Tom Rini [Tue, 9 Apr 2019 02:32:11 +0000 (22:32 -0400)]
Merge git://git.denx.de/u-boot-riscv
- RISC-V arch support SMP.
- Support Andestech's PLIC and PLMT.
- qemu, fu54e, ae350 boards enable SMP by default.
- Fix CONFIG_DEFAULT_DEVICE_TREE failure.
Tom Rini [Tue, 9 Apr 2019 01:40:40 +0000 (21:40 -0400)]
Prepare v2019.04
Signed-off-by: Tom Rini <trini@konsulko.com>
Jagan Teki [Mon, 8 Apr 2019 20:27:54 +0000 (01:57 +0530)]
arm: sunxi: Enable DM_MMC on required SoCs
Enabling DM_MMC is forcing CONFIG_BLK=y so if any board which uses
SCSI must need to enable DM_SCSI otherwise SCSI reads on that particular
target making invalid reading to the disk drive.
Allwinner platform do support SCSI on A10, A20 and R40 SoC's out of
these only A10 have DM_SCSI enabled. So enabling DM_MMC on A20, R40
would eventually end-up with scsi disk read failures like [1]
So, enable DM_MMC in all places of respective SoC's instead of enabling
them globally to Allwinner platform.
Now, DM_MMC is enabled in Allwinner SoC's except A20 and R40.
[1] https://lists.denx.de/pipermail/u-boot/2019-April/364057.html
Reported-by: Pablo Sebastián Greco <pgreco@centosproject.org>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Tom Rini [Mon, 8 Apr 2019 14:11:29 +0000 (10:11 -0400)]
Merge tag 'fixes-for-2019.04-rc4' of git://git.denx.de/u-boot-staging
- i.MX8QXP-MEK ethernet fix
Andrejs Cainikovs [Fri, 1 Mar 2019 13:28:00 +0000 (13:28 +0000)]
dts: imx8qxp-mek: Add PHY post reset delay
PHY cannot be detected unless we wait about 150 ms.
Signed-off-by: Andrejs Cainikovs <andrejs.cainikovs@netmodule.com>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
Reviewed-by: Stefano Babic <sbabic@denx.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Andrejs Cainikovs [Fri, 1 Mar 2019 13:27:59 +0000 (13:27 +0000)]
net: dm: fec: Support phy-reset-post-delay property
As per Linux kernel DT binding doc:
- phy-reset-post-delay : Post reset delay in milliseconds. If present then
a delay of phy-reset-post-delay milliseconds will be observed after the
phy-reset-gpios has been toggled. Can be omitted thus no delay is
observed. Delay is in range of 1ms to 1000ms. Other delays are invalid.
Signed-off-by: Andrejs Cainikovs <andrejs.cainikovs@netmodule.com>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
Reviewed-by: Stefano Babic <sbabic@denx.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Acked-by: Lukasz Majewski <lukma@denx.de>
Stefan Roese [Wed, 3 Apr 2019 07:12:48 +0000 (09:12 +0200)]
watchdog: Move watchdog_dev to data section (BSS may not be cleared)
This patch moves all instances of static "watchdog_dev" declarations to
the "data" section. This may be needed, as the BSS may not be cleared
in the early U-Boot phase, where watchdog_reset() is already beeing
called. This may result in incorrect pointer access, as the check to
"!watchdog_dev" in watchdog_reset() may not be true and the function
may continue to run.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Heiko Schocher <hs@denx.de>
Cc: Tom Rini <trini@konsulko.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: "Marek Behún" <marek.behun@nic.cz>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Tested-by: Michal Simek <michal.simek@xilinx.com> (on zcu100)
Reviewed-by: Michal Simek <michal.simek@xilinx.com>
Rick Chen [Wed, 3 Apr 2019 02:43:37 +0000 (10:43 +0800)]
riscv: dts: fix CONFIG_DEFAULT_DEVICE_TREE failure
It occurs since commit
27cb7300ffda
("Ensure device tree DTS is compiled").
More details can refer to
89c2b5c02049aea746b1edee0b4e1d8519dec2f4
ARM: fix arch/arm/dts/Makefile
Signed-off-by: Rick Chen <rick@andestech.com>
Cc: Greentime Hu <greentime@andestech.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
Rick Chen [Tue, 2 Apr 2019 07:56:44 +0000 (15:56 +0800)]
riscv: ae350: enable SMP
Signed-off-by: Rick Chen <rick@andestech.com>
Cc: Greentime Hu <greentime@andestech.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
Rick Chen [Tue, 2 Apr 2019 07:56:43 +0000 (15:56 +0800)]
riscv: dts: ae350 support SMP
Signed-off-by: Rick Chen <rick@andestech.com>
Cc: Greentime Hu <greentime@andestech.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
Rick Chen [Tue, 2 Apr 2019 07:56:42 +0000 (15:56 +0800)]
riscv: ax25: Andes specific cache shall only support in M-mode
Limit the cache configuration only can be supported in M mode.
It can not be manipulated in S mode.
Signed-off-by: Rick Chen <rick@andestech.com>
Cc: Greentime Hu <greentime@andestech.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
Rick Chen [Tue, 2 Apr 2019 07:56:41 +0000 (15:56 +0800)]
riscv: ax25: Add platform-specific Kconfig options
Add ax25 RISC-V platform-specific Kconfig options,
to include CPU and timer drivers. Also disable
ATCPIT100 SoC timer and replace by PLMT.
