From 67a54566553d48d7ee45a0704d36b4fe8c4f13d2 Mon Sep 17 00:00:00 2001 From: Daniel Vetter Date: Sat, 20 Oct 2012 20:57:45 +0200 Subject: [PATCH] drm/i915: extract intel_dp_init_panel_power_sequencer That thing has grown way too big already. Also move around a comment to the right spot. Reviewed-by: Jesse Barnes Tested-by: Paulo Zanoni Signed-off-by: Daniel Vetter --- drivers/gpu/drm/i915/intel_dp.c | 223 +++++++++++++++++++++------------------- 1 file changed, 115 insertions(+), 108 deletions(-) diff --git a/drivers/gpu/drm/i915/intel_dp.c b/drivers/gpu/drm/i915/intel_dp.c index c1ed1af..01b67d9 100644 --- a/drivers/gpu/drm/i915/intel_dp.c +++ b/drivers/gpu/drm/i915/intel_dp.c @@ -2522,6 +2522,118 @@ intel_dp_add_properties(struct intel_dp *intel_dp, struct drm_connector *connect intel_attach_broadcast_rgb_property(connector); } +static void +intel_dp_init_panel_power_sequencer(struct drm_device *dev, + struct intel_dp *intel_dp) +{ + struct drm_i915_private *dev_priv = dev->dev_private; + struct edp_power_seq cur, vbt, spec, final; + u32 pp_on, pp_off, pp_div, pp; + + /* Workaround: Need to write PP_CONTROL with the unlock key as + * the very first thing. */ + pp = ironlake_get_pp_control(dev_priv); + I915_WRITE(PCH_PP_CONTROL, pp); + + pp_on = I915_READ(PCH_PP_ON_DELAYS); + pp_off = I915_READ(PCH_PP_OFF_DELAYS); + pp_div = I915_READ(PCH_PP_DIVISOR); + + /* Pull timing values out of registers */ + cur.t1_t3 = (pp_on & PANEL_POWER_UP_DELAY_MASK) >> + PANEL_POWER_UP_DELAY_SHIFT; + + cur.t8 = (pp_on & PANEL_LIGHT_ON_DELAY_MASK) >> + PANEL_LIGHT_ON_DELAY_SHIFT; + + cur.t9 = (pp_off & PANEL_LIGHT_OFF_DELAY_MASK) >> + PANEL_LIGHT_OFF_DELAY_SHIFT; + + cur.t10 = (pp_off & PANEL_POWER_DOWN_DELAY_MASK) >> + PANEL_POWER_DOWN_DELAY_SHIFT; + + cur.t11_t12 = ((pp_div & PANEL_POWER_CYCLE_DELAY_MASK) >> + PANEL_POWER_CYCLE_DELAY_SHIFT) * 1000; + + DRM_DEBUG_KMS("cur t1_t3 %d t8 %d t9 %d t10 %d t11_t12 %d\n", + cur.t1_t3, cur.t8, cur.t9, cur.t10, cur.t11_t12); + + vbt = dev_priv->edp.pps; + + /* Upper limits from eDP 1.3 spec. Note that we use the clunky units of + * our hw here, which are all in 100usec. */ + spec.t1_t3 = 210 * 10; + spec.t8 = 50 * 10; /* no limit for t8, use t7 instead */ + spec.t9 = 50 * 10; /* no limit for t9, make it symmetric with t8 */ + spec.t10 = 500 * 10; + /* This one is special and actually in units of 100ms, but zero + * based in the hw (so we need to add 100 ms). But the sw vbt + * table multiplies it with 1000 to make it in units of 100usec, + * too. */ + spec.t11_t12 = (510 + 100) * 10; + + DRM_DEBUG_KMS("vbt t1_t3 %d t8 %d t9 %d t10 %d t11_t12 %d\n", + vbt.t1_t3, vbt.t8, vbt.t9, vbt.t10, vbt.t11_t12); + + /* Use the max of the register settings and vbt. If both are + * unset, fall back to the spec limits. */ +#define assign_final(field) final.field = (max(cur.field, vbt.field) == 0 ? \ + spec.field : \ + max(cur.field, vbt.field)) + assign_final(t1_t3); + assign_final(t8); + assign_final(t9); + assign_final(t10); + assign_final(t11_t12); +#undef