME_CMD 0xd0 -#define SCS_BLOCK_ERASE_SUSPEND_CMD 0xb0 -#define SCS_SET_BLOCK_LOCK_CMD 0x60 -#define SCS_CLR_BLOCK_LOCK_CMD 0x60 - -/* - * SCS status/extended status register bit definitions - */ -#define SCS_SR7 0x80 -#define SCS_XSR7 0x80 - -/*---------------------------------------------------------------------*/ -#if 0 -#define DEBUG_FLASH -#endif - -#ifdef DEBUG_FLASH -#define PRINTF(fmt,args...) printf(fmt ,##args) -#else -#define PRINTF(fmt,args...) -#endif -/*---------------------------------------------------------------------*/ - -flash_info_t flash_info[CONFIG_SYS_MAX_FLASH_BANKS]; - -/*----------------------------------------------------------------------- - * Functions - */ -static ulong flash_get_size (vu_char *addr, flash_info_t *info); -static int write_data8 (flash_info_t *info, ulong dest, uchar data); -static void flash_get_offsets (ulong base, flash_info_t *info); - -/*----------------------------------------------------------------------- - * Initialize the flash memory. - */ -unsigned long -flash_init (void) -{ - volatile immap_t *immap = (immap_t *)CONFIG_SYS_IMMR; - volatile memctl8xx_t *memctl = &immap->im_memctl; - unsigned long size_b0; - int i; - - for (i= 0; i < CONFIG_SYS_MAX_FLASH_BANKS; ++i) { - flash_info[i].flash_id = FLASH_UNKNOWN; - } - - /* - * The gen860t board only has one FLASH memory device, so the - * FLASH Bank configuration is done statically. - */ - PRINTF("\n## Get flash bank 1 size @ 0x%08x\n", FLASH_BASE0_PRELIM); - size_b0 = flash_get_size((vu_char *)FLASH_BASE0_PRELIM, &flash_info[0]); - if (flash_info[0].flash_id == FLASH_UNKNOWN) { - printf ("## Unknown FLASH on Bank 0: " - "ID 0x%lx, Size = 0x%08lx = %ld MB\n", - flash_info[0].flash_id,size_b0, size_b0 << 20); - } - - PRINTF("## Before remap:\n" - " BR0: 0x%08x OR0: 0x%08x\n BR1: 0x%08x OR1: 0x%08x\n", - memctl->memc_br0, memctl->memc_or0, - memctl->memc_br1, memctl->memc_or1); - - /* - * Remap FLASH according to real size - */ - memctl->memc_or0 |= (-size_b0 & 0xFFFF8000); - memctl->memc_br0 |= (CONFIG_SYS_FLASH_BASE & BR_BA_MSK); - - PRINTF("## After remap:\n" - " BR0: 0x%08x OR0: 0x%08x\n", memctl->memc_br0, memctl->memc_or0); - - /* - * Re-do sizing to get full correct info - */ - size_b0 = flash_get_size ((vu_char *)CONFIG_SYS_FLASH_BASE, &flash_info[0]); - flash_get_offsets (CONFIG_SYS_FLASH_BASE, &flash_info[0]); - flash_info[0].size = size_b0; - -#if CONFIG_SYS_MONITOR_BASE >= CONFIG_SYS_FLASH_BASE - /* - * Monitor protection is ON by default - */ - flash_protect(FLAG_PROTECT_SET, - CONFIG_SYS_MONITOR_BASE, - CONFIG_SYS_MONITOR_BASE + monitor_flash_len - 1, - &flash_info[0]); -#endif - -#ifdef CONFIG_ENV_IS_IN_FLASH - /* - * Environment protection ON by default - */ - flash_protect(FLAG_PROTECT_SET, - CONFIG_ENV_ADDR, - CONFIG_ENV_ADDR + CONFIG_ENV_SECT_SIZE - 1, - &flash_info[0]); -#endif - - PRINTF("## Final Flash bank size: 0x%08lx\n",size_b0); - return (size_b0); -} - - -/*----------------------------------------------------------------------- - * Fill in the FLASH offset table - */ -static void -flash_get_offsets (ulong base, flash_info_t *info) -{ - int i; - - if (info->flash_id == FLASH_UNKNOWN) { - return; - } - - switch (info->flash_id & FLASH_VENDMASK) { - case FLASH_MAN_INTEL: - for (i = 0; i < info->sector_count; i++) { - info->start[i] = base; - base += 1024 * 128; - } - return; - - default: - printf ("Don't know sector offsets for FLASH" - " type 0x%lx\n", info->flash_id); - return; - } -} - - -/*----------------------------------------------------------------------- - * Display FLASH device info - */ -void -flash_print_info (flash_info_t *info) -{ - int i; - - if (info->flash_id == FLASH_UNKNOWN) { - printf ("Missing or unknown FLASH type\n"); - return; - } - - switch (info->flash_id & FLASH_VENDMASK) { - case FLASH_MAN_INTEL: - printf ("Intel "); - break; - default: - printf ("Unknown Vendor "); - break; - } - - switch (info->flash_id & FLASH_TYPEMASK) { - case FLASH_28F128J3A: - printf ("28F128J3A (128Mbit = 128K x 128)\n"); - break; - default: - printf ("Unknown Chip Type\n"); - break; - } - - if (info->size >= (1024 * 1024)) { - i = 20; - } else { - i = 10; - } - printf (" Size: %ld %cB in %d Sectors\n", - info->size >> i, - (i == 20) ? 'M' : 'k', - info->sector_count); - - printf (" Sector Start Addresses:"); - for (i=0; isector_count; ++i) { - if ((i % 5) == 0) - printf ("\n "); - printf (" %08lX%s", - info->start[i], - info->protect[i] ? " (RO)" : " " - ); - } - printf ("\n"); - return; -} - - -/*----------------------------------------------------------------------- - * Get size and other information for a FLASH device. - * NOTE: The following code cannot be run from FLASH! - */ -static -ulong flash_get_size (vu_char *addr, flash_info_t *info) -{ -#define NO_FLASH 0 - - vu_char value[2]; - - /* - * Try to read the manufacturer ID - */ - addr[0] = SCS_READ_CMD; - addr[0] = SCS_READ_ID_CMD; - value[0] = addr[0]; - value[1] = addr[2]; - addr[0] = SCS_READ_CMD; - - PRINTF("Manuf. ID @ 0x%08lx: 0x%02x\n", (ulong)addr, value[0]); - switch (value[0]) { - case (INTEL_MANUFACT & 0xff): - info->flash_id = FLASH_MAN_INTEL; - break; - default: - info->flash_id = FLASH_UNKNOWN; - info->sector_count = 0; - info->size = 0; - return (NO_FLASH); - } - - /* - * Read the device ID - */ - PRINTF("Device ID @ 0x%08lx: 0x%02x\n", (ulong)(&addr[2]), value[1]); - switch (value[1]) { - case (INTEL_ID_28F128J3A & 0xff): - info->flash_id += FLASH_28F128J3A; - info->sector_count = 128; - info->size = 16 * 1024 * 1024; - break; - - default: - info->flash_id = FLASH_UNKNOWN; - return (NO_FLASH); - } - - if (info->sector_count > CONFIG_SYS_MAX_FLASH_SECT) { - printf ("** ERROR: sector count %d > max (%d) **\n", - info->sector_count, CONFIG_SYS_MAX_FLASH_SECT); - info->sector_count = CONFIG_SYS_MAX_FLASH_SECT; - } - return (info->size); -} - - -/*----------------------------------------------------------------------- - * Erase the specified sectors in the specified FLASH device - */ -int -flash_erase(flash_info_t *info, int s_first, int s_last) -{ - int flag, prot, sect; - ulong start, now, last; - - if ((s_first < 0) || (s_first > s_last)) { - if (info->flash_id == FLASH_UNKNOWN) { - printf ("- missing\n"); - } else { - printf ("- no sectors to erase\n"); - } - return 1; - } - - if ((info->flash_id & FLASH_VENDMASK) != FLASH_MAN_INTEL) { - printf ("Can erase only Intel flash types - aborted\n"); - return 1; - } - - prot = 0; - for (sect=s_first; sect<=s_last; ++sect) { - if (info->protect[sect]) { - prot++; - } - } - - if (prot) { - printf ("- Warning: %d protected sectors will not be erased!\n", - prot); - } else { - printf ("\n"); - } - - start = get_timer (0); - last = start; - - /* - * Start erase on unprotected sectors - */ - for (sect = s_first; sect<=s_last; sect++) { - if (info->protect[sect] == 0) { /* not protected */ - vu_char *addr = (uchar *)(info->start[sect]); - vu_char status; - - /* - * Disable interrupts which might cause a timeout - */ - flag = disable_interrupts(); - - *addr = SCS_CLEAR_STATUS_CMD; - *addr = SCS_BLOCK_ERASE_CMD; - *addr = SCS_BLOCK_ERASE_RESUME_CMD; - - /* - * Re-enable interrupts if necessary - */ - if (flag) - enable_interrupts(); - - /* - * Wait at least 80us - let's wait 1 ms - */ - udelay (1000); - - while (((status = *addr) & SCS_SR7) != SCS_SR7) { - if ((now=get_timer(start)) > CONFIG_SYS_FLASH_ERASE_TOUT) { - printf ("Timeout\n"); - *addr = SCS_BLOCK_ERASE_SUSPEND_CMD; - *addr = SCS_READ_CMD; - return 1; - } - - /* - * Show that we're waiting - */ - if ((now - last) > 1000) { /* 1 second */ - putc ('.'); - last = now; - } - } - *addr = SCS_READ_CMD; - } - } - printf (" done\n"); - return 0; -} - - -#ifdef CONFIG_SYS_GEN860T_FLASH_USE_WRITE_BUFFER -/* - * Allocate a flash buffer, fill it with data and write it to the flash. - * 0 - OK - * 1 - Timeout on buffer request - * - * NOTE: After the last call to this function, WSM status needs to be checked! - */ -static int -write_flash_buffer8(flash_info_t *info_p, vu_char *src_p, vu_char *dest_p, - uint count) -{ - vu_char *block_addr_p = NULL; - vu_char *start_addr_p = NULL; - ulong blocksize = info_p->size / (ulong)info_p->sector_count; - - int i; - uint time = get_timer(0); - - PRINTF("%s:%d: src: 0x%p dest: 0x%p count: %d\n", - __FUNCTION__, __LINE__, src_p, dest_p, count); - - /* - * What block are we in? We already know that the source