Signed-off-by: Rick Chen <rick@andestech.com>
Cc: Greentime Hu <greentime@andestech.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
Rick Chen [Tue, 2 Apr 2019 07:56:40 +0000 (15:56 +0800)]
riscv: Add a SYSCON driver for Andestech's PLMT
The platform-Level Machine Timer (PLMT) block
holds memory-mapped mtime register associated
with timer tick.
This driver implements the riscv_get_time() which
is required by the generic RISC-V timer driver.
Signed-off-by: Rick Chen <rick@andestech.com>
Cc: Greentime Hu <greentime@andestech.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
Rick Chen [Tue, 2 Apr 2019 07:56:39 +0000 (15:56 +0800)]
riscv: Add a SYSCON driver for Andestech's PLIC
The Platform-Level Interrupt Controller (PLIC)
block holds memory-mapped claim and pending registers
associated with software interrupt. It is required
for handling IPI.
Signed-off-by: Rick Chen <rick@andestech.com>
Cc: Greentime Hu <greentime@andestech.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
Lukas Auer [Sun, 17 Mar 2019 18:28:42 +0000 (19:28 +0100)]
riscv: qemu: enable SMP
Signed-off-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
Reviewed-by: Anup Patel <anup.patel@wdc.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Lukas Auer [Sun, 17 Mar 2019 18:28:41 +0000 (19:28 +0100)]
riscv: fu540: enable SMP
Signed-off-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
Reviewed-by: Anup Patel <anup.patel@wdc.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Lukas Auer [Sun, 17 Mar 2019 18:28:40 +0000 (19:28 +0100)]
riscv: hang if relocation of secondary harts fails
Print an error message and hang if smp_call_function() returns an error,
indicating that relocation of the secondary harts has failed.
Signed-off-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Anup Patel <anup.patel@wdc.com>
Lukas Auer [Sun, 17 Mar 2019 18:28:39 +0000 (19:28 +0100)]
riscv: do not rely on hart ID passed by previous boot stage
RISC-V U-Boot expects the hart ID to be passed to it via register a0 by
the previous boot stage. Machine mode firmware such as BBL and OpenSBI
do this when starting their payload (U-Boot) in supervisor mode. If
U-Boot is running in machine mode, this task must be handled by the boot
ROM. Explicitly populate register a0 with the hart ID from the mhartid
CSR to avoid possible problems on RISC-V processors with a boot ROM that
does not handle this task.
Suggested-by: Rick Chen <rick@andestech.com>
Signed-off-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
Reviewed-by: Anup Patel <anup.patel@wdc.com>
Reviewed-by: Atish Patra <atish.patra@wdc.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Rick Chen <rick@andestech.com>
Tested-by: Rick Chen <rick@andestech.com>
Lukas Auer [Sun, 17 Mar 2019 18:28:38 +0000 (19:28 +0100)]
riscv: boot images passed to bootm on all harts
Signed-off-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
Reviewed-by: Anup Patel <anup.patel@wdc.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Lukas Auer [Sun, 17 Mar 2019 18:28:37 +0000 (19:28 +0100)]
riscv: add support for multi-hart systems
On RISC-V, all harts boot independently. To be able to run on a
multi-hart system, U-Boot must be extended with the functionality to
manage all harts in the system. All harts entering U-Boot are registered
in the available_harts mask stored in global data. A hart lottery system
as used in the Linux kernel selects the hart U-Boot runs on. All other
harts are halted. U-Boot can delegate functions to them using
smp_call_function().
Every hart has a valid pointer to the global data structure and a 8KiB
stack by default. The stack size is set with CONFIG_STACK_SIZE_SHIFT.
Signed-off-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
Reviewed-by: Anup Patel <anup.patel@wdc.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Lukas Auer [Sun, 17 Mar 2019 18:28:36 +0000 (19:28 +0100)]
riscv: save hart ID in register tp instead of s0
The hart ID passed by the previous boot stage is currently stored in
register s0. If we divert the control flow inside a function, which is
required as part of multi-hart support, the function epilog may not be
called, clobbering register s0. Save the hart ID in the unallocatable
register tp instead to protect the hart ID.
Signed-off-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Rick Chen <rick@andestech.com>
Reviewed-by: Anup Patel <anup.patel@wdc.com>
Lukas Auer [Sun, 17 Mar 2019 18:28:35 +0000 (19:28 +0100)]
riscv: delay initialization of caches and debug UART
Move the initialization of the caches and the debug UART until after
board_init_f_init_reserve. This is in preparation for SMP support, where
code prior to this point will be executed by all harts. This ensures
that initialization will only be performed once on the main hart running
U-Boot.
Signed-off-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
Reviewed-by: Anup Patel <anup.patel@wdc.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Lukas Auer [Sun, 17 Mar 2019 18:28:34 +0000 (19:28 +0100)]
riscv: implement IPI platform functions using SBI
The supervisor binary interface (SBI) provides the necessary functions
to implement the platform IPI functions riscv_send_ipi() and
riscv_clear_ipi(). Use it to implement them.
