From 19d95e1afae11b1a414491fd62e89a47cceadea9 Mon Sep 17 00:00:00 2001 From: Kevin Wells Date: Tue, 27 Jul 2010 08:44:37 -0700 Subject: [PATCH] ARM: LPC32XX: Phytec 3250 platform support MIME-Version: 1.0 Content-Type: text/plain; charset=utf8 Content-Transfer-Encoding: 8bit Platform support file for the PHY3250 mach id Signed-off-by: Kevin Wells Signed-off-by: Uwe Kleine-König --- arch/arm/mach-lpc32xx/phy3250.c | 397 ++++++++++++++++++++++++++++++++++++++++ 1 file changed, 397 insertions(+) create mode 100644 arch/arm/mach-lpc32xx/phy3250.c diff --git a/arch/arm/mach-lpc32xx/phy3250.c b/arch/arm/mach-lpc32xx/phy3250.c new file mode 100644 index 0000000..bc9a42d --- /dev/null +++ b/arch/arm/mach-lpc32xx/phy3250.c @@ -0,0 +1,397 @@ +/* + * arch/arm/mach-lpc32xx/phy3250.c + * + * Author: Kevin Wells + * + * Copyright (C) 2010 NXP Semiconductors + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + */ + +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include + +#include +#include +#include + +#include +#include +#include "common.h" + +/* + * Mapped GPIOLIB GPIOs + */ +#define SPI0_CS_GPIO LPC32XX_GPIO(LPC32XX_GPIO_P3_GRP, 5) +#define LCD_POWER_GPIO LPC32XX_GPIO(LPC32XX_GPO_P3_GRP, 0) +#define BKL_POWER_GPIO LPC32XX_GPIO(LPC32XX_GPO_P3_GRP, 4) +#define LED_GPIO LPC32XX_GPIO(LPC32XX_GPO_P3_GRP, 1) + +/* + * AMBA LCD controller + */ +static struct clcd_panel conn_lcd_panel = { + .mode = { + .name = "QVGA portrait", + .refresh = 60, + .xres = 240, + .yres = 320, + .pixclock = 191828, + .left_margin = 22, + .right_margin = 11, + .upper_margin = 2, + .lower_margin = 1, + .hsync_len = 5, + .vsync_len = 2, + .sync = 0, + .vmode = FB_VMODE_NONINTERLACED, + }, + .width = -1, + .height = -1, + .tim2 = (TIM2_IVS | TIM2_IHS), + .cntl = (CNTL_BGR | CNTL_LCDTFT | CNTL_LCDVCOMP(1) | + CNTL_LCDBPP16_565), + .bpp = 16, +}; +#define PANEL_SIZE (3 * SZ_64K) + +static int lpc32xx_clcd_setup(struct clcd_fb *fb) +{ + dma_addr_t dma; + + fb->fb.screen_base = dma_alloc_writecombine(&fb->dev->dev, + PANEL_SIZE, &dma, GFP_KERNEL); + if (!fb->fb.screen_base) { + printk(KERN_ERR "CLCD: unable to map framebuffer\n"); + return -ENOMEM; + } + + fb->fb.fix.smem_start = dma; + fb->fb.fix.smem_len = PANEL_SIZE; + fb->panel = &conn_lcd_panel; + + if (gpio_request(LCD_POWER_GPIO, "LCD power")) + printk(KERN_ERR "Error requesting gpio %u", + LCD_POWER_GPIO); + else if (gpio_direction_output(LCD_POWER_GPIO, 1)) + printk(KERN_ERR "Error setting gpio %u to output", + LCD_POWER_GPIO); + + if (gpio_request(BKL_POWER_GPIO, "LCD backlight power")) + printk(KERN_ERR "Error requesting gpio %u", + BKL_POWER_GPIO); + else if (gpio_direction_output(BKL_POWER_GPIO, 1)) + printk(KERN_ERR "Error setting gpio %u to output", + BKL_POWER_GPIO); + + return 0; +} + +static int lpc32xx_clcd_mmap(struct clcd_fb *fb, struct vm_area_struct *vma) +{ + return dma_mmap_writecombine(&fb->dev->dev, vma, + fb->fb.screen_base, fb->fb.fix.smem_start, + fb->fb.fix.smem_len); +} + +static void lpc32xx_clcd_remove(struct clcd_fb *fb) +{ + dma_free_writecombine(&fb->dev->dev, fb->fb.fix.smem_len, + fb->fb.screen_base, fb->fb.fix.smem_start); +} + +/* + * On some early LCD modules (1307.0), the backlight logic is inverted. + * For those board variants, swap the disable and enable states for + * BKL_POWER_GPIO. +*/ +static void clcd_disable(struct clcd_fb *fb) +{ + gpio_set_value(BKL_POWER_GPIO, 0); + gpio_set_value(LCD_POWER_GPIO, 