[media] ttusb2: Don't use stack variables for DMA

The ttusb2_msg function uses on-stack variables to submit commands to
dvb_usb_generic.  This eventually gets to the DMA api layer and will throw a
traceback if the debugging options are set.

This allocates the temporary buffer variables with kzalloc instead.

Fixes https://bugzilla.redhat.com/show_bug.cgi?id=734506

Signed-off-by: Josh Boyer <jwboyer@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] it913x-fe ver 1.09 amend adc table entries

Amend adc table entries and size.

Signed-off-by: Malcolm Priestley <tvboxspy@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] it913x Support it9135 Verions 2 chip

Support for version 2 type chips and other LNA versions of version 1

Scripts may be compressed slightly at a later stage.

TODO
Firmware loader
However, things are a little confusing,  it is not clear that
dvb-usb-it9137-01.fw does not work with version 2 chips
as in recent files both firmwares are the same.

Should be applied to: 8133 Support for single ITE 9135 device.

Signed-off-by: Malcolm Priestley <tvboxspy@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] s5h1411: Calculate signal strength shown as percentage from SNR up to 35dB

As done first in lgdt330x.c, calculate signal strength from SNR up to 35dB
Even though the SNR can go higher than 35dB, there is some comfort factor
in having a range of strong signals that can show at 100%

Signed-off-by: Michael Krufky <mkrufky@kernellabs.com>
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Steven Toth <stoth@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] s5h1409: Calculate signal strength shown as percentage from SNR up to 35dB

As done first in lgdt330x.c, calculate signal strength from SNR up to 35dB
Even though the SNR can go higher than 35dB, there is some comfort factor
in having a range of strong signals that can show at 100%

Signed-off-by: Michael Krufky <mkrufky@kernellabs.com>
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Steven Toth <stoth@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] au8522: Calculate signal strength shown as percentage from SNR up to 35dB

As done first in lgdt330x.c, calculate signal strength from SNR up to 35dB
Even though the SNR can go higher than 35dB, there is some comfort factor
in having a range of strong signals that can show at 100%

Signed-off-by: Michael Krufky <mkrufky@kernellabs.com>
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Steven Toth <stoth@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] drivers/media/video/davinci/vpbe_display.c: eliminate a null pointer dereference

In the original code, probe_out could be reached when res was null and then
when the irq had not yet been requested.  In those cases, the call to
free_irq is not needed, so move probe_out down and introduce a new label
for the case where calling free_irq is useful.

The semantic match that finds this problem is as follows:

// <smpl>
@r@
expression E, E1;
identifier f;
statement S1,S2,S3;
@@

if (E == NULL)
{
  ... when != if (E == NULL || ...) S1 else S2
      when != E = E1
*E->f
  ... when any
  return ...;
}
else S3
// </smpl>

Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] drivers/media/video/atmel-isi.c: eliminate a null pointer dereference

The variable isi might be null or might be freed at the point of the call
to clk_put.  pclk contains the value that isi->pclk is expected to point to.

The semantic match that finds this problem is as follows:

// <smpl>
@r@
expression E, E1;
identifier f;
statement S1,S2,S3;
@@

if (E == NULL)
{
  ... when != if (E == NULL || ...) S1 else S2
      when != E = E1
*E->f
  ... when any
  return ...;
}
else S3
// </smpl>

Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] Make use of media bus pixel codes in adv7170 driver

The ADV7170/ADV7171 can operate in either 8-bit or 16-bit YCrCb Mode.

* 8-Bit YCrCb Mode
This default mode accepts multiplexed YCrCb inputs through
the P7-P0 pixel inputs. The inputs follow the sequence Cb0, Y0
Cr0, Y1 Cb1, Y2, etc. The Y, Cb and Cr data are input on a
rising clock edge.

* 16-Bit YCrCb Mode
This mode accepts Y inputs through the P7–P0 pixel inputs and
multiplexed CrCb inputs through the P15–P8 pixel inputs. The
data is loaded on every second rising edge of CLOCK. The inputs
follow the sequence Cb0, Y0 Cr0, Y1 Cb1, Y2, etc.