This adds support for inter-processor interrupts (IPIs) on RISC-V CPUs
running in supervisor mode. Support for machine mode is already
available for CPUs that include the SiFive CLINT.
Signed-off-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
Reviewed-by: Anup Patel <anup.patel@wdc.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Atish Patra <atish.patra@wdc.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Lukas Auer [Sun, 17 Mar 2019 18:28:33 +0000 (19:28 +0100)]
riscv: import the supervisor binary interface header file
Import the supervisor binary interface (SBI) header file from Linux
(arch/riscv/include/asm/sbi.h). The last change to it was in commit
6d60b6ee0c97 ("RISC-V: Device, timer, IRQs, and the SBI").
Signed-off-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
Reviewed-by: Anup Patel <anup.patel@wdc.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Atish Patra <atish.patra@wdc.com>
Lukas Auer [Sun, 17 Mar 2019 18:28:32 +0000 (19:28 +0100)]
riscv: add infrastructure for calling functions on other harts
Harts on RISC-V boot independently, U-Boot is responsible for managing
them. Functions are called on other harts with smp_call_function(),
which sends inter-processor interrupts (IPIs) to all other available
harts. Available harts are those marked as available in the device tree
and present in the available_harts mask stored in global data. The
available_harts mask is used to register all harts that have entered
U-Boot. Functions are specified with their address and two function
arguments (argument 2 and 3). The first function argument is always the
hart ID of the hart calling the function. On the other harts, the IPI
interrupt handler handle_ipi() must be called on software interrupts to
handle the request and call the specified function.
Functions are stored in the ipi_data data structure. Every hart has its
own data structure in global data. While this is not required at the
moment (all harts are expected to boot Linux), this does allow future
expansion, where other harts may be used for monitoring or other tasks.
Signed-off-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
Reviewed-by: Anup Patel <anup.patel@wdc.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Hannes Schmelzer [Fri, 29 Mar 2019 08:54:05 +0000 (09:54 +0100)]
net: phy: implement fallback mechanism for negative phy adresses
Negative phy-addresses can occour if the caller function was not able to
determine a valid phy address (from device-tree for example). In this
case we catch this here and search for ANY phy device on the given mdio-
bus.
Signed-off-by: Hannes Schmelzer <hannes.schmelzer@br-automation.com>
Tested-by: Michal Simek <michal.simek@xilinx.com>
Tested-by: Lukasz Majewski <lukma@denx.de>
Tom Rini [Fri, 5 Apr 2019 13:09:56 +0000 (09:09 -0400)]
Merge tag 'u-boot-imx-
20190405' of git://git.denx.de/u-boot-imx
Fixes for 2019.04
- fix bashism for MX8
- fix ethernet for MX53
- fix docs for i.MX8
Tom Rini [Wed, 3 Apr 2019 14:28:10 +0000 (10:28 -0400)]
Merge branch 'master' of git://git.denx.de/u-boot-usb
- Documentation fix
Tom Rini [Wed, 3 Apr 2019 14:26:57 +0000 (10:26 -0400)]
Merge branch '2019-04-03-master-imports'
- Important Khadas VIM2 fix
- Build fix for macOS Mojave
- Build fix for gcc-4.7 for host tools.
Thomas Petazzoni [Sat, 30 Mar 2019 14:29:23 +0000 (15:29 +0100)]
tools/Makefile: build host tools with -std=gnu99
Parts of the code are using C99 constructs (such as variables declared
inside loops), but also GNU extensions (such as typeof), so using
-std=gnu99 is necessary to build with older versions of gcc that don't
default to building with gnu99.
It fixes the following build failure:
./tools/../lib/crc16.c: In function "crc16_ccitt":
./tools/../lib/crc16.c:70:2: error: "for" loop initial declarations are only allowed in C99 mode
for (int i = 0; i < len; i++)
^
./tools/../lib/crc16.c:70:2: note: use option -std=c99 or -std=gnu99 to compile your code
when building the host tools with gcc 4.7.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
默默 [Sun, 31 Mar 2019 08:07:03 +0000 (16:07 +0800)]
fix compile error on macOS Mojave
Neil Armstrong [Wed, 3 Apr 2019 11:46:37 +0000 (13:46 +0200)]
configs: khadas_vim2: Fix defconfig
The Khadas VIM2 defconfig was missing the USB PHY config and
two other misc configs to setup dram banks and call misc_init_r.
Align it on the other Amlogic SoC based boards defconfig.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Neil Armstrong [Wed, 3 Apr 2019 11:46:36 +0000 (13:46 +0200)]
phy: Also allow MESON_GXM for MESON_GXL_USB_PHY
The MESON_GXL_USB_PHY is also used on the Amlogic Meson GXM SoCs.
Fixes: 2960e27e38 ("phy: Add Amlogic Meson USB2 & USB3 Generic PHY drivers")
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Eugen Hristev [Mon, 1 Apr 2019 11:04:03 +0000 (11:04 +0000)]
travis-ci: fix at91 missing boards
Fix missing at91 boards and split the at91 in two categories:
at91 arm v7
at91 arm926esj
which are the two main cores for the at91 architecture.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Lukasz Majewski [Mon, 1 Apr 2019 14:00:05 +0000 (16:00 +0200)]
DTS: Fix ETH PHY reset on HSC|DDC boards (imx53)
After the commit: "eth: dm: fec: Add gpio phy reset binding"
SHA1:
efd0b791069af93e9d439a70d1fe2ae8994dbbfa
The FEC ETH driver switched to PHY GPIO reset performed with data defined
in DTS.
