From 064b53dbcc977dbf2753a67c2b8fc1c061d74f21 Mon Sep 17 00:00:00 2001 From: "John W. Linville" Date: Wed, 27 Jul 2005 10:19:44 -0400 Subject: [PATCH] [PATCH] PCI: restore BAR values after D3hot->D0 for devices that need it Some PCI devices (e.g. 3c905B, 3c556B) lose all configuration (including BARs) when transitioning from D3hot->D0. This leaves such a device in an inaccessible state. The patch below causes the BARs to be restored when enabling such a device, so that its driver will be able to access it. The patch also adds pci_restore_bars as a new global symbol, and adds a correpsonding EXPORT_SYMBOL_GPL for that. Some firmware (e.g. Thinkpad T21) leaves devices in D3hot after a (re)boot. Most drivers call pci_enable_device very early, so devices left in D3hot that lose configuration during the D3hot->D0 transition will be inaccessible to their drivers. Drivers could be modified to account for this, but it would be difficult to know which drivers need modification. This is especially true since often many devices are covered by the same driver. It likely would be necessary to replicate code across dozens of drivers. The patch below should trigger only when transitioning from D3hot->D0 (or at boot), and only for devices that have the "no soft reset" bit cleared in the PM control register. I believe it is safe to include this patch as part of the PCI infrastructure. The cleanest implementation of pci_restore_bars was to call pci_update_resource. Unfortunately, that does not currently exist for the sparc64 architecture. The patch below includes a null implemenation of pci_update_resource for sparc64. Some have expressed interest in making general use of the the pci_restore_bars function, so that has been exported to GPL licensed modules. Signed-off-by: John W. Linville Signed-off-by: Greg Kroah-Hartman --- arch/sparc64/kernel/pci.c | 6 +++++ drivers/pci/pci.c | 59 +++++++++++++++++++++++++++++++++++++++++++---- drivers/pci/setup-res.c | 2 +- include/linux/pci.h | 2 ++ include/linux/pci_regs.h | 1 + 5 files changed, 65 insertions(+), 5 deletions(-) diff --git a/arch/sparc64/kernel/pci.c b/arch/sparc64/kernel/pci.c index ec8bf40..9c17591 100644 --- a/arch/sparc64/kernel/pci.c +++ b/arch/sparc64/kernel/pci.c @@ -413,6 +413,12 @@ static int pci_assign_bus_resource(const struct pci_bus *bus, return -EBUSY; } +void pci_update_resource(struct pci_dev *dev, struct resource *res, int resno) +{ + /* Not implemented for sparc64... */ + BUG(); +} + int pci_assign_resource(struct pci_dev *pdev, int resource) { struct pcidev_cookie *pcp = pdev->sysdata; diff --git a/drivers/pci/pci.c b/drivers/pci/pci.c index c62d2f0..93ec158 100644 --- a/drivers/pci/pci.c +++ b/drivers/pci/pci.c @@ -222,6 +222,37 @@ pci_find_parent_resource(const struct pci_dev *dev, struct resource *res) } /** + * pci_restore_bars - restore a devices BAR values (e.g. after wake-up) + * @dev: PCI device to have its BARs restored + * + * Restore the BAR values for a given device, so as to make it + * accessible by its driver. + */ +void +pci_restore_bars(struct pci_dev *dev) +{ + int i, numres; + + switch (dev->hdr_type) { + case PCI_HEADER_TYPE_NORMAL: + numres = 6; + break; + case PCI_HEADER_TYPE_BRIDGE: + numres = 2; + break; + case PCI_HEADER_TYPE_CARDBUS: + numres = 1; + break; + default: + /* Should never get here, but just in case... */ + return; + } + + for (i = 0; i < numres; i ++) + pci_update_resource(dev, &dev->resource[i], i); +} + +/** * pci_set_power_state - Set the power state of a