0); +} + +static void clcd_enable(struct clcd_fb *fb) +{ + gpio_set_value(BKL_POWER_GPIO, 1); + gpio_set_value(LCD_POWER_GPIO, 1); +} + +static struct clcd_board lpc32xx_clcd_data = { + .name = "Phytec LCD", + .check = clcdfb_check, + .decode = clcdfb_decode, + .disable = clcd_disable, + .enable = clcd_enable, + .setup = lpc32xx_clcd_setup, + .mmap = lpc32xx_clcd_mmap, + .remove = lpc32xx_clcd_remove, +}; + +static struct amba_device lpc32xx_clcd_device = { + .dev = { + .coherent_dma_mask = ~0, + .init_name = "dev:clcd", + .platform_data = &lpc32xx_clcd_data, + }, + .res = { + .start = LPC32XX_LCD_BASE, + .end = (LPC32XX_LCD_BASE + SZ_4K - 1), + .flags = IORESOURCE_MEM, + }, + .dma_mask = ~0, + .irq = {IRQ_LPC32XX_LCD, NO_IRQ}, +}; + +/* + * AMBA SSP (SPI) + */ +static void phy3250_spi_cs_set(u32 control) +{ + gpio_set_value(SPI0_CS_GPIO, (int) control); +} + +static struct pl022_config_chip spi0_chip_info = { + .lbm = LOOPBACK_DISABLED, + .com_mode = INTERRUPT_TRANSFER, + .iface = SSP_INTERFACE_MOTOROLA_SPI, + .hierarchy = SSP_MASTER, + .slave_tx_disable = 0, + .endian_tx = SSP_TX_LSB, + .endian_rx = SSP_RX_LSB, + .data_size = SSP_DATA_BITS_8, + .rx_lev_trig = SSP_RX_4_OR_MORE_ELEM, + .tx_lev_trig = SSP_TX_4_OR_MORE_EMPTY_LOC, + .clk_phase = SSP_CLK_FIRST_EDGE, + .clk_pol = SSP_CLK_POL_IDLE_LOW, + .ctrl_len = SSP_BITS_8, + .wait_state = SSP_MWIRE_WAIT_ZERO, + .duplex = SSP_MICROWIRE_CHANNEL_FULL_DUPLEX, + .cs_control = phy3250_spi_cs_set, +}; + +static struct pl022_ssp_controller lpc32xx_ssp0_data = { + .bus_id = 0, + .num_chipselect = 1, + .enable_dma = 0, +}; + +static struct amba_device lpc32xx_ssp0_device = { + .dev = { + .coherent_dma_mask = ~0, + .init_name = "dev:ssp0", + .platform_data = &lpc32xx_ssp0_data, + }, + .res = { + .start = LPC32XX_SSP0_BASE, + .end = (LPC32XX_SSP0_BASE + SZ_4K - 1), + .flags = IORESOURCE_MEM, + }, + .dma_mask = ~0, + .irq = {IRQ_LPC32XX_SSP0, NO_IRQ}, +}; + +/* AT25 driver registration */ +static int __init phy3250_spi_board_register(void) +{ +#if defined(CONFIG_SPI_SPIDEV) || defined(CONFIG_SPI_SPIDEV_MODULE) + static struct spi_board_info info[] = { + { + .modalias = "spidev", + .max_speed_hz = 5000000, + .bus_num = 0, + .chip_select = 0, + .controller_data = &spi0_chip_info, + }, + }; + +#else + static struct spi_eeprom eeprom = { + .name = "at25256a", + .byte_len = 0x8000, + .page_size = 64, + .flags = EE_ADDR2, + }; + + static struct spi_board_info info[] = { + { + .modalias = "at25", + .max_speed_hz = 5000000, + .bus_num = 0, + .chip_select = 0, + .platform_data = &eeprom, + .controller_data = &spi0_chip_info, + }, + }; +#endif + return spi_register_board_info(info, ARRAY_SIZE(info)); +} +arch_initcall(phy3250_spi_board_register); + +static struct i2c_board_info __initdata phy3250_i2c_board_info[] = { + { + I2C_BOARD_INFO("pcf8563", 0x51), + }, +}; + +static struct gpio_led phy_leds[] = { + { + .name = "led0", + .gpio = LED_GPIO, + .active_low = 1, + .default_trigger = "heartbeat", + }, +}; + +static struct gpio_led_platform_data led_data = { + .leds = phy_leds, + .num_leds = ARRAY_SIZE(phy_leds), +}; + +static struct platform_device lpc32xx_gpio_led_device = { + .name = "leds-gpio", + .id = -1, + .dev.platform_data = &led_data, +}; + +static struct platform_device *phy3250_devs[] __initdata = { + &lpc32xx_i2c0_device, + &lpc32xx_i2c1_device, + &lpc32xx_i2c2_device, + &lpc32xx_watchdog_device, + &lpc32xx_gpio_led_device, +}; + +static