For the HSC|DDC boards the GPIO reset signal is active low and hence the
wrong DTS description must be changed (otherwise the reset for ETH is not
properly setup).
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Lukasz Majewski [Mon, 1 Apr 2019 14:00:04 +0000 (16:00 +0200)]
cosmetic: Remove not needed string from kp_imx53.h config
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Lukasz Majewski [Mon, 1 Apr 2019 14:00:03 +0000 (16:00 +0200)]
cosmetic: config: Remove empty #ifdefs
After running tools/moveconfig.py it turned out that for various boards
there are an empty #ifdef statements.
Remove them to clean u-boot source code.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Krzysztof Kozlowski [Tue, 2 Apr 2019 07:32:12 +0000 (09:32 +0200)]
doc: Fix outdated ohci board hook documentation
The ohci driver calls board_usb_init(), not usb_board_init().
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Fabio Estevam [Wed, 13 Mar 2019 18:02:58 +0000 (15:02 -0300)]
imx8mq_evk: README: Make the underline marker fill the whole sentence
Let the underline marker "=" fill the whole sentence for better
readability.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Fabio Estevam [Wed, 13 Mar 2019 18:02:57 +0000 (15:02 -0300)]
imx8mq_evk: README: Fix a typo in the destination path
The DDR firmware binaries should be copied to '$(srctree)', so fix
a typo.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Fabio Estevam [Wed, 13 Mar 2019 18:02:56 +0000 (15:02 -0300)]
imx8mq_evk: README: Need to copy bl31.bin to U-Boot source tree
After building ATF it is needed to copy the generated bl31.bin file to
the U-Boot source tree.
Make this step explicit in the instructions.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Tom Rini [Tue, 2 Apr 2019 03:30:00 +0000 (23:30 -0400)]
Merge branch 'master' of git://git.denx.de/u-boot-sh
Minor fixes for the Alt board and PHY use on Gen2.
Tom Rini [Mon, 1 Apr 2019 16:31:22 +0000 (12:31 -0400)]
Merge branch 'master' of git://git.denx.de/u-boot-sunxi
- clk: sunxi: a10: Add CLK_AHB_GMAC
Jagan Teki [Thu, 28 Mar 2019 08:16:11 +0000 (13:46 +0530)]
clk: sunxi: a10: Add CLK_AHB_GMAC
CLK_AHB_GMAC was suppose to be part of previous commit
"clk: sunxi: Implement A10 EMAC clocks" add it so-that
we can get rid of sunxi_set_gate warning on boot message.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Baruch Siach [Wed, 2 Jan 2019 06:58:28 +0000 (08:58 +0200)]
tools/imx8m_image.sh: remove bashism
Use a single '=' to test string equality for compatibility with non-bash
shells. Otherwise, if /bin/sh is dash, build fails:
./tools/imx8m_image.sh: 15: [: signed_hdmi_imx8m.bin: unexpected operator
./tools/imx8m_image.sh: 15: [: signed_hdmi_imx8m.bin: unexpected operator
./tools/imx8m_image.sh: 15: [: spl/u-boot-spl-ddr.bin: unexpected operator
./tools/imx8m_image.sh: 15: [: spl/u-boot-spl-ddr.bin: unexpected operator
WARNING './spl/u-boot-spl-ddr.bin' not found, resulting binary is not-functional
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Tested-by: Chris Spencer <christopher.spencer@sea.co.uk>
Tom Rini [Mon, 1 Apr 2019 13:39:38 +0000 (09:39 -0400)]
Merge tag 'u-boot-imx-
20190401' of git://git.denx.de/u-boot-imx
Fixes for 2019.01
- pico-imx6ul: fix after conversion
- engicam boards
- pico-imx7d _ README due to hang with imx-usb-loader
Fabio Estevam [Wed, 27 Mar 2019 23:03:39 +0000 (20:03 -0300)]
pico-imx7d: README: Recommend the usage of a USB hub
Since commit
9e3c0174da842 ("pico-imx7d: Add LCD support") we started to
notice some hangs in U-Boot.
There is not an issue on such commit per se, but due to the LCD support
the current drawn is increased and this may cause issues when powering
pico-imx7d-pi from USB.
Some computers may be a bit strict with USB current draw and will
shut down their ports if the draw is too high.
The solution for that is to use an externally powered USB hub between the
board and the host computer.
Add such recommendation to the README file.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Jagan Teki [Thu, 21 Mar 2019 08:35:53 +0000 (14:05 +0530)]
configs: icorem6: Use imx6 cratch register for bootcount
SRAM address used for bootcount on exiting code is erasing
previous count value when system reset from Linux. So use
the dedicated imx6 scratch register, GPR2 to preserve the
contents even if the system reset from Linux.
