From 0d19672e7807d7d365ca3b317f4b2d0db6847ca6 Mon Sep 17 00:00:00 2001 From: Aaro Koskinen Date: Fri, 2 Sep 2016 23:44:20 +0300 Subject: [PATCH] MIPS: Octeon: Delete legacy code for PHY access PHY access through the board helper is impossible with the current drivers, so delete this code. Signed-off-by: Aaro Koskinen Cc: David Daney Cc: linux-mips@linux-mips.org Patchwork: https://patchwork.linux-mips.org/patch/14205/ Signed-off-by: Ralf Baechle --- .../cavium-octeon/executive/cvmx-helper-board.c | 108 +-------------------- 1 file changed, 2 insertions(+), 106 deletions(-) diff --git a/arch/mips/cavium-octeon/executive/cvmx-helper-board.c b/arch/mips/cavium-octeon/executive/cvmx-helper-board.c index 5572e39..bc37266 100644 --- a/arch/mips/cavium-octeon/executive/cvmx-helper-board.c +++ b/arch/mips/cavium-octeon/executive/cvmx-helper-board.c @@ -211,8 +211,6 @@ int cvmx_helper_board_get_mii_address(int ipd_port) cvmx_helper_link_info_t __cvmx_helper_board_link_get(int ipd_port) { cvmx_helper_link_info_t result; - int phy_addr; - int is_broadcom_phy = 0; /* Unless we fix it later, all links are defaulted to down */ result.u64 = 0; @@ -248,8 +246,7 @@ cvmx_helper_link_info_t __cvmx_helper_board_link_get(int ipd_port) result.s.full_duplex = 1; result.s.speed = 1000; return result; - } else /* The other port uses a broadcom PHY */ - is_broadcom_phy = 1; + } break; case CVMX_BOARD_TYPE_BBGW_REF: /* Port 1 on these boards is always Gigabit */ @@ -267,108 +264,7 @@ cvmx_helper_link_info_t __cvmx_helper_board_link_get(int ipd_port) break; } - phy_addr = cvmx_helper_board_get_mii_address(ipd_port); - if (phy_addr != -1) { - if (is_broadcom_phy) { - /* - * Below we are going to read SMI/MDIO - * register 0x19 which works on Broadcom - * parts - */ - int phy_status = - cvmx_mdio_read(phy_addr >> 8, phy_addr & 0xff, - 0x19); - switch ((phy_status >> 8) & 0x7) { - case 0: - result.u64 = 0; - break; - case 1: - result.s.link_up = 1; - result.s.full_duplex = 0; - result.s.speed = 10; - break; - case 2: - result.s.link_up = 1; - result.s.full_duplex = 1; - result.s.speed = 10; - break; - case 3: - result.s.link_up = 1; - result.s.full_duplex = 0; - result.s.speed = 100; - break; - case 4: - result.s.link_up = 1; - result.s.full_duplex = 1; - result.s.speed = 100; - break; - case 5: - result.s.link_up = 1; - result.s.full_duplex = 1; - result.s.speed = 100; - break; - case 6: - result.s.link_up = 1; - result.s.full_duplex = 0; - result.s.speed = 1000; - break; - case 7: - result.s.link_up = 1; - result.s.full_duplex = 1; - result.s.speed = 1000; - break; - } - } else { - /* - * This code assumes we are using a Marvell - * Gigabit PHY. All the speed information can - * be read from register 17 in one - * go. Somebody using a different PHY will - * need to handle it above in the board - * specific area. - */ - int phy_status = - cvmx_mdio_read(phy_addr >> 8, phy_addr & 0xff, 17); - - /* - * If the resolve bit 11 isn't set, see if - * autoneg is turned off (bit 12, reg 0). The - * resolve bit doesn't get set properly when - * autoneg is off, so force it. - */ - if ((phy_status & (1 << 11)) == 0) { - int auto_status = - cvmx_mdio_read(phy_addr >> 8, - phy_addr & 0xff, 0); - if ((auto_status & (1 << 12)) == 0) - phy_status |= 1 << 11; - } - - /* - * Only return a link if the PHY has finished - * auto negotiation and set the resolved bit - * (bit 11) - */ - if (phy_status & (1 << 11)) { - result.s.link_up = 1; - result.s.full_duplex = ((phy_status >> 13) & 1); - switch ((phy_status >> 14) & 3) { - case 0: /* 10 Mbps */ - result.s.speed = 10; - break; - case 1: /* 100 Mbps */ - result.s.speed = 100; - break; - case 2: /* 1 Gbps */ - result.s.speed = 1000; - break; - case 3: /* Illegal */ - result.u64 = 0; - break; - } - } - } - } else if (OCTEON_IS_MODEL(OCTEON_CN3XXX) + if (OCTEON_IS_MODEL(OCTEON_CN3XXX) || OCTEON_IS_MODEL(OCTEON_CN58XX) || OCTEON_IS_MODEL(OCTEON_CN50XX)) { /* -- 2.7.4