PCI device * @dev: PCI device to be suspended * @state: PCI power state (D0, D1, D2, D3hot, D3cold) we're entering @@ -239,7 +270,7 @@ int (*platform_pci_set_power_state)(struct pci_dev *dev, pci_power_t t); int pci_set_power_state(struct pci_dev *dev, pci_power_t state) { - int pm; + int pm, need_restore = 0; u16 pmcsr, pmc; /* bound the state we're entering */ @@ -278,14 +309,17 @@ pci_set_power_state(struct pci_dev *dev, pci_power_t state) return -EIO; } + pci_read_config_word(dev, pm + PCI_PM_CTRL, &pmcsr); + /* If we're in D3, force entire word to 0. * This doesn't affect PME_Status, disables PME_En, and * sets PowerState to 0. */ - if (dev->current_state >= PCI_D3hot) + if (dev->current_state >= PCI_D3hot) { + if (!(pmcsr & PCI_PM_CTRL_NO_SOFT_RESET)) + need_restore = 1; pmcsr = 0; - else { - pci_read_config_word(dev, pm + PCI_PM_CTRL, &pmcsr); + } else { pmcsr &= ~PCI_PM_CTRL_STATE_MASK; pmcsr |= state; } @@ -308,6 +342,22 @@ pci_set_power_state(struct pci_dev *dev, pci_power_t state) platform_pci_set_power_state(dev, state); dev->current_state = state; + + /* According to section 5.4.1 of the "PCI BUS POWER MANAGEMENT + * INTERFACE SPECIFICATION, REV. 1.2", a device transitioning + * from D3hot to D0 _may_ perform an internal reset, thereby + * going to "D0 Uninitialized" rather than "D0 Initialized". + * For example, at least some versions of the 3c905B and the + * 3c556B exhibit this behaviour. + * + * At least some laptop BIOSen (e.g. the Thinkpad T21) leave + * devices in a D3hot state at boot. Consequently, we need to + * restore at least the BARs so that the device will be + * accessible to its driver. + */ + if (need_restore) + pci_restore_bars(dev); + return 0; } @@ -809,6 +859,7 @@ struct pci_dev *isa_bridge; EXPORT_SYMBOL(isa_bridge); #endif +EXPORT_SYMBOL_GPL(pci_restore_bars); EXPORT_SYMBOL(pci_enable_device_bars); EXPORT_SYMBOL(pci_enable_device); EXPORT_SYMBOL(pci_disable_device); diff --git a/drivers/pci/setup-res.c b/drivers/pci/setup-res.c index 5598b47..362f933 100644 --- a/drivers/pci/setup-res.c +++ b/drivers/pci/setup-res.c @@ -26,7 +26,7 @@ #include "pci.h" -static void +void pci_update_resource(struct pci_dev *dev, struct resource *res, int resno) { struct pci_bus_region region; diff --git a/include/linux/pci.h b/include/linux/pci.h index 830c1ba..8878ccf 100644 --- a/include/linux/pci.h +++ b/include/linux/pci.h @@ -384,7 +384,9 @@ int pci_set_mwi(struct pci_dev *dev); void pci_clear_mwi(struct pci_dev *dev); int pci_set_dma_mask(struct pci_dev *dev, u64 mask); int pci_set_consistent_dma_mask(struct pci_dev *dev, u64 mask); +void pci_update_resource(struct pci_dev *dev, struct resource *res, int resno); int pci_assign_resource(struct pci_dev *dev, int i); +void pci_restore_bars(struct pci_dev *dev); /* ROM control related routines */ void __iomem *pci_map_rom(struct pci_dev *pdev, size_t *size); diff --git a/include/linux/pci_regs.h b/include/linux/pci_regs.h index 7dc391c..e2a089b 100644 --- a/include/linux/pci_regs.h +++ b/include/linux/pci_regs.h @@ -222,6 +222,7 @@ #define PCI_PM_CAP_PME_D3cold 0x8000 /* PME# from D3 (cold) */ #define PCI_PM_CTRL 4 /* PM control and status register */ #define PCI_PM_CTRL_STATE_MASK 0x0003 /* Current power state (D0 to D3) */ +#define PCI_PM_CTRL_NO_SOFT_RESET 0x0004 /* No reset for D3hot->D0 */ #define PCI_PM_CTRL_PME_ENABLE 0x0100 /* PME pin enable */ #define PCI_PM_CTRL_DATA_SEL_MASK 0x1e00 /* Data select (??) */ #define PCI_PM_CTRL_DATA_SCALE_MASK 0x6000 /* Data scale (??) */ -- 2.7.4