From 169582025adc8892ec0813f52f6d643055b3e9dc Mon Sep 17 00:00:00 2001 From: Julien Panis Date: Fri, 1 Jul 2022 14:30:11 +0200 Subject: [PATCH] arm64: mach-k3: am625_init: Probe ESM nodes On AM62x devices, main ESM error event outputs can be routed to MCU ESM as inputs. So, two ESM device nodes are expected in the device tree : one for main ESM and another one for MCU ESM. MCU ESM error output can trigger the reset logic to reset the device when CTRLMMR_MCU_RST_CTRL:MCU_ESM_ERROR_RESET_EN_Z is set to '0'. Signed-off-by: Julien Panis --- arch/arm/mach-k3/am625_init.c | 23 +++++++++++++++++++++++ arch/arm/mach-k3/include/mach/am62_hardware.h | 3 +++ 2 files changed, 26 insertions(+) diff --git a/arch/arm/mach-k3/am625_init.c b/arch/arm/mach-k3/am625_init.c index 0d95259..dfd95b8 100644 --- a/arch/arm/mach-k3/am625_init.c +++ b/arch/arm/mach-k3/am625_init.c @@ -64,6 +64,15 @@ static void ctrl_mmr_unlock(void) mmr_unlock(PADCFG_MMR1_BASE, 1); } +static __maybe_unused void enable_mcu_esm_reset(void) +{ + /* Set CTRLMMR_MCU_RST_CTRL:MCU_ESM_ERROR_RST_EN_Z to '0' (low active) */ + u32 stat = readl(CTRLMMR_MCU_RST_CTRL); + + stat &= RST_CTRL_ESM_ERROR_RST_EN_Z_MASK; + writel(stat, CTRLMMR_MCU_RST_CTRL); +} + void board_init_f(ulong dummy) { struct udevice *dev; @@ -142,6 +151,20 @@ void board_init_f(ulong dummy) /* Output System Firmware version info */ k3_sysfw_print_ver(); + if (IS_ENABLED(CONFIG_ESM_K3)) { + /* Probe/configure ESM0 */ + ret = uclass_get_device_by_name(UCLASS_MISC, "esm@420000", &dev); + if (ret) + printf("esm main init failed: %d\n", ret); + + /* Probe/configure MCUESM */ + ret = uclass_get_device_by_name(UCLASS_MISC, "esm@4100000", &dev); + if (ret) + printf("esm mcu init failed: %d\n", ret); + + enable_mcu_esm_reset(); + } + #if defined(CONFIG_K3_AM64_DDRSS) ret = uclass_get_device(UCLASS_RAM, 0, &dev); if (ret) diff --git a/arch/arm/mach-k3/include/mach/am62_hardware.h b/arch/arm/mach-k3/include/mach/am62_hardware.h index cfabd20..9118d05 100644 --- a/arch/arm/mach-k3/include/mach/am62_hardware.h +++ b/arch/arm/mach-k3/include/mach/am62_hardware.h @@ -29,6 +29,7 @@ #define MAIN_DEVSTAT_BACKUP_BOOTMODE_SHIFT 10 #define MAIN_DEVSTAT_BACKUP_BOOTMODE_CFG_MASK BIT(13) #define MAIN_DEVSTAT_BACKUP_BOOTMODE_CFG_SHIFT 13 +#define RST_CTRL_ESM_ERROR_RST_EN_Z_MASK (~BIT(17)) /* Primary Bootmode MMC Config macros */ #define MAIN_DEVSTAT_PRIMARY_MMC_PORT_MASK 0x4 @@ -67,6 +68,8 @@ #define MCU_CTRL_DEVICE_CLKOUT_32K_CTRL (MCU_CTRL_MMR0_BASE + 0x8058) #define MCU_CTRL_DEVICE_CLKOUT_LFOSC_SELECT_VAL (0x3) +#define CTRLMMR_MCU_RST_CTRL (MCU_CTRL_MMR0_BASE + 0x18170) + #define ROM_ENTENDED_BOOT_DATA_INFO 0x43c3f1e0 /* Use Last 2K as Scratch pad */ -- 2.7.4