assign_final + +#define get_delay(field) (DIV_ROUND_UP(final.field, 10)) + intel_dp->panel_power_up_delay = get_delay(t1_t3); + intel_dp->backlight_on_delay = get_delay(t8); + intel_dp->backlight_off_delay = get_delay(t9); + intel_dp->panel_power_down_delay = get_delay(t10); + intel_dp->panel_power_cycle_delay = get_delay(t11_t12); +#undef get_delay + + /* And finally store the new values in the power sequencer. */ + pp_on = (final.t1_t3 << PANEL_POWER_UP_DELAY_SHIFT) | + (final.t8 << PANEL_LIGHT_ON_DELAY_SHIFT); + pp_off = (final.t9 << PANEL_LIGHT_OFF_DELAY_SHIFT) | + (final.t10 << PANEL_POWER_DOWN_DELAY_SHIFT); + /* Compute the divisor for the pp clock, simply match the Bspec + * formula. */ + pp_div = ((100 * intel_pch_rawclk(dev))/2 - 1) + << PP_REFERENCE_DIVIDER_SHIFT; + pp_div |= (DIV_ROUND_UP(final.t11_t12, 1000) + << PANEL_POWER_CYCLE_DELAY_SHIFT); + + /* Haswell doesn't have any port selection bits for the panel + * power sequencer any more. */ + if (HAS_PCH_IBX(dev) || HAS_PCH_CPT(dev)) { + if (is_cpu_edp(intel_dp)) + pp_on |= PANEL_POWER_PORT_DP_A; + else + pp_on |= PANEL_POWER_PORT_DP_D; + } + + I915_WRITE(PCH_PP_ON_DELAYS, pp_on); + I915_WRITE(PCH_PP_OFF_DELAYS, pp_off); + I915_WRITE(PCH_PP_DIVISOR, pp_div); + + + DRM_DEBUG_KMS("panel power up delay %d, power down delay %d, power cycle delay %d\n", + intel_dp->panel_power_up_delay, intel_dp->panel_power_down_delay, + intel_dp->panel_power_cycle_delay); + + DRM_DEBUG_KMS("backlight on delay %d, off delay %d\n", + intel_dp->backlight_on_delay, intel_dp->backlight_off_delay); + + DRM_DEBUG_KMS("panel power sequencer register settings: PP_ON %#x, PP_OFF %#x, PP_DIV %#x\n", + I915_READ(PCH_PP_ON_DELAYS), + I915_READ(PCH_PP_OFF_DELAYS), + I915_READ(PCH_PP_DIVISOR)); +} + void intel_dp_init(struct drm_device *dev, int output_reg, enum port port) { @@ -2636,117 +2748,12 @@ intel_dp_init(struct drm_device *dev, int output_reg, enum port port) break; } - /* Cache some DPCD data in the eDP case */ - if (is_edp(intel_dp)) { - struct edp_power_seq cur, vbt, spec, final; - u32 pp_on, pp_off, pp_div, pp; - - /* Workaround: Need to write PP_CONTROL with the unlock key as - * the very first thing. */ - pp = ironlake_get_pp_control(dev_priv); - I915_WRITE(PCH_PP_CONTROL, pp); - - pp_on = I915_READ(PCH_PP_ON_DELAYS); - pp_off = I915_READ(PCH_PP_OFF_DELAYS); - pp_div = I915_READ(PCH_PP_DIVISOR); - - /* Pull timing values out of registers */ - cur.t1_t3 = (pp_on & PANEL_POWER_UP_DELAY_MASK) >> - PANEL_POWER_UP_DELAY_SHIFT; - - cur.t8 = (pp_on & PANEL_LIGHT_ON_DELAY_MASK) >> - PANEL_LIGHT_ON_DELAY_SHIFT; - - cur.t9 = (pp_off & PANEL_LIGHT_OFF_DELAY_MASK) >> - PANEL_LIGHT_OFF_DELAY_SHIFT; - - cur.t10 = (pp_off & PANEL_POWER_DOWN_DELAY_MASK) >> - PANEL_POWER_DOWN_DELAY_SHIFT; - - cur.t11_t12 = ((pp_div & PANEL_POWER_CYCLE_DELAY_MASK) >> - PANEL_POWER_CYCLE_DELAY_SHIFT) * 1000; - - DRM_DEBUG_KMS("cur t1_t3 %d t8 %d t9 %d t10 %d t11_t12 %d\n", - cur.t1_t3, cur.t8, cur.t9, cur.t10, cur.t11_t12); - - vbt = dev_priv->edp.pps; - - /* Upper limits from eDP 1.3 spec. Note that we use the clunky - * units of our hw here, which are all in 100usec. */ - spec.t1_t3 = 210 * 10; - spec.t8 = 50 * 10; /* no limit for t8, use t7 instead */ - spec.t9 = 50 * 10; /* no limit for t9, make it symmetric with t8 */ - spec.t10 = 500 * 10; - /* This one is special and actually in units of 100ms, but zero - * based in the hw (so we need to add 100 ms). But the sw vbt - * table multiplies it with 1000 to make it in units of 100usec, - * too. */ - spec.t11_t12 = (510 + 100) * 10; - - DRM_DEBUG_KMS("vbt t1_t3 %d t8 %d t9 %d t10 %d t11_t12 %d\n", - vbt.t1_t3, vbt.t8, vbt.t9, vbt.t10, vbt.t11_t12); - - /* Use the max of the register settings and vbt. If both are - * unset, fall back to the spec limits. */ -#define assign_final(field) final.field = (max(cur.field, vbt.field) == 0 ? \ - spec.field : \ - max(cur.field, vbt.field)) - assign_final(t1_t3); - assign_final(t8); - assign_final(t9); - assign_final(t10); - assign_final(t11_t12); -#undef assign_final - -#define get_delay(field) (DIV_ROUND_UP(final.field, 10)) - intel_dp->panel_power_up_delay = get_delay(t1_t3); - intel_dp->backlight_on_delay = get_delay(t8); - intel_dp->backlight_off_delay = get_delay(t9); - intel_dp->panel_power_down_delay = get_delay(t10); - intel_dp->panel_power_cycle_delay = get_delay(t11_t12); -#undef get_delay - - /* And finally store the new values in the power sequencer. */ - pp_on = (final.t1_t3 << PANEL_POWER_UP_DELAY_SHIFT) | - (final.t8 << PANEL_LIGHT_ON_DELAY_SHIFT); - pp_off = (final.t9 << PANEL_LIGHT_OFF_DELAY_SHIFT) | - (final.t10 << PANEL_POWER_DOWN_DELAY_SHIFT); - /* Compute the divisor for the pp clock, simply match the Bspec - * formula. */ - pp_div = ((100 * intel_pch_rawclk(dev))/2 - 1) - << PP_REFERENCE_DIVIDER_SHIFT; - pp_div |= (DIV_ROUND_UP(final.t11_t12, 1000) - << PANEL_POWER_CYCLE_DELAY_SHIFT); - - /* Haswell doesn't have any port selection bits for the panel - * power sequence any more. */ - if (HAS_PCH_IBX(dev) || HAS_PCH_CPT(dev)) { - if (is_cpu_edp(intel_dp)) - pp_on |= PANEL_POWER_PORT_DP_A; - else - pp_on |= PANEL_POWER_PORT_DP_D; - } - - I915_WRITE(PCH_PP_ON_DELAYS, pp_on); - I915_WRITE(PCH_PP_OFF_DELAYS, pp_off); - I915_WRITE(PCH_PP_DIVISOR, pp_div); - - - DRM_DEBUG_KMS("panel power up delay %d, power down delay %d, power cycle delay %d\n", - intel_dp->panel_power_up_delay, intel_dp->panel_power_down_delay, - intel_dp->panel_power_cycle_delay); - - DRM_DEBUG_KMS("backlight on delay %d, off delay %d\n", - intel_dp->backlight_on_delay, intel_dp->backlight_off_delay); - - DRM_DEBUG_KMS("panel power sequencer register settings: PP_ON %#x, PP_OFF %#x, PP_DIV %#x\n", - I915_READ(PCH_PP_ON_DELAYS), - I915_READ(PCH_PP_OFF_DELAYS), - I915_READ(PCH_PP_DIVISOR)); - } + if (is_edp(intel_dp)) + intel_dp_init_panel_power_sequencer(dev, intel_dp); intel_dp_i2c_init(intel_dp, intel_connector, name); + /* Cache DPCD and EDID for edp. */ if (is_edp(intel_dp)) { bool ret; struct drm_display_mode *scan; -- 2.7.4