address is - * in the flash address range, but we also can't cross a block boundary. - * We assume that the block does not cross a boundary (we'll check before - * calling this function). - */ - for (i = 0; i < info_p->sector_count; ++i) { - if ( ((ulong)dest_p >= info_p->start[i]) && - ((ulong)dest_p < (info_p->start[i] + blocksize)) ) { - PRINTF("%s:%d: Dest addr 0x%p is in block %d @ 0x%.8lx\n", - __FUNCTION__, __LINE__, dest_p, i, info_p->start[i]); - block_addr_p = (vu_char *)info_p->start[i]; - break; - } - } - - /* - * Request a buffer - */ - *block_addr_p = SCS_WRITE_BUF_CMD; - while ((*block_addr_p & SCS_XSR7) != SCS_XSR7) { - if (get_timer(time) > CONFIG_SYS_FLASH_ALLOC_BUFFER_TOUT) { - PRINTF("%s:%d: Buffer allocation timeout @ 0x%p (waited %d mS)\n", - __FUNCTION__, __LINE__, block_addr_p, - CONFIG_SYS_FLASH_ALLOC_BUFFER_TOUT); - return 1; - } - *block_addr_p = SCS_WRITE_BUF_CMD; - } - - /* - * Fill the buffer with data - */ - start_addr_p = dest_p; - *block_addr_p = count - 1; /* flash device wants count - 1 */ - PRINTF("%s:%d: Fill buffer at block addr 0x%p\n", - __FUNCTION__, __LINE__, block_addr_p); - for (i = 0; i < count; i++) { - *start_addr_p++ = *src_p++; - } - - /* - * Flush buffer to flash - */ - *block_addr_p = SCS_PROGRAM_RESUME_CMD; -#if 1 - time = get_timer(0); - while ((*block_addr_p & SCS_SR7) != SCS_SR7) { - if (get_timer(time) > CONFIG_SYS_FLASH_WRITE_TOUT) { - PRINTF("%s:%d: Write timeout @ 0x%p (waited %d mS)\n", - __FUNCTION__, __LINE__, block_addr_p, CONFIG_SYS_FLASH_WRITE_TOUT); - return 1; - } - } - -#endif - return 0; -} -#endif - - -/*----------------------------------------------------------------------- - * Copy memory to flash, returns: - * 0 - OK - * 1 - write timeout - * 2 - Flash not erased - * 4 - Flash not identified - */ -int -write_buff(flash_info_t *info_p, uchar *src_p, ulong addr, ulong count) -{ - int rc = 0; -#ifdef CONFIG_SYS_GEN860T_FLASH_USE_WRITE_BUFFER -#define FLASH_WRITE_BUF_SIZE 0x00000020 /* 32 bytes */ - int i; - uint bufs; - ulong buf_count; - vu_char *sp; - vu_char *dp; -#else - ulong wp; -#endif - - PRINTF("\n%s:%d: src: 0x%.8lx dest: 0x%.8lx size: %d (0x%.8lx)\n", - __FUNCTION__, __LINE__, (ulong)src_p, addr, (uint)count, count); - - if (info_p->flash_id == FLASH_UNKNOWN) { - return 4; - } - -#ifdef CONFIG_SYS_GEN860T_FLASH_USE_WRITE_BUFFER - sp = src_p; - dp = (uchar *)addr; - - /* - * For maximum performance, we want to align the start address to - * the beginning of a write buffer boundary (i.e. A4-A0 of the - * start address = 0). See how many bytes are required to get to a - * write-buffer-aligned address. If that number is non-zero, do - * non buffered writes of the non-aligned data. By doing non-buffered - * writes, we avoid the problem of crossing a block (sector) boundary - * with buffered writes. - */ - buf_count = FLASH_WRITE_BUF_SIZE - (addr & (FLASH_WRITE_BUF_SIZE - 1)); - if (buf_count == FLASH_WRITE_BUF_SIZE) { /* already on a boundary */ - buf_count = 0; - } - if (buf_count > count) { /* not a full buffers worth of data to write */ - buf_count = count; - } - count -= buf_count; - - PRINTF("%s:%d: Write buffer alignment count = %ld\n", - __FUNCTION__, __LINE__, buf_count); - while (buf_count-- >= 1) { - if ((rc = write_data8(info_p, (ulong)dp++, *sp++)) != 0) { - return (rc); - } - } - - PRINTF("%s:%d: count = %ld\n", __FUNCTION__, __LINE__, count); - if (count == 0) { /* all done */ - PRINTF("%s:%d: Less than 1 buffer (%d) worth of bytes\n", - __FUNCTION__, __LINE__, FLASH_WRITE_BUF_SIZE); - return (rc); - } - - /* - * Now that we are write buffer aligned, write full or partial buffers. - * The fact that we are write buffer aligned automatically avoids - * crossing a block address during a write buffer operation. - */ - bufs = count / FLASH_WRITE_BUF_SIZE; - PRINTF("%s:%d: %d (0x%x) buffers to write\n", __FUNCTION__, __LINE__, - bufs, bufs); - while (bufs >= 1) { - rc = write_flash_buffer8(info_p, sp, dp, FLASH_WRITE_BUF_SIZE); - if (rc != 0) { - PRINTF("%s:%d: ** Error writing buf %d\n", - __FUNCTION__, __LINE__, bufs); - return (rc); - } - bufs--; - sp += FLASH_WRITE_BUF_SIZE; - dp += FLASH_WRITE_BUF_SIZE; - } - - /* - * Do the leftovers - */ - i = count % FLASH_WRITE_BUF_SIZE; - PRINTF("%s:%d: %d (0x%x) leftover bytes\n", __FUNCTION__, __LINE__, i, i); - if (i > 0) { - rc = write_flash_buffer8(info_p, sp, dp, i); - } - - sp = (vu_char*)info_p->start[0]; - *sp = SCS_READ_CMD; - return (rc); - -#else - wp = addr; - while (count-- >= 1) { - if((rc = write_data8(info_p, wp++, *src_p++)) != 0) - return (rc); - } - return 0; -#endif -} - - -/*----------------------------------------------------------------------- - * Write a byte to Flash, returns: - * 0 - OK - * 1 - write timeout - * 2 - Flash not erased - */ -static int -write_data8 (flash_info_t *info, ulong dest, uchar data) -{ - vu_char *addr = (vu_char *)dest; - vu_char status; - ulong start; - int flag; - - /* Check if Flash is (sufficiently) erased */ - if ((*addr & data) != data) { - return (2); - } - /* Disable interrupts which might cause a timeout here */ - flag = disable_interrupts(); - - *addr = SCS_PROGRAM_CMD; - *addr = data; - - /* re-enable interrupts if necessary */ - if (flag) - enable_interrupts(); - - start = get_timer (0); - - while (((status = *addr) & SCS_SR7) != SCS_SR7) { - if (get_timer(start) > CONFIG_SYS_FLASH_WRITE_TOUT) { - *addr = SCS_READ_CMD; - return (1); - } - } - *addr = SCS_READ_CMD; - return (0); -} - -/* vim: set ts=4 sw=4 tw=78: */ diff --git a/board/gen860t/fpga.c b/board/gen860t/fpga.c deleted file mode 100644 index dd0ef70..0000000 --- a/board/gen860t/fpga.c +++ /dev/null @@ -1,362 +0,0 @@ -/* - * (C) Copyright 2002 - * Rich Ireland, Enterasys Networks, rireland@enterasys.com. - * Keith Outwater, keith_outwater@mvis.com. - * - * SPDX-License-Identifier: GPL-2.0+ - */ - -/* - * Virtex2 FPGA configuration support for the GEN860T computer - */ - -#include -#include -#include -#include "fpga.h" - -DECLARE_GLOBAL_DATA_PTR; - -#if defined(CONFIG_FPGA) - -#if 0 -#define GEN860T_FPGA_DEBUG -#endif - -#ifdef GEN860T_FPGA_DEBUG -#define PRINTF(fmt,args...) printf (fmt ,##args) -#else -#define PRINTF(fmt,args...) -#endif - -/* - * Port bit numbers for the Selectmap controls - */ -#define FPGA_INIT_BIT_NUM 22 /* PB22 */ -#define FPGA_RESET_BIT_NUM 11 /* PC11 */ -#define FPGA_DONE_BIT_NUM 16 /* PB16 */ -#define FPGA_PROGRAM_BIT_NUM 7 /* PA7 */ - -/* Note that these are pointers to code that is in Flash. They will be - * relocated at runtime. - */ -xilinx_virtex2_slave_selectmap_fns fpga_fns = { - fpga_pre_config_fn, - fpga_pgm_fn, - fpga_init_fn, - fpga_err_fn, - fpga_done_fn, - fpga_clk_fn, - fpga_cs_fn, - fpga_wr_fn, - fpga_read_data_fn, - fpga_write_data_fn, - fpga_busy_fn, - fpga_abort_fn, - fpga_post_config_fn -}; - -xilinx_desc fpga[CONFIG_FPGA_COUNT] = { - {xilinx_virtex2, - slave_selectmap, - XILINX_XC2V3000_SIZE, - (void *) &fpga_fns, - 0} -}; - -/* - * Display FPGA revision information - */ -void print_fpga_revision (void) -{ - vu_long *rev_p = (vu_long *) 0x60000008; - - printf ("FPGA Revision 0x%.8lx" - " (Date %.2lx/%.2lx/%.2lx, Status \"%.1lx\", Version %.3lu)\n", - *rev_p, - ((*rev_p >> 28) & 0xf), - ((*rev_p >> 20) & 0xff), - ((*rev_p >> 12) & 0xff), - ((*rev_p >> 8) & 0xf), (*rev_p & 0xff)); -} - - -/* - * Perform a simple test of the FPGA to processor interface using the FPGA's - * inverting bus test register. The great thing about doing a read/write - * test on a register that inverts it's contents is that you avoid any - * problems with bus charging. - * Return 0 on failure, 1 on success. - */ -int test_fpga_ibtr (void) -{ - vu_long *ibtr_p = (vu_long *) 0x60000010; - vu_long readback; - vu_long compare; - int i; - int j; - int k; - int pass = 1; - - static const ulong bitpattern[] = { - 0xdeadbeef, /* magic ID pattern for debug */ - 0x00000001, /* single bit */ - 0x00000003, /* two adjacent bits */ - 0x00000007, /* three adjacent bits */ - 0x0000000F, /* four adjacent bits */ - 0x00000005, /* two non-adjacent bits */ - 0x00000015, /* three non-adjacent bits */ - 0x00000055, /* four non-adjacent bits */ - 0xaaaaaaaa, /* alternating 1/0 */ - }; - - for (i = 0; i < 1024; i++) { - for (j = 0; j < 31; j++) { - for (k = 0; - k < sizeof (bitpattern) / sizeof (bitpattern[0]); - k++) { - *ibtr_p = compare = (bitpattern[k] << j); - readback = *ibtr_p; - if (readback != ~compare) { - printf ("%s:%d: FPGA test fail: expected 0x%.8lx" " actual 0x%.8lx\n", __FUNCTION__, __LINE__, ~compare, readback); - pass = 0; - break; - } - } - if (!pass) - break; - } - if (!pass) - break; - } - if (pass) { - printf ("FPGA inverting bus test passed\n"); - print_fpga_revision (); - } else { - printf ("** FPGA inverting bus test failed\n"); - } - return pass; -} - - -/* - * Set the active-low FPGA reset signal. - */ -void fpga_reset (int assert) -{ - volatile immap_t *immap = (immap_t *) CONFIG_SYS_IMMR; - - PRINTF ("%s:%d: RESET ", __FUNCTION__, __LINE__); - if (assert) { - immap->im_ioport.iop_pcdat &= ~(0x8000 >> FPGA_RESET_BIT_NUM); - PRINTF ("asserted\n"); - } else { - immap->im_ioport.iop_pcdat |= (0x8000 >> FPGA_RESET_BIT_NUM); - PRINTF ("deasserted\n"); - } -} - - -/* - * Initialize the SelectMap interface. We assume that the mode and the - * initial state of all of the port pins have already been set! - */ -void fpga_selectmap_init (void) -{ - PRINTF ("%s:%d: Initialize SelectMap interface\n", __FUNCTION__, - __LINE__); - fpga_pgm_fn(false, false, 0); /* make sure program pin is inactive */ -} - - -/* - * Initialize the fpga. Return 1 on success, 0 on failure. - */ -int gen860t_init_fpga (void) -{ - int i; - - PRINTF ("%s:%d: Initialize FPGA interface\n", - __FUNCTION__, __LINE__); - fpga_init (); - fpga_selectmap_init (); - - for (i = 0; i < CONFIG_FPGA_COUNT; i++) { - PRINTF ("%s:%d: Adding fpga %d\n", __FUNCTION__, __LINE__, i); - fpga_add (fpga_xilinx, &fpga[i]); - } - return 1; -} - - -/* - * Set the FPGA's active-low SelectMap program line to the specified level - */ -int fpga_pgm_fn (int assert, int flush, int cookie) -{ - volatile immap_t *immap = (immap_t *) CONFIG_SYS_IMMR; - - PRINTF ("%s:%d: FPGA PROGRAM ", __FUNCTION__, __LINE__); - - if (assert) { - immap->im_ioport.iop_padat &= - ~(0x8000 >> FPGA_PROGRAM_BIT_NUM); - PRINTF ("asserted\n"); - } else { - immap->im_ioport.iop_padat |= - (0x8000 >> FPGA_PROGRAM_BIT_NUM); - PRINTF ("deasserted\n"); - } - return assert; -} - - -/* - * Test the state of the active-low FPGA INIT line. Return 1 on INIT - * asserted (low). - */ -int fpga_init_fn (int cookie) -{ - volatile immap_t *immap = (immap_t *) CONFIG_SYS_IMMR; - - PRINTF ("%s:%d: INIT check... ", __FUNCTION__, __LINE__); - if (immap->im_cpm.cp_pbdat & (0x80000000 >> FPGA_INIT_BIT_NUM)) { - PRINTF ("high\n"); - return 0; - } else { - PRINTF ("low\n"); - return 1; - } -} - - -/* - * Test the state of the active-high FPGA DONE pin - */ -int fpga_done_fn (int cookie) -{ - volatile immap_t *immap = (immap_t *) CONFIG_SYS_IMMR; - - PRINTF ("%s:%d: DONE check... ", __FUNCTION__, __LINE__); - if (immap->im_cpm.cp_pbdat & (0x80000000 >> FPGA_DONE_BIT_NUM)) { - PRINTF ("high\n"); - return FPGA_SUCCESS; - } else { - PRINTF ("low\n"); - return FPGA_FAIL; - } -} - - -/* - * Read FPGA SelectMap data. - */ -int fpga_read_data_fn (unsigned char *data, int cookie) -{ - vu_char *p = (vu_char *) SELECTMAP_BASE; - - *data = *p; -#if 0 - PRINTF ("%s: Read 0x%x into 0x%p\n", __FUNCTION__, (int) data, data); -#endif - return (int) data; -} - - -/* - * Write data to the FPGA SelectMap port - */ -int fpga_write_data_fn (unsigned char data, int flush, int cookie) -{ - vu_char *p = (vu_char *) SELECTMAP_BASE; - -#if 0 - PRINTF ("%s: Write Data 0x%x\n", __FUNCTION__, (int) data); -#endif - *p = data; - return (int) data; -} - - -/* - * Abort and FPGA operation - */ -int fpga_abort_fn (int cookie) -{ - PRINTF ("%s:%d: FPGA program sequence aborted\n", - __FUNCTION__, __LINE__); - return FPGA_FAIL; -} - - -/* - * FPGA pre-configuration function. Just make sure that - * FPGA reset is asserted to keep the FPGA from starting up after - * configuration. - */ -int fpga_pre_config_fn (int cookie) -{ - PRINTF ("%s:%d: FPGA pre-configuration\n", __FUNCTION__, __LINE__); - fpga_reset(true); - return 0; -} - - -/* - * FPGA post configuration function. Blip the FPGA reset line and then see if - * the FPGA appears to be running. - */ -int fpga_post_config_fn (int cookie) -{ - int rc; - - PRINTF ("%s:%d: FPGA post configuration\n", __FUNCTION__, __LINE__); - fpga_reset(true); - udelay (1000); - fpga_reset(false); - udelay (1000); - - /* - * Use the FPGA,s inverting bus test register to do a simple test of the - * processor interface. - */ - rc = test_fpga_ibtr (); - return rc; -} - - -/* - * Clock, chip select and write signal assert functions and error check - * and busy functions. These are only stubs because the GEN860T selectmap - * interface handles sequencing of control signals automatically (it uses - * a memory-mapped interface to the FPGA SelectMap port). The design of - * the interface guarantees that the SelectMap port cannot be overrun so - * no busy check is needed. A configuration error is signalled by INIT - * going low during configuration, so there is no need for a separate error - * function. - */ -int fpga_clk_fn (int assert_clk, int flush, int cookie) -{ - return assert_clk; -} - -int fpga_cs_fn (int assert_cs, int flush, int cookie) -{ - return assert_cs; -} - -int fpga_wr_fn (int assert_write, int flush, int cookie) -{ - return assert_write; -} - -int fpga_err_fn (int cookie) -{ - return 0; -} - -int fpga_busy_fn (int cookie) -{ - return 0; -} -#endif diff --git a/board/gen860t/fpga.h b/board/gen860t/fpga.h deleted file mode 100644 index 95c15c4..0000000 --- a/board/gen860t/fpga.h +++ /dev/null @@ -1,26 +0,0 @@ -/* - * (C) Copyright 2002 - * Rich Ireland, Enterasys Networks, rireland@enterasys.com. - * Keith Outwater, keith_outwater@mvis.com. - * - * SPDX-License-Identifier: GPL-2.0+ - */ - -/* - * Virtex2 FPGA configuration support for the GEN860T computer - */ - -extern int gen860t_init_fpga(void); -extern int fpga_pgm_fn(int assert_pgm, int flush, int cookie); -extern int fpga_init_fn(int cookie); -extern int fpga_err_fn(int cookie); -extern int fpga_done_fn(int cookie); -extern int fpga_clk_fn(int assert_clk, int flush, int cookie); -extern int fpga_cs_fn(int assert_cs, int flush, int cookie); -extern int fpga_wr_fn(int assert_write, int flush, int cookie); -extern int fpga_read_data_fn(unsigned char *data, int cookie); -extern int fpga_write_data_fn(unsigned char data, int flush, int cookie); -extern int fpga_busy_fn(int cookie); -extern int fpga_abort_fn(int cookie ); -extern int fpga_pre_config_fn(int cookie ); -extern int fpga_post_config_fn(int cookie ); diff --git a/board/gen860t/gen860t.c b/board/gen860t/gen860t.c deleted file mode 100644 index fe139f4..0000000 --- a/board/gen860t/gen860t.c +++ /dev/null @@ -1,278 +0,0 @@ -/* - * (C) Copyright 2000 - * Wolfgang Denk, DENX Software Engineering, wd@denx.de. - * Keith Outwater, keith_outwater@mvis.com - * - * SPDX-License-Identifier: GPL-2.0+ - */ - -#include -#include -#include -#include -#include "beeper.h" -#include "fpga.h" -#include "ioport.h" - -DECLARE_GLOBAL_DATA_PTR; - -#ifdef CONFIG_STATUS_LED -#include -#endif - -#if defined(CONFIG_CMD_MII) && defined(CONFIG_MII) -#include -#endif - -#if 0 -#define GEN860T_DEBUG -#endif - -#ifdef GEN860T_DEBUG -#define PRINTF(fmt,args...) printf (fmt ,##args) -#else -#define PRINTF(fmt,args...) -#endif - -/* - * The following UPM init tables were generated automatically by - * Motorola's MCUINIT program. See the README file for UPM to - * SDRAM pin assignments if you want to type this data into - * MCUINIT in order to reverse engineer the waveforms. - */ - -/* - * UPM initialization tables for MICRON MT48LC16M16A2TG SDRAM devices - * (UPMA) and Virtex FPGA SelectMap interface (UPMB). - * NOTE that unused areas of the table are used to hold NOP, precharge - * and mode register set sequences. - * - */ -#define UPMA_NOP_ADDR 0x5 -#define UPMA_PRECHARGE_ADDR 0x6 -#define UPMA_MRS_ADDR 0x12 - -#define UPM_SINGLE_READ_ADDR 0x00 -#define UPM_BURST_READ_ADDR 0x08 -#define UPM_SINGLE_WRITE_ADDR 0x18 -#define UPM_BURST_WRITE_ADDR 0x20 -#define UPM_REFRESH_ADDR 0x30 - -const uint sdram_upm_table[] = { - /* single read (offset 0x00 in upm ram) */ - 0x0e0fdc04, 0x01adfc04, 0x0fbffc00, 0x1fff5c05, - 0xffffffff, 0x0fffffcd, 0x0fff0fce, 0xefcfffff, - /* burst read (offset 0x08 in upm ram) */ - 0x0f0fdc04, 0x00fdfc04, 0xf0fffc00, 0xf0fffc00, - 0xf1fffc00, 0xfffffc00, 0xfffffc05, 0xffffffff, - 0xffffffff, 0xffffffff, 0x0ffffff4, 0x1f3d5ff4, - 0xfffffff4, 0xfffffff5, 0xffffffff, 0xffffffff, - /* single write (offset 0x18 