Fixes: 4eb9aa39350e ("configs: imx6qdl_icore_mmc: Enable watchdog and bootcounter")
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Tested-by: Shyam Saini <shyam.saini@amarulasolutions.com>
Reviewed-by: Stefano Babic <sbabic@denx.de>
Michael Trimarchi [Fri, 8 Mar 2019 07:35:03 +0000 (13:05 +0530)]
configs: icore: Fix U-Boot proper loading from nand
SPL on Engicam i.Core M6 boards enabled DM, so it would require some
malloc() pool before relocation in order to load U-Boot proper properly.
So, enable SPL malloc() pool of 0x2000 size similarly like what we have
used for icore mmc defconfigs.
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Tested-by: Shyam Saini <shyam.saini@amarulasolutions.com>
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Adam Ford [Sun, 3 Mar 2019 22:22:45 +0000 (16:22 -0600)]
ARM: imx6q_logic: Enable UUID support
With UUID support, the root can now point to UUID. This makes
swiching between mmc 0 and mmc 1 easier by simplying changing
mmcdev between 0 and 1. From there, the scripts handle the rest.
Signed-off-by: Adam Ford <aford173@gmail.com>
Fabio Estevam [Thu, 21 Mar 2019 13:59:06 +0000 (10:59 -0300)]
pico-imx6ul: Fix eMMC boot after DM_MMC conversion
After the DM_MMC conversion the following eMMC boot error is observed:
U-Boot SPL 2019.04-rc4 (Mar 20 2019 - 18:53:28 +0000)
Trying to boot from MMC1
MMC Device 0 not found
spl: could not find mmc device 0. error: -19
SPL: failed to boot from all boot devices
### ERROR ### Please RESET the board ###
This happens because the SPL code does not initialize the SDHC pins
and clock.
Fix it by moving the original eMMC initialization from U-Boot proper
to SPL.
Reported-by: Otavio Salvador <otavio@ossystems.com.br>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Tested-by: Fabio Berton <fabio.berton@ossystems.com.br>
Reviewed-by: Otavio Salvador <otavio@ossystems.com.br>
Stefano Babic [Sun, 31 Mar 2019 17:54:10 +0000 (19:54 +0200)]
Merge branch 'master' of git://git.denx.de/u-boot
Signed-off-by: Stefano Babic <sbabic@denx.de>
Tom Rini [Sun, 31 Mar 2019 11:25:11 +0000 (07:25 -0400)]
Merge tag 'video-fixes-for-2019.04-rc4' of git://git.denx.de/u-boot-video
sunxi HDMI clock fix
Tom Rini [Sun, 31 Mar 2019 11:25:00 +0000 (07:25 -0400)]
Merge tag 'rockchip-fixes-for-2019.04' of git://git.denx.de/u-boot-rockchip
Last-minute fixes for Rockchip for 2019.04:
- reverts the deprecation of the 'download-key' detection
(with a full solution pending for the next release)
- applies a temporary fix for the 32bit pinctrl registers on the RK3288
Lukasz Majewski [Sat, 30 Mar 2019 15:22:21 +0000 (16:22 +0100)]
dfu: usb: Update MAINTAINERS file regarding DFU/USB gadget support
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Marek Vasut [Sat, 30 Mar 2019 07:24:19 +0000 (08:24 +0100)]
ARM: rmobile: alt: Fix I2C bus number
The I2C bus number to access the PMIC is I2C 7, fix this.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Marek Vasut [Sat, 30 Mar 2019 07:23:20 +0000 (08:23 +0100)]
ARM: dts: rmobile: Activate I2C7 on Alt
Activate I2C7 on Alt to allow access to the PMIC.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Marek Vasut [Sat, 30 Mar 2019 06:43:55 +0000 (07:43 +0100)]
ARM: rmobile: rcar-gen2: Activate bootm_size
Commit
d245059ff797 ("ARM: rmobile: rcar-gen3: Activate bootm_size")
only fixed the superfluous CONFIG_SYS_BOOTMAPSZ for R-Car Gen3, even
though it listed all affected boards. Apply the same fix to Gen2.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Fixes: d245059ff797 ("ARM: rmobile: rcar-gen3: Activate bootm_size")
Cc: Eugeniu Rosca <erosca@de.adit-jv.com>
Marek Vasut [Sat, 30 Mar 2019 06:05:09 +0000 (07:05 +0100)]
ARM: rmobile: Fix PHY LED mode register mask
The PHY LED mode register mask should be 0xc000 , not 0xc0000.
Correct the mask to operate on the right bits.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Marek Vasut [Sat, 30 Mar 2019 05:20:01 +0000 (06:20 +0100)]
ARM: rmobile: alt: Synchronize defconfig
Synchronize the R8A7794 Alt defconfig, enable DM SPI, DM SPI FLASH
and I2C driver support.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Marek Vasut [Sat, 30 Mar 2019 05:14:42 +0000 (06:14 +0100)]
ARM: rmobile: alt: Remove CLK2MHZ macro
The CLK2MHZ macro is unused, remove it.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Marek Vasut [Sat, 30 Mar 2019 05:10:49 +0000 (06:10 +0100)]
ARM: rmobile: alt: Remove R8A7794_ETHERNET_B
The R8A7794_ETHERNET_B config option is unused and based on the
description, this is a setting which should be fully done on a
DT level instead. Remove this config option.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Tom Rini [Fri, 29 Mar 2019 14:53:28 +0000 (10:53 -0400)]
Merge branch '2019-03-29-master-imports'
- Bugfixes:
- mmc: correct the HS400 initialization process
- configs: ti: Move FIT image load address to avoid overwrite
- lib: time: update module enable MACRO
- Add mbrugger as RPi board maintainer, correct agraf's email address.
