From 0e5a6f27036e93110d3710d489fcc1408a674e62 Mon Sep 17 00:00:00 2001
From: Sumit Semwal <sumit.semwal@linaro.org>
Date: Mon, 5 Apr 2021 01:14:37 +0530
Subject: [PATCH] arm64: dts: qcom: sdm845-xiaomi-beryllium: Add DSI and panel
 bits

Enabling the Display panel for beryllium requires DSI
labibb regulators and panel dts nodes to be added.
It is also required to keep some of the regulators as
always-on.

Signed-off-by: Sumit Semwal <sumit.semwal@linaro.org>
Signed-off-by: Amit Pundir <amit.pundir@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Link: https://lore.kernel.org/r/20210404194437.537011-1-amit.pundir@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
---
 .../boot/dts/qcom/sdm845-xiaomi-beryllium.dts      | 71 ++++++++++++++++++++++
 1 file changed, 71 insertions(+)

diff --git a/arch/arm64/boot/dts/qcom/sdm845-xiaomi-beryllium.dts b/arch/arm64/boot/dts/qcom/sdm845-xiaomi-beryllium.dts
index 86cbae6..7d02942 100644
--- a/arch/arm64/boot/dts/qcom/sdm845-xiaomi-beryllium.dts
+++ b/arch/arm64/boot/dts/qcom/sdm845-xiaomi-beryllium.dts
@@ -157,6 +157,14 @@
 			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
 		};
 
+		vreg_l14a_1p8: ldo14 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+			regulator-boot-on;
+			regulator-always-on;
+		};
+
 		vreg_l17a_1p3: ldo17 {
 			regulator-min-microvolt = <1304000>;
 			regulator-max-microvolt = <1304000>;
@@ -191,6 +199,7 @@
 			regulator-min-microvolt = <1200000>;
 			regulator-max-microvolt = <1200000>;
 			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+			regulator-boot-on;
 		};
 	};
 };
@@ -200,6 +209,43 @@
 	firmware-name = "qcom/sdm845/cdsp.mdt";
 };
 
+&dsi0 {
+	status = "okay";
+	vdda-supply = <&vreg_l26a_1p2>;
+
+	#address-cells = <1>;
+	#size-cells = <0>;
+
+	panel@0 {
+		compatible = "tianma,fhd-video";
+		reg = <0>;
+		vddi0-supply = <&vreg_l14a_1p8>;
+		vddpos-supply = <&lab>;
+		vddneg-supply = <&ibb>;
+
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		reset-gpios = <&tlmm 6 GPIO_ACTIVE_LOW>;
+
+		port {
+			tianma_nt36672a_in_0: endpoint {
+				remote-endpoint = <&dsi0_out>;
+			};
+		};
+	};
+};
+
+&dsi0_out {
+	remote-endpoint = <&tianma_nt36672a_in_0>;
+	data-lanes = <0 1 2 3>;
+};
+
+&dsi0_phy {
+	status = "okay";
+	vdds-supply = <&vreg_l1a_0p875>;
+};
+
 &gcc {
 	protected-clocks = <GCC_QSPI_CORE_CLK>,
 			   <GCC_QSPI_CORE_CLK_SRC>,
@@ -215,6 +261,31 @@
 	};
 };
 
+&ibb {
+	regulator-min-microvolt = <4600000>;
+	regulator-max-microvolt = <6000000>;
+	regulator-over-current-protection;
+	regulator-pull-down;
+	regulator-soft-start;
+	qcom,discharge-resistor-kohms = <300>;
+};
+
+&lab {
+	regulator-min-microvolt = <4600000>;
+	regulator-max-microvolt = <6000000>;
+	regulator-over-current-protection;
+	regulator-pull-down;
+	regulator-soft-start;
+};
+
+&mdss {
+	status = "okay";
+};
+
+&mdss_mdp {
+	status = "okay";
+};
+
 &mss_pil {
 	status = "okay";
 	firmware-name = "qcom/sdm845/mba.mbn", "qcom/sdm845/modem.mdt";
-- 
2.7.4