in upm ram) */ - 0x0f0fdc04, 0x00ad3c00, 0x1fff5c05, 0xffffffff, - 0xffffffff, 0xffffffff, 0xffffffff, 0xffffffff, - /* burst write (offset 0x20 in upm ram) */ - 0x0f0fdc00, 0x10fd7c00, 0xf0fffc00, 0xf0fffc00, - 0xf1fffc04, 0xfffffc05, 0xffffffff, 0xffffffff, - 0xffffffff, 0xffffffff, 0xffffffff, 0xfffff7ff, - 0xffffffff, 0xffffffff, 0xffffffff, 0xffffffff, - /* refresh (offset 0x30 in upm ram) */ - 0x1ffddc84, 0xfffffc04, 0xfffffc04, 0xfffffc84, - 0xfffffc05, 0xffffffff, 0xffffffff, 0xffffffff, - 0xffffffff, 0xffffffff, 0xffffffff, 0xffffffff, - /* exception (offset 0x3C in upm ram) */ -}; - -const uint selectmap_upm_table[] = { - /* single read (offset 0x00 in upm ram) */ - 0x88fffc06, 0x00fff404, 0x00fffc04, 0x33fffc00, - 0xfffffc05, 0xffffffff, 0xffffffff, 0xffffffff, - /* burst read (offset 0x08 in upm ram) */ - 0xfffffc04, 0xfffffc05, 0xffffffff, 0xffffffff, - 0xffffffff, 0xffffffff, 0xffffffff, 0xffffffff, - 0xffffffff, 0xffffffff, 0xffffffff, 0xffffffff, - 0xffffffff, 0xffffffff, 0xffffffff, 0xffffffff, - /* single write (offset 0x18 in upm ram) */ - 0x88fffc04, 0x00fff400, 0x77fffc05, 0xffffffff, - 0xffffffff, 0xffffffff, 0xffffffff, 0xffffffff, - /* burst write (offset 0x20 in upm ram) */ - 0xfffffc04, 0xfffffc05, 0xffffffff, 0xffffffff, - 0xffffffff, 0xffffffff, 0xffffffff, 0xffffffff, - 0xffffffff, 0xffffffff, 0xffffffff, 0xffffffff, - 0xffffffff, 0xffffffff, 0xffffffff, 0xffffffff, - /* refresh (offset 0x30 in upm ram) */ - 0xfffffc04, 0xfffffc05, 0xffffffff, 0xffffffff, - 0xffffffff, 0xffffffff, 0xffffffff, 0xffffffff, - 0xffffffff, 0xffffffff, 0xffffffff, 0xffffffff, - /* exception (offset 0x3C in upm ram) */ - 0xfffffc05, 0xffffffff, 0xffffffff, 0xffffffff -}; - -/* - * Check board identity. Always successful (gives information only) - */ -int checkboard (void) -{ - char *s; - char buf[64]; - int i; - - i = getenv_f("board_id", buf, sizeof (buf)); - s = (i > 0) ? buf : NULL; - - if (s) { - printf ("%s ", s); - } else { - printf (" "); - } - - i = getenv_f("serial#", buf, sizeof (buf)); - s = (i > 0) ? buf : NULL; - - if (s) { - printf ("S/N %s\n", s); - } else { - printf ("S/N \n"); - } - - printf ("CPU at %s MHz, ", strmhz (buf, gd->cpu_clk)); - printf ("local bus at %s MHz\n", strmhz (buf, gd->bus_clk)); - return (0); -} - -/* - * Initialize SDRAM - */ -phys_size_t initdram (int board_type) -{ - volatile immap_t *immr = (immap_t *) CONFIG_SYS_IMMR; - volatile memctl8xx_t *memctl = &immr->im_memctl; - - upmconfig (UPMA, - (uint *) sdram_upm_table, - sizeof (sdram_upm_table) / sizeof (uint) - ); - - /* - * Setup MAMR register - */ - memctl->memc_mptpr = CONFIG_SYS_MPTPR_1BK_8K; - memctl->memc_mamr = CONFIG_SYS_MAMR_8COL & (~(MAMR_PTAE)); /* no refresh yet */ - - /* - * Map CS1* to SDRAM bank - */ - memctl->memc_or1 = CONFIG_SYS_OR1; - memctl->memc_br1 = CONFIG_SYS_BR1; - - /* - * Perform SDRAM initialization sequence: - * 1. Apply at least one NOP command - * 2. 100 uS delay (JEDEC standard says 200 uS) - * 3. Issue 4 precharge commands - * 4. Perform two refresh cycles - * 5. Program mode register - * - * Program SDRAM for standard operation, sequential burst, burst length - * of 4, CAS latency of 2. - */ - memctl->memc_mar = 0x00000000; - memctl->memc_mcr = MCR_UPM_A | MCR_OP_RUN | MCR_MB_CS1 | - MCR_MLCF (0) | UPMA_NOP_ADDR; - udelay (200); - memctl->memc_mar = 0x00000000; - memctl->memc_mcr = MCR_UPM_A | MCR_OP_RUN | MCR_MB_CS1 | - MCR_MLCF (4) | UPMA_PRECHARGE_ADDR; - - memctl->memc_mar = 0x00000000; - memctl->memc_mcr = MCR_UPM_A | MCR_OP_RUN | MCR_MB_CS1 | - MCR_MLCF (2) | UPM_REFRESH_ADDR; - - memctl->memc_mar = 0x00000088; - memctl->memc_mcr = MCR_UPM_A | MCR_OP_RUN | MCR_MB_CS1 | - MCR_MLCF (1) | UPMA_MRS_ADDR; - - memctl->memc_mar = 0x00000000; - memctl->memc_mcr = MCR_UPM_A | MCR_OP_RUN | MCR_MB_CS1 | - MCR_MLCF (0) | UPMA_NOP_ADDR; - /* - * Enable refresh - */ - memctl->memc_mamr |= MAMR_PTAE; - - return (SDRAM_SIZE); -} - -/* - * Disk On Chip (DOC) Millenium initialization. - * The DOC lives in the CS2* space - */ -#if defined(CONFIG_CMD_DOC) -void doc_init (void) -{ - printf ("Probing at 0x%.8x: ", DOC_BASE); - doc_probe (DOC_BASE); -} -#endif - -/* - * Miscellaneous intialization - */ -int misc_init_r (void) -{ - volatile immap_t *immr = (immap_t *) CONFIG_SYS_IMMR; - volatile memctl8xx_t *memctl = &immr->im_memctl; - - /* - * Set up UPMB to handle the Virtex FPGA SelectMap interface - */ - upmconfig (UPMB, (uint *) selectmap_upm_table, - sizeof (selectmap_upm_table) / sizeof (uint)); - - memctl->memc_mbmr = 0x0; - - config_mpc8xx_ioports (immr); - -#if defined(CONFIG_CMD_MII) - mii_init (); -#endif - -#if defined(CONFIG_FPGA) - gen860t_init_fpga (); -#endif - return 0; -} - -/* - * Final init hook before entering command loop. - */ -int last_stage_init (void) -{ -#if !defined(CONFIG_SC) - char buf[256]; - int i; - - /* - * Turn the beeper volume all the way down in case this is a warm boot. - */ - set_beeper_volume (-64); - init_beeper (); - - /* - * Read the environment to see what to do with the beeper - */ - i = getenv_f("beeper", buf, sizeof (buf)); - if (i > 0) { - do_beeper (buf); - } -#endif - return 0; -} - -/* - * Stub to make POST code happy. Can't self-poweroff, so just hang. - */ -void board_poweroff (void) -{ - puts ("### Please power off the board ###\n"); - while (1); -} diff --git a/board/gen860t/ioport.c b/board/gen860t/ioport.c deleted file mode 100644 index 7cd209b..0000000 --- a/board/gen860t/ioport.c +++ /dev/null @@ -1,331 +0,0 @@ -/* - * (C) Copyright 2000 - * Wolfgang Denk, DENX Software Engineering, wd@denx.de. - * - * SPDX-License-Identifier: GPL-2.0+ - */ - -#include -#include -#include -#include "ioport.h" - -#if 0 -#define IOPORT_DEBUG -#endif - -#ifdef IOPORT_DEBUG -#define PRINTF(fmt,args...) printf (fmt ,##args) -#else -#define PRINTF(fmt,args...) -#endif - -/* - * The ioport configuration table. - */ -const mpc8xx_iop_conf_t iop_conf_tab[NUM_PORTS][PORT_BITS] = { - /* - * Port A configuration - * Pin Signal Type Active Initial state - * PA7 fpgaProgramLowOut Out Low High - * PA1 fpgaCoreVoltageFailLow In Low N/A - */ - { /* conf ppar psor pdir podr pdat pint function */ - /* N/A */ { 0, 0, 0, 0, 0, 0, 0 }, /* No pin */ - /* N/A */ { 0, 0, 0, 0, 0, 0, 0 }, /* No pin */ - /* PA15 */ { 0, 0, 0, 0, 0, 0, 0 }, /* */ - /* PA14 */ { 0, 0, 0, 0, 0, 0, 0 }, /* */ - /* PA13 */ { 0, 0, 0, 0, 0, 0, 0 }, /* */ - /* PA12 */ { 0, 0, 0, 0, 0, 0, 0 }, /* */ - /* PA11 */ { 0, 0, 0, 0, 0, 0, 0 }, /* */ - /* PA10 */ { 0, 0, 0, 0, 0, 0, 0 }, /* */ - /* PA9 */ { 1, 0, 0, 1, 0, 0, 0 }, /* grn bicolor LED 1*/ - /* PA8 */ { 1, 0, 0, 1, 0, 0, 0 }, /* red bicolor LED 1*/ - /* PA7 */ { 1, 0, 0, 1, 0, 1, 0 }, /* fpgaProgramLow */ - /* PA6 */ { 0, 0, 0, 0, 0, 0, 0 }, /* */ - /* PA5 */ { 1, 0, 0, 1, 0, 0, 0 }, /* grn bicolor LED 0*/ - /* PA4 */ { 1, 0, 0, 1, 0, 0, 0 }, /* red bicolor LED 0*/ - /* PA3 */ { 0, 0, 0, 0, 0, 0, 0 }, /* */ - /* PA2 */ { 0, 0, 0, 0, 0, 0, 0 }, /* */ -#if !defined(CONFIG_SC) - /* PA1 */ { 1, 0, 0, 0, 0, 0, 0 }, /* fpgaCoreVoltageFail*/ -#else - /* PA1 */ { 0, 0, 0, 0, 0, 0, 0 }, /* */ -#endif - /* PA0 */ { 0, 0, 0, 0, 0, 0, 0 } /* */ - }, - - /* - * Port B configuration - * Pin Signal Type Active Initial state - * PB14 docBusyLowIn In Low X - * PB15 gpio1Sig Out High Low - * PB16 fpgaDoneBi In High X - * PB17 swBitOkLowOut Out Low High - * PB19 speakerVolSig Out/Hi-Z High/Low High (Hi-Z) - * PB22 fpgaInitLowBi In Low X - * PB23 batteryOkSig In High X - * PB31 pulseCatcherClr Out High 0 - */ - { /* conf ppar psor pdir podr pdat pint function */ -#if !defined(CONFIG_SC) - /* PB31 */ { 0, 0, 0, 0, 0, 0, 0 }, /* */ -#else - /* PB31 */ { 1, 0, 0, 1, 0, 0, 0 }, /* pulseCatcherClr */ -#endif - /* PB30 */ { 0, 0, 0, 0, 0, 0, 0 }, /* */ - /* PB29 */ { 0, 0, 0, 0, 0, 0, 0 }, /* */ - /* PB28 */ { 0, 0, 0, 0, 0, 0, 0 }, /* */ - /* PB27 */ { 0, 0, 0, 0, 0, 0, 0 }, /* */ - /* PB26 */ { 0, 0, 0, 0, 0, 0, 0 }, /* */ - /* PB25 */ { 0, 0, 0, 0, 0, 0, 0 }, /* */ - /* PB24 */ { 0, 0, 0, 0, 0, 0, 0 }, /* */ -#if !defined(CONFIG_SC) - /* PB23 */ { 1, 0, 0, 0, 0, 0, 0 }, /* batteryOk */ -#else - /* PB23 */ { 0, 0, 0, 0, 0, 0, 0 }, /* */ -#endif - /* PB22 */ { 1, 0, 0, 0, 0, 0, 0 }, /* fpgaInitLowBi */ - /* PB21 */ { 0, 0, 0, 0, 0, 0, 0 }, /* */ - /* PB20 */ { 0, 0, 0, 0, 0, 0, 0 }, /* */ -#if !defined(CONFIG_SC) - /* PB19 */ { 1, 0, 0, 1, 1, 1, 0 }, /* speakerVol */ -#else - /* PB19 */ { 0, 0, 