From 36252668c14ca14691d40c3455849ac5d8a60b62 Mon Sep 17 00:00:00 2001
From: Chen-Yu Tsai <wens@csie.org>
Date: Sat, 2 Dec 2017 00:27:33 +0800
Subject: [PATCH] arm64: dts: allwinner: a64: bananapi-m64: Add LED device node

The Bananapi-M64 has 3 LEDS in red, green, and blue. These are toggled
via GPIO lines, which drive transistors that control current across the
LEDS. The red LED is by default on, via an additional pull-up on the
control line. We consider this means that it is a power indicator.
So we set the "default-on" property for it.

The pingroups the GPIO lines belong to require external regulators be
enabled to be able to drive the GPIO high. These regulators also have
other purposes. However the pin controller does not have bindings for
regulators. Here we just set them to always-on.

Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
---
 .../boot/dts/allwinner/sun50i-a64-bananapi-m64.dts | 36 ++++++++++++++++++++++
 1 file changed, 36 insertions(+)

diff --git a/arch/arm64/boot/dts/allwinner/sun50i-a64-bananapi-m64.dts b/arch/arm64/boot/dts/allwinner/sun50i-a64-bananapi-m64.dts
index 45bdbfb..1abb450 100644
--- a/arch/arm64/boot/dts/allwinner/sun50i-a64-bananapi-m64.dts
+++ b/arch/arm64/boot/dts/allwinner/sun50i-a64-bananapi-m64.dts
@@ -60,6 +60,26 @@
 		stdout-path = "serial0:115200n8";
 	};
 
+	leds {
+		compatible = "gpio-leds";
+
+		pwr-led {
+			label = "bananapi-m64:red:pwr";
+			gpios = <&pio 3 24 GPIO_ACTIVE_HIGH>; /* PD24 */
+			default-state = "on";
+		};
+
+		green {
+			label = "bananapi-m64:green:user";
+			gpios = <&pio 4 14 GPIO_ACTIVE_HIGH>; /* PE14 */
+		};
+
+		blue {
+			label = "bananapi-m64:blue:user";
+			gpios = <&pio 4 15 GPIO_ACTIVE_HIGH>; /* PE15 */
+		};
+	};
+
 	wifi_pwrseq: wifi_pwrseq {
 		compatible = "mmc-pwrseq-simple";
 		reset-gpios = <&r_pio 0 2 GPIO_ACTIVE_LOW>; /* PL2 */
@@ -152,6 +172,17 @@
 
 #include "axp803.dtsi"
 
+&reg_aldo1 {
+	/*
+	 * This regulator also drives the PE pingroup GPIOs,
+	 * which also controls two LEDs.
+	 */
+	regulator-always-on;
+	regulator-min-microvolt = <2800000>;
+	regulator-max-microvolt = <2800000>;
+	regulator-name = "afvcc-csi";
+};
+
 &reg_aldo2 {
 	regulator-always-on;
 	regulator-min-microvolt = <1800000>;
@@ -167,6 +198,11 @@
 };
 
 &reg_dc1sw {
+	/*
+	 * This regulator also indirectly drives the PD pingroup GPIOs,
+	 * which also controls the power LED.
+	 */
+	regulator-always-on;
 	regulator-name = "vcc-phy";
 };
 
-- 
2.7.4