Kever Yang [Fri, 29 Mar 2019 14:17:33 +0000 (22:17 +0800)]
lib: time: update module enable MACRO
We'd better use correct way to check if module has enabled.
for we have 3 timer MACRO:
- CONFIG_TIMER
- CONFIG_SPL_TIMER
- CONFIG_TPL_TIMER
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Heinrich Schuchardt [Thu, 28 Mar 2019 21:51:35 +0000 (22:51 +0100)]
doc/git-mailrc: correct entry 'agraf'
Correct Alex's email address.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Alexander Graf <agraf@csgraf.de>
Matthias Brugger [Thu, 28 Mar 2019 13:47:39 +0000 (14:47 +0100)]
RPi: Add mbrugger as board maintainer
I took over maintainership from Alex Graf with commit
3157bbfa18 ("rpi: Make Matthias maintainer")
But I forgot to update the board maintainer file.
This patch adds myself to the game.
Signed-off-by: Matthias Brugger <mbrugger@suse.com>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Alexander Graf <agraf@csgraf.de>
Andrew F. Davis [Tue, 26 Mar 2019 15:12:01 +0000 (10:12 -0500)]
configs: ti: Move FIT image load address to avoid overwrite
The FIT image is loaded to 0x8700_0000 followed by extracting from that
several large images also into the 0x8x00_0000 range. Large images
can end up overwriting the FIT image as it is being extracted from.
Move the FIT load address clear out to 0x9000_0000, this will require
a board to have at least 256MB of DRAM, if less then more careful
planning will be required for that platform.
Signed-off-by: Andrew F. Davis <afd@ti.com>
BOUGH CHEN [Tue, 26 Mar 2019 06:24:17 +0000 (06:24 +0000)]
mmc: correct the HS400 initialization process
After the commit
b9a2a0e2e9c0 ("mmc: Add support for downgrading
HS200/HS400 to HS mode"), it add a parameter in mmc_set_card_speed()
which indicates that the HS200/HS400 to HS downgrade is happening.
During the HS400 initialization, first select to HS200, and config
the related clock rate, then downgrade to HS mode. So here also need
to config the downgrade value to be true for two reasons. First,
make sure in the function mmc_set_card_speed(), after switch to HS
mode, first config the clock rate, then read the EXT_CSD, avoid
receiving data of EXT_CSD in HS mode at 200MHz. Second, after issue
the MMC_CMD_SWITCH command, it need to wait a bit then switch bus
properties.
Test on i.MX8QM MEK board, some Micron eMMC will stuck in transfer
mode in this case, and USDHC will never get data transfer complete
status, cause the uboot hang.
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
Acked-by: Marek Vasut <marek.vasut@gmail.com>
Tom Rini [Fri, 29 Mar 2019 13:21:30 +0000 (09:21 -0400)]
Merge tag 'efi-2019-04-rc5-2' of git://git.denx.de/u-boot-efi
Pull request for UEFI system for v2019.04-rc5-2
This patch series contains a bug fix for a double free in a UEFI unit
test. The other patches are documentation only (except for the definition
of two additional constants).
David Wu [Tue, 12 Feb 2019 11:51:51 +0000 (19:51 +0800)]
pinctrl: rockchip: Add 32bit writing function for rk3288 gpio0 pinctrl
There are no higher 16 writing corresponding bits for pmu_gpio0's
iomux/drive/pull at rk3288, need to read the value from register
firstly. Add the flag to distinguish it from normal registers.
Signed-off-by: David Wu <david.wu@rock-chips.com>
Philipp Tomsich [Fri, 29 Mar 2019 08:21:13 +0000 (09:21 +0100)]
Revert "rockchip: Drop call to rockchip_dnl_mode_check() for now"
Due to a final resolution not coming up in time for 2019.04 and
following the consensus on the discussion, we'll keep this around
for 2019.04 after all.
This reverts commit
0d968ceb1ff63b0d220a571f438f0d5fe6350e88.
Tom Rini [Fri, 29 Mar 2019 01:44:49 +0000 (21:44 -0400)]
Merge tag 'arc-last-minute-for-2019.04' of git://git.denx.de/u-boot-arc
This is last minute change which fixes problems in runtime on
AXS10x board caused by some changes in NAND framework and
tiny documentation improvement.
Anyways NAND flash storage was never really used on the board for various
reasons and now we decided to drop it for good.
Note this change only touches 1 ARC board so that should be safe for others.
As usual - build tested in TravisCI, see
https://travis-ci.org/abrodkin/u-boot/builds/
512041342
Jernej Skrabec [Sun, 24 Mar 2019 18:26:40 +0000 (19:26 +0100)]
sunxi: video: HDMI: Fix clock setup
Currently, HDMI driver doesn't consider minimum and maximum allowed rate
of pll3 (video PLL). It works most of the time, but not always.
Consider monitor with resolution 1920x1200, which has pixel clock rate
of 154 MHz. Current code would determine that pll3 rate has to be set to
154 MHz. However, minimum supported rate is 192 MHz. In this case video
output just won't work.