0, 1, 1, 1, 0 }, /* */ -#endif - /* PB18 */ { 0, 0, 0, 0, 0, 0, 0 }, /* */ - /* PB17 */ { 1, 0, 0, 1, 0, 1, 0 }, /* swBitOkLow */ - /* PB16 */ { 1, 0, 0, 0, 0, 0, 0 }, /* fpgaDone */ - /* PB15 */ { 1, 0, 0, 1, 0, 0, 0 }, /* gpio1 */ -#if !defined(CONFIG_SC) - /* PB14 */ { 1, 0, 0, 0, 0, 0, 0 } /* docBusyLow */ -#else - /* PB14 */ { 0, 0, 0, 0, 0, 0, 0 } /* */ -#endif - }, - - /* - * Port C configuration - * Pin Signal Type Active Initial state - * PC4 i2cBus1EnSig Out High High - * PC5 i2cBus2EnSig Out High High - * PC6 gpio0Sig Out High Low - * PC8 i2cBus3EnSig Out High High - * PC10 i2cBus4EnSig Out High High - * PC11 fpgaResetLowOut Out Low High - * PC12 systemBitOkIn In High X - * PC15 selfDreqLow In Low X - */ - { /* conf ppar psor pdir podr pdat pint function */ - /* N/A */ { 0, 0, 0, 0, 0, 0, 0 }, /* */ - /* N/A */ { 0, 0, 0, 0, 0, 0, 0 }, /* */ - /* PC15 */ { 1, 0, 0, 0, 0, 0, 0 }, /* selfDreqLowIn */ - /* PC14 */ { 0, 0, 0, 0, 0, 0, 0 }, /* */ - /* PC13 */ { 0, 0, 0, 0, 0, 0, 0 }, /* */ -#if !defined(CONFIG_SC) - /* PC12 */ { 1, 0, 0, 0, 0, 0, 0 }, /* systemBitOkIn */ -#else - /* PC12 */ { 0, 0, 0, 0, 0, 0, 0 }, /* */ -#endif - /* PC11 */ { 1, 0, 0, 1, 0, 1, 0 }, /* fpgaResetLowOut */ -#if !defined(CONFIG_SC) - /* PC10 */ { 1, 0, 0, 1, 0, 1, 0 }, /* i2cBus4EnSig */ -#else - /* PC10 */ { 0, 0, 0, 1, 0, 1, 0 }, /* */ -#endif - /* PC9 */ { 0, 0, 0, 0, 0, 0, 0 }, /* */ -#if !defined(CONFIG_SC) - /* PC8 */ { 1, 0, 0, 1, 0, 1, 0 }, /* i2cBus3EnSig */ -#else - /* PC8 */ { 0, 0, 0, 1, 0, 1, 0 }, /* */ -#endif - /* PC7 */ { 0, 0, 0, 0, 0, 0, 0 }, /* */ - /* PC6 */ { 1, 0, 0, 1, 0, 1, 0 }, /* gpio0 */ -#if !defined(CONFIG_SC) - /* PC5 */ { 1, 0, 0, 1, 0, 1, 0 }, /* i2cBus2EnSig */ - /* PC4 */ { 1, 0, 0, 1, 0, 1, 0 }, /* i2cBus1EnSig */ -#else - /* PC5 */ { 0, 0, 0, 1, 0, 1, 0 }, /* */ - /* PC4 */ { 0, 0, 0, 1, 0, 1, 0 }, /* */ -#endif - /* N/A */ { 0, 0, 0, 0, 0, 0, 0 }, /* */ - /* N/A */ { 0, 0, 0, 0, 0, 0, 0 }, /* */ - /* N/A */ { 0, 0, 0, 0, 0, 0, 0 }, /* */ - /* N/A */ { 0, 0, 0, 0, 0, 0, 0 } /* */ - }, - - /* - * Port D configuration - */ - { /* conf ppar psor pdir podr pdat pint function */ - /* N/A */ { 0, 0, 0, 0, 0, 0, 0 }, /* */ - /* N/A */ { 0, 0, 0, 0, 0, 0, 0 }, /* */ - /* PD15 */ { 0, 0, 0, 0, 0, 0, 0 }, /* */ - /* PD14 */ { 0, 0, 0, 0, 0, 0, 0 }, /* */ - /* PD13 */ { 0, 0, 0, 0, 0, 0, 0 }, /* */ - /* PD12 */ { 0, 0, 0, 0, 0, 0, 0 }, /* */ - /* PD11 */ { 0, 0, 0, 0, 0, 0, 0 }, /* */ - /* PD10 */ { 0, 0, 0, 0, 0, 0, 0 }, /* */ - /* PD9 */ { 0, 0, 0, 0, 0, 0, 0 }, /* */ - /* PD8 */ { 0, 0, 0, 0, 0, 0, 0 }, /* */ - /* PD7 */ { 0, 0, 0, 0, 0, 0, 0 }, /* */ - /* PD6 */ { 0, 0, 0, 0, 0, 0, 0 }, /* */ - /* PD5 */ { 0, 0, 0, 0, 0, 0, 0 }, /* */ - /* PD4 */ { 0, 0, 0, 0, 0, 0, 0 }, /* */ - /* PD3 */ { 0, 0, 0, 0, 0, 0, 0 }, /* */ - /* N/A */ { 0, 0, 0, 0, 0, 0, 0 }, /* */ - /* N/A */ { 0, 0, 0, 0, 0, 0, 0 }, /* */ - /* N/A */ { 0, 0, 0, 0, 0, 0, 0 } /* */ - } -}; - -/* - * Configure the MPC8XX I/O ports per the ioport configuration table - * (taken from ./arch/powerpc/cpu/mpc8260/cpu_init.c) - */ -void config_mpc8xx_ioports (volatile immap_t * immr) -{ - int portnum; - - for (portnum = 0; portnum < NUM_PORTS; portnum++) { - uint pmsk = 0, ppar = 0, psor = 0, pdir = 0; - uint podr = 0, pdat = 0, pint = 0; - uint msk = 1; - mpc8xx_iop_conf_t *iopc = - (mpc8xx_iop_conf_t *) & iop_conf_tab[portnum][0]; - mpc8xx_iop_conf_t *eiopc = iopc + PORT_BITS; - - /* - * For all ports except port B, ignore the two don't care entries - * in the configuration tables. - */ - if (portnum != 1) { - iopc = (mpc8xx_iop_conf_t *) & - iop_conf_tab[portnum][2]; - } - - /* - * NOTE: index 0 refers to pin 17, index 17 refers to pin 0 - */ - while (iopc < eiopc) { - if (iopc->conf) { - pmsk |= msk; - if (iopc->ppar) - ppar |= msk; - if (iopc->psor) - psor |= msk; - if (iopc->pdir) - pdir |= msk; - if (iopc->podr) - podr |= msk; - if (iopc->pdat) - pdat |= msk; - if (iopc->pint) - pint |= msk; - } - msk <<= 1; - iopc++; - } - - PRINTF ("%s:%d:\n portnum=%d ", __FUNCTION__, __LINE__, - portnum); -#ifdef IOPORT_DEBUG - switch (portnum) { - case 0: - printf ("(A)\n"); - break; - case 1: - printf ("(B)\n"); - break; - case 2: - printf ("(C)\n"); - break; - case 3: - printf ("(D)\n"); - break; - default: - printf ("(?)\n"); - break; - } -#endif - PRINTF (" ppar=0x%.8x pdir=0x%.8x podr=0x%.8x\n" - " pdat=0x%.8x psor=0x%.8x pint=0x%.8x pmsk=0x%.8x\n", - ppar, pdir, podr, pdat, psor, pint, pmsk); - - /* - * Have to handle the ioports on a port-by-port basis since there - * are three different flavors. - */ - if (pmsk != 0) { - uint tpmsk = ~pmsk; - - if (0 == portnum) { /* port A */ - immr->im_ioport.iop_papar &= tpmsk; - immr->im_ioport.iop_padat = - (immr->im_ioport. - iop_padat & tpmsk) | pdat; - immr->im_ioport.iop_padir = - (immr->im_ioport. - iop_padir & tpmsk) | pdir; - immr->im_ioport.iop_paodr = - (immr->im_ioport. - iop_paodr & tpmsk) | podr; - immr->im_ioport.iop_papar |= ppar; - } else if (1 == portnum) { /* port B */ - immr->im_cpm.cp_pbpar &= tpmsk; - immr->im_cpm.cp_pbdat = - (immr->im_cpm. - cp_pbdat & tpmsk) | pdat; - immr->im_cpm.cp_pbdir = - (immr->im_cpm. - cp_pbdir & tpmsk) | pdir; - immr->im_cpm.cp_pbodr = - (immr->im_cpm. - cp_pbodr & tpmsk) | podr; - immr->im_cpm.cp_pbpar |= ppar; - } else if (2 == portnum) { /* port C */ - immr->im_ioport.iop_pcpar &= tpmsk; - immr->im_ioport.iop_pcdat = - (immr->im_ioport. - iop_pcdat & tpmsk) | pdat; - immr->im_ioport.iop_pcdir = - (immr->im_ioport. - iop_pcdir & tpmsk) | pdir; - immr->im_ioport.iop_pcint = - (immr->im_ioport. - iop_pcint & tpmsk) | pint; - immr->im_ioport.iop_pcso = - (immr->im_ioport. - iop_pcso & tpmsk) | psor; - immr->im_ioport.iop_pcpar |= ppar; - } else if (3 == portnum) { /* port D */ - immr->im_ioport.iop_pdpar &= tpmsk; - immr->im_ioport.iop_pddat = - (immr->im_ioport. - iop_pddat & tpmsk) | pdat; - immr->im_ioport.iop_pddir = - (immr->im_ioport. - iop_pddir & tpmsk) | pdir; - immr->im_ioport.iop_pdpar |= ppar; - } - } - } - - PRINTF ("%s:%d: Port A:\n papar=0x%.4x padir=0x%.4x" - " paodr=0x%.4x\n padat=0x%.4x\n", __FUNCTION__, __LINE__, - immr->im_ioport.iop_papar, immr->im_ioport.iop_padir, - immr->im_ioport.iop_paodr, immr->im_ioport.iop_padat); - PRINTF ("%s:%d: Port B:\n pbpar=0x%.8x pbdir=0x%.8x" - " pbodr=0x%.8x\n pbdat=0x%.8x\n", __FUNCTION__, __LINE__, - immr->im_cpm.cp_pbpar, immr->im_cpm.cp_pbdir, - immr->im_cpm.cp_pbodr, immr->im_cpm.cp_pbdat); - PRINTF ("%s:%d: Port C:\n pcpar=0x%.4x pcdir=0x%.4x" - " pcdat=0x%.4x\n pcso=0x%.4x pcint=0x%.4x\n ", - __FUNCTION__, __LINE__, immr->im_ioport.iop_pcpar, - immr->im_ioport.iop_pcdir, immr->im_ioport.iop_pcdat, - immr->im_ioport.iop_pcso, immr->im_ioport.iop_pcint); - PRINTF ("%s:%d: Port D:\n pdpar=0x%.4x pddir=0x%.4x" - " pddat=0x%.4x\n", __FUNCTION__, __LINE__, - immr->im_ioport.iop_pdpar, immr->im_ioport.iop_pddir, - immr->im_ioport.iop_pddat); -} diff --git a/board/gen860t/ioport.h b/board/gen860t/ioport.h deleted file mode 100644 index 4ac2aa4..0000000 --- a/board/gen860t/ioport.h +++ /dev/null @@ -1,26 +0,0 @@ -/* - * (C) Copyright 2000 - * Wolfgang Denk, DENX Software Engineering, wd@denx.de. - * Keith Outwater, keith_outwater@mvis.com - * - * SPDX-License-Identifier: GPL-2.0+ - */ - -#define NUM_PORTS 4 -#define PORT_BITS 18 - -/* - * This structure provides configuration information for one port pin. - * We include all fields needed to initialize any of the ioports. - */ -typedef struct { - unsigned char conf:1; /* If 1, configure this port */ - unsigned char ppar:1; /* Port Pin Assignment Register */ - unsigned char psor:1; /* Port Special Options Register */ - unsigned char pdir:1; /* Port Data Direction Register */ - unsigned char podr:1; /* Port Open Drain Register */ - unsigned char pdat:1; /* Port Data Register */ - unsigned char pint:1; /* Port Interrupt Register */ -} mpc8xx_iop_conf_t; - -extern void config_mpc8xx_ioports(volatile immap_t *immr); diff --git a/board/gen860t/u-boot-flashenv.lds b/board/gen860t/u-boot-flashenv.lds deleted file mode 100644 index 7a4a763..0000000 --- a/board/gen860t/u-boot-flashenv.lds +++ /dev/null @@ -1,92 +0,0 @@ -/* - * Linker command file for the GEN860T board when the environment is - * stored in flash memory. - * - * (C) Copyright 2000-2010 - * Wolfgang Denk, DENX Software Engineering, wd@denx.de. - * - * SPDX-License-Identifier: GPL-2.0+ - */ - -OUTPUT_ARCH(powerpc) -SECTIONS -{ - /* - * Read-only sections, merged into text segment: - */ - . = + SIZEOF_HEADERS; - .text : - { - arch/powerpc/cpu/mpc8xx/start.o (.text*) - arch/powerpc/cpu/mpc8xx/traps.o (.text*) - - *(.text*) - } - _etext = .; - PROVIDE (etext = .); - .rodata : - { - *(SORT_BY_ALIGNMENT(SORT_BY_NAME(.rodata*))) - } - - /* - * Read-write section, merged into data segment: - */ - . = (. + 0x00FF) & 0xFFFFFF00; - _erotext = .; - PROVIDE (erotext = .); - .reloc : - { - KEEP(*(.got)) - _GOT2_TABLE_ = .; - KEEP(*(.got2)) - _FIXUP_TABLE_ = .; - KEEP(*(.fixup)) - } - __got2_entries = (_FIXUP_TABLE_ - _GOT2_TABLE_) >>2; - __fixup_entries = (. - _FIXUP_TABLE_)>>2; - - .data: - { - *(.data*) - *(.sdata*) - } - _edata = .; - PROVIDE (edata = .); - - . = .; - - .u_boot_list : { - KEEP(*(SORT(.u_boot_list*))); - } - - . = .; - __start___ex_table = .; - __ex_table : { *(__ex_table) } - __stop___ex_table = .; - - . = ALIGN(256); - __init_begin = .; - .text.init : { *(.text.init) } - .data.init : { *(.data.init) } - . = ALIGN(256); - __init_end = .; - - __bss_start = .; - .bss (NOLOAD) : - { - *(.bss*) - *(.sbss*) - *(COMMON) - . = ALIGN(4); - } - - __bss_end = . ; - PROVIDE (end = .); - - .ppcenv: - { - . = env_offset; - common/env_embedded.o - } -} diff --git a/board/gen860t/u-boot.lds b/board/gen860t/u-boot.lds deleted file mode 100644 index 3371c0a..0000000 --- a/board/gen860t/u-boot.lds +++ /dev/null @@ -1,87 +0,0 @@ -/* - * Linker command file for the GEN860T board. - * - * (C) Copyright 2000-2010 - * Wolfgang Denk, DENX Software Engineering, wd@denx.de. - * - * SPDX-License-Identifier: GPL-2.0+ - */ - -OUTPUT_ARCH(powerpc) -SECTIONS -{ - /* - * Read-only sections, merged into text segment: - */ - . = + SIZEOF_HEADERS; - .text : - { - arch/powerpc/cpu/mpc8xx/start.o (.text*) - arch/powerpc/cpu/mpc8xx/traps.o (.text*) - - *(.text*) - } - _etext = .; - PROVIDE (etext = .); - .rodata : - { - *(SORT_BY_ALIGNMENT(SORT_BY_NAME(.rodata*))) - } - - /* - * Read-write section, merged into data segment: - */ - . = (. + 0x00FF) & 0xFFFFFF00; - _erotext = .; - PROVIDE (erotext = .); - .reloc : - { - _GOT2_TABLE_ = .; - KEEP(*(.got2)) - KEEP(*(.got)) - PROVIDE(_GLOBAL_OFFSET_TABLE_ = . + 4); - _FIXUP_TABLE_ = .; - KEEP(*(.fixup)) - } - __got2_entries = ((_GLOBAL_OFFSET_TABLE_ - _GOT2_TABLE_) >> 2) - 1; - __fixup_entries = (. - _FIXUP_TABLE_)>>2; - - .data : - { - *(.data*) - *(.sdata*) - } - _edata = .; - PROVIDE (edata = .); - - . = .; - - . = ALIGN(4); - .u_boot_list : { - KEEP(*(SORT(.u_boot_list*))); - } - - - . = .; - __start___ex_table = .; - __ex_table : { *(__ex_table) } - __stop___ex_table = .; - - . = ALIGN(256); - __init_begin = .; - .text.init : { *(.text.init) } - .data.init : { *(.data.init) } - . = ALIGN(256); - __init_end = .; - - __bss_start = .; - .bss (NOLOAD) : - { - *(.bss*) - *(.sbss*) - *(COMMON) - . = ALIGN(4); - } - __bss_end = . ; - PROVIDE (end = .); -} diff --git a/configs/GEN860T_SC_defconfig b/configs/GEN860T_SC_defconfig deleted file mode 100644 index ff624db..0000000 --- a/configs/GEN860T_SC_defconfig +++ /dev/null @@ -1,4 +0,0 @@ -CONFIG_SYS_EXTRA_OPTIONS="SC" -CONFIG_PPC=y -CONFIG_8xx=y -CONFIG_TARGET_GEN860T=y diff --git a/configs/GEN860T_defconfig b/configs/GEN860T_defconfig deleted file mode 100644 index e672623..0000000 --- a/configs/GEN860T_defconfig +++ /dev/null @@ -1,3 +0,0 @@ -CONFIG_PPC=y -CONFIG_8xx=y -CONFIG_TARGET_GEN860T=y diff --git a/doc/README.scrapyard b/doc/README.scrapyard index b984d76..4ae2a65 100644 --- a/doc/README.scrapyard +++ b/doc/README.scrapyard @@ -12,6 +12,7 @@ The list should be sorted in reverse chronological order. Board Arch CPU Commit Removed Last known maintainer/contact ================================================================================================= +gen860t powerpc mpc8xx - - Keith Outwater sixnet powerpc mpc8xx - - Dave Ellis svm_sc8xx powerpc mpc8xx - - John Zhan stxxtc powerpc mpc8xx - - Dan Malek diff --git a/include/commproc.h b/include/commproc.h index 7605713..76a62de 100644 --- a/include/commproc.h +++ b/include/commproc.h @@ -556,27 +556,6 @@ typedef struct scc_enet { #define SICR_ENET_CLKRT ((uint)0x00002600) #endif /* CONFIG_FPS850L, CONFIG_FPS860L */ -/*** GEN860T **********************************************************/ -#if defined(CONFIG_GEN860T) -#undef SCC_ENET -#define FEC_ENET - -#define PD_MII_TXD1 ((ushort)0x1000) /* PD 3 */ -#define PD_MII_TXD2 ((ushort)0x0800) /* PD 4 */ -#define PD_MII_TXD3 ((ushort)0x0400) /* PD 5 */ -#define PD_MII_RX_DV ((ushort)0x0200) /* PD 6 */ -#define PD_MII_RX_ERR ((ushort)0x0100) /* PD 7 */ -#define PD_MII_RX_CLK ((ushort)0x0080) /* PD 8 */ -#define PD_MII_TXD0 ((ushort)0x0040) /* PD 9 */ -#define PD_MII_RXD0 ((ushort)0x0020) /* PD 10 */ -#define PD_MII_TX_ERR ((ushort)0x0010) /* PD 11 */ -#define PD_MII_MDC ((ushort)0x0008) /* PD 12 */ -#define PD_MII_RXD1 ((ushort)0x0004) /* PD 13 */ -#define PD_MII_RXD2 ((ushort)0x0002) /* PD 14 */ -#define PD_MII_RXD3 ((ushort)0x0001) /* PD 15 */ -#define PD_MII_MASK ((ushort)0x1FFF) /* PD 3-15 */ -#endif /* CONFIG_GEN860T */ - /*** HERMES-PRO ******************************************************/ /* The HERMES-PRO uses the FEC on a MPC860T for Ethernet */ diff --git a/include/configs/GEN860T.h b/include/configs/GEN860T.h deleted file mode 100644 index fd6c976..0000000 --- a/include/configs/GEN860T.h +++ /dev/null @@ -1,712 +0,0 @@ -/* - * (C) Copyright 2000 - * Wolfgang Denk, DENX Software Engineering, wd@denx.de. - * Keith Outwater, keith_outwater@mvis.com - * - * SPDX-License-Identifier: GPL-2.0+ - */ - -/* - * board/config_GEN860T.h - board specific configuration options - */ - -#ifndef __CONFIG_GEN860T_H -#define __CONFIG_H - -/* - * High Level Configuration Options - */ -#define CONFIG_MPC860 -#define CONFIG_GEN860T - -#define CONFIG_SYS_TEXT_BASE 0x40000000 - -/* - * Identify the board - */ -#if !defined(CONFIG_SC) -#define CONFIG_IDENT_STRING " B2" -#else -#define CONFIG_IDENT_STRING " SC" -#endif - -/* - * Don't depend on the RTC clock to determine clock frequency - - * the 860's internal rtc uses a 32.768 KHz clock which is - * generated by the DS1337 - and the DS1337 clock can be turned off. - */ -#if !defined(CONFIG_SC) -#define CONFIG_8xx_GCLK_FREQ 66600000 -#else -#define CONFIG_8xx_GCLK_FREQ 48000000 -#endif - -/* - * The RS-232 console port is on SMC1 - */ -#define CONFIG_8xx_CONS_SMC1 -#define CONFIG_BAUDRATE 38400 - -/* - * Print console information - */ -#undef CONFIG_SYS_CONSOLE_INFO_QUIET - -/* - * Set the autoboot delay in seconds. A delay of -1 disables autoboot - */ -#define CONFIG_BOOTDELAY 5 - -/* - * Pass the clock frequency to the Linux kernel in units of MHz - */ -#define CONFIG_CLOCKS_IN_MHZ - -#define CONFIG_PREBOOT \ - "echo;echo" - -#undef CONFIG_BOOTARGS -#define CONFIG_BOOTCOMMAND \ - "bootp;" \ - "setenv bootargs root=/dev/nfs rw nfsroot=${serverip}:${rootpath} " \ - "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}:${hostname}::off; " \ - "bootm" - -/* - * Turn off echo for serial download by default. Allow baud rate to be changed - * for downloads - */ -#undef CONFIG_LOADS_ECHO -#define CONFIG_SYS_LOADS_BAUD_CHANGE - -/* - * Turn off the watchdog timer - */ -#undef CONFIG_WATCHDOG - -/* - * Do not reboot if a panic occurs - */ -#define CONFIG_PANIC_HANG - -/* - * Enable the status LED - */ -#define CONFIG_STATUS_LED - -/* - * Reset address. We pick an address such that when an instruction - * is executed at that address, a machine check exception occurs - */ -#define CONFIG_SYS_RESET_ADDRESS ((ulong) -1) - -/* - * BOOTP options - */ -#define CONFIG_BOOTP_SUBNETMASK -#define CONFIG_BOOTP_GATEWAY -#define CONFIG_BOOTP_HOSTNAME -#define CONFIG_BOOTP_BOOTPATH -#define CONFIG_BOOTP_BOOTFILESIZE - - -/* - * The GEN860T network interface uses the on-chip 10/100 FEC with - * an Intel LXT971A PHY connected to the 860T's MII. The PHY's - * MII address is hardwired on the board to zero. - */ -#define CONFIG_FEC_ENET -#define CONFIG_SYS_DISCOVER_PHY -#define CONFIG_MII -#define CONFIG_MII_INIT 1 -#define CONFIG_PHY_ADDR 0 - -/* - * Set default IP stuff just to get bootstrap entries into the - * environment so that we can source the full default environment. - */ -#define CONFIG_ETHADDR 9a:52:63:15:85:25 -#define CONFIG_SERVERIP 10.0.4.201 -#define CONFIG_IPADDR 10.0.4.111 - -/* - * This board has a 32 kibibyte EEPROM (Atmel AT24C256) connected