Signed-off-by: Christian Gmeiner <christian.gmeiner@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] FM1216ME_MK3 AUX byte for FM mode

Write AUX byte to FM1216ME_MK3 when FM mode, better sensitivity. It can be
usefull for other tuners.

Signed-off-by: Beholder Intl. Ltd. Dmitry Belimov <d.belimov@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] via-camera: disable RGB mode

The RGB mode does not work correctly. It captures fine at 640x480
but whenever the scaling engine is used to produce another resolution,
color corruption occurs (lots of erroneous pink and green).

It is not clear how the scaling engine is supposed to work and how
it knows which pixel format it is dealing with. Work around this
problem by disabling RGB support. YUYV scaling works just fine.

Test case:

gst-launch v4l2src ! video/x-raw-rgb,bpp=16,width=320,height=240 ! \
ffmpegcolorspace ! xvimagesink

Signed-off-by: Daniel Drake <dsd@laptop.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] Update some CARDLIST's

Re-run the cardlist script, in order to update the cardlists
for a few drivers, to sync with the driver changes.

Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] bttv: adding Sensoray 611 board to driver

commit affebd4db94b459f676a14d9bb696c3c2b73643d

[media] bttv: adding Sensoray 611 board to bttv driver

Signed-off-by: Dean Anderson <linux-dev@sensoray.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] saa7134: adding Sensoray boards to saa7134 driver

commit cf5886c3dd2f65c817cb6ca5e7202fa3a3bdc872

Signed-off-by: Dean Anderson <linux-dev@sensoray.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] v4l: mt9p031/mt9t001: Use i2c_smbus_{read|write}_word_swapped()

The MT9P031 and MT9T001 sensors transfer 16-bit data on the I2C bus in
swapped order. Let the I2C core handle byte order by using the
i2c_smbus_{read|write}_word_swapped() functions.

Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Jonathan Cameron <jic23@cam.ac.uk>
Acked-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] OMAP_VOUT: Increase MAX_DISPLAYS to a larger value

There is no limit to the number of displays that can registered with DSS2. The
current value of MAX_DISPLAYS is 3, set this to 10 so that the 'displays'
member of omap2video_device struct can store more omap_dss_device pointers.

This fixes a crash seen in omap_vout_probe when DSS2 registers for more than 3
displays.

Signed-off-by: Archit Taneja <archit@ti.com>
Acked-by: Vaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] OMAP_VOUT: Add support for DSI panels

Add support for DSI panels. DSI video mode panels will work directly. For
command mode panels, we will need to trigger updates regularly. This isn't done
by the omap_vout driver currently. It can still be supported if we connect a
framebuffer device to the panel and configure it in auto update mode.

Signed-off-by: Archit Taneja <archit@ti.com>
Acked-by: Vaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] OMAP_VOUT: Fix VSYNC IRQ handling in omap_vout_isr

Currently, in omap_vout_isr(), if the panel type is DPI, and if we
get either VSYNC or VSYNC2 interrupts, we proceed ahead to set the
current buffers state to VIDEOBUF_DONE and prepare to display the
next frame in the queue.

On OMAP4, because we have 2 LCD managers, the panel type itself is not
sufficient to tell if we have received the correct irq, i.e, we shouldn't
proceed ahead if we get a VSYNC interrupt for LCD2 manager, or a VSYNC2
interrupt for LCD manager.

Fix this by correlating LCD manager to VSYNC interrupt and LCD2 manager
to VSYNC2 interrupt.

Signed-off-by: Archit Taneja <archit@ti.com>
Reviewed-by: Sumit Semwal <sumit.semwal@ti.com>
Acked-by: Vaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] OMAP_VOUT: CLEANUP: Remove redundant code from omap_vout_isr

Currently, there is a lot of redundant code is between DPI and VENC panels, this
can be made common by moving out field/interlace specific code to a separate
function called omapvid_handle_interlace_display(). There is no functional
change made.