The reason why the driver is written in the way it is, is that at the
time HDMI PHY and clock configuration wasn't fully understood. But now
we have needed knowledge, so the issue can be fixed.
With this fix, clock configuration routine uses full range (1-16) for
clock divider instead of limited one (1, 2, 4, 11). It also considers
minimum and maximum allowed rate for pll3.
Fixes: 56009451d843 ("sunxi: video: Add A64/H3/H5 HDMI driver")
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Alexey Brodkin [Mon, 18 Feb 2019 12:03:34 +0000 (15:03 +0300)]
hsdk: readme: Suggest getting pyelftools with pip
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Suggested-by: Yunir Salimzyanov <yunir@synopsys.com>
Eugeniy Paltsev [Wed, 27 Mar 2019 13:53:43 +0000 (16:53 +0300)]
ARC: AXS10x: drop NAND support
On AXS10x boards we have non-standard NAND controller
which was never really used a lot as there're other much more
convenient [as they are standard & removable] persistent media
like SD-card and USB mass storage.
Moreover after recent changes we face with some NAND controller
runtime issues. So instead of keeping support of yet another
non-standard peripheral we're dropping its support for good.
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Heinrich Schuchardt [Thu, 28 Mar 2019 07:09:16 +0000 (08:09 +0100)]
efi_loader: define development target in README.uefi
Describe the target scope of the UEFI implementation in U-Boot.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Heinrich Schuchardt [Wed, 27 Mar 2019 21:02:30 +0000 (22:02 +0100)]
efi_loader: update TODOs in doc/README.uefi
The following TODOs are closed:
- GetNextVariableName is not implemented
- event groups
- manage events in a linked list
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Heinrich Schuchardt [Wed, 20 Mar 2019 17:47:07 +0000 (18:47 +0100)]
MAINTAINERS: adjust git repository for EFI PAYLOAD
The EFI PAYLOAD will use git://git.denx.de/u-boot-efi.git in future.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Heinrich Schuchardt [Wed, 27 Mar 2019 20:41:04 +0000 (21:41 +0100)]
efi_loader: TODO for the EFI file protocol
We currently only support EFI_FILE_PROTOCOL_REVISION while
UEFI specs 2.4 - 2.7 prescribe EFI_FILE_PROTOCOL_REVISION2.
Add a todo.
Add missing constants for the EFI file protocol revision.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Heinrich Schuchardt [Tue, 26 Mar 2019 04:56:31 +0000 (05:56 +0100)]
efi_selftest: avoid double free in dp utilities test
Avoid duplicate FreePool() in unit test for the device patch utilities
protocol.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Tom Rini [Wed, 27 Mar 2019 03:19:31 +0000 (23:19 -0400)]
Merge branch 'master' of git://git.denx.de/u-boot-socfpga
- configs: Stratix10: Remove CONFIG_USE_TINY_PRINTF
Tom Rini [Wed, 27 Mar 2019 03:19:11 +0000 (23:19 -0400)]
Merge branch 'master' of git://git.denx.de/u-boot-sh
- Various fixes for bugs found by u-boot test.py
Tom Rini [Wed, 27 Mar 2019 03:17:21 +0000 (23:17 -0400)]
Merge branch '2019-03-25-master-imports'
- Convert various SPI related options to Kconfig
Patrick Delaunay [Wed, 27 Feb 2019 14:20:38 +0000 (15:20 +0100)]
Convert CONFIG_ENV_SPI_* to Kconfig
This converts the following to Kconfig:
CONFIG_ENV_SPI_BUS
CONFIG_ENV_SPI_CS
CONFIG_ENV_SPI_MAX_HZ
CONFIG_ENV_SPI_MODE
Most of time these value are not needed, CONFIG_SF_DEFAULT
with same value is used, so I introduced CONFIG_USE_ENV_SPI_*
to force the associated value for the environment.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Patrick Delaunay [Wed, 27 Feb 2019 14:20:37 +0000 (15:20 +0100)]
Convert CONFIG_DEFAULT_SPI_* to Kconfig
This converts the following to Kconfig:
CONFIG_DEFAULT_SPI_BUS
CONFIG_DEFAULT_SPI_MODE
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Patrick Delaunay [Wed, 27 Feb 2019 14:20:36 +0000 (15:20 +0100)]
Convert CONFIG_SF_DEFAULT_* to Kconfig
This converts the following to Kconfig:
CONFIG_SF_DEFAULT_BUS
CONFIG_SF_DEFAULT_CS
CONFIG_SF_DEFAULT_MODE
CONFIG_SF_DEFAULT_SPEED
I use moveconfig script and then manual check on generated u-boot.cfg
to solve the remaining issue.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Patrick Delaunay [Wed, 27 Feb 2019 14:20:35 +0000 (15:20 +0100)]
tqma6s_wru4_mmc: manage board_spi_cs_gpio correctly
Define the function board_spi_cs_gpio only when needed,
only called in drivers/spi/mxc_spi.c.