to - * the MPC860T I2C interface. - */ -#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 -#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 6 /* 64 byte pages */ -#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 12 /* 10 mS w/ 20% margin */ -#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2 /* need 16 bit address */ -#define CONFIG_ENV_EEPROM_SIZE (32 * 1024) - -/* - * Enable I2C and select the hardware/software driver - */ -#define CONFIG_HARD_I2C 1 /* CPM based I2C */ -#undef CONFIG_SYS_I2C_SOFT /* Bit-banged I2C */ - -#ifdef CONFIG_HARD_I2C -#define CONFIG_SYS_I2C_SPEED 100000 /* clock speed in Hz */ -#define CONFIG_SYS_I2C_SLAVE 0xFE /* I2C slave address */ -#endif - -#ifdef CONFIG_SYS_I2C_SOFT -#define CONFIG_SYS_I2C -#define CONFIG_SYS_I2C_SOFT_SPEED 50000 -#define CONFIG_SYS_I2C_SOFT_SLAVE 0xFE -#define PB_SCL 0x00000020 /* PB 26 */ -#define PB_SDA 0x00000010 /* PB 27 */ -#define I2C_INIT (immr->im_cpm.cp_pbdir |= PB_SCL) -#define I2C_ACTIVE (immr->im_cpm.cp_pbdir |= PB_SDA) -#define I2C_TRISTATE (immr->im_cpm.cp_pbdir &= ~PB_SDA) -#define I2C_READ ((immr->im_cpm.cp_pbdat & PB_SDA) != 0) -#define I2C_SDA(bit) if (bit) \ - immr->im_cpm.cp_pbdat |= PB_SDA; \ - else \ - immr->im_cpm.cp_pbdat &= ~PB_SDA -#define I2C_SCL(bit) if (bit) \ - immr->im_cpm.cp_pbdat |= PB_SCL; \ - else \ - immr->im_cpm.cp_pbdat &= ~PB_SCL -#define I2C_DELAY udelay(5) /* 1/4 I2C clock duration */ -#endif - -/* - * Allow environment overwrites by anyone - */ -#define CONFIG_ENV_OVERWRITE - -#if !defined(CONFIG_SC) -/* - * The MPC860's internal RTC is horribly broken in rev D masks. Three - * internal MPC860T circuit nodes were inadvertently left floating; this - * causes KAPWR current in power down mode to be three orders of magnitude - * higher than specified in the datasheet (from 10 uA to 10 mA). No - * reasonable battery can keep that kind RTC running during powerdown for any - * length of time, so we use an external RTC on the I2C bus instead. - */ -#define CONFIG_RTC_DS1337 -#define CONFIG_SYS_I2C_RTC_ADDR 0x68 - -#else -/* - * No external RTC on SC variant, so we're stuck with the internal one. - */ -#define CONFIG_RTC_MPC8xx -#endif - -/* - * Power On Self Test support - */ -#define CONFIG_POST ( CONFIG_SYS_POST_CACHE | \ - CONFIG_SYS_POST_MEMORY | \ - CONFIG_SYS_POST_CPU | \ - CONFIG_SYS_POST_UART | \ - CONFIG_SYS_POST_SPR ) - - -/* - * Command line configuration. - */ -#include - -#define CONFIG_CMD_ASKENV -#define CONFIG_CMD_DHCP -#define CONFIG_CMD_I2C -#define CONFIG_CMD_EEPROM -#define CONFIG_CMD_REGINFO -#define CONFIG_CMD_IMMAP -#define CONFIG_CMD_ELF -#define CONFIG_CMD_DATE -#define CONFIG_CMD_FPGA -#define CONFIG_CMD_FPGA_LOADMK -#define CONFIG_CMD_MII -#define CONFIG_CMD_BEDBUG - -#ifdef CONFIG_POST -#define CONFIG_CMD_DIAG -#endif - -/* - * There is no IDE/PCMCIA hardware support on the board. - */ -#undef CONFIG_IDE_PCMCIA -#undef CONFIG_IDE_LED -#undef CONFIG_IDE_RESET - -/* - * Enable the call to misc_init_r() for miscellaneous platform - * dependent initialization. - */ -#define CONFIG_MISC_INIT_R - -/* - * Enable call to last_stage_init() so we can twiddle some LEDS :) - */ -#define CONFIG_LAST_STAGE_INIT - -/* - * Virtex2 FPGA configuration support - */ -#define CONFIG_FPGA_COUNT 1 -#define CONFIG_FPGA -#define CONFIG_FPGA_XILINX -#define CONFIG_FPGA_VIRTEX2 -#define CONFIG_SYS_FPGA_PROG_FEEDBACK - -/* - * Verbose help from command monitor. - */ -#define CONFIG_SYS_LONGHELP -#if !defined(CONFIG_SC) -#define CONFIG_SYS_PROMPT "B2> " -#else -#define CONFIG_SYS_PROMPT "SC> " -#endif - - -/* - * Use the "hush" command parser - */ -#define CONFIG_SYS_HUSH_PARSER - -/* - * Set buffer size for console I/O - */ -#if defined(CONFIG_CMD_KGDB) -#define CONFIG_SYS_CBSIZE 1024 -#else -#define CONFIG_SYS_CBSIZE 256 -#endif - -/* - * Print buffer size - */ -#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16) - -/* - * Maximum number of arguments that a command can accept - */ -#define CONFIG_SYS_MAXARGS 16 - -/* - * Boot argument buffer size - */ -#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE - -/* - * Default memory test range - */ -#define CONFIG_SYS_MEMTEST_START 0x0100000 -#define CONFIG_SYS_MEMTEST_END (CONFIG_SYS_MEMTEST_START + (128 * 1024)) - -/* - * Select the more full-featured memory test - */ -#define CONFIG_SYS_ALT_MEMTEST - -/* - * Default load address - */ -#define CONFIG_SYS_LOAD_ADDR 0x01000000 - -/* - * Device memory map (after SDRAM remap to 0x0): - * - * CS Device Base Addr Size - * ---------------------------------------------------- - * CS0* Flash 0x40000000 64 M - * CS1* SDRAM 0x00000000 16 M - * CS2* Disk-On-Chip 0x50000000 32 K - * CS3* FPGA 0x60000000 64 M - * CS4* SelectMap 0x70000000 32 K - * CS5* Mil-Std 1553 I/F 0x80000000 32 K - * CS6* Unused - * CS7* Unused - * IMMR 860T Registers 0xfff00000 - */ - -/* - * Base addresses and block sizes - */ -#define CONFIG_SYS_IMMR 0xFF000000 - -#define SDRAM_BASE 0x00000000 -#define SDRAM_SIZE (64 * 1024 * 1024) - -#define FLASH_BASE 0x40000000 -#define FLASH_SIZE (16 * 1024 * 1024) - -#define DOC_BASE 0x50000000 -#define DOC_SIZE (32 * 1024) - -#define FPGA_BASE 0x60000000 -#define FPGA_SIZE (64 * 1024 * 1024) - -#define SELECTMAP_BASE 0x70000000 -#define SELECTMAP_SIZE (32 * 1024) - -#define M1553_BASE 0x80000000 -#define M1553_SIZE (64 * 1024) - -/* - * Definitions for initial stack pointer and data area (in DPRAM) - */ -#define CONFIG_SYS_INIT_RAM_ADDR CONFIG_SYS_IMMR -#define CONFIG_SYS_INIT_RAM_SIZE 0x2F00 /* Size of used area in DPRAM */ -#define CONFIG_SYS_INIT_DATA_SIZE 64 /* # bytes reserved for initial data*/ -#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - CONFIG_SYS_INIT_DATA_SIZE) -#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET - -/* - * Start addresses for the final memory configuration - * (Set up by the startup code) - * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0 - */ -#define CONFIG_SYS_SDRAM_BASE SDRAM_BASE - -/* - * FLASH organization - */ -#define CONFIG_SYS_FLASH_BASE FLASH_BASE -#define CONFIG_SYS_FLASH_SIZE FLASH_SIZE -#define CONFIG_SYS_FLASH_SECT_SIZE (128 * 1024) -#define CONFIG_SYS_MAX_FLASH_BANKS 1 -#define CONFIG_SYS_MAX_FLASH_SECT 128 - -/* - * The timeout values are for an entire chip and are in milliseconds. - * Yes I know that the write timeout is huge. Accroding to the - * datasheet a single byte takes 630 uS (round to 1 ms) max at worst - * case VCC and temp after 100K programming cycles. It works out - * to 280 minutes (might as well be forever). - */ -#define CONFIG_SYS_FLASH_ERASE_TOUT (CONFIG_SYS_MAX_FLASH_SECT * 5000) -#define CONFIG_SYS_FLASH_WRITE_TOUT (CONFIG_SYS_MAX_FLASH_SECT * 128 * 1024 * 1) - -/* - * Allow direct writes to FLASH from tftp transfers (** dangerous **) - */ -#define CONFIG_SYS_DIRECT_FLASH_TFTP - -/* - * Reserve memory for U-Boot. - */ -#define CONFIG_SYS_MAX_UBOOT_SECTS 4 -#define CONFIG_SYS_MONITOR_LEN (CONFIG_SYS_MAX_UBOOT_SECTS * CONFIG_SYS_FLASH_SECT_SIZE) -#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_FLASH_BASE - -/* - * Select environment placement. NOTE that u-boot.lds must - * be edited if this is changed! - */ -#undef CONFIG_ENV_IS_IN_FLASH -#define CONFIG_ENV_IS_IN_EEPROM - -#if defined(CONFIG_ENV_IS_IN_EEPROM) -#define CONFIG_ENV_SIZE (2 * 1024) -#define CONFIG_ENV_OFFSET (CONFIG_ENV_EEPROM_SIZE - (8 * 1024)) -#else -#define CONFIG_ENV_SIZE 0x1000 -#define CONFIG_ENV_SECT_SIZE CONFIG_SYS_FLASH_SECT_SIZE - -/* - * This ultimately gets passed right into the linker script, so we have to - * use a number :( - */ -#define CONFIG_ENV_OFFSET 0x060000 -#endif - -/* - * Reserve memory for malloc() - */ -#define CONFIG_SYS_MALLOC_LEN (128 * 1024) - -/* - * For booting Linux, the board info and command line data - * have to be in the first 8 MB of memory, since this is - * the maximum mapped by the Linux kernel during initialization. - */ -#define CONFIG_SYS_BOOTMAPSZ (8 * 1024 * 1024) - -/* - * Cache Configuration - */ -#define CONFIG_SYS_CACHELINE_SIZE 16 /* For all MPC8xx CPUs */ -#if defined(CONFIG_CMD_KGDB) -#define CONFIG_SYS_CACHELINE_SHIFT 4 /* log base 2 of above value */ -#endif - -/*------------------------------------------------------------------------ - * SYPCR - System Protection Control UM 11-9 - * ----------------------------------------------------------------------- - * SYPCR can only be written once after