Signed-off-by: Archit Taneja <archit@ti.com>
Reviewed-by: Sumit Semwal <sumit.semwal@ti.com>
Acked-by: Vaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] OMAP_VOUT: Fix check in reqbuf for buf_size allocation

The commit 383e4f69879d11c86ebdd38b3356f6d0690fb4cc makes reqbuf prevent
requesting a larger size buffer than what is allocated at kernel boot during
omap_vout_probe.

In omap_vout_buffer_setup callback API, the requested size is compared with
vout->buffer_size, this isn't correct as vout->buffer_size is later set to the
size requested in reqbuf. When the video device is opened the next time, this
check will prevent us to allocate a buffer which is larger than what we requested
the last time.

Don't use vout->buffer_size, always check with the parameters video1_bufsize
or video2_bufsize.

Signed-off-by: Archit Taneja <archit@ti.com>
Acked-by: Vaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] v4l: use i2c_smbus_read_word_swapped

Function ensures that error codes don't get mangled.
Dependant on:
which is working it's way through the i2c tree.

Signed-off-by: Jonathan Cameron <jic23@cam.ac.uk>
Acked-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] anysee: fix style issues

Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] anysee: add control message debugs

Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] anysee: CI/CAM support

Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] anysee: I2C gate control DNOD44CDH086A tuner module

DNOD44CDH086A (NXP TDA18212) tuner module is not connected to
demodulator I2C gate. Instead demodulator gate it uses external
GPIO driven gate. Override demodulator I2C gate control with
own in that case.

Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] anysee: add support for Anysee E7 T2C

Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] tda18212: add DVB-T2 support

Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] solo6x10: fix broken Makefile

The Makefile used := instead of +=, this broke the compatibility build.

Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] solo6x10: rename jpeg.h to solo6x10-jpeg.h

This header clashes with the jpeg.h in gspca when doing a compatibility
build using the media_build system.

Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] saa7134.h: Suppress compiler warnings when CONFIG_VIDEO_SAA7134_RC is not set

If the said config optio is not set, the compiler will spill out many
warnings about statements with no effect, such as:

Casting the zero to void will cure the warning.

Signed-off-by: Timo Kokkonen <kaapeli@itanic.dy.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] it913x [VER 1.07] Support for single ITE 9135 devices

Support for single ITE 9135 device.

Only single devices have been tested.  Dual ITE 9135 devices
should work, but have not been tested.

TODOs
support for ver 2 chip
config for other tuner types.
rework of firmware file.

Signed-off-by: Malcolm Priestley <tvboxspy@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] Support for Terratec G1

Hi,

This is a little patch to support Terratec G1 (based on Terratec Grabby).

It works perfectly on my pc (Ubuntu 11.04 / Kernel 2.6.38).

Best regards,

Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] cx25821: off by one in cx25821_vidioc_s_input()

If "i" is 2 then when we call cx25821_video_mux() we'd end up going
past the end of the cx25821_boards[dev->board]->input[].

The INPUT() macro obfuscates what's going on in that function so it's
a bit hard to follow.  And as Mauro points out the hard coded 2 is
not very helpful.

Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] media: tea5764: reconcile Kconfig symbol and macro

The Kconfig symbol RADIO_TEA5764_XTAL is unused. The code does use a
RADIO_TEA5764_XTAL macro, but does that rather peculiar. But there seems
to be a way to keep both. (The easiest way out would be to rip out both
the Kconfig symbol and the macro.)

Note there's also a module parameter 'use_xtal' to influence all this.

Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Acked-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] omap_vout: Add poll() support

Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Vaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] omap3isp: preview: Add crop support on the sink pad

The crop rectangle takes the preview engine internal cropping
requirements into account. The smallest allowable margins are 14 columns
and 8 rows when reading from memory, and 18 columns and 8 rows when
processing data on the fly from the CCDC.

Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] omap3isp: preview: Rename min/max input/output sizes defines

The macros that define the minimum/maximum input and output sizes are
defined in seperate files and have no consistent naming. In preparation
for preview engine cropping support, move them all to isppreview.c and
rename them to PREV_{MIN|MAX}_{IN|OUT}_{WIDTH|HEIGHT}*.

Remove unused and/or unneeded local variables that store the maximum
output width.

Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] omap3isp: preview: Remove horizontal averager support

The horizontal averager isn't used and will get in the way when
implementing cropping support on the input pad. Remove it, it can be
added back later if needed.

Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] omap3isp: Report the ISP revision through the media controller API

Set the media_device::hw_revision field to the ISP revision number.

Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] omap3isp: ccdc: remove redundant operation

Trivial arithmetics clean up.

Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] omap3isp: Fix memory leaks in initialization error paths

Make sure all modules init functions clean up after themselves in case
of error.

Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reported-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] omap3isp: Add missing mutex_destroy() calls

Mutexes must be destroyed with mutex_destroy(). Add missing calls in the
modules cleanup handlers.

Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] omap3isp: Move *_init_entities() functions to the init/cleanup section

Group all init/cleanup functions together to make the code more
readable.

Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] omap3isp: Move media_entity_cleanup() from unregister() to cleanup()

The media_entity_cleanup() function belong to the module cleanup
handlers, not the entity registration handlers. Move it there.

Create a omap3isp_video_cleanup() function to cleanup the video node
entity, and call it from the module cleanup handlers.

Rename omap3isp_stat_free() to omap3isp_stat_cleanup().

Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] MFC: Change MFC firmware binary name

This patch renames the MFC firmware binary to avoid SoC name in it.

Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Acked-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] vb2: add vb2_get_unmapped_area in vb2 core

no mmu system needs get_unmapped_area file operations to do mmap

Signed-off-by: Scott Jiang <scott.jiang.linux@gmail.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] v4l: Add v4l2 subdev driver for S5K6AAFX sensor

This driver exposes preview mode operation of the S5K6AAFX sensor with
embedded SoC ISP. The native capture (snapshot) operation mode is not
supported.
Following controls are available:
 manual/auto exposure and gain, power line frequency (anti-flicker),
 saturation, sharpness, brightness, contrast, white balance temperature,
 color effects, horizontal/vertical image flip, frame interval,
 auto white balance.
RGB component gains are currently exposed through private controls.

Reviewed-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] v4l: Add AUTO option for the V4L2_CID_POWER_LINE_FREQUENCY control

V4L2_CID_POWER_LINE_FREQUENCY control allows applications to instruct
a driver what is the power line frequency so an appropriate filter
can be used by the device to cancel flicker by compensating the light
intensity ripple. Currently in the menu we have entries for 50 Hz and
60 Hz and for entirely disabling the anti-flicker filter.
However some devices are capable of automatically detecting the
frequency, so add V4L2_CID_POWER_LINE_FREQUENCY_AUTO entry for them.

Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] media: ov6650: stylistic improvements

* with no "retrun ret;" at the end, there is no need to initialize ret
  any longer,
* consequently use conditional expressions, not if...else constructs,
  throughout ov6650_s_ctrl(),
* v4l2_ctrl_new_std_menu() max value of V4L2_EXPOSURE_MANUAL instead of
  equivalent 1 looks more clear.

Created on top of "Converting soc_camera to the control framework"
series.

Signed-off-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] media: ov5642: Add support for arbitrary resolution

This patch adds the ability to get arbitrary resolutions with a width
up to 2592 and a height up to 720 pixels instead of the standard 1280x720
only.

Signed-off-by: Bastian Hecht <hechtb@gmail.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] V4L: replace soc-camera specific soc_mediabus.h with v4l2-mediabus.h

Most users of the <media/soc_mediabus.h> header only need pixel code
definitions, which are now located in the generic <linux/v4l2-mediabus.h>
header. Switch over to reduce soc-camera dependencies.

Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] V4L: soc-camera: make (almost) all client drivers re-usable outside of the framework

The most important change in this patch is direct linking to struct
soc_camera_link via the client->dev.platform_data pointer. This makes most
of the soc-camera client drivers also usable outside of the soc-camera
framework. After this change all what is needed for these drivers to
function are inclusions of soc-camera headers for some convenience macros,
suitably configured platform data, which is anyway always required, and
loaded soc-camera core module for library functions. If desired, these
library functions can be made generic in the future and moved to a more
neutral location.

The only two client drivers, that still depend on soc-camera are:

mt9t031: it uses struct video_device for its PM. Since no hardware is
available, alternative methods cannot be tested.

ov6650: it uses struct soc_camera_device to pass its sense data back to
the bridge driver. A generic v4l2-subdevice approach should be developed
to perform this.

Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] V4L: add .g_std() core V4L2 subdevice operation

VIDIOC_G_STD can return the current TV-norm to the user in one of two ways:
if an .vidioc_g_std() ioctl operation is provided by the driver, it is
called, otherwise the value ot the .current_norm field of struct
video_device is returned. Since subdevice drivers currently have no access
to struct video_device objects, the only way to provide this information to
the user is by implementing a .g_std() method.

Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] V4L: dynamically allocate video_device nodes in subdevices

Currently only very few drivers actually use video_device nodes, embedded
in struct v4l2_subdev. Allocate these nodes dynamically for those drivers
to save memory for the rest.

Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Tested-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] V4L: sh_mobile_csi2: fix unbalanced pm_runtime_put()

If the sh_mobile_csi2 driver didn't attach to a client, normally, because
the respective device connects to the SoC over the parallel CEU interface
and doesn't use the CSI-2 controller, it also shouldn't call
pm_runtime_put() on attempted disconnect.

Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] V4L: mt9m001, mt9v022: use internally cached pixel code

Using the internally cached pixel code, instead of the one, provided by
the soc-camera, removes one more use of struct soc_camera_device in these
drivers. Also remove the no longer needed soc_camera_from_i2c() inline
function.

Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] V4L: soc-camera: start removing struct soc_camera_device from client drivers

Remove most trivial uses of struct soc_camera_device from most client
drivers, abstracting some of them inside inline functions. Next steps
will eliminate remaining uses and modify inline functions to not use
struct soc_camera_device.

Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] V4L: docbook documentation for struct v4l2_create_buffers

Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] soc_camera: remove the now obsolete struct soc_camera_ops

Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
[g.liakhovetski@gmx.de: mt9m001 hunk moved to an earlier patch]
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] mt9t031: convert to the control framework

Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
[g.liakhovetski@gmx.de: simplified pointer arithmetic]
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] mt9m111: convert to the control framework

Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
[g.liakhovetski@gmx.de: simplified pointer arithmetic]
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] mt9m001: convert to the control framework

Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
[g.liakhovetski@gmx.de: simplified pointer arithmetic]
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] ov9740: convert to the control framework

Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] ov6650: convert to the control framework

Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
[g.liakhovetski@gmx.de: simplified pointer arithmetic]
[jkrzyszt@tis.icnet.pl: fix a typo in the register name]
Acked-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] ov2640: convert to the control framework

Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] mt9v022: convert to the control framework

Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
[g.liakhovetski@gmx.de: simplified pointer arithmetic]
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] rj54n1cb0c: convert to the control framework

Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
[g.liakhovetski@gmx.de: simplified pointer arithmetic]
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] V4L: soc-camera: call subdevice .s_power() method, when powering up or down

Currently soc-camera can use power regulators and platform specific
methods to power clients up and down. Additionally, client drivers can
provide their own subdevice .s_power() methods, acting directly on the
device. This patch adds calls to this method, when external power
supplies are on.

Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] V4L: soc_camera_platform: do not leave dangling invalid pointers

The life-time of soc-camera device objects can be longer, than the
time, it is attached to a client driver, therefore all references to
the driver own data have to be cleared, when the driver is detached.

Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] V4L: soc-camera: split a function into two

The soc_camera_power_set() function processes two cases: power on anf off.
These two cases don't share and common code, and the function is always
called with a constant power on / off argument. Splitting this function
into two removes a condition check, reduces indentation levels and makes
the code look cleaner.

Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] V4L: sh_mobile_csi2: do not guess the client, the host tells us

We do not have to scan the list of subdevices to find our client - the
sensor, the host has already set our grp_id value.

Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] V4L: sh_mobile_ceu_camera: the host shall configure the pipeline

It is a task of the host / bridge driver to bind single subdevices into a
pipeline, not of respective subdevices. Eventually this might be handled
by the Media Controller API.

Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] V4L: soc-camera: add 2 new ioctl() handlers

This patch adds two new ioctl() handlers: .vidioc_create_bufs() and
.vidioc_prepare_buf() for compliant vb2 soc-camera hosts.

Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] V4L: mx3-camera: prepare to support multi-size buffers

Prepare the mx3_camera friver to support the new VIDIOC_CREATE_BUFS and
VIDIOC_PREPARE_BUF ioctl()s. The .queue_setup() vb2 operation must be
able to handle buffer sizes, provided by the caller, and the
.buf_prepare() operation must not use the currently configured frame
format for its operation, which makes it superfluous for this driver.
Its functionality is moved into .buf_queue().

Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] V4L: sh-mobile-ceu-camera: prepare to support multi-size buffers

Prepare the sh_mobile_ceu_camera friver to support the new
VIDIOC_CREATE_BUFS and VIDIOC_PREPARE_BUF ioctl()s. The .queue_setup()
vb2 operation must be able to handle buffer sizes, provided by the
caller, and the .buf_prepare() operation must not use the currently
configured frame format for its operation.

Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] ov772x: convert to the control framework

Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
[g.liakhovetski@gmx.de: simplified pointer arithmetic]
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] ov9640: convert to the control framework

Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] sh_mobile_ceu_camera: implement the control handler

And since this is the last and only host driver that uses controls, also
remove the now obsolete control fields from soc_camera.h.

Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
[g.liakhovetski@gmx.de: moved code around, fixed problems]
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] soc_camera: add control handler support

The soc_camera framework is switched over to use the control framework.
After this patch none of the controls in subdevs or host drivers are available,
until those drivers are also converted to the control framework.

Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
[g.liakhovetski@gmx.de: moved code around, fixed problems]
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] dmaengine: ipu-idmac: add support for the DMA_PAUSE control

To support multi-size buffers in the mx3_camera V4L2 driver we have to be
able to stop DMA on a channel without releasing descriptors and completely
halting the hardware. Use the DMA_PAUSE control to implement this mode.

Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Vinod Koul <vinod.koul@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] V4L: vb2: add support for buffers of different sizes on a single queue

The two recently added ioctl()s VIDIOC_CREATE_BUFS and VIDIOC_PREPARE_BUF
allow user-space applications to allocate video buffers of different
sizes and hand them over to the driver for fast switching between
different frame formats. This patch adds support for buffers of different
sizes on the same buffer-queue to vb2.

Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] V4L: vb2: prepare to support multi-size buffers

In preparation for the forthcoming VIDIOC_CREATE_BUFS ioctl add a
"const struct v4l2_format *" argument to the .queue_setup() vb2
operation.

Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] V4L: document the new VIDIOC_CREATE_BUFS and VIDIOC_PREPARE_BUF ioctl()s

[mchehab@redhat.com: remove emacs format crap at the end of the new files]
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] V4L: videobuf2: update buffer state on VIDIOC_QBUF

V4L2 specification states, that the videobuffer state flags have to be
updated on VIDIOC_QBUF ioctl(). Videobuf2 currently doesn't do that,
which is fixed by this patch.

Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] V4L: add two new ioctl()s for multi-size videobuffer management

A possibility to preallocate and initialise buffers of different sizes
in V4L2 is required for an efficient implementation of a snapshot
mode. This patch adds two new ioctl()s: VIDIOC_CREATE_BUFS and
VIDIOC_PREPARE_BUF and defines respective data structures.

Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] V4L: add a new videobuf2 buffer state VB2_BUF_STATE_PREPARED

This patch prepares for a better separation of the buffer preparation
stage.

Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] V4L: omap1-camera: fix Oops with NULL platform data

Consistently check for platform data != NULL before dereferencing.

Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] V4L: sh-mobile-ceu-camera: fix mixed CSI2 & parallel camera case

The current sh_mobile_ceu_camera driver can cause an Oops, if a CSI2 and a
parallel camera are registered on the same CEU. Fix it by making CSI2
association with a camera more targeted.

Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] V4L: mt9t112: fix broken cropping and scaling

G_CROP, S_CROP, CROPCAP, G_FMT, and S_FMT functionality in the mt9t112
driver was broken on many occasions. This patch allows consistent
cropping for rectangles also larger than VGA and cleans up multiple
other issues in this area. It still doesn't add support for proper
scaling, using the sensor own scaler, so input window is still
always equal to the output frame.

Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] V4L: soc-camera: remove soc-camera client bus-param operations and supporting code

soc-camera has been completely ported over to V4L2 subdevice mbus-config
operations, soc-camera client bus-param operations and supporting code
can now be removed.

Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] V4L: tw9910: remove superfluous soc-camera client operations

Now that all soc-camera hosts have been ported to use V4L2 subdevice
mediabus-config operations and soc-camera client bus-parameter operations
have been made optional, they can be removed.

Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] V4L: soc_camera_platform: remove superfluous soc-camera client operations

Now that all soc-camera hosts have been ported to use V4L2 subdevice
mediabus-config operations and soc-camera client bus-parameter operations
have been made optional, they can be removed.

Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] ARM: mach-shmobile: mackerel doesn't need legacy SOCAM_* flags anymore

The sh_mobile_ceu_camera driver has been converted to use the V4L2
subdevice .[gs]_mbus_config() operations, therefore we don't need
SOCAM_* flags for the soc_camera_platform driver anymore. Remove
them.

Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] V4L: sh_mobile_csi2: remove superfluous soc-camera client operations

Now that all soc-camera hosts have been ported to use V4L2 subdevice
mediabus-config operations and soc-camera client bus-parameter operations
have been made optional, they can be removed.

Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] V4L: rj54n1cb0c: remove superfluous soc-camera client operations

Now that all soc-camera hosts have been ported to use V4L2 subdevice
mediabus-config operations and soc-camera client bus-parameter operations
have been made optional, they can be removed.

Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] V4L: ov9740: remove superfluous soc-camera client operations

Now that all soc-camera hosts have been ported to use V4L2 subdevice
mediabus-config operations and soc-camera client bus-parameter operations
have been made optional, they can be removed.

Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] V4L: ov9640: remove superfluous soc-camera client operations

Now that all soc-camera hosts have been ported to use V4L2 subdevice
mediabus-config operations and soc-camera client bus-parameter operations
have been made optional, they can be removed.

Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] V4L: ov772x: remove superfluous soc-camera client operations

Now that all soc-camera hosts have been ported to use V4L2 subdevice
mediabus-config operations and soc-camera client bus-parameter operations
have been made optional, they can be removed.

Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] sh: migor: remove unused ov772x buswidth flag

The ov772x driver only supports 8 bits per sample pixel codes, hence
the OV772X_FLAG_8BIT flag has no effect. Remove it.

Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] sh: ap3rxa: remove redundant soc-camera platform data fields

The sh_mobile_ceu_camera driver has been converted to use the V4L2
subdevice .[gs]_mbus_config() operations, therefore we don't need
SOCAM_* flags for the soc_camera_platform driver anymore. The ov772x
driver only supports 8 bits per sample pixel codes, hence the
OV772X_FLAG_8BIT flag has no effect. Remove both of them.

Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>