That avoid compilation issue for tqma6s_wru4_mmc_defconfig
when CONFIG_SF_DEFAULT_BUS and CONFIG_SF_DEFAULT_CS are not
defined (CMD_SF not defined) after migration in KConfig.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Patrick Delaunay [Wed, 27 Feb 2019 14:20:34 +0000 (15:20 +0100)]
exynos: replace CONFIG_ENV_SPI_BASE by CONFIG_SYS_SPI_BASE
Replace CONFIG_ENV_SPI_BASE by the better CONFIG_SYS_SPI_BASE
(it is not the location for environment but the location for U-Boot)
and, as it is the only platform with use this define, remove
it from whitelist.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Patrick Delaunay [Wed, 27 Feb 2019 14:20:33 +0000 (15:20 +0100)]
controlcenterdc: move some configuration in defconfig file
Move some configurations in defconfig file
- CONFIG_CMD_I2C
- CONFIG_CMD_SPI
This allow correct dependency handling in Kconfig.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Patrick Delaunay [Wed, 27 Feb 2019 14:20:32 +0000 (15:20 +0100)]
bcm7445: move some configuration in defconfig file
Move some configurations in defconfig file
- CONFIG_DM_SPI (removed by syncing defconfigs )
- CONFIG_CMD_SF
- CONFIG_CMD_SPI
- CONFIG_CMD_SF_TEST
This allow correct dependency handling in Kconfig.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Tom Rini [Mon, 25 Mar 2019 21:26:38 +0000 (17:26 -0400)]
Merge branch '2019-03-25-master-imports'
- 3 bugfixes:
- mmc: Align MMC_TRACE with tiny printf
- scripts/Makefile.extrawarn: Silence more DTC warnings
- rsa: check that pointer checksum isn't NULL before using it
Marek Vasut [Mon, 18 Mar 2019 22:43:10 +0000 (23:43 +0100)]
mmc: tmio: Clamp SD_SECCNT to 16bit values on 16bit IP
On 16bit variants of the TMIO SD IP, the SECCNT register can only be
programmed to 16bit values, while on the 32bit and 64bit variants it
can be programmed to 32bit values. The SECCNT register indicates the
maximum number of blocks in a continuous transfer. Hence, limit the
maximum continuous transfer block count to 65535 blocks on 16bit
variants of the TMIO IP and to BIT(32)-1 blocks on 32bit and 64bit
variants.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Marek Vasut [Mon, 18 Mar 2019 05:04:17 +0000 (06:04 +0100)]
mmc: sh_mmcif: Set default MMCIF clock rate
Set MMCIF clock rate to 97.5 MHz, which is the default according
to Gen2 datasheet.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Marek Vasut [Mon, 18 Mar 2019 05:04:02 +0000 (06:04 +0100)]
clk: renesas: Add support for setting MMCIF clock divider on Gen2
Add code for configuring the MMC0CKCR/MMC1CKCR on Gen2 platforms.
This allows the MMCIF driver to set higher clock rate if desired.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Marek Vasut [Mon, 18 Mar 2019 04:38:08 +0000 (05:38 +0100)]
clk: renesas: Fix swapped div and mul in debug output on Gen2
The $div and $mul values were swapped in the debug output,
fix this.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Marek Vasut [Mon, 18 Mar 2019 04:11:42 +0000 (05:11 +0100)]
clk: renesas: Fix SDH clock divider decoding on Gen2
The gen2_clk_get_sdh_div() function is supposed to look up the
$val value read out of the SDCKCR register in the supplied table
and return the matching divider value. The current implementation
was matching the value from SDCKCR on the divider value in the
table, which is wrong. Fix this and rework the function a bit
to make it more readable.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Marek Vasut [Mon, 18 Mar 2019 02:20:31 +0000 (03:20 +0100)]
ARM: dts: rmobile: Increase off-on delay on the SD Vcc regulator
An ADATA 16GB Industrial MLC card has so much capacitance on the Vcc
pin that the usual toggling of regulator to power the card off and on
is insufficient. When the card is calibrated into UHS SDR104 mode, it
will remain in that mode across the power cycle and subsequent attempt
to communicate with the card will fail.
The test with this card is to insert it into an SDHI slot and perform
"mmc dev 0 ; mmc dev 0", where the second "mmc dev 0" will fail.
Fix this problem by increasing the off-on delay from 0 to 20 mS.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Ley Foon Tan [Fri, 22 Mar 2019 09:21:40 +0000 (17:21 +0800)]
configs: Stratix10: Remove CONFIG_USE_TINY_PRINTF
Use full printf instead of tiny printf in SPL.
Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
Marek Vasut [Sat, 23 Mar 2019 17:54:45 +0000 (18:54 +0100)]
mmc: Align MMC_TRACE with tiny printf
The tiny printf implementation only supports %x format specifier,
it does not support %X . Since it makes little difference whether
the debug output prints hex numbers in capitals or not, change it
to %x and make the MMC_TRACE output work with tiny printf too.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: Simon Glass <sjg@chromium.org>
Tom Rini [Fri, 22 Mar 2019 13:47:39 +0000 (09:47 -0400)]
scripts/Makefile.extrawarn: Silence more DTC warnings
While our "extrawarns" logic has gotten out of sync with upstream
Kbuild, for now lets start by bringing in the latest set of DTC_FLAGS
from the Linux Kernel 5.0 to match their behavior in silencing warnings
from dtc.
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Tom Rini <trini@konsulko.com>