reset! - * - * Software & Bus Monitor Timer max, Bus Monitor enable, SW Watchdog freeze - */ -#if defined(CONFIG_WATCHDOG) -#define CONFIG_SYS_SYPCR ( SYPCR_SWTC | \ - SYPCR_BMT | \ - SYPCR_BME | \ - SYPCR_SWF | \ - SYPCR_SWE | \ - SYPCR_SWRI | \ - SYPCR_SWP \ - ) -#else -#define CONFIG_SYS_SYPCR ( SYPCR_SWTC | \ - SYPCR_BMT | \ - SYPCR_BME | \ - SYPCR_SWF | \ - SYPCR_SWP \ - ) -#endif - -/*----------------------------------------------------------------------- - * SIUMCR - SIU Module Configuration UM 11-6 - *----------------------------------------------------------------------- - * Set debug pin mux, enable SPKROUT and GPLB5*. - */ -#define CONFIG_SYS_SIUMCR ( SIUMCR_DBGC11 | \ - SIUMCR_DBPC11 | \ - SIUMCR_MLRC11 | \ - SIUMCR_GB5E \ - ) - -/*----------------------------------------------------------------------- - * TBSCR - Time Base Status and Control UM 11-26 - *----------------------------------------------------------------------- - * Clear Reference Interrupt Status, Timebase freeze enabled - */ -#define CONFIG_SYS_TBSCR ( TBSCR_REFA | \ - TBSCR_REFB | \ - TBSCR_TBF \ - ) - -/*----------------------------------------------------------------------- - * RTCSC - Real-Time Clock Status and Control Register UM 11-27 - *----------------------------------------------------------------------- - */ -#define CONFIG_SYS_RTCSC ( RTCSC_SEC | \ - RTCSC_ALR | \ - RTCSC_RTF | \ - RTCSC_RTE \ - ) - -/*----------------------------------------------------------------------- - * PISCR - Periodic Interrupt Status and Control UM 11-31 - *----------------------------------------------------------------------- - * Clear Periodic Interrupt Status, Interrupt Timer freezing enabled - */ -#define CONFIG_SYS_PISCR ( PISCR_PS | \ - PISCR_PITF \ - ) - -/*----------------------------------------------------------------------- - * PLPRCR - PLL, Low-Power, and Reset Control Register UM 15-30 - *----------------------------------------------------------------------- - * Reset PLL lock status sticky bit, timer expired status bit and timer - * interrupt status bit. Set MF for 1:2:1 mode. - */ -#define CONFIG_SYS_PLPRCR ( ((0x1 << PLPRCR_MF_SHIFT) & PLPRCR_MF_MSK) | \ - PLPRCR_SPLSS | \ - PLPRCR_TEXPS | \ - PLPRCR_TMIST \ - ) - -/*----------------------------------------------------------------------- - * SCCR - System Clock and reset Control Register UM 15-27 - *----------------------------------------------------------------------- - * Set clock output, timebase and RTC source and divider, - * power management and some other internal clocks - */ -#define SCCR_MASK SCCR_EBDF11 - -#if !defined(CONFIG_SC) -#define CONFIG_SYS_SCCR ( SCCR_TBS | /* timebase = GCLK/2 */ \ - SCCR_COM00 | /* full strength CLKOUT */ \ - SCCR_DFSYNC00 | /* SYNCLK / 1 (normal) */ \ - SCCR_DFBRG00 | /* BRGCLK / 1 (normal) */ \ - SCCR_DFNL000 | \ - SCCR_DFNH000 \ - ) -#else -#define CONFIG_SYS_SCCR ( SCCR_TBS | /* timebase = GCLK/2 */ \ - SCCR_COM00 | /* full strength CLKOUT */ \ - SCCR_DFSYNC00 | /* SYNCLK / 1 (normal) */ \ - SCCR_DFBRG00 | /* BRGCLK / 1 (normal) */ \ - SCCR_DFNL000 | \ - SCCR_DFNH000 | \ - SCCR_RTDIV | \ - SCCR_RTSEL \ - ) -#endif - -/*----------------------------------------------------------------------- - * DER - Debug Enable Register UM 37-46 - *----------------------------------------------------------------------- - * Mask all events that can cause entry into debug mode - */ -#define CONFIG_SYS_DER 0 - -/* - * Initialize Memory Controller: - * - * BR0 and OR0 (FLASH memory) - */ -#define FLASH_BASE0_PRELIM FLASH_BASE - -/* - * Flash address mask - */ -#define CONFIG_SYS_PRELIM_OR_AM 0xfe000000 - -/* - * FLASH timing: - * 33 Mhz bus with ACS = 11, TRLX = 1, CSNT = 1, SCY = 3, EHTR = 1 - */ -#define CONFIG_SYS_OR_TIMING_FLASH ( OR_CSNT_SAM | \ - OR_ACS_DIV2 | \ - OR_BI | \ - OR_SCY_2_CLK | \ - OR_TRLX | \ - OR_EHTR \ - ) - -#define CONFIG_SYS_OR0_PRELIM ( CONFIG_SYS_PRELIM_OR_AM | \ - CONFIG_SYS_OR_TIMING_FLASH \ - ) - -#define CONFIG_SYS_BR0_PRELIM ( (FLASH_BASE0_PRELIM & BR_BA_MSK) | \ - BR_MS_GPCM | \ - BR_PS_8 | \ - BR_V \ - ) - -/* - * SDRAM configuration - */ -#define CONFIG_SYS_OR1_AM 0xfc000000 -#define CONFIG_SYS_OR1 ( (CONFIG_SYS_OR1_AM & OR_AM_MSK) | \ - OR_CSNT_SAM \ - ) - -#define CONFIG_SYS_BR1 ( (SDRAM_BASE & BR_BA_MSK) | \ - BR_MS_UPMA | \ - BR_PS_32 | \ - BR_V \ - ) - -/* - * Refresh rate 7.8 us (= 64 ms / 8K = 31.2 uS quad bursts) for one bank - * of 256 MBit SDRAM - */ -#define CONFIG_SYS_MPTPR_1BK_8K MPTPR_PTP_DIV16 - -/* - * Periodic timer for refresh @ 33 MHz system clock - */ -#define CONFIG_SYS_MAMR_PTA 64 - -/* - * MAMR settings for SDRAM - */ -#define CONFIG_SYS_MAMR_8COL ( (CONFIG_SYS_MAMR_PTA << MAMR_PTA_SHIFT) | \ - MAMR_PTAE | \ - MAMR_AMA_TYPE_1 | \ - MAMR_DSA_1_CYCL | \ - MAMR_G0CLA_A10 | \ - MAMR_RLFA_1X | \ - MAMR_WLFA_1X | \ - MAMR_TLFA_4X \ - ) - -/* - * CS2* configuration for Disk On Chip: - * 33 MHz bus with TRLX=1, ACS=11, CSNT=1, EBDF=1, SCY=2, EHTR=1, - * no burst. - */ -#define CONFIG_SYS_OR2_PRELIM ( (0xffff0000 & OR_AM_MSK) | \ - OR_CSNT_SAM | \ - OR_ACS_DIV2 | \ - OR_BI | \ - OR_SCY_2_CLK | \ - OR_TRLX | \ - OR_EHTR \ - ) - -#define CONFIG_SYS_BR2_PRELIM ( (DOC_BASE & BR_BA_MSK) | \ - BR_PS_8 | \ - BR_MS_GPCM | \ - BR_V \ - ) - -/* - * CS3* configuration for FPGA: - * 33 MHz bus with SCY=15, no burst. - * The FPGA uses TA and TEA to terminate bus cycles, but we - * clear SETA and set the cycle length to a large number so that - * the cycle will still complete even if there is a configuration - * error that prevents TA from asserting on FPGA accesss. - */ -#define CONFIG_SYS_OR3_PRELIM ( (0xfc000000 & OR_AM_MSK) | \ - OR_SCY_15_CLK | \ - OR_BI \ - ) - -#define CONFIG_SYS_BR3_PRELIM ( (FPGA_BASE & BR_BA_MSK) | \ - BR_PS_32 | \ - BR_MS_GPCM | \ - BR_V \ - ) -/* - * CS4* configuration for FPGA SelectMap configuration interface. - * 33 MHz bus, UPMB, no burst. Do not assert GPLB5 on falling edge - * of GCLK1_50 - */ -#define CONFIG_SYS_OR4_PRELIM ( (0xffff0000 & OR_AM_MSK) | \ - OR_G5LS | \ - OR_BI \ - ) - -#define CONFIG_SYS_BR4_PRELIM ( (SELECTMAP_BASE & BR_BA_MSK) | \ - BR_PS_8 | \ - BR_MS_UPMB | \ - BR_V \ - ) - -/* - * CS5* configuration for Mil-Std 1553 databus interface. - * 33 MHz bus, GPCM, no burst. - * The 1553 interface uses TA and TEA to terminate bus cycles, - * but we clear SETA and set the cycle length to a large number so that - * the cycle will still complete even if there is a configuration - * error that prevents TA from asserting on FPGA accesss. - */ -#define CONFIG_SYS_OR5_PRELIM ( (0xffff0000 & OR_AM_MSK) | \ - OR_SCY_15_CLK | \ - OR_EHTR | \ - OR_TRLX | \ - OR_CSNT_SAM | \ - OR_BI \ - ) - -#define CONFIG_SYS_BR5_PRELIM ( (M1553_BASE & BR_BA_MSK) | \ - BR_PS_16 | \ - BR_MS_GPCM | \ - BR_V \ - ) - -/* - * FEC interrupt assignment - */ -#define FEC_INTERRUPT SIU_LEVEL1 - -/* - * Sanity checks - */ -#if defined(CONFIG_SCC1_ENET) && defined(CONFIG_FEC_ENET) -#error Both CONFIG_SCC1_ENET and CONFIG_FEC_ENET configured -#endif - -#endif /* __CONFIG_GEN860T_H */ diff --git a/include/status_led.h b/include/status_led.h index c9d21d1..c1d2242 100644 --- a/include/status_led.h +++ b/include/status_led.h @@ -56,30 +56,6 @@ void status_led_set (int led, int state); # define STATUS_LED_BOOT 0 /* LED 0 used for boot status */ -/***** GEN860T *********************************************************/ -#elif defined(CONFIG_GEN860T) - -# define STATUS_LED_PAR im_ioport.iop_papar -# define STATUS_LED_DIR im_ioport.iop_padir -# define STATUS_LED_ODR im_ioport.iop_paodr -# define STATUS_LED_DAT im_ioport.iop_padat - -# define STATUS_LED_BIT 0x0800 /* Red LED 0 is on PA.4 */ -# define STATUS_LED_PERIOD (CONFIG_SYS_HZ / 4) -# define STATUS_LED_STATE STATUS_LED_OFF -# define STATUS_LED_BIT1 0x0400 /* Grn LED 1 is on PA.5 */ -# define STATUS_LED_PERIOD1 (CONFIG_SYS_HZ / 8) -# define STATUS_LED_STATE1 STATUS_LED_BLINKING -# define STATUS_LED_BIT2 0x0080 /* Red LED 2 is on PA.8 */ -# define STATUS_LED_PERIOD2 (CONFIG_SYS_HZ / 4) -# define STATUS_LED_STATE2 STATUS_LED_OFF -# define STATUS_LED_BIT3 0x0040 /* Grn LED 3 is on PA.9 */ -# define STATUS_LED_PERIOD3 (CONFIG_SYS_HZ / 4) -# define STATUS_LED_STATE3 STATUS_LED_OFF - -# define STATUS_LED_ACTIVE 1 /* LED on for bit == 1 */ -# define STATUS_LED_BOOT 1 /* Boot status on LED 1 */ - /***** IVMS8 **********************************************************/ #elif defined(CONFIG_IVMS8) -- 2.7.4