struct amba_device *amba_devs[] __initdata = { + &lpc32xx_clcd_device, + &lpc32xx_ssp0_device, +}; + +/* + * Board specific functions + */ +static void __init phy3250_board_init(void) +{ + u32 tmp; + int i; + + lpc32xx_gpio_init(); + + /* Register GPIOs used on this board */ + if (gpio_request(SPI0_CS_GPIO, "spi0 cs")) + printk(KERN_ERR "Error requesting gpio %u", + SPI0_CS_GPIO); + else if (gpio_direction_output(SPI0_CS_GPIO, 1)) + printk(KERN_ERR "Error setting gpio %u to output", + SPI0_CS_GPIO); + + /* Setup network interface for RMII mode */ + tmp = __raw_readl(LPC32XX_CLKPWR_MACCLK_CTRL); + tmp &= ~LPC32XX_CLKPWR_MACCTRL_PINS_MSK; + tmp |= LPC32XX_CLKPWR_MACCTRL_USE_RMII_PINS; + __raw_writel(tmp, LPC32XX_CLKPWR_MACCLK_CTRL); + + /* Setup SLC NAND controller muxing */ + __raw_writel(LPC32XX_CLKPWR_NANDCLK_SEL_SLC, + LPC32XX_CLKPWR_NAND_CLK_CTRL); + + /* Setup LCD muxing to RGB565 */ + tmp = __raw_readl(LPC32XX_CLKPWR_LCDCLK_CTRL) & + ~(LPC32XX_CLKPWR_LCDCTRL_LCDTYPE_MSK | + LPC32XX_CLKPWR_LCDCTRL_PSCALE_MSK); + tmp |= LPC32XX_CLKPWR_LCDCTRL_LCDTYPE_TFT16; + __raw_writel(tmp, LPC32XX_CLKPWR_LCDCLK_CTRL); + + /* Set up I2C pull levels */ + tmp = __raw_readl(LPC32XX_CLKPWR_I2C_CLK_CTRL); + tmp |= LPC32XX_CLKPWR_I2CCLK_USBI2CHI_DRIVE | + LPC32XX_CLKPWR_I2CCLK_I2C2HI_DRIVE; + __raw_writel(tmp, LPC32XX_CLKPWR_I2C_CLK_CTRL); + + /* Disable IrDA pulsing support on UART6 */ + tmp = __raw_readl(LPC32XX_UARTCTL_CTRL); + tmp |= LPC32XX_UART_UART6_IRDAMOD_BYPASS; + __raw_writel(tmp, LPC32XX_UARTCTL_CTRL); + + /* Enable DMA for I2S1 channel */ + tmp = __raw_readl(LPC32XX_CLKPWR_I2S_CLK_CTRL); + tmp = LPC32XX_CLKPWR_I2SCTRL_I2S1_USE_DMA; + __raw_writel(tmp, LPC32XX_CLKPWR_I2S_CLK_CTRL); + + lpc32xx_serial_init(); + + /* + * AMBA peripheral clocks need to be enabled prior to AMBA device + * detection or a data fault will occur, so enable the clocks + * here. However, we don't want to enable them if the peripheral + * isn't included in the image + */ +#ifdef CONFIG_FB_ARMCLCD + tmp = __raw_readl(LPC32XX_CLKPWR_LCDCLK_CTRL); + __raw_writel((tmp | LPC32XX_CLKPWR_LCDCTRL_CLK_EN), + LPC32XX_CLKPWR_LCDCLK_CTRL); +#endif +#ifdef CONFIG_SPI_PL022 + tmp = __raw_readl(LPC32XX_CLKPWR_SSP_CLK_CTRL); + __raw_writel((tmp | LPC32XX_CLKPWR_SSPCTRL_SSPCLK0_EN), + LPC32XX_CLKPWR_SSP_CLK_CTRL); +#endif + + platform_add_devices(phy3250_devs, ARRAY_SIZE(phy3250_devs)); + for (i = 0; i < ARRAY_SIZE(amba_devs); i++) { + struct amba_device *d = amba_devs[i]; + amba_device_register(d, &iomem_resource); + } + + /* Test clock needed for UDA1380 initial init */ + __raw_writel(LPC32XX_CLKPWR_TESTCLK2_SEL_MOSC | + LPC32XX_CLKPWR_TESTCLK_TESTCLK2_EN, + LPC32XX_CLKPWR_TEST_CLK_SEL); + + i2c_register_board_info(0, phy3250_i2c_board_info, + ARRAY_SIZE(phy3250_i2c_board_info)); +} + +static int __init lpc32xx_display_uid(void) +{ + u32 uid[4]; + + lpc32xx_get_uid(uid); + + printk(KERN_INFO "LPC32XX unique ID: %08x%08x%08x%08x\n", + uid[3], uid[2], uid[1], uid[0]); + + return 1; +} +arch_initcall(lpc32xx_display_uid); + +MACHINE_START(PHY3250, "Phytec 3250 board with the LPC3250 Microcontroller") + /* Maintainer: Kevin Wells, NXP Semiconductors */ + .phys_io = LPC32XX_UART5_BASE, + .io_pg_offst = ((IO_ADDRESS(LPC32XX_UART5_BASE))>>18) & 0xfffc, + .boot_params = 0x80000100, + .map_io = lpc32xx_map_io, + .init_irq = lpc32xx_init_irq, + .timer = &lpc32xx_timer, + .init_machine = phy3250_board_init, +MACHINE_END -- 2.7.4